CCMD-16 controllers | Configuring Controllers | Configuration Guide for Cisco NCS 1014, IOS XR Releases 26.x.x

This section describes the types, automatic creation, and viewing commands for CCMD-16 controllers on NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards.

The NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards have two types of controllers.

OCH controllers
OMS controllers

When the NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards become operational, both the OMS and OCH controllers are automatically created by default.

View OCH controller and parameters

Use this task to view an OCH contollers and parameters.

When you bring up the nodes with NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards, the OCH controllers are automatically created by default. The OCH controllers for the NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards are:

Table 1. Supported interfaces
Card	Port type	OCH ports	Interfaces
NCS1K14-CCMD-16-C	LC Ports	16	och R/S/I/1 to och R/S/I/16
NCS1K14-CCMD-16-L	LC Ports	16	och R/S/I/1 to och R/S/I/16

Note

R/S/I/P stands for Rack/Slot/Instance/Port.

Procedure

Run the show controllers och command to view the OCH controllers.

Example:

This output shows the active OCH controllers in Slot 0 from port 1 to 16.

Output Example


0/0/0/1               Och Interface Instance
  0/0/0/10              Och Interface Instance
  0/0/0/11              Och Interface Instance
  0/0/0/12              Och Interface Instance
  0/0/0/13              Och Interface Instance
  0/0/0/14              Och Interface Instance
  0/0/0/15              Och Interface Instance
  0/0/0/16              Och Interface Instance
  0/0/0/2               Och Interface Instance
  0/0/0/3               Och Interface Instance
  0/0/0/4               Och Interface Instance
  0/0/0/5               Och Interface Instance
  0/0/0/6               Och Interface Instance
  0/0/0/7               Och Interface Instance
  0/0/0/8               Och Interface Instance
  0/0/0/9               Och Interface Instance

Run the show controllers command to view the parameters of an OCH controller.

Example:

This output shows the parameters of the OCH controller.

Output Example


RP/0/RP0/CPU0:ios#show controllers och 0/1/0/1
Thu Oct 12 09:26:38.555 UTC

 Controller State: Up 

 Transport Admin State: In Service 

 LED State: Green 

         Alarm Status:
         -------------
         Detected Alarms: None


         Alarm Statistics:
         -----------------
         RX-LOS-P = 0          
         TX-POWER-FAIL-LOW = 0 

         Parameter Statistics:
         ---------------------
         Tx Power = -2.30 dBm 
         Rx Power = -0.70 dBm

View OMS controller and parameters

Use this task to view an OMS controller and parameters.

When you bring up the nodes with NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards, the OMS controllers are automatically created by default.

The OMS controllers for the NCS1K14-CCMD-16-C and NCS1K14-CCMD-16-L cards are:

Table 2. Supported interfaces
Card	Port type	OMS ports	Interfaces
NCS1K14-CCMD-16-C	LC Ports	1	oms R/S/I/0
NCS1K14-CCMD-16-L	LC Ports	1	oms R/S/I/0

Note

R/S/I/P stands for Rack/Slot/Instance/Port.

Procedure

Run the show controllers oms ? command to view the OMS controllers.

Example:

This output shows the active OMS controller in Slot 0.

Run the show controllers command to view the parameters of an OMS controller.

Example:

This output shows the parameters of the an OMS controller.

Output Example


RP/0/RP0/CPU0:ios#show controllers oms 0/1/0/0
Thu Oct 12 09:23:35.297 UTC
 Controller State: Up 
 Transport Admin State: In Service 
 LED State: Red 
         Alarm Status:
         -------------
         Detected Alarms: 
                 HI-TX-BR-PWR    

         Alarm Statistics:
         -----------------
         RX-LOS-P = 3          
         TX-POWER-FAIL-LOW = 0          
         INGRESS-AMPLI-GAIN-LOW = 0          
         INGRESS-AMPLI-GAIN-HIGH = 0          
         EGRESS-AUTO-LASER-SHUT = 0          
         EGRESS-AMPLI-GAIN-LOW = 0          
         EGRESS-AMPLI-GAIN-HIGH = 0          
         HI-TX-BR-PWR = 2          
          
          
         Parameter Statistics:
         ---------------------
         Tx Power = -3.40 dBm 
         Rx Power = -2.30 dBm 
         Rx Voa Attenuation = 5.0 dB 
         Tx Voa Attenuation = 5.0 dB 
         Ingress Ampli Mode = Gain
         Ingress Ampli Gain = 5.0 dB
         Ingress Ampli Tilt = 0.0 dB
         Ingress Ampli OSRI = OFF 
         Egress Ampli Mode = Gain
         Egress Ampli Gain = 2.0 dB
         Egress Ampli Tilt = 0.0 dB
         Egress Ampli Gain Range = Normal 
         Egress Ampli OSRI = OFF 
         Egress Ampli BR Power = -12.90 dBm 
         Egress Ampli BR Ratio = -9.39 dB 
          
          
         Configured Parameters:
         -------------
         Rx Voa Attenuation = 5.0 dB 
         Tx Voa Attenuation = 5.0 dB 
         Ingress Ampli Mode = Gain
         Ingress Ampli Gain = 5.0 dB 
         Ingress Ampli Power = -9.0 dBm
         Ingress Ampli OSRI = OFF 
         Egress Ampli Mode = Gain
         Egress Ampli Gain = 2.0 dB 
         Egress Ampli Power = 0.0 dBm
         Egress Ampli Gain Range = Normal 
         Egress Ampli OSRI = OFF 
         BR High Threshold = -17.0 dBm