Guest

Cisco ONS 15300 Series

Cisco ONS 15302 Quick Installation Guide, Release 1.0

 Feedback

Table Of Contents

Cisco ONS 15302 Quick Installation Guide

Obtaining Documentation

Cisco.com

Documentation CD-ROM

Ordering Documentation

Documentation Feedback

Obtaining Technical Assistance

Cisco.com

Technical Assistance Center

Obtaining Additional Publications and Information

Quick Overview

Before Starting

Translated Warnings

DC Power Disconnection Warning

Main Disconnecting Device

Laser Radiation Warning

Unterminated Fiber Warning

Class 1 Laser Product Warning

Installation Materials for ONS 15302

Installing the ONS 15302

Installing the ONS 15302 in a 19-in. (485-mm) Rack

Installation in Restricted Access Locations

Installing 48-V Power and Ground to the ONS 15302

Install External Ground for 230 V Supply to the ONS 15302

Installing 230-V Power to the ONS 15302

Installing Fiber Patch Cords on the ONS 15302

Routing Fiber Patch Cords

Installing Electrical Cables to the ONS 15302

Routing Electrical Cables

Installation Checklist for ONS 15302

ONSCLI—ONS 15302 Command Line Interface

Introduction to ONSCLI

Accessing ONSCLI

Syntax Rules

Basic Command Syntax

Initial Configuration

Factory Preconfiguration

Important Commands


Quick Start Guide

Cisco ONS 15302 Quick Installation Guide


Release 1.0

January 2003

1 Obtaining Documentation

Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco web sites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Documentation CD-ROM

Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.

Registered Cisco.com users can order the Documentation CD-ROM (product number DOC-CONDOCCD=) through the online Subscription Store:

http://www.cisco.com/go/subscription

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace:

http://www.cisco.com/en/US/partner/ordering/index.shtml

Registered Cisco.com users can order the Documentation CD-ROM (Customer Order Number DOC-CONDOCCD=) through the online Subscription Store:

http://www.cisco.com/go/subscription

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can submit comments electronically on Cisco.com. On the Cisco Documentation home page, click Feedback at the top of the page.

You can e-mail your comments to bug-doc@cisco.com.

You can submit your comments by mail by using the response card behind the front cover of your document or by writing to the following address:

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate your comments.

2 Obtaining Technical Assistance

Cisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) Website, as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC website, including TAC tools and utilities.

Cisco.com

Cisco.com offers a suite of interactive, networked services that let you access Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.

Cisco.com provides a broad range of features and services to help you with these tasks:

Streamline business processes and improve productivity

Resolve technical issues with online support

Download and test software packages

Order Cisco learning materials and merchandise

Register for online skill assessment, training, and certification programs

To obtain customized information and service, you can self-register on Cisco.com at this URL:

http://www.cisco.com

Technical Assistance Center

The Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two levels of support are available: the Cisco TAC website and the Cisco TAC Escalation Center. The avenue of support that you choose depends on the priority of the problem and the conditions stated in service contracts, when applicable.

We categorize Cisco TAC inquiries according to urgency:

Priority level 4 (P4)—You need information or assistance concerning Cisco product capabilities, product installation, or basic product configuration.

Priority level 3 (P3)—Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue.

Priority level 2 (P2)—Your production network is severely degraded, affecting significant aspects of business operations. No workaround is available.

Priority level 1 (P1)—Your production network is down, and a critical impact to business operations will occur if service is not restored quickly. No workaround is available.

Cisco TAC Website

You can use the Cisco TAC website to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC website, go to this URL:

http://www.cisco.com/tac

All customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC website. Some services on the Cisco TAC website require a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to this URL to register:

http://tools.cisco.com/RPF/register/register.do

If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC website, you can open a case online at this URL:

http://www.cisco.com/en/US/support/index.html

If you have Internet access, we recommend that you open P3 and P4 cases through the Cisco TAC website so that you can describe the situation in your own words and attach any necessary files.

Cisco TAC Escalation Center

The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.

To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL:

http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Before calling, please check with your network operations center to determine the level of Cisco support services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). When you call the center, please have available your service agreement number and your product serial number.

3 Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

The Cisco Product Catalog describes the networking products offered by Cisco Systems as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://www.cisco.com/en/US/products/products_catalog_links_launch.html

Cisco Press publishes a wide range of networking publications. Cisco suggests these titles for new and experienced users: Internetworking Terms and Acronyms Dictionary, Internetworking Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL:

http://www.ciscopress.com

Packet magazine is the Cisco monthly periodical that provides industry professionals with the latest information about the field of networking. You can access Packet magazine at this URL:

http://www.cisco.com/en/US/about/ac123/ac114/about_cisco_packet_magazine.html

iQ Magazine is the Cisco monthly periodical that provides business leaders and decision makers with the latest information about the networking industry. You can access iQ Magazine at this URL:

http://business.cisco.com/prod/tree.taf%3fasset_id=44699&public_view=true&kbns=1.html

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in the design, development, and operation of public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_protocol_journal.html

Training—Cisco offers world-class networking training, with current offerings in network training listed at this URL:

http://www.cisco.com/en/US/learning/le31/learning_recommended_training_list.html

4 Quick Overview

The Cisco ONS 15302 is an integrated access device for use in fiber optic networks. The ONS 15302 combines Ethernet- and TDM-traffic inside an SDH STM-1 frame structure that can be easily carried across the network. The bandwidth of the Ethernet channel is configurable up to 100 MBits/s (Mbps) true wire-speed. The Ethernet part of the Cisco ONS 15302 consists of a bridge (see Figure 1).

The ONS 15302 STM-1 port is fully compatible in existing SDH Transport Networks.

Figure 1 ONS 15302 Functional Overview

Each tributary interface is mapped into a VC-12 container while the WAN traffic is mapped into a configurable number of VC-12 containers. Because the latter mapping is proprietary, the Ethernet- WAN generation and termination traffic must be realized in a Cisco device in both ends of a connection.

The ONS 15302 management solution is based on an embedded SNMP agent. A graphical user interface (GUI) based element manager application can be used as a craft terminal and for remote supervision of ONS 15302 devices. The ONS 15302 also provides a simple VT100 command line interface (ONSCLI) for direct communication with the embedded SNMP agent.

5 Before Starting

This guide provides basic instructions for installing the Cisco ONS 15302 system. It contains two different parts:

Installing the ONS 15302

Configure the ONS 15302

Use this guide as a general reference when performing an installation.

For detailed installation instructions, refer to the most recent Cisco ONS 15302 Installation and Operations Guide (Release 1.0).


Caution Always use the supplied ESD wristband when working with an ONS 15302. Plug the wristband cable into the ESD jack of the rack assembly and ensure the rack assembly is properly grounded.

6 Translated Warnings

DC Power Disconnection Warning

Warning


Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Waarschuwing

Voordat u een van de onderstaande procedures uitvoert, dient u te controleren of de stroom naar het gelijkstroom circuit uitgeschakeld is.

Varoitus

Varmista, että tasavirtapiirissä ei ole virtaa ennen seuraavien toimenpiteiden suorittamista.

Attention

Avant de pratiquer l'une quelconque des procédures ci-dessous, vérifier que le circuit en courant continu n'est plus sous tension.

Warnung

Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß die Gleichstromschaltung keinen Strom erhält.

Figyelem!

Mielõtt a következõ eljárások bármelyikét végrehajtaná, feltétlenül szakítsa meg az egyenáramú áramkör tápellátását.

Avvertenza

Prima di svolgere una qualsiasi delle procedure seguenti, verificare che il circuito CC non sia alimentato.

Advarsel

Før noen av disse prosedyrene utføres, kontroller at strømmen er frakoblet likestrømkretsen.

Aviso

Antes de executar um dos seguintes procedimentos, certifique-se que desligou a fonte de alimentação de energia do circuito de corrente contínua.

¡Advertencia!

Antes de proceder con los siguientes pasos, comprobar que la alimentación del circuito de corriente continua (CC) esté cortada (OFF).

Varning!

Innan du utför någon av följande procedurer måste du kontrollera att strömförsörjningen till likströmskretsen är bruten.


Main Disconnecting Device

Warning


The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.

Waarschuwing

De combinatie van de stekker en het elektrisch contactpunt moet te allen tijde toegankelijk zijn omdat deze het hoofdmechanisme vormt voor verbreking van de aansluiting.

Varoitus

Pistoke/liitinkohta toimii pääkatkaisumekanismina. Pääsy siihen on pidettävä aina esteettömänä.

Attention

La combinaison de prise de courant doit être accessible à tout moment parce qu'elle fait office de système principal de déconnexion.

Warnung

Der Netzkabelanschluß am Gerät muß jederzeit zugänglich sein, weil er als primäre Ausschaltvorrichtung dient.

Figyelem!

A dugaszolóaljzat és a dugasz együttesének mindig hozzáférhetõnek kell lennie, mivel ez szolgál fõmegszakítóként.

Avvertenza

Il gruppo spina-presa deve essere sempre accessibile, poiché viene utilizzato come dispositivo di scollegamento principale.

Advarsel

Kombinasjonen støpsel/uttak må alltid være tilgjengelig ettersom den fungerer som hovedfrakoplingsenhet.

Aviso

A combinação ficha-tomada deverá ser sempre acessível, porque funciona como interruptor principal.

¡Advertencia!

El conjunto de clavija y toma ha de encontrarse siempre accesible ya que hace las veces de dispositivo de desconexión principal.

Varning!

Man måste alltid kunna komma åt stickproppen i uttaget, eftersom denna koppling utgör den huvudsakliga frånkopplingsanordningen.


Laser Radiation Warning

Warning


Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.

Waarschuwing

Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze glasvezels of aansluitingen.

Varoitus

Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso niitä suoraan optisilla välineillä.

Attention

Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil. Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments optiques.

Warnung

Unterbrochene Fasern oder Steckerverbindungen können unsichtbare Laserstrahlung abgeben. Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.

Figyelem!

A nem csatlakoztatott üvegszálak és csatlakozók láthatatlan lézersugárzást bocsáthatnak ki. Ne nézzen bele a sugárba, és ne nézze közvetlenül, optikai berendezések segítségével!

Avvertenza

Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici.

Advarsel

Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte inn i strålene eller se på dem direkte gjennom et optisk instrument.

Aviso

Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe diretamente para os feixes ou com instrumentos ópticos.

¡Advertencia!

Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los rayos ni examine éstos con instrumentos ópticos.

Varning!

Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i strålar och titta aldrig direkt på dem med hjälp av optiska instrument.


Unterminated Fiber Warning

Warning


Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.

Waarschuwing

Er kunnen onzichtbare laserstralen worden uitgezonden vanuit het uiteinde van de onafgebroken vezelkabel of connector. Niet in de straal kijken of deze rechtstreeks bekijken met optische instrumenten. Als u de laseruitvoer met bepaalde optische instrumenten bekijkt (zoals bijv. een oogloep, vergrootgras of microscoop) binnen een afstand van 100 mm kan dit gevaar voor uw ogen opleveren.

Varoitus

Päättämättömän kuitukaapelin tai -liittimen päästä voi tulla näkymätöntä lasersäteilyä. Älä tuijota sädettä tai katso sitä suoraan optisilla välineillä. Lasersäteen katsominen tietyillä optisilla välineillä (esim. suurennuslasilla tai mikroskoopilla) 10 cm:n päästä tai sitä lähempää voi olla vaarallista silmille.

Attention

Des émissions de radiations laser invisibles peuvent se produire à l'extrémité d'un câble en fibre ou d'un raccord sans terminaison. Ne pas fixer du regard le rayon ou l'observer directement avec des instruments optiques. L'observation du laser à l'aide certains instruments optiques (loupes et microscopes) à une distance inférieure à 100 mm peut poser des risques pour les yeux.

Warnung

Eine unsichtbare Laserstrahlung kann vom Ende des nicht angeschlossenen Glasfaserkabels oder Steckers ausgestrahlt werden. Nicht in den Laserstrahl schauen oder diesen mit einem optischen Instrument direkt ansehen. Ein Betrachten des Laserstrahls mit bestimmten optischen Instrumenten, wie z.B. Augenlupen, Vergrößerungsgläsern und Mikroskopen innerhalb eines Abstands von 100 mm kann für das Auge gefährlich sein.

Figyelem!

A lezáratlan optikai kábelek és a csatlakozók láthatatlan lézerfényt bocsáthatnak ki. Ne nézzen bele a sugárba, és ne nézze közvetlenül, optikai berendezések segítségével! Ha a kibocsátott lézert 100 mm-esnél kisebb távolságból nézi bizonyos optikai eszközökkel (például nagyítóval vagy mikroszkóppal), látáskárosodást szenvedhet.

Avvertenza

L'estremità del connettore o del cavo ottico senza terminazione può emettere radiazioni laser invisibili. Non fissare il raggio od osservarlo in modo diretto con strumenti ottici. L'osservazione del fascio laser con determinati strumenti ottici (come lupette, lenti di ingrandimento o microscopi) entro una distanza di 100 mm può provocare danni agli occhi.

Advarsel

Usynlig laserstråling kan emittere fra enden av den ikke-terminerte fiberkabelen eller koblingen. Ikke se inn i strålen og se heller ikke direkte på strålen med optiske instrumenter. Observering av laserutgang med visse optiske instrumenter (for eksempel øyelupe, forstørrelsesglass eller mikroskoper) innenfor en avstand på 100 mm kan være farlig for øynene.

Aviso

Radiação laser invisível pode ser emitida pela ponta de um conector ou cabo de fibra não terminado. Não olhe fixa ou diretamente para o feixe ou com instrumentos ópticos. Visualizar a emissão do laser com certos instrumentos ópticos (por exemplo, lupas, lentes de aumento ou microscópios) a uma distância de 100 mm pode causar riscos à visão.

¡Advertencia!

El extremo de un cable o conector de fibra sin terminación puede emitir radiación láser invisible. No se acerque al radio de acción ni lo mire directamente con instrumentos ópticos. La exposición del ojo a una salida de láser con determinados instrumentos ópticos (por ejemplo, lupas y microscopios) a una distancia de 100 mm puede comportar lesiones oculares.

Varning!  

Osynlig laserstrålning kan komma från änden på en oavslutad fiberkabel eller -anslutning. Titta inte rakt in i strålen eller direkt på den med optiska instrument. Att titta på laserstrålen med vissa optiska instrument (t.ex. lupper, förstoringsglas och mikroskop) från ett avstånd på 100 mm kan skada ögonen.


Class 1 Laser Product Warning

Warning


Class 1 laser product.

Waarschuwing

Klasse-1 laser produkt.

Varoitus

Luokan 1 lasertuote.

Attention

Produit laser de classe 1.

Warnung

Laserprodukt der Klasse 1.

Figyelem!

Class 1 besorolású lézeres termék.

Avvertenza

Prodotto laser di Classe 1.

Advarsel

Laserprodukt av klasse 1.

Aviso

Produto laser de classe 1.

¡Advertencia!

Producto láser Clase I.

Varning!

Laserprodukt av klass 1.


7 Installation Materials for ONS 15302

Several items are needed to complete the installation of the ONS 15302. Some of these items are supplied by Cisco and some need to be supplied by the user. The following are the Cisco-supplied materials that are include in the 15302-SHIPKIT= (74-3173-01). The number in parentheses is the quantity of each included item.

Bumper, 12mm diameter, 7 x 3.5 mm for table placing (4)

48-V 4-Pin power connector (1)

Brackets L/R 19" (2)

Brackets L/R ETSI (23") (2)

ONSCLI cable (1)

Blade terminal with screw and blade jack (1)

ESD wrist strap (1)

230-V power cable (1)

Registration card (1)

Warranty card (1)

The following materials, tools, and equipment are recommended but are not supplied with the ONS 15302:

Fuse panel

Power cable (from fuse to power connector), #18 AWG (0.75 mm2) up to #16 AWG (1.5 mm2) with four rigid wire

Yellow green flexible ground cable # 16 AWG (1.25 mm2) up to #14 AWG (2.50 mm2)

Single-mode cable with SC connectors

Fiber connector inspection instruments (Cisco recommends Video Microscopes)

Cletop cleaning cassette (type A for SC connectors)

Caps for optical connectors (SC)

Labels

#1 Phillips screwdriver

#3 Phillips screwdriver

2.5-mm Allen key

4 screws, M6 (#12-24 x 3/4 pan head phillips) and nuts

Voltmeter

Power meter (for use with fiber optics only)

Bit error rate (BER) tester

8 Installing the ONS 15302

To install the ONS 15302, complete the following procedures:

1. Installing the ONS 15302 in a 19-in. (485-mm) Rack

2. Installation in Restricted Access Locations

3. Installing 48-V Power and Ground to the ONS 15302

4. Install External Ground for 230 V Supply to the ONS 15302

5. Installing 230-V Power to the ONS 15302

6. Installing Fiber Patch Cords on the ONS 15302

7. Routing Fiber Patch Cords

8. Installing Electrical Cables to the ONS 15302

9. Routing Electrical Cables

Installing the ONS 15302 in a 19-in. (485-mm) Rack

The shelf assembly is allocated for installation in a 19-in. (485-mm) rack. The ONS 15302 is 17.5-in. (445-mm) wide by 9.4-in. (240-mm) deep by 1.7-in. (44-mm) high.


Step 1 Depending on access requirement, front or rear access, decide which side you want to use as the front side in the rack. Refer to Figure 2 and Figure 3.

Step 2 Remove the four phillips screws on the left and right side of the ONS 15302 and install the brackets with the longer phillips screws that are provided.

Step 3 Move the ONS 15302 to the desired rack position ( Figure 2 and Figure 3).

Step 4 Secure the ONS 15302 to the rack. Tighten the ONS 15302 with four screws ( Figure 2 and Figure 3).

Figure 2 Install the ONS 15302 with the Connector Array in Front in a 19-in. Rack

Figure 3 Install the ONS 15302 with the WAN Module in Front in a 19-in. Rack


Note You can also install the ONS 15302 in a ETSI 23.6-in. (600-mm) rack by using extension brackets to convert it. You need two 1-RU extension brackets to do this.



Installation in Restricted Access Locations

The ONS 15302 can be installed in a restricted access location (RAL) or outside of an RAL.

Definitions

Restricted Access Location

A restricted access location is a site location for equipment where both of the following paragraphs apply:

Access can only be gained by service persons or by users who have been trained on the restrictions and the precautions for this specific site.

Access is by means of at least one of the following, special tool, lock and key, or other means of security.

SELV Circuits

Safety Extra-Low Voltage (SELV) circuits are ports that have maximum DC working voltage level less than 60 V (42.4 VAC). In addition, the ports must not be connected to telecommunication networks as defined in EN 60950 (see CEI/ IEC 60950-1 2001-10, standard clause 1.2.13.8).

In practice, the electrical cables shall not exit the building. In addition, the electrical cables shall connect to equipment that meets one of the following requirements:

Installed in the RAL.

Does not have electrical cables that exit the building unless those ports are TNV (Telecommunication Networks Voltage) circuits.

Has a written consent (or in other evidence) that its connecting port towards the SELV circuit port is not a telecommunication network.

Telecommunication Network

A telecommunication network is a metallically terminated transmission medium intended for communication between equipment that might be located in separate buildings, excluding:

Main system for supply, transmission and distribution of electrical power, if used as a telecommunication transmission medium

Cable distribution system

SELV circuits connecting units of information technology equipment

TNV Circuit

A TNV circuit in the equipment to which the accessible area of contact is limited. A TNV circuit is so designed and protected that, under normal operating conditions and single fault conditions (see CEI/IEC 60950-1 2001-10, standard clause 1.4.14), the voltages do not exceed specified limit values.

IInstallation in Restricted Access Location

After installation in a RAL, such as in a telecommunications center, the ONS 15302 must be properly installed in a rack with brackets or in other ways properly connected to a safety ground. The ONS 15302 48-VDC power must not be powered from a source external to the RAL. The E1 interface used should be limited to SELV.

Installation Outside of a Restricted Access Location

After installation in a non-RAL location, the ONS 15302 48-V power and all communication ports used must be connected to SELV circuits, for example, a port on a personal computer or 10/100-Mbit Ethernet hub/router or other information technology (IT) equipment. The 48-VDC power must not exceed 60 VDC, and must be powered from a certified external power supply unit (PSU) or a battery unit (with no connection to -48 V telecommunications voltage).

The optical ports and 230-VAC power plug have no limitations regarding safety recommendations.

Installing 48-V Power and Ground to the ONS 15302

The power needs to be properly installed and grounded for operation of the ONS 15302. Figure 4 shows the location of the 48-V connector. Use the following procedure to install power and ground to the ONS 15302:


Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.



Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.


Figure 4 ONS 15302 Faceplate (Connector Array)


Step 1 Remove the A- and B-side fuses from the power distribution panel (PDP).

Step 2 Make sure that -48 VDC (tolerance -36 to -72 VDC) power is present.

Step 3 Press a slot screwdriver in the rectangular opening on top of the connector to open the inside contact ( Figure 5).

Step 4 Insert the wire in the contact and remove the screwdriver from the connector.

Step 5 To verify that the wire is properly fix in the unit, pull on the wire.

Step 6 Repeat Step 3 to Step 5 for the other three wires.

Step 7 Affix the four wires on the connector using the two tie wraps to ensure strain relief ( Figure 5).


Note Be sure that the power cable is connected and verify the correct polarity. Check if is properly fused (1.5-A recommended).



Note Note that the ONS 15302 power cannot be switched off with a separate power switch.


Figure 5 Fixing the Wire into the Connector


Install External Ground for 230 V Supply to the ONS 15302


Note This ground connection is only used when the system is powered with 230 VAC and the system is not installed in a rack.


The ONS 15302 should be grounded to the rack ground via the external ground connector.

The location of the ground connector on the ONS 15302 is shown in Figure 6.

Figure 6 Ground Connector Position on the ONS 15302


Step 1 Remove the Phillips screw from the ONS 15302 ( Figure 6).

Step 2 Fix the flat connector with the washer and the socket screw onto the ONS 15302 ( Figure 6).

Step 3 Insert the grounding cable in the flat cable plug and crimp the plug with a crimping tool ( Figure 7).

Step 4 Check whether the ground cable is fixed to the flat cable plug.

Step 5 Connect the flat cable plug to the flat connector.

Step 6 Route the ground cable securely to the local ground connector and connect it according to local site practice.

Figure 7 Connecting of the Ground Cable with a Crimp Tool


Installing 230-V Power to the ONS 15302

The ONS 15302 can also be used as a desk version. This means that it is possibly to connect the ONS 15302 to a public power supply. Figure 4 shows the location of the 230-V connector.


Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.



Note Before installing power to the ONS 15302, be sure that you have the correct power supply recommendations (230 VAC 0.3 A 50Hz).



Note Note that the ONS 15302 power cannot be switched off with a separate power switch.



Step 1 Connect the power cable to the 230-V connector on the ONS 15302.

Step 2 Connect the power cable to the 230-V power supply.

Step 3 To avoid accidents, route the power cable safety through the location.

Installing Fiber Patch Cords on the ONS 15302

The ONS 15302 is available in two different versions: protected and unprotected. In unprotected mode, transmit and receive fibers from the fiber termination rack are connected to STM-1 port 1. In protected mode, transmit and receive fibers from the fiber termination rack are connected to STM-1 port 1 and port 2, ( Figure 4).


Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.



Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.



Warning Class 1 laser product.



Note Clean and inspect SC connectors prior to installation. Any dust particle or damaged connector will affect the optical transmission.


To avoid confusion in the future, label each end of the transmit and receive cables before installation. To install the fiber patch cords, gently push the SC connector into the connector.

For future use (in case of servicing) keep the dust caps in a clean location.


Routing Fiber Patch Cords

After connecting the fibers to and from the fiber termination rack, route the fibers through the rack. Wind the fibers to a loop with a diameter of approximately 3.15 in. (80-mm).

Installing Electrical Cables to the ONS 15302

The ONS 15302 has two different electrical connectors: one DS-9 connector for the alarm interface and 20 RJ-45 connectors for different functions, described in Table 1. The electrical ports on the ONS 15302 are shown in Figure 4.

To avoid confusion in the future, label each end of the cables before installation. To install the electrical cables, gently push the RJ-45 connector into the connector until it snaps in with a click. Screw in the screws from the connector of the alarm cable with a screwdriver.

Table 1 Recommended Cable Types for the ONS 15302

Port Name
Quantity
Recommended Cable Type
Used for

ALARM

1

UTP

External alarm management

LAN

4

UTP Category 5 for 100-Mbits/s (Mbps) Ethernet

LAN or WAN connections (10/100 Mbits/s [Mbps])

SYNC

1

UTP (The outer screen of the SYNC cable is always connected to ground [pin 6]).

Input and output synchronization

VT100 (CLI)

1

UTP (Category 1) supplied from Cisco

CLI connections (cable supplied by Cisco)

MNGT (Management)

1

UTP Category 5

Connection to a remote craft terminal

USER CH

1

UTP Category 1

User application

TRIB (Tributary)

12

STP

Tributary connections

STM-1

2 or 4

Single-mode fiber according to ITU-T G.652

Optical connections



Routing Electrical Cables

After connecting the cable to the ONS 15302, route the cable through the rack without damage it.

Installation Checklist for ONS 15302

The following list is an installation checklist. Use this list as a reference when performing an installation. For detailed installation instructions, refer to the Cisco ONS 15302 Installation and Operations Guide (Release 1.0). To check the installation, verify the following items:

ONS 15302 is mounted securely in the rack.

Power runs to the ONS 15302.

Transmit and receive fiber patch cords from the fiber termination are correctly connected to the ONS 15302.

Fiber-optic patch cords route through the rack.

Electrical cables route through the rack.

Each cable is labeled.

9 ONSCLI—ONS 15302 Command Line Interface

Introduction to ONSCLI

ONSCLI is a line-oriented ASCII-based management interface to ONS 15302. It is used to issue simple commands—possibly with parameter—to access or modify the ONS 15302 configuration.

Accessing ONSCLI

ONSCLI is accessed via the VT100-port or via an IP connection (Telnet). The serial connection communications parameters are fixed ( Table 2). VT100 terminal codes are used.

Table 2 EIA/TIA-232 Parameters

Parameter
Value

Speed

19200 bps

Data bits

8

Parity

None

Stop bits

1

Flow control

None


The VT100-port (Console port) for the ONS 15302 is provided using a RJ-45 connector.

Invoke an ONSCLI Session

An ONSCLI session is invoked by typing ONSCLI at the CLI terminal.

User authentication (a password containing between 8 and 12 ASCII characters, with no case sensitivity) is required, as the following session start-up sequence shows:

>
>ONSCLI

---------------------------------------------------
          ONS 15302 Command Line Interface
---------------------------------------------------

Enter ONSCLI password: ******

ONSCLI>


Note The default password for the ONS 15302 is ONSCLI.


Incorrect Password

Each password characters is echoed as *. An incorrect password is rejected with the message:

invalid password

After the password is rejected, the password prompt is re-issued.


Note The number of attempts is 3.


An authorized ONSCLI user has full access rights to the available management information.

Exit

The Exit command is used to terminate an ONSCLI session. The ONSCLI session is automatically terminated after a period of 30 minutes of inactivity. ONSCLI does not accept simultaneous sessions.

Syntax Rules

An ONSCLI command line begins with a prompt (issued by ONSCLI), which serves to indicate the current position in the command hierarchy.

An ONSCLI command is issued by typing the command followed by Enter. Optionally, and only at the lowest level in the command hierarchy, one or more parameters can also be supplied. These are identified by keywords. The command name, parameter keywords, and parameter values are delimited by one or more spaces. Command line editing features are listed in Table 3.


Note It is only necessary to type sufficient leading characters of the command name to avoid ambiguity—the same applies to keywords.


Table 3 Command Line Editing Features

Key
Result

Delete or Backspace

Erases the character in the command line.

Arrow left

Moves the cursor to the left side.

Arrow right

Moves the cursor to the right side.

Arrow Up

Recalls the previous command in command history.

Arrow Up

Recalls the previous command in command history.

Return or Enter

At the command line, processes a command.

..

Returns to the previous command level.

\

Goes to the top command level.

?

Issues a list of commands valid at the current level, or shows the command usage.


ONSCLI Commands are listed in Table 4

Table 4 ONSCLI Commands

Command
Result

Free

Shows VC-12 containers that are not yet utilized.

Used

Lists the VC-12 container(s) in use.

Status

Presents current device and port status.

Exit

Exits ONSCLI.


Some commands (in particular the show command) can potentially produce many lines of output. After a predetermined number of lines of output in response to a single command, the user is prompted to enter y(es) or n(o) to continue the output. The default line number limit is 23 and maximum is 998. For detailed information about the ONSCLI commands, refer to the Cisco ONS 15302 Installation and Operations Guide (Release 1.0).

Basic Command Syntax

A basic command has the syntax shown in Example 1.

Example 1 Basic Command Syntax

<basic command>      ::= [<path>]<command> [<parameter>]... <CR>
<path>               ::= [\]<command\>[<command>\]...
<command>            ::= <command name> | ..
<parameter>          ::= <spaces> <keyword>=<value> | ?
<value>              ::= <integer> |
							<choice> |
							<IP address> |
							<string> |
							<MAC address> |
							<NSAP address> |
							<time> |
							<date> |
							<KLM> |
							<portList> |
							<port>
<NSAP address>					::= <area address>:<system id>:<selector>
<portList>					::= <port>[,<port>]..
<areaAddressList>					::= <area address>[,<area address>]...

where:
<spaces>				is a string of one or more ASCII spaces;

<integer>				is a decimal integer in the range [m:n], where the values m and n are 
				context-dependent;

<choice>				is a literal string, whose permissible values and their significance are 
				context-dependent and may be obtained by using the help (?) parameter;

<IP address>				is an IP address of the form ddd.ddd.ddd.ddd,  where d is a decimal digit. 
				Leading zeroes in each ddd may be omitted;

<string>				is a string of graphical ASCII characters, excluding  quotation marks ("). 
				If the string contains one or more spaces, then it MUST be enclosed in 
				quotation marks. The maximum length of the string is context-dependent;

<MAC address>				is exactly 12 hexadecimal digits;

<time>				is a time-of-day of the form hh:mm:ss, where h, m and s are decimal digits;

<date>				is a date of the form dd/mm/yy, where d, m and y are decimal digits;
<KLM>				is a string of the form k.l.m,  where k is a decimal digit in the range 
				[1:3],  l is a decimal digit  in the range [1:7], and  m is a decimal digit 
				in the range [1:3]. 
<port>				is a decimal integer;
<area address>				is a hexadecimal string;
<system id>				is a hexadecimal string;
<selector>				is a hexadecimal string;

For a complete overview of the ONSCLI command hierarchy, please refer the Cisco ONS 15302 Installation and Operations Guide (Release 1.0).

The Help Command

The help command (?) displays all available commands at the current level, each with a short description. For example, typing ? at the root level lists the commands that are available at this level, as shown in Example 2.

Example 2 Help Command

ONSCLI>?
*** current menu path:
<root>
*** valid commands:
Device:     Device configuration
Ports:      Port properties
Bridge:     Bridge/Spanning Tree Protocol settings
Security:   Security settings
Statistics: Performance monitoring and statistics
Services:   Utility functions
Alarms:     Current alarms and alarm history
Status:     Device status
Free:       List of free VC12
Used:       List of used VC12
Exit:       Exit from ONSCLI

Command Hierarchy

In the command hierarchy, the lowest level is represented by a basic command with one or more parameters.

Example 3 modifies only the IP address.

Example 3 Selecting the IP Address

ONSCLI\Device\Management-Configuration\Management-Mode MODE=ipManagementPort

ONSCLI\Device\Management-Configuration\IP-Management-Port\ IP-Configuration IP-ADDRESS=193.69.136.104

For most commands, if no parameters are supplied then all the current parameter values are displayed ( Example 4).

Example 4 Displays the IP Configuration

ONSCLI\Device\Management-Configuration\IP-Management-Port\IP-Configuration

Example 4 displays the current management interface information in the following manner:

IP-ADDRESS:	193.69.136.104
SUBNET-MASK:	 255.255.255.0
DEFAULT-GATEWAY: 193.69.136.54

If the help parameter (?) is supplied, then all other parameters are ignored and the basic command usage is displayed.

Table entries are accessed by introducing an additional command level giving access to the entire table. At this lowest level, the Add command (with the index and required table entries as parameters) can be used to add an element to the table and the Edit command can be used to replace an existing element in the table (if these operations are permitted on the table).

Similarly the Remove command (with the entry index as a parameter) can be used to remove an existing element from the table if this is permitted.

The Show command (with an entry index value as a parameter) displays the specified table entry. If no parameter is supplied with the Show command, the current contents of the entire table is displayed.

ONSCLI Error Messages

SNMP Errors

The general ONSCLI output string for SNMP errors is MIB access error. Additional SNMP error information might be printed depending on the return code ( Table 5).

Table 5 Additional ONSCLI SNMP Error Messages

Error Message (Output String)
Description

No Such Object

Scalar or table entry not found

End Of MIB View

End of table reached

No Creation

Creation of new entry failed

Not Writable

Accessed instance write protected

Wrong Length

Wrong specified field length

Wrong Value

Wrong value used for specified field

Inconsistent Value

Wrong value used for specified field

Resource Unavailable

Instance status not free for update

General Error

No additional error info

No Write To CDB

Write to Flash failed

Instance Exists

Table entry already exists


Input Errors

Error messages due to mistyping or incorrect ONSCLI input format are shown in Table 6.

Table 6 ONSCLI Input Error Messages 

Error Message (Output String)
Description

Unknown parameter specification

Input parameter incorrectly specified

Ambiguous parameter specification

Parameter value out of range

Multiple parameter specification

Input parameter specified twice

Missing parameter specification

Mandatory parameter missing

Incompatible parameter specification

Wrong combination of parameters

Missing value

Wrong formatted or empty input value

Invalid integer value

Wrong input integer value

Invalid choice value

Input value (set element name) not found

Invalid length of string value of

Input string too long

Badly-formed string value of

Input string incorrectly formatted

Invalid IP address

IP address incorrectly formatted

Invalid length of hex string

Length of hex string not according to input requirement

Invalid character in hex string

Hex value used to define a digit is out of range.

Invalid escape sequence in string

'\0' value detected inside the string

Bad value

Incorrectly formatted input value

Integer out of range

Input integer value is not within limits.

List too long

List of integers longer than 10

Badly-formed list

Incorrect integer value found in integer list

Table empty

No entries found in SNMP table

Element not in table

Specified entry not found in SNMP table

This command is not available in this release

Command not supported

No modification parameters found

Modification command with no modification values received


10 Initial Configuration

By following the guides below you should be able to do the most important configurations of ONS 15302.

Factory Preconfiguration

Since the ONS 15302 is a flexible product with a lot of possible network applications, the factory preconfiguration is limited when delivered. Ethernet ports 1 to 5 are members of VLAN 1, the aggregate (STM-1) is enabled, and one VC-12 container is allocated to the Ethernet WAN (port number 5). In addition, an entry in the SNMP community table is preconfigured so that when an IP address is assigned, the ONS 15302 is able to take advantage of the GUI element manager. This configuration persists, regardless of whether the WAN module is inserted or not.


Note If you erase the configuration on the device, the factory preconfiguration will disappear. A backup file is the easiest solution to store the factory preconfiguration.


Important Commands

Follow the steps in this section to perform initial configuration of the ONS 15302. The following tasks are the most important tasks involved in the configuration of an ONS 15302:

Assign an IP Address to the ONS 15302

Select Synchronization Source

Configure Ethernet WAN Bandwidth

Assign a VC-12 Container and Activate a 2-MBit/s (Mbps) Tributary Port

Define SNMPv1 Community

Erase a Community String

Assign an IP Address to the ONS 15302

The ONS 15302 supports remote management solutions by the means of Telnet, SNMP, and through an Internet browser (Netscape or Microsoft Internet Explorer). Several advanced connectivity options are available with the ONS 15302. This document describes the simplest method—direct connection through the MNGT port. For more information, please refer to the Cisco ONS 15302 Installation and Operations Guide (Release 1.0).

To achieve connectivity for remote management solutions, you must first assign an IP address, subnet mask, and, if required, a default gateway address, as shown in Example 5.

Example 5 Assigning an IP Address

ONSCLI\Device\Management-Configuration\Management-Mode MODE=ipManagementPort

Press Enter

Change management configuration, are you sure? (y/n)

Press y, then Enter

MODE: IP-Management-Port

ONSCLI\Device\Management-Configuration\Management-Mode\Customize
ONSCLI\Device\Management-Configuration\Custom\Management-Port\IP-Configuration IP-ADDRESS=10.0.0.1 
SUBNET-MASK=255.255.255.0 DEFAULT-GATEWAY=10.0.0.254

Press Enter

IP-ADDRESS:       10.0.0.1
SUBNET-MASK:      255.255.255.0
DEFAULT-GATEWAY:  10.0.0.254	

Select Synchronization Source

There are several alternatives for synchronization of the ONS 15302. You can choose whether to receive synchronization from a local oscillator, from one of the tributaries, from the aggregate port, or through the dedicated SYNC port.

By default, the synchronization source is a local oscillator, but if, for example, the ONS 15302 interfaces an SDH node on the optical STM-1 interface, you must change the synchronization source to aggregate. To do this, use the command shown in Example 6.

Example 6 Selecting the Synchronization Source

ONSCLI>Device\sync-source admin-source=aggr1

Press Enter

ADMIN-SOURCE:  		aggr1
OPERATIONAL-SOURCE:  	Holdover 	

Configure Ethernet WAN Bandwidth


Note The ONS 15302 can have up to four Ethernet WAN ports. When factory preconfigured, the only bandwidth allocated is 2.16 Mbits/s (Mbps) for the internal WAN-port 5, which means that one VC-12 container is selected.


One of the benefits for the ONS 15302 is that you can choose between all 63 of the VC-12 containers available in the STM-1 frame (limited to 50 VC-12 containers for the Ethernet WAN ports). Forty-seven VC-12 containers are sufficient for operating at 100 MBits/s (Mbps).

The VC-12 containers needed to achieve the desired bandwidth must be selected in the same order at both ends of the link. In a back-to-back configuration using two ONS 15302s, this implies that the KLM-scheme (the VC-12 mapping scheme in a VC-4 container) used must be identical. In a larger network, where the VC-12s might be cross-connected, only the sequence must be identical.

To simplify the allocation of bandwidth, the number of VC-12 containers needed can be entered together with the desired sort-mode. The VC-12s can be sorted according to ITU-T G.707 or in Lexicographic-order. The default sort-mode is Lexicographic-order.

The following example shows how bandwidth can easily be allocated for the Ethernet WAN port by selecting a number of VC-12 containers.


Step 1 Enter the WAN-port level in ONSCLI and type ? to view the available commands, as shown in the following example:

ONSCLI>Ports\Ethernet-Port-Properties\WAN-Port(s)\?

Press Enter

*** current menu path: 

<root> 
  Ports 
    Ethernet-Port-Properties 
      WAN-Port(s) 

*** valid commands: 

General:             WAN port general settings 
Add-VC12-channel:    Add a VC12 to WAN port 
Edit-VC12-channel:   Modify Admin Status of a VC12  
Remove-VC12-channel: Remove a VC12 from WAN port(always the last) 
Status:              Device status 
Free:                List of free VC12 
Used:                List of used VC12 
Exit:                Exit from ONSCLI 

Step 2 Type general to see the current status for the WAN-port(s), as shown in the following example:

ONSCLI>...\WAN-Port(s)\general

Press Enter

WAN-PORT:         5 
OPER-CAPACITY:    0. Mbps. 
OPER-VC12-NBR:    0 
ADMIN-CAPACITY:   0. Mbps. 
ADMIN-VC12-NBR:   0 
PATH-TRACE:       disabled 
EXPECTED-TI:      <Path-trace J2> 
HEX-EXPECTED-TI:  3C,50,61,74,68,2D,74,72,61,63,65,20,4A,32,3E 
TRANSMIT-TI:      <Path-trace J2> 
HEX-TRANSMIT-TI:  3C,50,61,74,68,2D,74,72,61,63,65,20,4A,32,3E 
RECEIVED-TI: 
HEX-RECEIVED-TI:  00,00,00,00,00,00,00,00,00,00,00,00,00,00,00 
CHANNEL-TI:       0 

---------------------------------------------- 
KLM      WAN-CHANNEL ADMIN-STATUS OPER-STATUS 
---------------------------------------------- 
KLM table empty.                 

Step 3 Type Add-VC12-channel ? to see the attributes available for the command, as shown in the following example:

ONSCLI>...\WAN-Port(s)\Add-VC12-channel ?

Press Enter

Usage: 
   Add-VC12-channel 

WAN-PORT=<integer value 5:8> (Only port 5 if WAN-module not present)
[KLM=<K.L.M - integer value 1:3.integer value 1:7.integer value 1:3>] (Optional starting point if 
desirable to add multiple VC-12 containers to a WAN-port)
[ADMIN-STATUS=<enabled|disabled>] (Optional, by default enabled)
[NUMBER-TO-ADD=<integer value 1:50>] (Optional, if desirable to simplify allocation of multiple VC-12 
containers)
[SORT-MODE=<LEX|G707>] (Optional, by default the "lexigraphic order")

Step 4 Configure the needed number of VC-12 containers to a selected WAN port, as shown in the following example:

ONSCLI>...\WAN-Port(s)\Add-VC12-channel wan-port=5 klm=1.1.1 admin-status=enabled number-to-add=10 
sort-mode=g707

Press Enter

Adding klm 1.1.1 ok
Adding klm 2.1.1 ok
Adding klm 3.1.1 ok
Adding klm 1.2.1 ok
Adding klm 2.2.1 ok
Adding klm 3.2.1 ok
Adding klm 1.3.1 ok
Adding klm 2.3.1 ok
Adding klm 3.3.1 ok
Adding klm 1.4.1 ok

WAN-PORT:         5 
OPER-CAPACITY:    0. Mbps. 
OPER-VC12-NBR:    0 
ADMIN-CAPACITY:   21.60 Mbps. 
ADMIN-VC12-NBR:   10 
PATH-TRACE:       disabled 
EXPECTED-TI:      <Path-trace J2> 
HEX-EXPECTED-TI:  3C,50,61,74,68,2D,74,72,61,63,65,20,4A,32,3E 
TRANSMIT-TI:      <Path-trace J2> 
HEX-TRANSMIT-TI:  3C,50,61,74,68,2D,74,72,61,63,65,20,4A,32,3E 
RECEIVED-TI: 
HEX-RECEIVED-TI:  00,00,00,00,00,00,00,00,00,00,00,00,00,00,00 
CHANNEL-TI:       0 

---------------------------------------------- 
KLM      WAN-CHANNEL ADMIN-STATUS OPER-STATUS 
---------------------------------------------- 
1.1.1    1           enabled      down 
2.1.1    2           enabled      down 
3.1.1    3           enabled      down 
1.2.1    4           enabled      down 
2.2.1    5           enabled      down 
3.2.1    6           enabled      down 
1.3.1    7           enabled      down 
2.3.1    8           enabled      down 
--- More (y/n)? y	"ENTER"

3.3.1    9           enabled      down 
1.4.1    10          enabled      down 

ONSCLI>...\WAN-Port(s)\

Assign a VC-12 Container and Activate a 2-MBit/s (Mbps) Tributary Port

The procedure for assigning a VC-12 container to a tributary port on the ONS 15302 is quite similar to allocation of bandwidth to an Ethernet WAN port. The same flexibility is maintained for the selection of VC-12 containers.

Use the following procedure to configure and activate a tributary port on the ONS 15302:


Step 1 Assign a VC-12 container to a tributary port, as shown in the following example:

ONSCLI>Ports\TRIB-Ports\Assign-VC12-Channel ?

Usage: 

   Assign-VC12-Channel 

TRIB-PORT=<integer value 1:12> (Select the Trib-port you would like to assign a VC-12 container. If 
desirable to assign multiple Trib-ports this will be the starting point)
[KLM=<K.L.M - integer value 1:3.integer value 1:7.integer value 1:3>] (Optional, if a specific KLM 
reference is desirable. When assigning multiple Trib-ports simultaneously, this will be the staring point 
in the mapping scheme.)  
[NUMBER-TO-ADD=<integer value 1:12>] (Optional, desirable number of Trib-ports in multiple assignment)
[SORT-MODE=<LEX|G707>] (Optional, by default the "lexigraphic order")


ONSCLI>...\TRIB-Ports\assign-vc12-channel trib-port=1 klm=3.7.3

Press Enter


---------------------- 
TRIB-PORT       KLM 
---------------------- 
1               3.7.3 

Step 2 Enable and select the transmission parameters for the Trib port, as shown in the following example:

ONSCLI>...\TRIB-Ports\general ?

Press Enter

Usage: 

   General 

[TRIB-PORT=<integer value 1:12>] (Select desired Trib-port)
[DESCRIPTION=<string[0:64]>] (Optional)
[ADMINISTRATIVE-STATUS=<enable|disable>] (Select enable)
[MODE=<TRA|PRA>] (Optional, default transparent (TRA) acc. to G.703)
[LOOP-MODE=<NONE|LL2|LL3>] (Optional, for tests)
[PATH-TRACE=<enabled|disabled>] (Optional)
[EXPECTED-TI=<string[1:15]>] (Optional)
[HEX-EXPECTED-TI=<string[2:44]>] (Optional)
[TRANSMIT-TI=<string[1:15]>] (Optional)
[HEX-TRANSMIT-TI=<string[2:44]>] (Optional)

ONSCLI>...\TRIB-Ports\general trib-port=1 description=qrg administrative-status=enable mode=pra

Press Enter


TRIB-PORT:              1 
DESCRIPTION:            qrg 
ADMINISTRATIVE-STATUS:  enable 
OPERATIONAL-STATUS:     down 
MODE:                   PRA 
KLM:                    3.7.3 
LOOP-MODE:              NONE 
PATH-TRACE:             disabled 
EXPECTED-TI:            <Path-trace J2> 
HEX-EXPECTED-TI:        3C,50,61,74,68,2D,74,72,61,63,65,20,4A,32,3E 
TRANSMIT-TI:            <Path-trace J2> 
HEX-TRANSMIT-TI:        3C,50,61,74,68,2D,74,72,61,63,65,20,4A,32,3E 
RECEIVED-TI:             
HEX-RECEIVED-TI:        00,00,00,00,00,00,00,00,00,00,00,00,00,00,00 

ONSCLI>...\TRIB-Ports\


Define SNMPv1 Community

The factory preconfigured SNMPv1 community is shown in Example 7.

Example 7 Factory Preconfigured SNMPv1 Community

ONSCLI>Security\Community-Table\Show

Press Enter


Manager:			0.0.0.0
Community:			public
Access:			super
Traps:			disable

This is an insecure community that enables all managers to access the device with the community string public, regardless of the IP address of the SNMP manager .

To add your own community string, use the following command:

ONSCLI>Security\Community-Table\Add MANAGER=10.0.0.20 COMMUNITY=admin ACCESS=super TRAPS=enable

Press Enter

Erase a Community String

To remove a community string, use the following command:

ONSCLI>Security\Community-Table\Remove MANAGER=0.0.0.0 COMMUNITY=public

Press Enter