Home
Support
Product Support
Optical Networking
Cisco Network Convergence System 1000 Series
Configuration Guides

Configuration Guide for Cisco Optical Site Manager, IOS XR Release 26.x.x

Releases

26.x.x
25.x.x
24.3.x
24.2.x
24.1.x
7.11.x

View all Saved Content

PDF

Is this content helpful?

Helpful Unhelpful

Suggestions for Improvement

Thank you for your feedback. Your response has been recorded.

Ask about this content

Configuration Guide for Cisco Optical Site Manager, IOS XR Release 26.x.x

Expand all sections

About this content

Cisco Optical Site Manager

Cisco Optical Site Manager

Use the Node Functional View

Node functional view
View node details
Optical channel monitoring
Optical time domain reflectometer
Connection verification
Customize NFV layout

Use Cisco Optical Site Manager Topology

Topology

Monitor Faults

Fault monitoring
Alarm profiles
User tags

Configure devices

Create or edit an authorization group
Add a device
SVO-LC device onboard in R25.1.1

Provision line cards

Supported NCS 1000 line cards
Configure the administrative state of Pluggable Port Modules and line cards
Open the card view
Provision an NCS 1000 or NCS 2000 card
Add card mode for NCS 1000 cards
Configuring card modes for NCS 2000 line cards
Reset a line card
Provision SONET or SDH trace monitoring
Provision trail trace monitoring
Provision ODU interfaces
Provision OTU interfaces
Provision Ethernet interfaces
Provision SONET or SDH Interfaces
Provision optical channels
Change Trunk Port Parameters
Provision optical threshold settings
Configure G.709 thresholds
Provision FEC thresholds
Configure RMON thresholds
Configure loopback interfaces
Configure optical safety
Configure thresholds for SONET or SDH
Enable attention LED
PSM card protection mechanism
View performance monitoring parameters
SVO cards
View UDC details
View insertion loss parameters
Manage the protection group
Provisioning optical amplifier cards
Retrieve MAC addresses through lldp
Provision FPD upgrade for the ports
Provision FPD upgrade for mr-mxp card
Enable proactive protection
Provision odu circuit
Functional Module Group
Provision zr plus interfaces
Provision zr plus interfaces
Provision zr plus trail trace monitoring
Provision zr plus trail trace monitoring
Provision Pluggable Ports
View circuit protection parameters
NCS 2000 Cards

Configure the node

Import a Cisco Optical Network Planner configuration file
Optical degrees
Internal patch cords
Automatic power control
Span loss measurement
Configure amplifier parameters
Provision interface parameters
Provision Raman amplifier parameters
Manage Raman interface parameters
Optical cross-connect circuits
Submarine Line Terminating Equipment mode
GMPLS UNI circuit connections
External links
Remote node management using GCC

Backup and restore database

Database backup and restore

Change IP addresses

Cisco Optical Site Manager IP address changes

Upgrade software

Cisco Optical Site Manager software packages
Workflow for software upgrade
Download GISO image
Download software package on device
Activate NCS 1000 and NCS 2000 device software
Activate Cisco Optical Site Manager and admin plane image for the SVO-lc
Delete software package

View inventory

View inventory of all racks or chassis
View inventory of a rack or chassis

User access and authentication

User configuration settings
Single sign-on (SSO)
Manage external authentication
x509 certificates
Active login user details
Session timeout

High-availability server operations

HA Servers view

Cisco Optical Site Manager settings

Configure time zone and measurement units
Configure NTP servers for node time synchronization
View audit logs
Download device diagnostics
Download ShowTech logs
Smart licensing for Cisco Optical Site Manager
Description
Configure smart transport
Cisco smart license utility
Configure CSLU
Configure offline

Configuration Guide for Cisco Optical Site Manager, IOS XR Release 26.x.x

Provision FPD upgrade for the ports

Updated: October 14, 2026

Want to summarize with AI?

Use this procedure to provision FPD upgrade for the ports in Cisco Optical Site Manager. Each trunk port has separate upgrade alarm.

Use this task to provision FPD upgrade for the ports.

When the firmware version on the DCO trunk port is earlier than the NCS 2000 package firmware version, an alarm "FPD-UPG-REQUIRED" is raised on that trunk port in the Alarms tab. Each trunk port has separate upgrade alarm.

You can view the DCO running firmware version and the NCS 2000 package firmware version under the Maintenance > FPD upgrade tabs.

Use this task to upgrade DCO (trunk ports) on the 1.2T-MXP card with the latest firmware released as part of the NCS 2000 software release.

Before you begin

Log into Cisco Optical Site Manager
Open the card view

Follow these steps to provision FPD upgrade for the ports.

Procedure

Click the Maintenance > FPD Upgrade tabs.
Click FPD upgrade to perform firmware upgrade for the chosen ports.

After the firmware upgrade is completed successfully, the "FPD-UPG-REQUIRED" alarm gets cleared in the Alarms tab and you can view the updated running firmware version in the FPD Upgrade table.

Note

Traffic affecting DCO upgrade is not supported in Release 12.2.

The provision FPD upgrade for the ports task is complete.

Need help?

Open a support case

(Requires a Cisco Service Contract)

Bias-free language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.