Secure Connections Overview

A virtual private network (VPN) connection establishes a secure tunnel between endpoints over a public network such as the Internet.

This chapter applies to Remote Access and Site-to-site VPNs on Secure Firewall Threat Defense devices. It describes the Internet Protocol Security (IPsec), the Internet Security Association and Key Management Protocol (ISAKMP, or IKE) and SSL standards that are used to build site-to-site and remote access VPNs.

VPN types

VPN types are network connection categories that

  • provide secure, encrypted connections between remote locations and private networks

  • support deployment models including remote access and site-to-site configurations, and

  • use various protocols including SSL and IPsec for establishing secure tunnels.

Supported VPN connection types

The Firewall Management Center supports these types of VPN connections:

  • Remote Access VPNs in Firewall Threat Defense devices.

    Remote access VPNs provide secure, encrypted connections, or tunnels, between remote users and your company's private network. These connection use two devices: a VPN endpoint device, which is a workstation or mobile device with VPN client capabilities, and a VPN headend device, or secure gateway, at the edge of the corporate private network.

    Secure Firewall Threat Defense devices can be configured to support Remote Access VPNs over SSL or IPsec IKEv2 by the Firewall Management Center. When acting as secure gateways, these devices authenticate remote users, authorize access, and encrypt data to provide secure connections to your network. Only these devices support remote access VPN connections, managed by the Firewall Management Center.

    Secure Firewall Threat Defense secure gateways support the Secure Client full tunnel client. This client is required to provide secure SSL IPsec IKEv2 connections for remote users. This client automatically installs when a connection is established, so network administrators do not need to manually install or configure it on remote computers. It is the only client supported on endpoint devices.

  • Site-to-site VPNs in Firewall Threat Defense devices.

    A site-to-site VPN connects networks in different geographic locations. You can create site-to-site IPsec connections between managed devices, and between managed devices and other Cisco or third-party peers. These peers can use either IPv4 and IPv6 addresses. Site-to-site tunnels are built using the Internet Protocol Security (IPsec) protocol suite and IKEv1 or IKEv2. After the VPN connection is established, the hosts behind the local gateway can connect to the hosts behind the remote gateway through the secure VPN tunnel.

VPN basics

A VPN is a secure networking technology that

  • uses tunneling to create secure connections between remote users and private corporate networks over public TCP/IP networks such as the Internet

  • employs IPsec-based technologies with ISAKMP (IKE) and IPsec tunneling standards to build and manage tunnels, and

  • enables bidirectional data transfer through tunnel endpoints that encapsulate and unencapsulate packets.

VPN tunnel management capabilities

ISAKMP and IPsec accomplish these tunnel management functions:

  • Negotiate tunnel parameters.

  • Establish tunnels.

  • Authenticate users and data.

  • Manage security keys.

  • Encrypt and decrypt data.

  • Manage data transfer across the tunnel.

  • Manage data transfer inbound and outbound as a tunnel endpoint or router.

A device in a VPN functions as a bidirectional tunnel endpoint. It can receive plain packets from the private network, encapsulate them, create a tunnel, and send them to the other end of the tunnel where they are unencapsulated and sent to their final destination. It can also receive encapsulated packets from the public network, unencapsulate them, and send them to their final destination on the private network.

After the site-to-site VPN connection is established, the hosts behind the local gateway can connect to the hosts behind the remote gateway through the secure VPN tunnel. A connection consists of the IP addresses and hostnames of the two gateways, the subnets behind them, and the method the two gateways use to authenticate to each other.

VPN deployments use two primary device types:

  • Hubs: Devices that enable secure VPN connectivity to and from one or more remote branch devices or spokes. Hubs also act as a gateway for spokes to communicate with each other.

  • Spokes: Devices that connect over VPN to a hub to securely access the corporate resources behind the hub. Spokes communicate with each other through the hub.

Internet Key Exchange (IKE)

Internet Key Exchange (IKE) is a key management protocol that

  • authenticates IPsec peers

  • negotiates and distributes IPsec encryption keys, and

  • automatically establishes IPsec security associations (SAs).

IKE negotiation phases and policies

The IKE negotiation comprises two phases:

  • Phase 1 negotiates a security association between two IKE peers, which enables the peers to communicate securely in Phase 2.

  • During Phase 2 negotiation, IKE establishes SAs for other applications, such as IPsec.

Each phase uses proposals to negotiate a connection.

An IKE policy is a set of algorithms that two peers use to secure the IKE negotiation between them. IKE negotiation begins when each peer agrees on a common IKE policy. This policy defines security parameters to protect subsequent IKE negotiations. IKEv1 policies contain a single set of algorithms and a modulus group. In an IKEv2 policy, you can select multiple algorithms and modulus groups for peers to choose from during the Phase 1 negotiation. You may create a single IKE policy, or create multiple policies to give higher priority to preferred options. For site-to-site VPNs, you can create an IKE policy. IKEv1 and IKEv2 each support a maximum of 20 IKE policies, each with a different set of values. Assign a unique priority to each policy that you create. A lower priority number indocates a higher priority for the policy.

To define an IKE policy, specify:

  • A unique priority (1 to 65,543, with 1 being the highest priority).

  • An encryption method for the IKE negotiation to protect the data and ensure privacy.

  • A Hashed Message Authentication Codes (HMAC) method (called integrity algorithm in IKEv2) to verify the sender's identity, and to confirm that the message is unchanged during transit.

  • For IKEv2, a separate pseudorandom function (PRF) used as the algorithm to derive keying material and hashing operations required for the IKEv2 tunnel encryption. The options are the same as those used for the hash algorithm.

  • A Diffie-Hellman group to determine the strength of the encryption key determination algorithm. The device uses this algorithm to derive the encryption and hash keys.

  • An authentication method, to ensure the identity of the peers.

  • A limit to the time the device uses an encryption key before replacing it.

When IKE negotiation begins, the initiating peer sends all its policies to the remote peer. The remote peer searches for a match with its own policies, in priority order. IKE policies match if both peers use the same encryption, hash (integrity and PRF for IKEv2), authentication, and Diffie-Hellman values. The SA lifetime must be less than or equal to the lifetime in the policy sent. If the lifetimes are not identical, the shorter value from the remote peer policy applies. By default, the Secure Firewall Management Center deploys an IKEv1 policy with the lowest priority for all VPN endpoints to ensure a successful negotiation.

IPsec

IPsec is a secure method for setting up a VPN that:

  • provides data encryption at the IP packet level,

  • transmits data over a public network through tunnels, which are secure, logical communication paths between two peers, and

  • secures traffic that enters an IPsec tunnel by a combination of security protocols and algorithms.

With IPsec, data is transmitted over a public network through tunnels.

IPsec proposal policy components

An IPsec proposal policy defines the settings for IPsec tunnels. An IPsec proposal includes one or more crypto maps that are applied to the VPN interfaces in the devices. A crypto map combines all the components required to set up IPsec security associations, including:

  • A proposal (or transform set) combines security protocols and algorithms that secure traffic in an IPsec tunnel. During the IPsec security association (SA) negotiation, peers search for a matching proposal. Apply the selected proposal to create an SA that protects data flows in the crypto map's access list and secures VPN traffic. There are separate IPsec proposals for IKEv1 and IKEv2. In IKEv1 proposals (or transform sets), you set one value for each parameter. In IKEv2 proposals, you can configure multiple encryption and integration algorithms for a single proposal.

  • A crypto map combines all components required to set up IPsec security associations (SA), including IPsec rules, proposals, remote peers, and other parameters that are necessary to define an IPsec SA. When two peers try to establish an SA, they must each have at least one compatible crypto map entry.

    Dynamic crypto map policies are used in site-to-site VPNs when an unknown remote peer tries to start an IPsec security association with the local hub. The hub does not initiate the security association negotiation. Dynamic crypto policies allow remote peers to exchange IPsec traffic with a local hub, even if the hub does not know the remote peer's identity. A dynamic crypto map policy creates a crypto map entry before configuring all parameters. IPsec negotiation then dynamically configures the missing parameters to match a remote peer's requirements.

    Dynamic crypto map policies are applicable to both hub-and-spoke and point-to-point VPN topologies. To apply dynamic crypto map policies, specify a dynamic IP address for one of the peers in the topology and ensure that the dynamic crypto-map is enabled on this topology. In a full mesh VPN topology, you can apply only static crypto map policies.


    Note

    Simultaneous IKEv2 dynamic crypto map is not supported for the same interface for both remote access and site-to-site VPNs in a Firewall Threat Defense device.

VPN packet flow

VPN packet flow is a security process that

  • requires explicit permission through access control before allowing traffic to pass through,

  • decrypts incoming tunnel packets before sending them to the Snort process,

  • processes outgoing packets through Snort before encryption, and

  • blocks tunnel traffic to the public source when the tunnel is down.

Access control requirements

Access control identifies the protected networks for each endpoint node of a VPN tunnel and determines which traffic is allowed to pass through the Firewall Threat Defense device and reach the endpoints. For remote access VPN traffic, a group policy filter or an access control rule must be configured to permit VPN traffic flow.

IPsec flow offload

IPsec flow offload is a performance optimization feature that

  • offloads IPsec connections to field-programmable gate array (FPGA) or specialized hardware components after initial setup

  • improves device performance by handling pre-decryption, decryption, pre-encryption, and encryption processing in hardware, and

  • is enabled by default on supporting device models while allowing system software to handle inner flow security policies.

IPsec flow offload characteristics

After the initial setup of an IPsec site-to-site VPN or remote access VPN security association (SA), IPsec connections are offloaded to the field-programmable gate array (FPGA) in the device, which should improve device performance. On the Secure Firewall 1200 series, IPsec connections are offloaded to the Marvell Cryptographic Accelerator (CPT) to improve device performance.On the Secure Firewall 6100 series, IPsec connections are offloaded to the Kintex 7 (KC400) FPGA. This FPGA contains a built-in crypto engine that is capable of handling AES-GCM-128 and AES-GCM-256 encryption and decryption.

Offloaded operations specifically relate to the pre-decryption and decryption processing on ingress, and the pre-encryption and encryption processing on egress. The system software handles the inner flow to apply your security policies.

IPsec flow offload applies to these device types:

  • Secure Firewall 1200

  • Secure Firewall 3100

  • Secure Firewall 4200

  • Secure Firewall 6100

IPsec flow offload is also used when the device's VTI loopback interface is enabled.

For asymmetric flows in cluster distributed site-to-site VPN mode, IPsec flow offload now lets the flow owner decrypt IPsec traffic in hardware that was forwarded over the cluster control link. This feature is not configurable and is always available with IPsec flow offload.

IPsec flows that are not offloaded include:

  • IKEv1 tunnels. Only IKEv2 tunnels will be offloaded. IKEv2 supports stronger ciphers.

  • Flows that have volume-based rekeying configured.

  • Flows that have compression configured.

  • Transport mode flows. Only tunnel mode flows will be offloaded.

  • AH format. Only ESP/NAT-T format will be supported.

  • Flows that have post-fragmentation configured.

  • Flows that have anti-replay window size other than 64bit and anti-replay is not disabled.

  • Flows that have firewall filter enabled.

  • Mult-instance mode.

  • Secure Firewall 6100 supports AES-GCM-128 and AES-GCM-256 ciphers only. IPsec tunnels that are configured with other ciphers are not offloaded. Any IPsec packets that are not offloaded are processed by the software engine in the CPU.

IPsec flow offload is enabled by default on hardware platforms that support the feature. To change the configuration, use FlexConfig to implement the flow-offload-ipsec command. See the ASA command reference for detailed information about the command.

VPN licensing

There is no specific licensing for enabling Secure Firewall Threat Defense VPN, it is available by default.

The Firewall Management Center determines whether to allow or block the usage of strong crypto on the Firewall Threat Defense device based on attributes provided by the smart licensing server.

This is controlled by whether you selected the option to allow export-controlled functionality on the device when you registered with the Cisco Smart License Manager. If you are using the evaluation license, or you did not enable export-controlled functionality, you cannot use strong encryption.

If you have created your VPN configurations with an evaluation license, and upgrade your license from evaluation to smart license with export-controlled functionality, check, and update your encryption algorithms for stronger encryption and for the VPNs to work properly. DES-based encryptions are no longer supported.

How Secure Should a VPN Connection Be?

Find a balance between security and performance that provides sufficient protection without compromising efficiency when configuring VPN tunnel encryption.

Because a VPN tunnel typically traverses a public network, most likely the Internet, you need to encrypt the connection to protect the traffic. You define the encryption and other security techniques to apply using IKE polices and IPsec proposals. As a general rule, the stronger the encryption that you apply to the tunnel, the worse the system performance.

If your device license allows you to apply strong encryption, there is a wide range of encryption and hash algorithms, and Diffie-Hellman groups, from which to choose. We cannot provide specific guidance on which options to choose. If you operate within a larger corporation or other organization, there might already be defined standards that you need to meet. If not, take the time to research the options.

Recommendation: complying with security certification requirements

Review your certification requirements and the available options to plan your VPN configuration. Many VPN settings have options that allow you to comply with various security certification standards.

Decide encryption algorithms for VPN policies

When deciding which encryption algorithms to use for the IKE policy or IPsec proposal, your choice is limited to algorithms supported by the devices in the VPN.

  • For IKEv2, you can configure multiple encryption algorithms. The system orders the settings from the most secure to the least secure and negotiates with the peer using that order.

  • For IKEv1, you can select a single option only.

  • For IPsec proposals, the algorithm is used by the Encapsulating Security Protocol (ESP), which provides authentication, encryption, and anti-replay services. ESP is IP protocol type 50. In IKEv1 IPsec proposals, the algorithm name is prefixed with ESP-.

If your device license qualifies for strong encryption, you can choose from the available encryption algorithms. If you are not qualified for strong encryption, you can select DES only.

Strong encryption license considerations


Note

If you are qualified for strong encryption, before upgrading from the evaluation license to a smart license, check and update your encryption algorithms for stronger encryption so that the VPN configuration works properly. Choose AES-based algorithms. DES is not supported if you are registered using an account that supports strong encryption. After registration, you cannot deploy changes until you remove all uses of DES.

Available encryption algorithms

  • AES-GCM—(IKEv2 only.) Advanced Encryption Standard in Galois/Counter Mode is a block cipher mode of operation providing confidentiality and data-origin authentication, and provides greater security than AES. AES-GCM offers three different key strengths: 128-, 192-, and 256-bit keys. A longer key provides higher security but a reduction in performance. GCM is a mode of AES that is required to support NSA Suite B. NSA Suite B is a set of cryptographic algorithms that devices must support to meet federal standards for cryptographic strength.

  • AES—Advanced Encryption Standard is a symmetric cipher algorithm that provides greater security than DES and is computationally more efficient than 3DES. AES offers three different key strengths: 128-, 192-, and 256-bit keys. A longer key provides higher security but a reduction in performance.

  • DES—Data Encryption Standard, which encrypts using 56-bit keys, is a symmetric secret-key block algorithm. If your license account does not meet the requirements for export controls, this is your only option.

  • Null, ESP-Null—A null encryption algorithm provides authentication without encryption. This method is not secure; use at your own discretion.

Decide which hash algorithms to use

In IKE policies, the hash algorithm creates a message digest, which is used to ensure message integrity. In IKEv2, the hash algorithm is separated into two options, one for the integrity algorithm, and one for the pseudo-random function (PRF).

In IPsec proposals, the hash algorithm is used by the Encapsulating Security Protocol (ESP) for authentication. In IKEv2 IPsec Proposals, this is called the integrity hash. In IKEv1 IPsec proposals, the algorithm name is prefixed with ESP-, and there is also an -HMAC suffix (which stands for "hash method authentication code").

For IKEv2, you can configure multiple hash algorithms. The system orders the settings from the most secure to the least secure and negotiates with the peer using that order. For IKEv1, you can select a single option only.

Select from these hash algorithms based on your security and performance requirements:

  • SHA (Secure Hash Algorithm)—Standard SHA (SHA1) produces a 160-bit digest.

    The following SHA-2 options, which are even more secure, are available for IKEv2 configurations. Choose one of these if you want to implement the NSA Suite B cryptography specification.

    • SHA256—Specifies the Secure Hash Algorithm SHA 2 with the 256-bit digest.

    • SHA384—Specifies the Secure Hash Algorithm SHA 2 with the 384-bit digest.

    • SHA512—Specifies the Secure Hash Algorithm SHA 2 with the 512-bit digest.

  • NULL or NONE (NULL, ESP-NONE)—(IPsec Proposals only.) A NULL Hash Algorithm; this is typically used for testing purposes only. However, you should choose the NULL integrity algorithm if you select one of the AES-GCM options as the encryption algorithm. Even if you choose a non-NULL option, the integrity hash is ignored for these encryption standards.

Decide which Diffie-Hellman modulus group to use

You can use Diffie-Hellman key derivation algorithms to generate IPsec security association (SA) keys. Each group has a different size modulus. A larger modulus provides higher security, but requires more processing time. You must have a matching modulus group on both peers.

If you select AES encryption, to support the large key sizes required by AES, you should use Diffie-Hellman (DH) Group 5 or higher. IKEv1 policies do not support all of the groups listed below.

To implement the NSA Suite B cryptography specification, use IKEv2 and select one of the elliptic curve Diffie-Hellman (ECDH) options: 19, 20, or 21. Elliptic curve options and groups that use 2048-bit modulus are less exposed to attacks such as Logjam.

For IKEv2, you can configure multiple groups. The system orders the settings from the most secure to the least secure and negotiates with the peer using that order. For IKEv1, you can select a single option only.

  • 14—Diffie-Hellman Group 14: 2048-bit modular exponential (MODP) group. Considered good protection for 192-bit keys.

  • 15—Diffie-Hellman Group 15: 3072-bit MODP group.

  • 16—Diffie-Hellman Group 16: 4096-bit MODP group.

  • 19—Diffie-Hellman Group 19: National Institute of Standards and Technology (NIST) 256-bit elliptic curve modulo a prime (ECP) group.

  • 20—Diffie-Hellman Group 20: NIST 384-bit ECP group.

  • 21—Diffie-Hellman Group 21: NIST 521-bit ECP group.

  • 31—Diffie-Hellman Group 31: Curve25519 256-bit EC Group.

Decide VPN authentication methods

A VPN authentication method is a security mechanism that

  • validates the identity of peers in a VPN connection

  • enables secure communication between network devices, and

  • ensures only authorized devices can establish VPN connections.

Available authentication methods

VPNs support two primary authentication methods:

  • Preshared keys: A secret key shared between two peers and used by IKE during the authentication phase. The same shared key must be configured at each peer or the IKE SA cannot be established.

  • Digital certificates: Use RSA key pairs to sign and encrypt IKE key management messages. Certificates provide non-repudiation of communication between two peers, meaning that it can be proved that the communication actually took place.

VPN type support varies by authentication method:

Table 1. VPN authentication method support

VPN Type

Preshared Keys

Digital Certificates

Site-to-site IKEv1 and IKEv2

Supported

Supported

Remote Access (SSL and IPsec IKEv2)

Not supported

Supported

When using digital certificate authentication, you need a Public Key Infrastructure (PKI) defined where peers can obtain digital certificates from a Certification Authority (CA). CAs manage certificate requests and issue certificates to participating network devices providing centralized key management for all of the participating devices.

Preshared keys do not scale well, using a CA improves the manageability and scalability of your IPsec network. With a CA, you do not need to configure keys between all encrypting devices. Instead, each participating device is registered with the CA, and requests a certificate from the CA. Each device that has its own certificate and the public key of the CA can authenticate every other device within a given CA's domain.

Pre-shared keys

A pre-shared key is a secret key that

  • enables you to share authentication credentials between two peers

  • is used by IKE in the authentication phase, and

  • must be configured identically on each peer or the IKE SA cannot be established.

Key configuration options

To configure the pre-shared keys, choose whether you want to use a manual or automatically generated key, and then specify the key in the IKEv1/IKEv2 options. Then, when you deploy your configuration, the key is configured on all devices in the topology.

PKI infrastructure and digital certificates

A PKI infrastructure is a centralized key management system that

  • provides defined policies, procedures, and roles supporting public key cryptography

  • generates, verifies, and revokes public key certificates commonly known as digital certificates, and

  • manages key pairs consisting of public and private keys for VPN endpoints to sign and encrypt messages.

Public key cryptography and certificate components

In public key cryptography, each endpoint of a connection has a key pair consisting of both a public and a private key. The key pairs are used by the VPN endpoints to sign and encrypt messages. The keys act as complements, and anything encrypted with one of the keys can be decrypted with the other, securing the data flowing over the connection.

Generate a general purpose RSA, ECDSA, or EDDSA key pair, used for both signing and encryption, or you generate separate key pairs for each purpose. Separate signing and encryption keys help to reduce exposure of the keys. SSL uses a key for encryption but not signing, however, IKE uses a key for signing but not encryption. By using separate keys for each, exposure of the keys is minimized.

Certificates also provide non-repudiation of communication between two peers, meaning that it they prove that the communication actually took place.

CA certificates may be obtained by:

  • Using the Simple Certificate Enrollment Protocol (SCEP) or Enrollment over Secure Transport (EST) to retrieve the CA's certificate from the CA server

  • Manually copying the CA's certificate from another participating device

Trustpoints represent the object representation of a CA and associated certificates. A trustpoint includes the identity of the CA, CA-specific parameters, and an association with a single enrolled identity certificate.

A PKCS#12, or PFX, file holds the server certificate, any intermediate certificates, and the private key in one encrypted file. This type of file may be imported directly into a device to create a trustpoint.

A CA may also revoke certificates for peers that no longer participate in you network. Revoked certificates are either managed by an Online Certificate Status Protocol (OCSP) server or are listed in a certificate revocation list (CRL) stored on an LDAP server. A peer may check these before accepting a certificate from another peer.

Digital certificates or identify certificates

When you use digital certificates as the authentication method for VPN connections, peers are configured to obtain digital certificates from a Certificate Authority (CA). CAs are trusted authorities that sign certificates to verify their authenticity, thereby guaranteeing the identity of the device or user.

Digital certificates contain these components:

  • The digital identification of the owner for authentication, such as name, serial number, company, department, or IP address.

  • A public key needed to send and receive encrypted data to the certificate owner.

  • The secure digital signature of a CA.

Certificate enrollment process involves:

  1. CA servers manage public CA certificate requests and issue certificates to participating network devices as part of a PKI.

  2. Each participating device enrolls individually with a CA server, which validates identities and creates an identity certificate.

  3. Each participating peer sends their identity certificate to the other peer to validate their identities and establish encrypted sessions with the public keys contained in the certificates.

Certificate Enrollment

Using a PKI improves the manageability and scalability of your VPN since you do not have to configure pre-shared keys between all the encrypting devices. Instead, you individually enroll each participating device with a CA server, which is explicitly trusted to validate identities and create an identity certificate for the device. When this has been accomplished, each participating peer sends their identity certificate to the other peer to validate their identities and establish encrypted sessions with the public keys contained in the certificates. See Certificate Enrollment Objects for details on enrolling Firewall Threat Defense devices.

Certificate Authority Certificates

In order to validate a peer’s certificate, each participating device must retrieve the CA's certificate from the server. A CA certificate is used to sign other certificates. It is self-signed and called a root certificate. This certificate contains the public key of the CA, used to decrypt and validate the CA's digital signature and the contents of the received peer's certificate. The CA certificate may be obtained by:

  • Using the Simple Certificate Enrollment Protocol (SCEP) or Enrollment over Secure Transport (EST) to retrieve the CA’s certificate from the CA server

  • Manually copying the CA's certificate from another participating device

Trustpoints

Once enrollment is complete, a trustpoint is created on the managed device. It is the object representation of a CA and associated certificates. A trustpoint includes the identity of the CA, CA-specific parameters, and an association with a single enrolled identity certificate.

PKCS#12 File

A PKCS#12, or PFX, file holds the server certificate, any intermediate certificates, and the private key in one encrypted file. This type of file may be imported directly into a device to create a trustpoint.

Revocation Checking

A CA may also revoke certificates for peers that no longer participate in you network. Revoked certificates are either managed by an Online Certificate Status Protocol (OCSP) server or are listed in a certificate revocation list (CRL) stored on an LDAP server. A peer may check these before accepting a certificate from another peer.

Removed or deprecated hash algorithms, encryption algorithms, and Diffie-Hellman modulus groups

Update your VPN configuration before you upgrade to Firewall Threat Defense 6.70 to supported DH and encryption algorithms to ensure the VPN works correctly.

  • Update your IKE proposals and IPSec policies to match the ones supported in Firewall Threat Defense 6.70.

  • Deploy the configuration changes after updating to supported algorithms.

Support has been removed for less secure ciphers. These less secure ciphers have been removed or deprecated from Firewall Threat Defense Version 6.70 onwards:

  • Diffie-Hellman GROUP 5 is deprecated for IKEv1 and IKEv2.

  • Diffie-Hellman groups 2 and 24 have been removed.

  • Encryption algorithms: 3DES, AES-GMAC, AES-GMAC-192, AES-GMAC-256 have been removed.


    Note

    DES continues to be supported in evaluation mode or for users who do not satisfy export controls for strong encryption.

    NULL is removed in IKEv2 policy, but supported in both IKEv1 and IKEv2 IPsec transform-sets.

VPN topology options

When you create a new VPN topology you must, at minimum, give it a unique name, specify a topology type, and select the IKE version. You can select from three types of topologies, each containing a group of VPN tunnels:

  • Point-to-point (PTP) topologies establish a VPN tunnel between two endpoints.

  • Hub and Spoke topologies establish a group of VPN tunnels connecting a hub endpoint to a group of spoke endpoints.

  • Full Mesh topologies establish a group of VPN tunnels among a set of endpoints.

Define a pre-shared key for VPN authentication manually or automatically, there is no default key. When choosing automatic, the Secure Firewall Management Center generates a pre-shared key and assigns it to all the nodes in the topology.

Point-to-point VPN topologies

A point-to-point VPN topology is a network configuration that

  • enables two endpoints to communicate directly with each other

  • allows you to configure the two endpoints as peer devices, and

  • permits either device to start the secured connection.

Point-to-point VPN topology diagram

This diagram displays a typical point-to-point VPN topology.

Diagram illustrating a point-to-point VPN topology

Hub and spoke VPN topology

A hub and spoke VPN topology is a network architecture that

  • connects a central endpoint (hub node) with multiple remote endpoints (spoke nodes)

  • establishes each connection between the hub node and an individual spoke endpoint as a separate VPN tunnel, and

  • enables hosts behind any of the spoke nodes to communicate with each other through the hub node.

The hub and spoke topology commonly represent a VPN that connects an organization's main and branch office locations using secure connections over the Internet or other third-party network. These deployments provide all employees with controlled access to the organization's network. Typically, the hub node is located at the main office. Spoke nodes are located at branch offices and start most of the traffic.

This diagram displays a typical hub and spoke VPN topology.

Figure 1. Hub and spoke VPN topology diagram
Diagram illustrating a Hub and Spoke VPN topology

Full mesh VPN topology

A full mesh VPN topology is a network configuration that

  • allows all endpoints to communicate with every other endpoint by an individual VPN tunnel

  • offers redundancy so that when one endpoint fails, the remaining endpoints can still communicate with each other, and

  • commonly represents a VPN that connects a group of decentralized branch office locations.

The number of VPN-enabled managed devices you deploy in this configuration depends on the level of redundancy you require.

This diagram displays a typical full mesh VPN topology.

Figure 2. Full mesh VPN topology diagram
Diagram illustrating mesh VPN topology

Implicit topologies

Implicit topologies are complex VPN network configurations that

  • combine elements from the three main VPN topologies (full mesh, hub-and-spoke, and point-to-point)

  • create more sophisticated network architectures than individual topology types, and

  • provide customized connectivity solutions for specific network requirements.

Types of implicit topologies

  • Partial mesh: A network in which some devices are organized in a full mesh topology, and other devices form either a hub-and-spoke or a point-to-point connection to some of the fully meshed devices. A partial mesh does not provide the level of redundancy of a full mesh topology, but it is less expensive to implement. Partial mesh topologies are used in peripheral networks that connect to a fully meshed backbone.

  • Tiered hub-and-spoke: A network of hub-and-spoke topologies in which a device can behave as a hub in one or more topologies and a spoke in other topologies. Traffic is permitted from spoke groups to their most immediate hub.

  • Joined hub-and-spoke: A combination of two topologies (hub-and-spoke, point-to-point, or full mesh) that connect to form a point-to-point tunnel. For example, a joined hub-and-spoke topology could comprise two hub-and-spoke topologies, with the hubs acting as peer devices in a point-to-point topology.