Cisco Nexus 9000 Series NX-OS Command Reference (Configuration Commands), Release 6.1(2)I2(2)

name (glbp)

name redundancy-name | no name [redundancy-name]

Syntax Description


no	Negate a command or set its defaults
name	Redundancy name
`redundancy-name`	Type: string length: 250 Name String

Command Modes

/exec/configure/if-eth-any/glbp

name (hsrp_engine)

name name | no name

Syntax Description


no	Negate a command or set its defaults
name	Redundancy name string
`name`	Type: string length: 250 name string

Command Modes

/exec/configure/if-eth-any/hsrp_ipv4
/exec/configure/if-eth-any/hsrp_ipv6

name-lookup (ospf)

[no] name-lookup

Syntax Description


no	Negate a command or set its defaults
name-lookup	Display OSPF router ids as DNS names

Command Modes

/exec/configure/router-ospf
/exec/configure/router-ospf/vrf

name-lookup (ospfv3)

[no] name-lookup

Syntax Description


no	Negate a command or set its defaults
name-lookup	Enable Name Lookup for OSPF Neighbors

Command Modes

/exec/configure/router-ospf3
/exec/configure/router-ospf3/vrf

name (stp_full)

name name-val | no name [name-val]

Syntax Description


no	Negate a command or set its defaults
name	Set configuration name
`name-val`	Type: string Configuration name

Command Modes

/exec/configure/spanning-tree/mst/configuration

name (vlan_mgr_cli)

name vlan-name | no name

Syntax Description


no	Negate a command or set its defaults
name	Ascii name of the VLAN
`vlan-name`	Type: string length: 128 The ascii name for the VLAN

Command Modes

/exec/configure/vlan

neighbor (bgp)

[no] neighbor { neighbor-id | ipv6-neighbor-id } [ remote-as asn ]

Syntax Description


no	Negate a command or set its defaults
neighbor	Configure a BGP neighbor
`neighbor-id`	Type: ipaddr IP address of the neighbor
`ipv6-neighbor-id`	Type: ipv6addr IPv6 address of the neighbor
remote-as	Specify Autonomous System Number of the neighbor
`asn`	Type: asn Autonomous System Number

Command Modes

/exec/configure/router-bgp/router-bgp-vrf

neighbor (bgp)

[no] neighbor { neighbor-prefix | ipv6-neighbor-prefix } [ remote-as [ asn | route-map rmap-name ] ]

Syntax Description


no	Negate a command or set its defaults
neighbor	Configure a BGP neighbor
`neighbor-prefix`	Type: ipprefix IP prefix for neighbors
`ipv6-neighbor-prefix`	Type: ipv6prefix IPv6 prefix for neighbors
remote-as	Specify Autonomous System Number of the neighbor
`asn`	Type: asn Autonomous System Number
route-map	Route-map to match prefix peer AS number
`rmap-name`	Type: string pattern: [!-~]* length: 63 Route-map name

Command Modes

/exec/configure/router-bgp

neighbor (bgp)

[no] neighbor { neighbor-prefix | ipv6-neighbor-prefix } [ remote-as [ asn | route-map rmap-name ] ]

Syntax Description


no	Negate a command or set its defaults
neighbor	Configure a BGP neighbor
`neighbor-prefix`	Type: ipprefix IP prefix for neighbors
`ipv6-neighbor-prefix`	Type: ipv6prefix IPv6 prefix for neighbors
remote-as	Specify Autonomous System Number of the neighbor
`asn`	Type: asn Autonomous System Number
route-map	Route-map to match prefix peer AS number
`rmap-name`	Type: string pattern: [!-~]* length: 63 Route-map name

Command Modes

/exec/configure/router-bgp/router-bgp-vrf

neighbor (bgp)

[no] neighbor { neighbor-id | ipv6-neighbor-id } [ remote-as asn ]

Syntax Description


no	Negate a command or set its defaults
neighbor	Configure a BGP neighbor
`neighbor-id`	Type: ipaddr IP address of the neighbor
`ipv6-neighbor-id`	Type: ipv6addr IPv6 address of the neighbor
remote-as	Specify Autonomous System Number of the neighbor
`asn`	Type: asn Autonomous System Number

Command Modes

/exec/configure/router-bgp

neighbor-down fib-accelerate

[no] neighbor-down fib-accelerate

Syntax Description


no	Negate a command or set its defaults
neighbor-down	Handle BGP neighbor down event, due to various reasons
fib-accelerate	Accelerate the hardware updates for IP/IPv6 adjacencies for neighbor

Command Modes

/exec/configure/router-bgp/vrf-cmds

neighbor (eigrp)

{ neighbor address { interface | maximum-prefix value [warning-only] } | no neighbor address [ interface | maximum-prefix value [warning-only] ] } | { neighbor maximum-prefix value [threshold] [warning-only] [ restart time1 ] [ restart-count count ] [ reset-time time2 ] [dampened] | no neighbor maximum-prefix [ value [threshold] [warning-only] [ restart time1 ] [ restart-count count ] ] }

Syntax Description


no	Negate a command or set its defaults
neighbor	Specify a neighbor router
`interface`	Type: interface Interface
`address`	Type: ipaddr Neighbor address
maximum-prefix	Maximum number of IP prefixes acceptable from a neighbor
`value`	Type: uinteger min: 1 max: 0 Number of IP prefixes for maximum-prefix limit
`threshold`	Type: integer Threshold value (%) at which to generate a warning message
warning-only	Only give warning message when limit is exceeded
restart	Duration for which a prefix source is ignored
`time1`	Type: integer min: 1 max: 0 Restart interval in minutes
restart-count	Number of times sessions are auto-restarted
`count`	Type: integer min: 1 max: 0 Number of times
reset-time	Duration after which restart history is cleared
`time2`	Type: integer min: 1 max: 0 Reset time in minutes
dampened	Exponentially increase restart time interval

Command Modes

/exec/configure/router-eigrp/router-eigrp-vrf-common
/exec/configure/router-eigrp/router-eigrp-af-common

net

[no] net net

Syntax Description


no	Negate a command or set its defaults
net	Configure Network Entity Title for IS-IS
`net`	Type: net NET in form of XX.XXXX. ... .XXXX.XX

Command Modes

/exec/configure/router-isis/router-isis-vrf-common

network (bgp)

[no] network ipv6-prefix [ route-map rmap-name | summarize ] +

Syntax Description


no	Negate a command or set its defaults
network	Configure an IPv6 prefix to advertise
`ipv6-prefix`	Type: ipv6prefix IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128
route-map	Apply route-map to modify attributes
`rmap-name`	Type: string pattern: [!-~]* length: 63 Route-map name
summarize	Summarize more specific prefixes from routing table

Command Modes

/exec/configure/router-bgp/router-bgp-af-ipv6
/exec/configure/router-bgp/router-bgp-vrf-af-ipv6

network (bgp)

[no] network { ip-addr mask ip-mask | ip-prefix } [ route-map rmap-name | summarize ] +

Syntax Description


no	Negate a command or set its defaults
network	Configure an IP prefix to advertise
`ip-addr`	Type: ipaddr IP network to advertise
mask	Configure the mask of the IP prefix to advertise
`ip-mask`	Type: ipaddr Dotted 4-octet mask
`ip-prefix`	Type: ipprefix IP prefix in CIDR format
route-map	Apply route-map to modify attributes
`rmap-name`	Type: string pattern: [!-~]* length: 63 Route-map name
summarize	Summarize more specific prefixes from routing table

Command Modes

/exec/configure/router-bgp/router-bgp-af-ipv4
/exec/configure/router-bgp/router-bgp-vrf-af-ipv4

network (eigrp)

[no] network { address mask | prefix }

Syntax Description


no	Negate a command or set its defaults
network	Enable routing on an IP network
`address`	Type: ipaddr Network number
`mask`	Type: ipaddr EIGRP wild card bits
`prefix`	Type: ipprefix IP prefix in slash format

Command Modes

/exec/configure/router-eigrp/router-eigrp-vrf-common
/exec/configure/router-eigrp/router-eigrp-af-ipv4

network (rip)

[no] network { ip-dest ip-mask | ip-prefix }

Syntax Description


no	Negate a command or set its defaults
network	RIP IP network
`ip-dest`	Type: ipaddr IP addr format
`ip-mask`	Type: ipaddr IP network mask format
`ip-prefix`	Type: ipprefix Exact prefix

Command Modes

/exec/configure/router-rip/router-rip-af-ipv4
/exec/configure/router-rip/router-rip-vrf-af-ipv4

network area

[no] network { ip-dest ip-mask | ip-prefix } area { area-id-ip | area-id-int }

Syntax Description


no	Negate a command or set its defaults
network	Enable routing on an IP network
`ip-dest`	Type: ipaddr IP prefix format: i.i.i.i
`ip-mask`	Type: ipaddr IP network mask format: m.m.m.m
`ip-prefix`	Type: ipprefix IP prefix format: x.x.x.x/ml
area	Configure area properties
`area-id-ip`	Type: ipaddr OSPF area ID in IP address format
`area-id-int`	Type: uinteger min: 0 max: 4294967295 OSPF area ID as a decimal format

Command Modes

/exec/configure/router-ospf
/exec/configure/router-ospf/vrf

next-hop-self

[ no | default ] next-hop-self

Syntax Description


no	Negate a command or set its defaults
default	Inherit values from a peer template
next-hop-self	Set our peering address as nexthop

Command Modes

/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af
/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

next-hop-self eigrp

[no] { ip | ipv6 } next-hop-self eigrp eigrp-ptag

Syntax Description


no	Negate a command or set its defaults
ip	Configure IP features
ipv6	Configure IPv6 features
next-hop-self	Configures IP-EIGRP next-hop-self
eigrp	EIGRP interface configuration commands
`eigrp-ptag`	Type: string pattern: [a-zA-Z0-9_][a-zA-Z0-9_-]* antipattern: accounting \| all \| fsm \| graceful-restart \| interface \| interfaces \| internal \| neighbor \| neighbors \| notifications \| packets \| prefix \| route \| route-map \| shutdown \| summary \| topology \| traffic \| transmit \| urib \| vrf \| vrf-events length: 20 Process tag

Command Modes

/exec/configure/if-igp

next-hop-third-party

[ no | default ] next-hop-third-party

Syntax Description


no	Negate a command or set its defaults
default	Inherit values from a peer template
next-hop-third-party	Compute a third-party nexthop if possible

Command Modes

/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af
/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

nexthop route-map

[no] nexthop route-map rmap-name

Syntax Description


no	Negate a command or set its defaults
nexthop	Nexthop tracking
route-map	Route map for valid nexthops
`rmap-name`	Type: string pattern: [!-~]* length: 63 Route-map name

Command Modes

/exec/configure/router-bgp/router-bgp-af
/exec/configure/router-bgp/router-bgp-af-ipv4-mdt
/exec/configure/router-bgp/router-bgp-af-l2vpn-vpls

nexthop trigger-delay critical non-critical

nexthop trigger-delay critical criticaldelay non-critical noncriticaldelay | no nexthop trigger-delay

Syntax Description


no	Negate a command or set its defaults
nexthop	Nexthop tracking
trigger-delay	Set the delay to trigger nexthop tracking
critical	Nexthop changes affecting reachability
non-critical	Other nexthop changes
`noncriticaldelay`	Type: uinteger min: 1 max: 4294967295 default: 10000 Delay value (miliseconds)
`criticaldelay`	Type: uinteger min: 1 max: 4294967295 default: 3000 Delay value (miliseconds)

Command Modes

/exec/configure/router-bgp/router-bgp-af
/exec/configure/router-bgp/router-bgp-af-ipv4-mdt
/exec/configure/router-bgp/router-bgp-af-vpnv4
/exec/configure/router-bgp/router-bgp-af-vpnv6
/exec/configure/router-bgp/router-bgp-af-l2vpn-vpls

no (aclmgr)

no seqno

Syntax Description


no	Negate a command or set its defaults
`seqno`	Type: uinteger min: 1 max: 4294967295 Sequence number

Command Modes

/exec/configure/ipacl
/exec/configure/ipv6acl
/exec/configure/macacl
/exec/configure/arpacl
/exec/configure/ipgroup
/exec/configure/ipv6group
/exec/configure/portgroup
/exec/configure/timerange

no (ldap_tree)

no { userprofile | trustedCert | CRLLookup | user-switch-bind | user-certdn-match | user-pubkey-match }

Syntax Description


no	Negate a command or set its defaults
userprofile	Delete the userprofile
trustedCert	Delete the trustedCert
CRLLookup	Delete the CRLLookup
user-switch-bind	Delete the user-switch-bind
user-certdn-match	Delete the certificate matching
user-pubkey-match	Delete the pubkey matching

Command Modes

/exec/configure/ldap/search

no-more

" | " no-more

Syntax Description


\|	Pipe command output to filter
no-more	Turn-off pagination for command output

Command Modes

/output

ntp access-group

[no] ntp access-group { peer | serve-only | serve | query-only } acl-name

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
access-group	NTP access-group
peer	access-group peer
serve	access-group serve
serve-only	access-group serve-only
query-only	access-group query-only
`acl-name`	Type: string Name of access list

Command Modes

/exec/configure

ntp authenticate

[no] ntp authenticate

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
authenticate	Enable/Disable authentication

Command Modes

/exec/configure

ntp authentication-key md5

[no] ntp authentication-key number md5 md5 [ 0 | 7 ]

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
authentication-key	NTP authentication key
`number`	Type: integer min: 1 max: 65535 authentication key number (range 1-65535)
md5	use md5 authentication scheme
`md5`	Type: string length: 15 MD5 string
0	clear text
7	encrypted

Command Modes

/exec/configure

ntp drop-aged-packet

[no] ntp drop-aged-packet

Syntax Description


no	Negate a command or set its defaults
ntp	NTP Configuration
drop-aged-packet	Enable or disable Riviera Timestamp Check.

Command Modes

/exec/configure

ntp logging

[no] ntp logging

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
logging	Enable/Disable logging of NTPD Events

Command Modes

/exec/configure

ntp master

[no] ntp master [stratum-no]

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
master	Act as NTP master clock
`stratum-no`	Type: integer min: 1 max: 15 Stratum number

Command Modes

/exec/configure

ntp peer

[no] ntp peer host0 [ prefer | key keyid | use-vrf { vrf-name | vrf-known-name } | minpoll minpoll | maxpoll maxpoll ] +

Syntax Description


no	Negate a command or set its defaults
ntp	NTP Configuration
peer	NTP Peer address
`host0`	Type: nameorip Hostname/IP address of the NTP Peer
prefer	Preferred Server
key	Keyid to be used while communicating to this server
`keyid`	Type: integer min: 1 max: 65535 Value of keyid 1-65535
use-vrf	Display per-VRF information
`vrf-name`	Type: vrf pattern: [-a-zA-Z0-9_:;$#@]* antipattern: vrf \| detail \| interface \| definition \| context \| forwarding \| member \| all \| l2-vrf \| topology \| passive length: 32 VRF name
`vrf-known-name`	Type: vrf Known VRF name
minpoll	Minimum interval to poll a peer
`minpoll`	Type: integer min: 4 max: 17 Poll interval in secs to a power of 2 [default 4]
maxpoll	Maximum interval to poll a peer
`maxpoll`	Type: integer min: 4 max: 17 Poll interval in secs to a power of 2 [default 6]

Command Modes

/exec/configure

ntp rts-update

[no] ntp rts-update

Syntax Description


no	Negate a command or set its defaults
ntp	NTP Configuration
rts-update	Enable or disable RTS update to linecards.

Command Modes

/exec/configure

ntp server

[no] ntp server host0 [ prefer | key keyid | use-vrf { vrf-name | vrf-known-name } | minpoll minpoll | maxpoll maxpoll ] +

Syntax Description


no	Negate a command or set its defaults
ntp	NTP Configuration
server	NTP server address
`host0`	Type: nameorip Hostname/IP address of the NTP Server
prefer	Preferred Server
key	Keyid to be used while communicating to this server
`keyid`	Type: integer min: 1 max: 65535 Value of keyid 1-65535
use-vrf	Display per-VRF information
`vrf-name`	Type: vrf pattern: [-a-zA-Z0-9_:;$#@]* antipattern: vrf \| detail \| interface \| definition \| context \| forwarding \| member \| all \| l2-vrf \| topology \| passive length: 32 VRF name
`vrf-known-name`	Type: vrf Known VRF name
minpoll	Minimum interval to poll a server
`minpoll`	Type: integer min: 4 max: 16 Poll interval in secs to a power of 2 [default 4]
maxpoll	Maximum interval to poll a server
`maxpoll`	Type: integer min: 4 max: 16 Poll interval in secs to a power of 2 [default 6]

Command Modes

/exec/configure

ntp source-interface

[no] ntp source-interface if_index

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
source-interface	Source interface sending NTP packets
`if_index`	Type: interface Source interface

Command Modes

/exec/configure

ntp source

[no] ntp source ip-addr

Syntax Description


no	Negate a command or set its default
ntp	NTP Configuration
source	Source of NTP packets
`ip-addr`	Type: string IPv4/IPv6 address

Command Modes

/exec/configure

ntp sync-retry

Syntax Description


ntp	NTP configuration
sync-retry	Retry synchronization with configured servers

Command Modes

/exec

ntp trusted-key

[no] ntp trusted-key number

Syntax Description


no	Negate a command or set its default
ntp	NTP configuration
trusted-key	NTP trusted-key
`number`	Type: integer min: 1 max: 65535 trusted-key number

Command Modes

/exec/configure

nxapi

nxapi { http | https } port s0 | no nxapi { http | https }

Syntax Description


no	Negate a command or set its defaults
nxapi	Configure nxapi
`s0`	Type: integer min: 1 max: 65535 Port number. Please do not use well-known protocol ports
http	Http configuration
https	Https configuration
port	Port number

Command Modes

/exec/configure

nxapi certificate httpskey httpscrt keyfile certfile enable

nxapi certificate { httpskey { keyfile uri0 | line } | httpscrt { certfile uri1 | line1 } | enable }

Syntax Description


no	Negate a command or set its defaults
nxapi	Configure nxapi
certificate	Https certificate configuration
httpskey	Https private key
httpscrt	Https certificate
keyfile	Https key file
certfile	Https certificate file
enable	Enable the current certificate
`uri0`	Type: uri File containing https private key for the user
`line`	Type: remainder nxapi https private key
`uri1`	Type: uri File containing https certificate
`line1`	Type: remainder nxapi https certificate

Command Modes

/exec/configure

Bias-Free Language

Results

Chapter: N Commands

N Commands

name (glbp)

Syntax Description

Command Modes

name (hsrp_engine)

Syntax Description

Command Modes

name-lookup (ospf)

Syntax Description

Command Modes

name-lookup (ospfv3)

Syntax Description

Command Modes

name (stp_full)

Syntax Description

Command Modes

name (vlan_mgr_cli)

Syntax Description

Command Modes

neighbor (bgp)

Syntax Description

Command Modes

neighbor (bgp)

Syntax Description

Command Modes

neighbor (bgp)

Syntax Description

Command Modes

neighbor (bgp)

Syntax Description

Command Modes

neighbor-down fib-accelerate

Syntax Description

Command Modes

neighbor (eigrp)

Syntax Description

Command Modes

net

Syntax Description

Command Modes

network (bgp)

Syntax Description

Command Modes

network (bgp)

Syntax Description

Command Modes

network (eigrp)

Syntax Description

Command Modes

network (rip)

Syntax Description

Command Modes

network area

Syntax Description

Command Modes

next-hop-self

Syntax Description

Command Modes

next-hop-self eigrp

Syntax Description

Command Modes

next-hop-third-party

Syntax Description

Command Modes

nexthop route-map

Syntax Description

Command Modes

nexthop trigger-delay critical non-critical

Syntax Description

Command Modes

no (aclmgr)

Syntax Description

Command Modes

no (ldap_tree)

Syntax Description

Command Modes