The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
[no] fast-external-fallover
| no |
Negate a command or set its defaults |
| fast-external-fallover |
Immediately reset the session if the link to a directly connected BGP peer goes down |
[no] fast-flood enable
| no |
Negate a command or set its defaults |
| fast-flood |
Fast flood the LSP's |
| enable |
Turn on fast-flooding |
| level |
IS-IS level
|
[no] fast-flood interval interval
| no |
Negate a command or set its defaults |
| fast-flood |
Fast flood the LSP's |
| interval |
Duration/interval of the fast-flood timer. |
| level |
IS-IS level
|
| interval |
Type: uinteger min: 1 max: 3000 default: 1 Specify the value (ms) |
feature-set fs
| feature-set |
Enable feature-set |
| fs |
Type: userdef allow feature-set |
[no] feature arg1
| no |
Negate a command or set its defaults |
| feature |
Feature name |
| arg1 |
Type: string length: 32 Enter feature name |
[no] feature "bash-shell"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| bash-shell |
Enable/Disable bash-shell |
[no] feature bfd
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| bfd |
bfd |
[no] feature bgp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| bgp |
Enable/Disable Border Gateway Protocol (BGP) |
[no] feature cts
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| cts |
Enable/Disable CTS Not available in this release. |
[no] feature dhcp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| dhcp |
Enable/Disable DHCP Manager |
[no] feature eigrp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| eigrp |
Enable/Disable Enhanced Interior Gateway Routing Protocol (EIGRP) |
[no] feature evmed
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| evmed |
Enable/Disable Generic event detectors |
[no] feature glbp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| glbp |
Enable/Disable Gateway Load Balancing Protocol (GLBP) Not available in this release. |
[no] feature hsrp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| hsrp |
Enable/Disable Hot Standby Router Protocol (HSRP) |
[no] feature interface-vlan
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| interface-vlan |
Enable/Disable interface vlan |
[no] feature isis
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| isis |
Enable/Disable IS-IS Unicast Routing Protocol (IS-IS) |
[no] feature lacp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| lacp |
Enable/Disable LACP |
[no] feature "ldap"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| ldap |
Enable/Disable ldap |
[no] feature lldp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| lldp |
Enable/Disable LLDP |
[no] feature msdp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| msdp |
Enable/Disable Multicast Source Discovery Protocol (MSDP) |
[no] feature ntp
| no |
Negate a command or set its default |
| feature |
Command to enable/disable features |
| ntp |
Enable/Disable NTP |
[no] feature nv overlay
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| nv |
Enable/Disable VxLAN Available only in the 9300 series. |
| overlay |
Enable/Disable VxLAN Available only in the 9300 series. |
[no] feature "nxapi"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| nxapi |
Enable/Disable nxapi |
[no] feature ospf
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| ospf |
Enable/Disable Open Shortest Path First Protocol (OSPF) |
[no] feature ospfv3
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| ospfv3 |
Enable/Disable Open Shortest Path First Version 3 Protocol (OSPFv3) |
[no] feature password encryption aes
| no |
Negate a command or set its defaults |
| feature |
Enable the feature |
| password |
Credential(s) for the user(s)/device(s) |
| encryption |
Strong encryption for credential(s) |
| aes |
Encrypt using AES encryption standard |
[no] feature pim
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| pim |
Enable/Disable Protocol Independent Multicast (PIM) |
[no] feature poap
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| poap |
Enable/Disable POAP |
[no] feature pong
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| pong |
Enable/Disable Pong Not available in this release. |
[no] feature private-vlan
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| private-vlan |
Enable/Disable private-vlan Not available in this release. |
[no] feature privilege
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| privilege |
Enable/Disable IOS type privilege level support |
[no] feature rip
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| rip |
Enable/Disable Routing Information Protocol (RIP) |
[no] feature scheduler
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| scheduler |
Enable/Disable scheduler |
[no] feature "scp-server"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| scp-server |
Enable/Disable SCP server |
[no] feature "sftp-server"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| sftp-server |
Enable/Disable SFTP server |
[no] feature "ssh"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| ssh |
Enable/Disable ssh |
[no] feature "tacacs+"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| tacacs+ |
Enable/Disable tacacs+ |
[no] feature "telnet"
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| telnet |
Enable/Disable telnet |
[no] feature udld
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| udld |
Enable/Disable UDLD |
[no] feature vn-segment-vlan-based
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| vn-segment-vlan-based |
Enable/Disable VLAN based VN segment Available only in the 9300 series. |
[no] feature vpc
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| vpc |
Enable/Disable VPC (Virtual Port Channel) |
[no] feature vrrp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| vrrp |
Enable/Disable Virtual Router Redundancy Protocol (VRRP) |
[no] feature vtp
| no |
Negate a command or set its defaults |
| feature |
Command to enable/disable features |
| vtp |
Enable/Disable VTP |
[no] fex chas_no
| no |
Negate the command |
| fex |
FEX configuration |
| chas_no |
Type: integer min: 101 max: 199 FEX number |
fex associate chassis_no [ chassis-serial serial_no [ module-serial mod_serial ] [ module-slot { left | right } ] ] | no fex associate [chassis_no]
| no |
Negate a command or set its defaults |
| fex |
Configure FEX fabric |
| associate |
Associate the port to a FEX |
| chassis_no |
Type: uinteger min: 101 max: 199 FEX number |
| chassis-serial |
Chassis serial number |
| serial_no |
Type: string length: 20 Serial number |
| module-serial |
Module serial number |
| mod_serial |
Type: string length: 20 Module serial number |
| module-slot |
Module Slot |
| left |
Left IO module slot |
| right |
Right IO module slot |
fex management-instance inst fabric fabric_no | no fex management-instance
| no |
Negate a command or set its defaults |
| fex |
FEX configuration |
| management-instance |
Management instance configuration |
| inst |
Type: string length: 40 Management Instance |
| fabric |
Left fabric or Right fabric |
| fabric_no |
Type: uinteger min: 1 max: 2 Fabric number |
fex pinning redistribute rchas_id
| fex |
FEX control commands |
| pinning |
Pinning redistribution |
| redistribute |
Redistribute FEX ports to fabric ports |
| rchas_id |
Type: uinteger min: 101 max: 199 FEX number |
filesys delete s0
| filesys |
file system command |
| delete |
delete a file on file system |
| s0 |
Type: string file name |
[no] filter [ subject-name s0 | altname-email s1 | altname-upn s2 ]
| no |
Negate a command or set its defaults |
| filter |
Configure mapping filter |
| subject-name |
Subject name of the certificate |
| s0 |
Type: string length: 64 Subject name |
| altname-email |
Email id as an alternate name |
| s1 |
Type: string length: 64 Email id |
| altname-upn |
User principal name as an alternate name |
| s2 |
Type: string length: 64 User principal name |
[no] filter access-group acl-name
| no |
Negate a command or set its defaults |
| filter |
Filter configuration |
| access-group |
access control group |
| acl-name |
Type: string access control list name |
[no] filter vlan vlan_mrange [include-untagged]
| no |
Negate a command or set its defaults |
| filter |
Filter configuration |
| vlan |
Vlan type |
| vlan_mrange |
Type: vlan-mrange |
| include-untagged |
Include untagged frames on port with Layer 3 subinterfaces Not available in this release. |
[no] filter vlan include-untagged
| no |
Negate a command or set its defaults |
| filter |
Filter configuration |
| vlan |
Vlan type |
| include-untagged |
Include untagged frames on port with Layer 3 subinterfaces Not available in this release. |
find s0
| find |
Find a file below the current directory |
| s0 |
Type: string length: 64 Enter the filename prefix to search |
[no] fips mode enable
| no |
Negate a command or set its defaults |
| fips |
Enable/Disable FIPS mode Not available in this release. |
| mode |
FIPS mode |
| enable |
Enable/Disable FIPS mode |
flowcontrol { receive rx_flowctrl | send tx_flowctrl } | no flowcontrol { receive [ rx_flowctrl ] | send [ tx_flowctrl ] }
| no |
Negate a command or set its defaults |
| flowcontrol |
Configure interface flowcontrol Not available in this release. |
| receive |
Receive pause frames |
| rx_flowctrl |
Receive flow control
|
| send |
Send pause frames |
| tx_flowctrl |
Send flow control
|
[no] flowcontrol hardware
| no |
Negate a command or set its defaults |
| flowcontrol |
Set flow control |
| hardware |
Set hardware flowcontrol |
[no] flush-routes
| no |
Negate a command or set its defaults |
| flush-routes |
Flush routes in RIB upon controlled restart |
[no] flush-routes
| no |
Negate a command or set its defaults |
| flush-routes |
Flush routes in RIB during restart |
[no] flush-routes
| no |
Negate a command or set its defaults |
| flush-routes |
Flush routes on non-graceful controlled restart |
[no] flush-routes
| no |
Negate a command or set its defaults |
| flush-routes |
Flush routes on a non-graceful controlled restart |
[no] flush-routes
| no |
Negate a command or set its defaults |
| flush-routes |
Flush routes on a non-graceful controlled restart |
[no] flush-routes
| no |
Negate a command or set its defaults |
| flush-routes |
Flush routes in RIB during restart |
forceshut [ module module | s0 santa-cruz-range | zone zonenum subzone ] reset-reason reset_reason_string
| forceshut |
Force the entire switch to shut down |
| module |
Optional. Module to be forceshut(optional arg) |
| module |
Type: integer please enter the module number |
| s0 |
Type: xbar-str Power off a specific xbar |
| santa-cruz-range |
Type: integer please enter the xbar number |
| zone |
Optional. Zone to be forceshut(optional arg) |
| zonenum |
Type: integer min: 1 max: 2 please enter the zone number |
| subzone |
Type: integer min: 1 max: 7 please enter the subzone number |
| reset-reason |
Shut down (with reset-reason) |
| reset_reason_string |
Type: string please enter reset_reason_string in quotes |
format bootflash :
| format |
Format disks |
| bootflash: |
Format bootflash: |
format bootflash : check-filesystem
| format |
Format disks |
| bootflash: |
Format bootflash: |
| check-filesystem |
Format bootflash: and fix any errors in file system |
format logflash :
| format |
Format disks |
| logflash: |
Format logflash: |
format logflash : check-filesystem
| format |
Format disks |
| logflash: |
Format logflash: |
| check-filesystem |
Format logflash: and fix any errors in file system |
format usb1 :
| format |
Format disks |
| usb1: |
Format usb1: |
format usb2 :
| format |
Format disks |
| usb2: |
Format usb2: |
[no] forwarder preempt [ delay minimum min-delay ]
| no |
Negate a command or set its defaults |
| forwarder |
Forwarder Configuration |
| preempt |
Overthrow lower priority designated routers |
| delay |
Wait before preempting |
| minimum |
Delay at least this long |
| min-delay |
Type: integer min: 0 max: 3600 Number of seconds for minimum delay |
[no] { platform | hardware } forwarding interface statistics mode { mpls | default } [ module module-num ]
| no |
Negate a command or set its defaults |
| platform |
Platform configuration commands |
| hardware |
Hardware Internal Information |
| forwarding |
Hardware forwarding |
| interface |
Interface Not available in this release. |
| statistics |
Statistics |
| mode |
Statistics mode |
| mpls |
Mpls mode |
| default |
Default mode |
| module |
Specify a module number |
| module-num |
Type: integer Specify a module number |
[no] { platform | hardware } forwarding layer-2 f1 exclude supervisor
| no |
Negate a command or set its defaults |
| platform |
Platform configuration commands |
| hardware |
Hardware Internal Information |
| forwarding |
Forwarding information |
| layer-2 |
L2 only mode Not available in this release. |
| f1 |
N7K-F132XP-15 module Not available in this release. |
| exclude |
Exclude supervisor from getting copies of ARP and multicast packets |
| supervisor |
Supervisor module |
[no] fragments opt_type
| no |
Negate a command or set its defaults |
| fragments |
Optimize fragments rule installation |
| opt_type |
frag_op_type
|
[no] { from frm-list to to-val | default { value | copy | ignore } }
| no |
Negate a command or set its defaults |
| from |
Map values from this |
| frm-list |
Type: integer-mrange Original list of values which are to be mapped |
| to |
Map values to this |
| to-val |
Type: uinteger min: 0 max: 63 New mapped value |
| default |
map default values |
| value |
Type: uinteger min: 0 max: 63 default value to be set |
| copy |
Do a default copy |
| ignore |
Ignore any unspecified values |
Feedback