This section contains information about the new and changed features for Cisco Unified Communications Manager, Release 11.0(1).

• Default CTI IP Addressing for Devices

• Ringback on SIP 183 for Transferred Calls

This section describes the features supported in previous releases and contains the following sections:

• Cisco Unified Communications Manager Release 10.5(2)

• Cisco Unified Communications Manager Release 10.0(1)

• Cisco Unified Communications Manager Release 9.0(1)

• Cisco Unified Communications Manager Release 8.6(1)

• Cisco Unified Communications Manager Release 8.5(1)

• Cisco Unified Communications Manager Release 8.0(1)

• Cisco Unified Communications Manager Release 7.1(3)

• Cisco Unified Communications Manager Release 7.1(2)

• Cisco Unified Communications Manager Release 7.0(1)

• Cisco Unified Communications Manager Release 6.1

• Cisco Unified Communications Manager Release 6.0

• Cisco Unified Communications Manager Release 5.1

• Cisco Unified Communications Manager Release 5.0

This section describes the new and changed features in Cisco Unified Communications Manager release 9.0(1):

• Cius Persistency

• CTI Remote Device for JTAPI

• E911 Teleworker

• Hunt List Connected Number

• Native Queuing

• URI Dialing

This section describes the new and changed features in Cisco Unified Communications Manager release 8.6(1):

• Account Lockout

• EnergyWise Deep Sleep Mode

• FIPS Compliance

• Password Expiry

• New JTAPI x64 client for 64-bit operating systems.

This section describes the new and changed features in Cisco Unified Communications Manager release 8.5(1):

• Agent Greeting

• API for Exposing Built-In-Bridge Status

• Play Zip Tone

• Single Sign-On

• Support for VMware

This section describes the new and changed features in Cisco Unified Communications Manager release 8.0(1):

• Call Control Discovery

• Call Pickup

• CallFwdAll Key Press Notification

• End to End Call Tracing

• Extension Mobility Cross Cluster

• External Call Control

• Hunt List

• iSac Codec

• Secured Monitoring and Recording

• Support for Cisco Unified IP Phone 6901

• Support for 100+ Directory Numbers

• Support for VMware

• Verification Involving PSTN Reachability

This section describes the new and changed features in Cisco Unified Communications Manager release 7.1(3):

• Terminal and Address Capability Settings.

This section describes the new and changed features in Cisco Unified Communications Manager release 7.1(2):

• Component Updater

• Direct Transfer Across Lines

• Drop Any Party

• IPv6 Support

• Join Across Lines or Connected Conference Across Lines

• Logical Partitioning

• Message Waiting Indicator Enhancement

• Park Monitoring and Assisted DPark Support

• Swap or Cancel and Transfer or Conference Behavior

This section describes the new and changed features in Cisco Unified Communications Manager from release 6.1 to release 7.0(1) and Cisco Unified JTAPI enhancements. It has the following sections:

• Call Pickup

• Calling Party Normalization

• Click to Conference

• Do Not Disturb-Reject

• Extension Mobility Username Login

• Java Socket Connect Timeout

• Join Across Lines with Conference Enhancements (SCCP and SIP)

• Locale Infrastructure Development

• selectRoute() with Calling Search Space and Feature Priority

Note

Cisco Unified Communications Manager release 7.0(1) does not support the following IPv6 related methods: canSupportIPv6() setProviderOpenRetryAttempts (int retryAttempts) getProviderOpenRetryAttempts() getIPAddressingMode() (available on CiscoMediaTerminal and CiscoRouteTerminal interfaces) register(java.net.InetAddress address, int port, CiscoMediaCapability [] capabilities, int[] algorithmIDs, java.net.InetAddress address_v6, int activeAddressingMode) register(CiscoMediaCapability [] capabilities, int[] int registration Type, int[] algorithmIDs, int activeAddressingMode) getTerminals() (available on new interface CiscoProviderTermCapabilityChangedEv) getAddressingModeForMedia() getCallingPartyIpAddr_v6() (available on CiscoCallCtlConnOfferedEv and CiscoRouteEvent interfaces) CTIERR_IPADDRMODEMISMATCH CTIERR_DYNREG_IPADDRMODE_MISMATCH hasIPv6CapabilityChanged() CiscoTerminal.IP_ADDRESSING_MODE_IPv4 CiscoTerminal.IP_ADDRESSING_MODE_IPv6 CiscoTerminal.IP_ADDRESSING_MODE_IPv4_v6 CiscoTerminal.IP_ADDRESSING_MODE_Unknown CiscoTermRegistrationFailedEv.IP_ADDRESSING_MODE_MISMATCH

Note

For the features, Join Across Lines, Do Not Disturb-Reject, and Calling Party Normalization, each Cisco JTAPI must be upgraded to a version that supports these features. Additionally, if you are upgrading from release 5.1 and you use Join Across Lines, the Conference Chaining feature must not be enabled or used until all applications are either upgraded to a version compatible with the new unified CM version. Also, you should verify that the applications are not impacted by the Conference Chaining feature.

This section describes the new and changed features in Cisco Unified Communications Manager from release 6.0 to release 6.1 and Cisco Unified JTAPI enhancements. It has the following sections:

• Certificate Download API Enhancement

• Intercom Support for Extension Mobility

• Join Across Lines

This section describes the new and changed features in Cisco Unified Communications Manager, release 6.0 and Cisco Unified JTAPI enhancements. It has the following sections:

• Arabic and Hebrew Language Support

• Calling Party IP Address

• CiscoRTPHandle Interface on Cisco RTP Events

• Cisco Unified IP 7931G Phone Interaction

• Conference Chaining

• Directed Call Park

• Do Not Disturb

• Forwarding on No Bandwidth and Unregistered DN

• Hold Reversion

• Intercom

• Multilevel Precedence and Preemption Support

• Noncontroller Adding of Parties to Conferences

• Silent Monitoring

• Secure Conferencing

• Translation Pattern Support

• Version Format Change

• Voice MailBox Support

This section describes the new and changed features in Cisco Unified Communications Manager, from release 5.0 to release 5.1 and Cisco Unified JTAPI enhancements. It has the following sections:

• Call Forward Override

• Join Across Lines (Only SCCP)

• New Error Code in CiscoTermRegistrationFailedEv

• Star (*) 50 Update

This section describes the new and changed features in Cisco Unified Communications Manager, from release 4.x to release 5.0 and Cisco Unified JTAPI enhancements. It has the following:

• Auto Updater for Linux

• Call Select Status

• Command Line Invocation

• Hairpin Support

• Half-Duplex Media Support

• JRE 1.2 and JRE 1.3 Support Removal

• JTAPI Client Installer

• JTAPI Version Information

• Linux and Windows Installation

• Network Alerting

• Partition Support

• QoS Support

• Secure Real-Time Protocol Key Material

• Silent Install

• SIP 3XX Redirection

• SIP REFER or REPLACE

• SIP Phone Support

• Superprovider and Change Notification

• Terminal and Address Restrictions

• Transport Layer Security (TLS)

• Unicode Support