IPv6 non-AVC QoS support enables Quality of Service (QoS) for IPv6 traffic on Fabric and FlexConnect local switching and offers the same functionality as IPv4 QoS starting from Cisco IOS XE 17.2.1.

IPv6 non-AVC QoS support is a wireless network feature that

enables QoS for IPv6 traffic on Fabric and FlexConnect local switching,
performs QoS processing at the access point (AP), and
offers the same functionality as IPv4 QoS starting from Cisco IOS XE 17.2.1.

Supported actions for IPv6 non-AVC QoS

You can use IPv6 non-AVC QoS to:

mark the Differentiated Services Code Point (DSCP) value for IPv6 packets,
drop IPv6 packets based on the DSCP value,
police IPv6 traffic.

Platform limitations

IPv6 non-AVC QoS is not supported on Cisco Aironet 1700, 2700, or 3700 Series Access Points.

Mark DSCP values in an IPv6 packet (CLI)

Assign differentiated services code point (DSCP) values to IPv6 packets for traffic classification and Quality of Service (QoS).

Procedure

	1.	Enter global configuration mode. Example: `Device# configure terminal`
	2.	Create a policy map. Example: `Device(config)# policy-map policy-map-name`
	3.	Specify the class map criteria for the policy. Example: `Device(config-pmap)#class class-map-name`
	4.	Set the DSCP value in an IPv6 packet. Example: `Device(config-pmap-c)#set dscp <0-63>` DSCP values must be in the range of 0 to 63.

The selected DSCP value is assigned to matching IPv6 packets, enabling traffic classification and QoS handling according to your policy.

Drop an IPv6 packet with DSCP values (CLI)

Procedure

	1.	Enter global configuration mode. Example: `Device# configure terminal`
	2.	Create a policy map. Example: `Device(config)# policy-map policy-map-name`
	3.	Create a policy criteria. Example: `Device(config-pmap)#class class-map-name`
	4.	Police the committed information rate. Example: `Device(config-pmap-c)#police cir <8000 - 10000000000>` the committed information rate is between 8000 and 10000000000. Target bit rate (Bits per second).
	5.	Configure the conform-action drop command. Example: `Device(config-pmap-c-police)#conform action drop` This command is the action when the rate is less than the conform burst.
	6.	Configure the exceed-action drop command. Example: `Device(config-pmap-c-police)#exceed-action drop` This command is the action when the rate is within the conform and conform plus exceed burst.

Configure policing for IPv6 traffic (CLI)

Police IPv6 traffic by enforcing bandwidth limits and actions for conforming and exceeding packets.

Procedure

	1.	Enter global configuration mode. Example: `Device# configure terminal`
	2.	Create a policy map. Example: `Device(config)# policy-map policy-map-name`
	3.	Create a policy criteria. Example: `Device(config-pmap)#class class-map-name`
	4.	Specify the committed information rate. Example: `Device(config-pmap-c)#police cir <8000 - 10000000000>` The CIR (committed information rate) sets the allowed bits per second; choose a value between 8000 and 10,000,000,000.
	5.	Configure the conform-action transmit command, for transmitting packets. Example: `Device(config-pmap-c-police)#conform-action transmit`
	6.	Configure the exceed-action drop command. Example: `Device(config-pmap-c-police)#exceed-action drop` This command specifies the action taken when the packet rate exceeds the CIR but is within conform plus exceed burst.

IPv6 traffic is policed according to your defined bandwidth and actions. The device transmits packets within the CIR and drops packets that exceed the specified rate.

IPv6 non-AVC QoS verification

To verify the DSCP values for IPv6 packets, IPv6 packets that are dropped, and the policing of IPv6 traffic, use the show policy-map command:

This is a sample output of the show command that verifies the DSCP value for an IPv6 packet:
```
Device# show policy-map 
1 policymaps
Policy Map Set-dscp type:qos client:default
	Class Set-dscp1_ADV_UI_CLASS
	set dscp af41 (34)
	Class class-default
	no actions
```

This is a sample output of the show command that verifies the IPv6 packets that are dropped:

Device# show policy-map 
1 policymaps
Policy Map Drop-dscp type:qos client:default	
        Class Drop-dscp1_ADV_UI_CLASS	
        drop
	 
        Class class-default	
        no actions

This is a sample output of the show command that verifies the policing of IPv6 traffic:

Device# show policy-map 
1 policymaps
Policy Map Drop-traffic type:qos client:default	
        Class Drop-traffic1_ADV_UI_CLASS	
        police rate 2000000 bps (250000Bytes/s)	
        conform-action 	
        exceed-action
	
        Class class-default	
        no actions

Need help?

Open a support case

(Requires a Cisco Service Contract)

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

IPv6 non-AVC QoS support

Supported actions for IPv6 non-AVC QoS

Platform limitations

Mark DSCP values in an IPv6 packet (CLI)

Procedure

Example:

Example:

Example:

Example:

Drop an IPv6 packet with DSCP values (CLI)

Procedure

Example:

Example:

Example:

Example:

Example:

Example:

Configure policing for IPv6 traffic (CLI)

Procedure

Example:

Example:

Example:

Example:

Example:

Example:

IPv6 non-AVC QoS verification