Use this procedure to verify the AINS soak status and timer information for various controller types.
Use this task to view the current AINS configuration status, including the soak state and remaining duration, for various controller types.
The AINS Soak field in the output indicates the current state of AINS. The current state can be None, Pending, or Running. The Total Duration field indicates the total soak time period that is configured. The Remaining Duration field indicates the soak time that remains, after which, the AINS state moves to None.
Before you begin
Procedure
Run the
show controller command for the desired interface type and location.
Example:
This example shows the Ethernet controller statistics with AINS Soak in running state.
RP/0/RP0/CPU0:ios#show controller HundredGigECtrlr 0/1/0/2
Thu Feb 21 19:52:55.001 UTC
Operational data for interface HundredGigECtrlr0/1/0/2:
State:
Administrative state: enabled
Operational state: Up
LED state: Green On
Maintenance: Disabled
AINS Soak: Running
Total Duration: 0 hour(s) 15 minute(s)
Remaining Duration: 0 hour(s) 5 minute(s) 37 second(s)
Laser Squelch: Disabled
Phy:
Media type: Not known
Autonegotiation disabled.
Operational values:
Speed: 100Gbps
Duplex: Full Duplex
Flowcontrol: None
Loopback: None (or external)
BER monitoring:
Not supported
Holdoff Time: 0ms
Example:
This example shows the Ethernet controller statistics with AINS Soak in pending state.
RP/0/RP0/CPU0:ios#show controllers HuC 0/0/0/2
Thu Mar 12 13:52:12.129 UTC
Operational data for interface HundredGigECtrlr0/0/0/2:
State:
Administrative state: enabled
Operational state: Down (Reason: State undefined)
LED state: Red On
Maintenance: Disabled
AINS Soak: Pending
Total Duration: 0 hour(s) 30 minute(s)
Remaining Duration: 0 hour(s) 30 minute(s) 0 second(s)
Laser Squelch: Disabled
Phy:
Media type: Not known
Alarms:
Current:
Local Fault
Statistics:
FEC:
Corrected Codeword Count: 0
Uncorrected Codeword Count: 9
Autonegotiation disabled.
Operational values:
Speed: 100Gbps
Duplex: Full Duplex
Flowcontrol: None
Loopback: None (or external)
BER monitoring:
Not supported
Forward error correction: Standard (Reed-Solomon)
Holdoff Time: 0ms
Example:
This example shows the optics controller statistics with AINS Soak in running state.
RP/0/RP0/CPU0:ios#show controller optics 0/1/0/3
Thu Feb 21 19:45:41.088 UTC
Controller State: Up
Transport Admin State: Automatic In Service
Laser State: On
LED State: Green
Optics Status
Optics Type: 400G QSFP-DD DR4
Alarm Status:
-------------
Detected Alarms: None
LOS/LOL/Fault Status:
Alarm Statistics:
-------------
HIGH-RX-PWR = 0 LOW-RX-PWR = 0
HIGH-TX-PWR = 0 LOW-TX-PWR = 0
HIGH-LBC = 0 HIGH-DGD = 0
OOR-CD = 0 OSNR = 0
WVL-OOL = 0 MEA = 0
IMPROPER-REM = 0
TX-POWER-PROV-MISMATCH = 0
Performance Monitoring: Enable
THRESHOLD VALUES
----------------
Parameter High Alarm Low Alarm High Warning Low Warning
------------------------ ---------- --------- ------------ -----------
Rx Power Threshold(dBm) 4.9 -12.0 0.0 0.0
Tx Power Threshold(dBm) 3.5 -10.1 0.0 0.0
LBC Threshold(mA) N/A N/A 0.00 0.00
LBC High Threshold = 98 %
Polarization parameters not supported by optics
Total TX Power = 6.39 dBm
Total RX Power = 5.85 dBm
Lane Laser Bias TX Power RX Power Output Frequency
---- ---------- ---------- ---------- ----------------
1 75.0 % 0.59 dBm 0.63 dBm 230.43 THz
2 68.6 % 0.06 dBm -0.68 dBm 230.43 THz
3 69.0 % 0.26 dBm -0.63 dBm 230.43 THz
4 69.1 % 0.56 dBm -0.10 dBm 230.43 THz
Transceiver Vendor Details
Form Factor : QSFP-DD
Name : INNOLIGHT
Part Number : T-DP4CNT-NGL
Rev Number : 1A
Serial Number : INLBFI940027
PID : T-DP4CNT-NGL
VID : 1A
Date Code(yy/mm/dd) : 21/08/21
Fiber Connector Type: MPO
Otn Application Code: Not Set
Sonet Application Code: Not Set
Ethernet Compliance Code: 400GBASE-DR4
Transceiver Temperature : 32 Celsius
AINS Soak : Running
AINS Timer : 0h, 15m
AINS remaining time : 771 seconds
When the soak time expires, AINS state changes from Running to None. The Transport Admin State of optics controller changes from Automatic In Service to In Service.
RP/0/RP0/CPU0:ios# show controllers optics 0/1/0/3
Thu Feb 21 20:02:34.126 UTC
Controller State: Up
Transport Admin State: In Service
Laser State: On
LED State: Green
Optics Status
Optics Type: Grey optics
Alarm Status:
-------------
Detected Alarms: None
LOS/LOL/Fault Status:
Alarm Statistics:
-------------
HIGH-RX-PWR = 0 LOW-RX-PWR = 0
HIGH-TX-PWR = 0 LOW-TX-PWR = 0
HIGH-LBC = 0 HIGH-DGD = 0
OOR-CD = 0 OSNR = 0
WVL-OOL = 0 MEA = 0
IMPROPER-REM = 0
TX-POWER-PROV-MISMATCH = 0
Performance Monitoring: Enable
THRESHOLD VALUES
----------------
Parameter High Alarm Low Alarm High Warning Low Warning
------------------------ ---------- --------- ------------ -----------
Rx Power Threshold(dBm) 4.9 -12.0 0.0 0.0
Tx Power Threshold(dBm) 3.5 -10.1 0.0 0.0
LBC Threshold(mA) N/A N/A 0.00 0.00
LBC High Threshold = 98 %
Polarization parameters not supported by optics
Total TX Power = 6.41 dBm
Total RX Power = 5.85 dBm
Lane Laser Bias TX Power RX Power Output Frequency
---- ---------- ---------- ---------- ----------------
1 74.9 % 0.60 dBm 0.63 dBm 230.43 THz
2 68.6 % 0.06 dBm -0.70 dBm 230.43 THz
3 69.0 % 0.30 dBm -0.63 dBm 230.43 THz
4 69.1 % 0.57 dBm -0.11 dBm 230.43 THz
Transceiver Vendor Details
Form Factor : QSFP28
Name : CISCO-FINISAR
Part Number : FTLC1152RGPL-C2
Rev Number : CISCO-FINISAR
Serial Number : FNS22150LEC
PID : QSFP-100G-CWDM4-S
VID : V02
CISCO-FINISAR
Date Code(yy/mm/dd) : 18/04/11
Fiber Connector Type: LC
Sonet Application Code: Not Set
Ethernet Compliance Code: 100GBASE-CWDM4
Transceiver Temperature : 32 Celsius
AINS Soak : None
AINS Timer : 0h, 0m
AINS remaining time : 0 seconds
This example displays the coherentDSP controller statistics with AINS Soak in running state for a 2.4TX card.
RP/0/RP0/CPU0:ios#show controllers coherentDSP 0/0/0/7
Port : CoherentDSP 0/0/0/7
Controller State : Up
Inherited Secondary State : Automatic-In-Service
Configured Secondary State : Normal
Derived State : Automatic-In-Service
Loopback mode : None
BER Thresholds : SF = 1.0E-5 SD = 1.0E-7
Performance Monitoring : Enable
Bandwidth : 800.0Gb/s
Alarm Information:
LOS = 0 LOF = 0 LOM = 0
OOF = 0 OOM = 0 AIS = 0
IAE = 0 BIAE = 0 SF_BER = 0
SD_BER = 0 BDI = 0 TIM = 1
FECMISMATCH = 0 FEC-UNC = 0 FLEXO_GIDM = 1
FLEXO-MM = 0 FLEXO-LOM = 0 FLEXO-RDI = 1
FLEXO-LOF = 1
Detected Alarms : None
Bit Error Rate Information
PREFEC BER : 2.95E-04
POSTFEC BER : 0.00E+00
Q-Factor : 10.70 dB
Q-Margin : 4.40 dB
Instantaneous Q-Margin : 4.40 dB
TTI :
Remote hostname : chassisA164
Remote interface : CoherentDSP 0/1/0/7
Remote IP addr : 0.0.0.0
FEC mode : Soft-Decision 15
Flexo-Mode : Enable
Flexo Details:
Tx GID : 1
TX IID : 1, 2, 3, 4, 5, 6, 7, 8,
Rx GID : 1
RX IID : 1, 2, 3, 4, 5, 6, 7, 8,
AINS Soak : Running
AINS Timer : 0h, 20m
AINS remaining time : 1196 seconds