T Commands

table-map (isis)

[no] table-map policy-name [filter]

Syntax Description

no

Negate a command or set its defaults
table-map

Table-map policy used to filter routes & tune attributes before downloading to RIB
filter

Filter the routes based on policy results
policy-name

Type: string

length: 63

A 'routing-rules' route-map name

Command Modes

  • /exec/configure/router-isis/router-isis-af-ipv6

table-map (qosmgr)

table-map default-tmap-enum-name

Syntax Description

table-map

Configure a table map Not available in this release.
default-tmap-enum-name
cir-markdown-map  value: 1
Exceed color markdown map
pir-markdown-map  value: 2
Violate color markdown map

Command Modes

  • /exec/configure

table-map (bgp)

[no] table-map rmap-name [filter]

Syntax Description

no

Negate a command or set its defaults
table-map

Apply table-map to filter routes downloaded into URIB
rmap-name

Type: string

pattern: [!-~]*

length: 63

Route-map name
filter

Selective route download

Command Modes

  • /exec/configure/router-bgp/router-bgp-af

table-map (eigrp)

[no] table-map map [filter]

Syntax Description

no

Negate a command or set its defaults
table-map

Configure Table Map information
map

Type: string

pattern: [!-~]*

length: 63

Route-map name
filter

Filter routes which are rejected by route-map

Command Modes

  • /exec/configure/router-eigrp/router-eigrp-vrf-common
  • /exec/configure/router-eigrp/router-eigrp-af-common

table-map (isis)

[no] table-map policy-name [filter]

Syntax Description

no

Negate a command or set its defaults
table-map

Table-map policy used to filter routes & tune attributes before downloading to RIB
filter

Filter the routes based on policy results
policy-name

Type: string

length: 63

A 'routing-rules' route-map name

Command Modes

  • /exec/configure/router-isis/router-isis-vrf-common
  • /exec/configure/router-isis/router-isis-af-ipv4

table-map (ospf)

[no] table-map policy-name [filter]

Syntax Description

no

Negate a command or set its defaults
table-map

Policy for filtering/modifying OSPF routes before sending them to RIB
policy-name

Type: string

pattern: [!-~]*

length: 63

Route-map name
filter

To block the OSPF routes from being sent to RIB

Command Modes

  • /exec/configure/router-ospf
  • /exec/configure/router-ospf/vrf

table-map (ospfv3)

[no] table-map policy-name [filter]

Syntax Description

no

Negate a command or set its defaults
table-map

Policy for filtering/modifying OSPFV3 routes before sending them to RIB
policy-name

Type: string

pattern: [!-~]*

length: 63

Route-map name
filter

To block the OSPFV3 routes from being sent to RIB

Command Modes

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6
  • /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

table-map (qosmgr)

[no] table-map table-map-name

Syntax Description

no

Negate a command or set its defaults
table-map

Configure a table map Not available in this release.
table-map-name

Type: string

length: 40

Table map name

Command Modes

  • /exec/configure

tac-pac (syscli)

tac-pac [ uri0 [ vrf vrf-known-name ] ]

Syntax Description

tac-pac

save tac info in a compressed .gz file at specific location
uri0

Type: uri

Select destination filesystem
vrf

Display per-VRF information
vrf-known-name

Type: vrf

Known VRF name

Command Modes

  • /exec

tac-pac (syscli)

tac-pac [uri0]

Syntax Description

tac-pac

save tac info in a compressed .gz file at specific location
uri0

Type: uri

Select destination filesystem

Command Modes

  • /exec

tacacs-server deadtime

[no] tacacs-server deadtime i0

Syntax Description

no

Negate a command or set its defaults
tacacs-server

Configure TACACS+ server related parameters
deadtime

duration for which non-reachable server is skipped
i0

Type: integer

min: 0  max: 1440  

Length of time, in minutes

Command Modes

  • /exec/configure

tacacs-server directed-request

[no] tacacs-server directed-request

Syntax Description

no

Negate a command or set its defaults
tacacs-server

Configure TACACS+ server related parameters
directed-request

enable direct authentication requests to server

Command Modes

  • /exec/configure

tacacs-server host

[no] tacacs-server host hostipname { key { 0 s0 | 6 s6 | 7 s1 | s2 } [ port i1 ] [ timeout i2 ] | [ port1 i3 ] [ timeout1 i4 ] } | no tacacs-server host hostipname key

Syntax Description

no

Negate a command or set its defaults
tacacs-server

Configure TACACS+ server related parameters
host

TACACS+ server's DNS name or its IP address
hostipname

Type: nameorip

IPV4/IPV6 address or DNS name
key

TACACS+ shared secret
0

TACACS+ shared secret(clear text)
s0

Type: string

length: 63

TACACS+ shared secret(clear text)
port

TACACS+ server port
i1

Type: integer

min: 1  max: 65535  

TACACS+ server port
timeout

TACACS+ server timeout period in seconds
i2

Type: integer

min: 1  max: 60  

TACACS+ server timeout period in seconds
6

TACACS+ shared secret(type-6 encrypted)
s6

Type: string

length: 124

TACACS+ shared secret(encrypted)
7

TACACS+ shared secret(encrypted)
s1

Type: string

length: 63

TACACS+ shared secret(encrypted)
port1

TACACS+ server port
i3

Type: integer

min: 1  max: 65535  

TACACS+ server port
timeout1

TACACS+ server timeout period in seconds
i4

Type: integer

min: 1  max: 60  

TACACS+ server timeout period in seconds
s2

Type: string

length: 63

TACACS+ shared secret(clear text)

Command Modes

  • /exec/configure

tacacs-server key 0

[no] tacacs-server key { 0 s0 [ timeout i0 ] | 6 s6 [ timeout6 i6 ] | 7 s1 [ timeout1 i1 ] | s2 [ timeout2 i2 ] } | no tacacs-server key

Syntax Description

no

Negate a command or set its defaults
tacacs-server

Configure TACACS+ server related parameters
key

Global TACACS+ server shared secret
0

default TACACS+ shared secret(clear text)
s0

Type: string

length: 63

default TACACS+ shared secret(clear text)
timeout

Global TACACS+ server timeout period in seconds
i0

Type: integer

min: 1  max: 60  

Global TACACS+ server timeout period in seconds
6

default TACACS+ shared secret(type-6 encrypted)
s6

Type: string

length: 124

default TACACS+ shared secret(type-6 encrypted)
timeout6

Global TACACS+ server timeout period in seconds
i6

Type: integer

min: 1  max: 60  

Global TACACS+ server timeout period in seconds
7

default TACACS+ shared secret(encrypted)
s1

Type: string

length: 63

default TACACS+ shared secret(encrypted)
timeout1

Global TACACS+ server timeout period in seconds
i1

Type: integer

min: 1  max: 60  

Global TACACS+ server timeout period in seconds
s2

Type: string

length: 63

default TACACS+ shared secret(clear text)
timeout2

Global TACACS+ server timeout period in seconds
i2

Type: integer

min: 1  max: 60  

Global TACACS+ server timeout period in seconds

Command Modes

  • /exec/configure

tacacs-server timeout

[no] tacacs-server timeout i0

Syntax Description

no

Negate a command or set its defaults
tacacs-server

Configure TACACS+ server related parameters
timeout

Global TACACS+ server timeout period in seconds
i0

Type: integer

min: 1  max: 60  

Global TACACS+ server timeout period in seconds

Command Modes

  • /exec/configure

tacacs+ enable

[no] "tacacs+" enable

Syntax Description

no

Negate a command or set its defaults
tacacs+

Enable tacacs+
enable

Enable tacacs+

Command Modes

  • /exec/configure

tag happens in

[no] tag tag_id op tag_id [ op tag_id [ op tag_id ] ] happens threshold in interval | no tag

Syntax Description

no

Negate a command or set its defaults
tag

event tag identifier
tag_id

Type: string

length: 029

tag name
op

boolean operator

and  value: 001
Use boolean and logic
or  value: 003
Use boolean or logic
andnot  value: 002
Use boolean andnot logic
happens

The number of occurrences before raising the event
threshold

Type: uinteger

min: 1  max: 4294967295  

Occurs value
in

Number of occurrences must occur within this time period
interval

Type: uinteger

min: 0  max: 4294967295  

Enter seconds value

Command Modes

  • /exec/configure/event-manager-applet

tail (clic)

" | " tail [ -n lines ]

Syntax Description

|

Pipe command output to filter
tail

Display last lines
-n

modify number of lines (default 10)
lines

Type: integer

number of lines to print

Command Modes

  • /output

tail (util_cli)

tail uri0 [i1]

Syntax Description

tail

Display the last part of a file
uri0

Type: uri

Filename to be displayed
i1

Type: integer

min: 0  max: 80  

Enter the number of lines to be displayed

Command Modes

  • /exec

tar

tar { create new-archive-file [ gz-compress | bz2-compress | uncompressed ] + [ remove | absolute | verbose ] + files+ | append archive-file [ remove | absolute | verbose ] + files+ | extract archive-file [ screen | to dest-dir | keep-old | verbose ] + | list archive-file }

Syntax Description

tar

archiving operations
create

create an archive (merge several files together)
append

append some files to an existing archive
extract

extract files from archive (unmerge them)
verbose

display files while merging/extracting
gz-compress

compress archive with gzip, the default -> .tar.gz
bz2-compress

compress archive with bzip2 -> .tar.bz2
uncompressed

dont compress archive -> .tar
remove

remove files after adding them to the archive
absolute

don't strip leading `/'s from file names
keep-old

don't replace existing files when extracting
screen

extract files to screen
list

shows the list of files which are part of the archive
new-archive-file

Type: uri

the name of the archive (extension will be added if none of tar/tgz/tar.gz/tar.bz2/tbz2/tar.Z specified)
archive-file

Type: uri

the name of the archive (extension will be added if none of tar/tgz/tar.gz/tar.bz2/tbz2/tar.Z specified)
files

Type: uri

name of file to be added into archive
to

extract to specific directory (default is bootflash)
dest-dir

Type: uri

destination dir where to extract to (created if not exist), default is bootflash

Command Modes

  • /exec

tclsh (clic)

tclsh

Syntax Description

tclsh

Execute tclsh

Command Modes

  • /exec

tclsh (clic)

tclsh file [args] +

Syntax Description

tclsh

source tclsh script
file

Type: uri

the file to run

args

Type: string

args to tcl script

Command Modes

  • /exec

telnet

telnet { so | host } [i0] [ [ source { host_src | interface } ] [ vrf { vrf-name | vrf-known-name } ] ]

Syntax Description

telnet

Telnet to another system
so

Type: string

length: 64

Enter hostname

host

Type: ipaddr

Enter a valid IPv4 address
source

Set source address in IPv4 header
host_src

Type: ipaddr

Set IPV4 address as source
interface

Type: interface

Set interface to send IPv4 packet
vrf

Display per-VRF information
vrf-name

Type: vrf

pattern: [-a-zA-Z0-9_:;$#@]*

antipattern: vrf | detail | interface | definition | context | forwarding | member | all | l2-vrf | topology | passive

length: 32

VRF name
vrf-known-name

Type: vrf

Known VRF name
i0

Type: integer

min: 1  max: 65535  

Enter the port number

Command Modes

  • /exec

telnet6

telnet6 { s1 | host1 } [i0] [ [ source { host1_src | interface } ] [ vrf { vrf-name | vrf-known-name } ] ]

Syntax Description

telnet6

Telnet6 to another system using IPv6 addressing
s1

Type: string

length: 64

Enter hostname

host1

Type: ipv6addr

Enter a valid IPv6 address
source

Set source address in IPv6 header
host1_src

Type: ipv6addr

Set IPV6 address as source
interface

Type: interface

Set interface to send IPv6 packet
vrf

Display per-VRF information
vrf-name

Type: vrf

pattern: [-a-zA-Z0-9_:;$#@]*

antipattern: vrf | detail | interface | definition | context | forwarding | member | all | l2-vrf | topology | passive

length: 32

VRF name
vrf-known-name

Type: vrf

Known VRF name
i0

Type: integer

min: 1  max: 65535  

Enter the port number

Command Modes

  • /exec

telnet server enable

[no] telnet server enable

Syntax Description

no

Negate a command or set its defaults
telnet

Enable telnet
server

Enable telnet
enable

Enable telnet

Command Modes

  • /exec/configure

template

template res-mgr-template-known-name-all

Syntax Description

template

Change the template for this vdc
res-mgr-template-known-name-all

Type: string

Resource template for this vdc

Command Modes

  • /exec/configure/vdc

template peer

[no] template peer peer-template-name

Syntax Description

no

Negate a command or set its defaults
template

Enter template command mode
peer

Template configuration for peer parameters
peer-template-name

Type: string

length: 80

Neighbor template name

Command Modes

  • /exec/configure/router-bgp

template peer-policy

[no] template peer-policy peer-policy-template-name

Syntax Description

no

Negate a command or set its defaults
template

Enter template command mode
peer-policy

Template configuration for policy parameters
peer-policy-template-name

Type: string

length: 80

Name of peer-policy template

Command Modes

  • /exec/configure/router-bgp

template peer-session

[no] template peer-session peer-session-template-name

Syntax Description

no

Negate a command or set its defaults
template

Enter template command mode
peer-session

Template configuration for session parameters
peer-session-template-name

Type: string

length: 80

Name of peer-session template

Command Modes

  • /exec/configure/router-bgp

terminal

terminal { monitor | no { monitor1 | monitor-force } }

Syntax Description

terminal

Set terminal line parameters
monitor

Copy Syslog output to the current terminal line
no

Negate a command or set its defaults
monitor1

Copy Syslog output to the current terminal line
monitor-force

Copy Syslog output to the current terminal line

Command Modes

  • /exec

terminal alias

[no] terminal alias [persist] [ alias-name [command] ]

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
alias

show aliases (if no arugments); create 'exec' aliases (not persistent). Persistent aliases are in config mode, see 'cli alias'
persist

add terminal alias to <username>.rc.cli file (auto-execed at login time)
alias-name

Type: string

Name of the alias. (if last argument: shows the value of that alias) Command lines can start with an alias and it will be expanded before parsing. An alias can also be used right after a pipe. The substitution text can contain things like '$1 $2' and those $<number> will be substituted by correspondingly numbered token from the command line starting the counting after the alias.

command

Type: remainder

Value of the alias (what the alias will be substituted with)

Command Modes

  • /exec

terminal color

[no] terminal color [persist]

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
color

enable colorization of prompt(green if last command ok, red if error), command line (blue), output (default color)
persist

add command to <username>.rc.cli file (auto-execed at login time)

Command Modes

  • /exec

terminal context management

[no] terminal context management

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
context

set the vrf context
management

vrf context management

Command Modes

  • /exec
  • /exec

terminal deep-help

[no] terminal deep-help

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
deep-help

enable cli syntax and list

Command Modes

  • /exec

terminal dont-ask

[no] terminal dont-ask [persist]

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
dont-ask

Don't ask 'are you sure' questions, take default answer instead
persist

add command to <username>.rc.cli file (auto-execed at login time)

Command Modes

  • /exec

terminal edit-mode vi

[no] terminal edit-mode vi [persist]

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
edit-mode

set command line edition keys (vi or emacs; emacs is default)
vi

edit like in vi; by default in insert-mode, use ~ for command-mode
persist

add command to <username>.rc.cli file (auto-execed at login time)

Command Modes

  • /exec

terminal event-manager bypass

terminal [noarg] event-manager bypass

Syntax Description

terminal

Set terminal line parameters
noarg
no  value: 1
Negate a command or set its defaults
event-manager

Event manager cli event
bypass

Bypass event manager cli event publish

Command Modes

  • /exec

terminal history no-exec-in-config (clic)

[no] terminal history no-exec-in-config

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
history

configure terminal history properties
no-exec-in-config

don't recall exec commands while in config mode

Command Modes

  • /exec

terminal history no-exec-in-config (clic)

[no] terminal history no-exec-in-config

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
history

configure terminal history properties
no-exec-in-config

don't recall exec commands while in config mode

Command Modes

  • /exec

terminal history no-exec-in-config (clic)

[no] terminal history no-exec-in-config

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
history

configure terminal history properties
no-exec-in-config

don't recall exec commands while in config mode

Command Modes

  • /exec

terminal length (vsh)

terminal length i0

Syntax Description

terminal

Set terminal line parameters
length

Set number of lines on a screen
i0

Type: uinteger

min: 0  max: 511  

Number of lines on screen (0 for no pausing)

Command Modes

  • /exec/configure/console

terminal length (vsh)

terminal length i0

Syntax Description

terminal

Set terminal line parameters
length

Set number of lines on a screen
i0

Type: uinteger

min: 0  max: 511  

Number of lines on screen (0 for no pausing)

Command Modes

  • /exec

terminal lock

terminal lock

Syntax Description

terminal

Set terminal line parameters
lock

Locks the CLI Config mode

Command Modes

  • /exec

terminal log-all

[noarg] terminal log-all

Syntax Description

terminal

Configure terminal settings
noarg
no  value: 1
Negate a command or set its defaults
log-all

Accounting log all commands including the show commands

Command Modes

  • /exec/configure

terminal no

terminal no { length | terminal-type | width }

Syntax Description

terminal

Set terminal line parameters
no

Negate a command or set its defaults
length

Set number of lines on a screen
terminal-type

Set the terminal type
width

Set width of the display terminal

Command Modes

  • /exec

terminal output xml

[no] terminal output xml

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
output

how output of show commands should be formated
xml

xml output

Command Modes

  • /exec

terminal password

terminal password password | no terminal password [password]

Syntax Description

no

Negate a command or set its defaults
terminal

Set terminal line parameters
password

set a password to be used in copy scp/ftp commands; use online help on the argument to disable echo so you don't need to type control-x-e twice (to toggle echo), echo will be re-enabled after carriage-return

password

Type: userdef

Enter the password (online help that you just did disabled echo so type your password and press return

Command Modes

  • /exec

terminal redirection-mode

terminal redirection-mode mode

Syntax Description

terminal

Set terminal line parameters
redirection-mode

Set the redirection mode
mode
ascii  value: 0
Set the redirection mode to ASCII
zipped  value: 1
Set the redirection mode to ZIPPED

Command Modes

  • /exec

terminal reset-role

terminal reset-role num

Syntax Description

terminal

Set terminal line parameters
reset-role

Reset the privilege role to default
num

Type: integer

min: 0  max: 15  

Enter the role num

Command Modes

  • /exec

terminal reset vlan-config-mutex

terminal reset vlan-config-mutex

Syntax Description

terminal

Set terminal line parameters
reset

Force reset of the vlan config mode mutex
vlan-config-mutex

Vlan configuration mutex

Command Modes

  • /exec

terminal session-timeout

terminal session-timeout i0

Syntax Description

terminal

Set terminal line parameters
session-timeout

Set session timeout
i0

Type: uinteger

min: 0  max: 525600  

Enter timeout in minutes, 0 to disable

Command Modes

  • /exec

terminal sticky-mode

terminal [noarg] sticky-mode

Syntax Description

terminal

Set terminal line parameters
noarg
no  value: 1
Negate a command or set its defaults
sticky-mode

Search for the command match in current mode only

Command Modes

  • /exec

terminal terminal-type

terminal terminal-type s0

Syntax Description

terminal

Set terminal line parameters
terminal-type

Set the terminal type
s0

Type: string

Terminal type

Command Modes

  • /exec

terminal tree-update

terminal tree-update

Syntax Description

terminal

Set terminal line parameters
tree-update

Updates the main parse tree

Command Modes

  • /exec

terminal unlock

terminal unlock

Syntax Description

terminal

Set terminal line parameters
unlock

Force unlocking of the CLI config mode

Command Modes

  • /exec

terminal verify-only

terminal [noarg] verify-only [ username user ]

Syntax Description

terminal

Set terminal line parameters
noarg
no  value: 1
Negate a command or set its defaults
verify-only

Verify command and do not execute
username

Username for aaa authorization
user

Type: string

length: 32

Username for aaa authorization

Command Modes

  • /exec

terminal width (vsh)

terminal width i0

Syntax Description

terminal

Set terminal line parameters
width

Set width of the display terminal
i0

Type: integer

min: 24  max: 511  

Number of characters on a screen line

Command Modes

  • /exec/configure/console

terminal width (vsh)

terminal width i0

Syntax Description

terminal

Set terminal line parameters
width

Set width of the display terminal
i0

Type: integer

min: 24  max: 511  

Number of characters on a screen line

Command Modes

  • /exec

threshold-percent

(explicit id )

Syntax Description

no

Negate a command or set its defaults
threshold-percent

Threshold parameters
percent-threshold

Percentage threshold
percentup

Up threshold
up-percentage

Type: integer

min: 0  max: 100  

Up threshold percentage
percentdown

Down threshold
down-percentage

Type: integer

min: 0  max: 100  

Down threshold percentage

Command Modes

  • /exec/configure/tr-list-thrp

time-range

[no] time-range name

Syntax Description

no

Negate a command or set its defaults
time-range

Define time range entries
name

Type: string

length: 64

Time range name

Command Modes

  • /exec/configure

time daily

time { daily s0 | monthly s1 | start { now repeat s2 | s3 [ repeat s4 ] } | weekly s5 } | no time [ daily s0 | monthly s1 | start { now repeat s2 | s3 [ repeat s4 ] } | weekly s5 ]

Syntax Description

no

Negate a command or set its defaults
time

Specify a schedule to run jobs
daily

Specify a daily schedule
s0

Type: string

length: 5

[HH:]MM
monthly

Specify a monthly schedule
s1

Type: string

length: 8

Day-of-month {[[dm:]HH:]MM} dm = 1 .. 31
start

Specify a future time schedule
now

Start-time = 2 minutes from `now'
repeat

Specify an interval
s2

Type: string

length: 8

Interval {[[dd:]HH:]MM} dd,HH,MM are +ve integers
s3

Type: string

length: 18

Start-time {[[[[yyyy:]mmm:]dd:]HH]:MM | +[[dd:]HH:]MM}
repeat

Specify an interval
s4

Type: string

length: 8

Interval {[[dd:]HH:]MM} dd,HH,MM are +ve integers
weekly

Specify a weekly schedule
s5

Type: string

length: 10

Day-of-week {[[dow:]HH:]MM} dow = 1 (Sun) .. 7 (Sat)

Command Modes

  • /exec/configure/schedule

timers (eigrp)

[no] timers { nsf { route-hold hold-interval | converge converge-interval | signal signal-interval } | active-time [ max-active-time | disabled ] }

Syntax Description

no

Negate a command or set its defaults
timers

Set EIGRP timers
nsf

EIGRP NSF timer
route-hold

EIGRP hold time for routes learned from nsf peer
hold-interval

Type: integer

min: 20  max: 300  default: 240

Seconds
active-time

EIGRP time limit for active state
max-active-time

Type: integer

min: 1  max: 0  default: 3

EIGRP active-state time limit in minutes
disabled

disable EIGRP time limit for active state
converge

EIGRP time limit for convergence after switchover
converge-interval

Type: integer

min: 60  max: 180  default: 120

Seconds
signal

EIGRP time limit for signaling NSF restart
signal-interval

Type: integer

min: 10  max: 360  default: 20

Seconds

Command Modes

  • /exec/configure/router-eigrp/router-eigrp-vrf-common
  • /exec/configure/router-eigrp/router-eigrp-af-common

timers (glbp)

timers { hello-time { hold-time | ms-hold hold-time-msec } | ms-hello hello-time-msec { hold-time-sec | msec-hold hold-time-msec } | redirect redirect-time sec-hold-time } | no timers [ hello-time [ hold-time | ms-hold hold-time-msec ] | ms-hello [ hello-time-msec [ hold-time-sec | msec-hold hold-time-msec ] ] | redirect [ redirect-time [sec-hold-time] ] ]

Syntax Description

no

Negate a command or set its defaults
timers

Adjust GLBP timers
hello-time

Type: integer

min: 1  max: 60  

Specify Hello interval in seconds
hold-time

Type: integer

min: 2  max: 180  

Specify Hold time in seconds
ms-hold

Specify hold time in milliseconds
hold-time-msec

Type: integer

min: 1020  max: 180000  

Hold time in milliseconds
ms-hello

Specify hello interval in milliseconds
hello-time-msec

Type: integer

min: 250  max: 60000  

hello interval in milliseconds
hold-time-sec

Type: integer

min: 2  max: 180  

Hold time in seconds
msec-hold

Specify hold time in milliseconds
redirect

Specify time-out value for failed forwarders
redirect-time

Type: integer

min: 0  max: 3600  

Interval in seconds to redirect to failed forwarders
sec-hold-time

Type: integer

min: 610  max: 64800  

Time-out interval in seconds for failed forwarders

Command Modes

  • /exec/configure/if-eth-any/glbp

timers (hsrp_engine)

timers { hello-time { hold-time | msec-hold msec-hold } | msec-hello msec-hello { hold-time | msec-hold msec-hold } } | no timers

Syntax Description

no

Negate a command or set its defaults
timers

Hello and hold timers
hello-time

Type: integer

min: 1  max: 254  

Hello interval in seconds
hold-time

Type: integer

min: 3  max: 255  

Hold time in seconds
msec-hold

Specify hold interval in milliseconds
msec-hold

Type: integer

min: 750  max: 3000  

Hold interval in milliseconds
msec-hello

Specify hello interval in milliseconds
msec-hello

Type: integer

min: 250  max: 999  

Hello interval in milliseconds

Command Modes

  • /exec/configure/if-eth-any/hsrp_ipv4
  • /exec/configure/if-eth-any/hsrp_ipv6

timers basic

timers basic update invalid holddown garbage | no timers basic [ update invalid holddown garbage ]

Syntax Description

no

Negate a command or set its defaults
timers

RIP set timers
basic

RIP set basic timers
update

Type: uinteger

min: 5  max: 4294967295  default: 30

RIP update period
invalid

Type: uinteger

min: 1  max: 4294967295  default: 180

RIP route timeout period
holddown

Type: uinteger

min: 0  max: 4294967295  default: 180

RIP route holddown period
garbage

Type: uinteger

min: 1  max: 4294967295  default: 120

RIP route garbage period

Command Modes

  • /exec/configure/router-rip/router-rip-af-common
  • /exec/configure/router-rip/router-rip-vrf-af-common

timers bestpath-defer maximum

[no] timers bestpath-defer bestpath-defer-time maximum bestpath-defer-time-max

Syntax Description

no

Negate a command or set its defaults
timers

Configure bgp related timers
bestpath-defer

Configure bestpath defer timer value for batch prefix processing
bestpath-defer-time

Type: integer

min: 0  max: 30  

Bestpath defer time (seconds)
maximum

Configure bestpath defer timer maximum value
bestpath-defer-time-max

Type: integer

min: 0  max: 300  

Maximum bestpath defer time (seconds)

Command Modes

  • /exec/configure/router-bgp/router-bgp-af

timers bestpath-limit

timers bestpath-limit bestpath-timeout [always] | no timers bestpath-limit [bestpath-timeout]

Syntax Description

no

Negate a command or set its defaults
timers

Configure bgp related timers
bestpath-limit

Configure timeout for first bestpath after restart
bestpath-timeout

Type: integer

min: 1  max: 3600  default: 300

Bestpath timeout (seconds)
always

Configure update-delay-always option

Command Modes

  • /exec/configure/router-bgp/vrf-cmds

timers bgp

[no] timers bgp keepalive-interval hold-time

Syntax Description

no

Negate a command or set its defaults
timers

Configure bgp related timers
bgp

Configure different bgp keepalive and holdtimes
keepalive-interval

Type: integer

min: 0  max: 3600  default: 60

Keepalive interval (seconds)
hold-time

Type: integer

min: 0  max: 3600  default: 180

Holdtime (seconds)

Command Modes

  • /exec/configure/router-bgp/vrf-cmds

timers lsa-arrival (ospf)

timers lsa-arrival interval | no timers lsa-arrival [interval]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
lsa-arrival

Mimimum interval between arrival of a LSA
interval

Type: integer

min: 10  max: 600000  default: 1000

Interval value (milliseconds)

Command Modes

  • /exec/configure/router-ospf
  • /exec/configure/router-ospf/vrf

timers lsa-arrival (ospfv3)

timers lsa-arrival interval | no timers lsa-arrival [interval]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
lsa-arrival

Mimimum interval between arrival of a LSA
interval

Type: integer

min: 10  max: 600000  default: 1000

Interval value (millisecond)

Command Modes

  • /exec/configure/router-ospf3
  • /exec/configure/router-ospf3/vrf

timers lsa-group-pacing (ospf)

timers lsa-group-pacing interval | no timers lsa-group-pacing [interval]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
lsa-group-pacing

LSA group refresh/maxage interval
interval

Type: integer

min: 1  max: 1800  

Interval value (seconds)

Command Modes

  • /exec/configure/router-ospf
  • /exec/configure/router-ospf/vrf

timers lsa-group-pacing (ospfv3)

timers lsa-group-pacing interval | no timers lsa-group-pacing [interval]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
lsa-group-pacing

LSA group refresh/maxage interval
interval

Type: integer

min: 1  max: 1800  

Interval value (seconds)

Command Modes

  • /exec/configure/router-ospf3
  • /exec/configure/router-ospf3/vrf

timers prefix-peer-timeout

timers prefix-peer-timeout prefixpeer-timeout | no timers prefix-peer-timeout [prefixpeer-timeout]

Syntax Description

no

Negate a command or set its defaults
timers

Configure bgp related timers
prefix-peer-timeout

Configure how long state for a prefix peer is maintained
prefixpeer-timeout

Type: integer

min: 0  max: 1200  default: 30

Prefix Peer timeout (seconds)

Command Modes

  • /exec/configure/router-bgp/vrf-cmds

timers throttle lsa (ospf)

timers throttle lsa start-time hold-time max-time | no timers throttle lsa [ start-time hold-time max-time ]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
throttle

Set rate-limiting values (milliseconds)
lsa

Set rate-limiting for LSA generation
start-time

Type: integer

min: 0  max: 5000  default: 0

Start interval (milliseconds)
hold-time

Type: integer

min: 50  max: 30000  default: 5000

Hold interval (milliseconds)
max-time

Type: integer

min: 50  max: 30000  default: 5000

Max interval (milliseconds)

Command Modes

  • /exec/configure/router-ospf
  • /exec/configure/router-ospf/vrf

timers throttle lsa (ospfv3)

timers throttle lsa start-time hold-time max-time | no timers throttle lsa [ start-time hold-time max-time ]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
throttle

Set rate-limiting values (milliseconds)
lsa

Set rate-limiting for LSA generation
start-time

Type: integer

min: 0  max: 5000  default: 0

Start interval (milliseconds)
hold-time

Type: integer

min: 50  max: 30000  default: 5000

Hold interval (milliseconds)
max-time

Type: integer

min: 50  max: 30000  default: 5000

Max interval (milliseconds)

Command Modes

  • /exec/configure/router-ospf3
  • /exec/configure/router-ospf3/vrf

timers throttle spf (ospf)

timers throttle spf start-time hold-time max-time | no timers throttle spf [ start-time hold-time max-time ]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
throttle

Configure timer related constants
spf

OSPF SPF timers
start-time

Type: integer

min: 1  max: 600000  default: 200

Initial SPF schedule delay in milliseconds
hold-time

Type: integer

min: 1  max: 600000  default: 1000

Minimum hold time between SPF calculations
max-time

Type: integer

min: 1  max: 600000  default: 5000

Maximum wait time between SPF calculations

Command Modes

  • /exec/configure/router-ospf
  • /exec/configure/router-ospf/vrf

timers throttle spf (ospfv3)

timers throttle spf start-time hold-time max-time | no timers throttle spf [ start-time hold-time max-time ]

Syntax Description

no

Negate a command or set its defaults
timers

Configure timer related constants
throttle

Configure timer related constants
spf

OSPF SPF timers
start-time

Type: integer

min: 1  max: 600000  default: 200

Initial SPF schedule delay in milliseconds
hold-time

Type: integer

min: 1  max: 600000  default: 1000

Minimum hold time between SPF calculations
max-time

Type: integer

min: 1  max: 600000  default: 5000

Maximum wait time between SPF calculations

Command Modes

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6
  • /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

timerstimers

timers keepalive-interval hold-time | { no | default } timers [ keepalive-interval hold-time ]

Syntax Description

no

Negate a command or set its defaults
default

Inherit values from a peer template
timers

Configure keepalive and hold timers
keepalive-interval

Type: integer

min: 0  max: 3600  default: 60

Keepalive interval (seconds)
hold-time

Type: integer

min: 0  max: 3600  default: 180

Holdtime (seconds)

Command Modes

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

tr

" | " tr [ -c | -d | -s | -t ] + SET1 [SET2]

Syntax Description

|

Pipe command output to filter
tr

Translate, squeeze, and/or delete characters
-c

first complement SET1
-d

delete characters in SET1, do not translate
-s

replace each sequence of a repeated character from SET1 with single occurrence of that character
-t

first truncate SET1 to length of SET2
SET1

Type: string

character SET1: CHAR1-CHAR2 = all characters from CHAR1 to CHAR2 in ascending order; special chars: \t (tab) \n (new line) [:alnum:] [:alpha:] [:digit:] [:graph:] (printable, no space) [:print:] (printable, with space) [:lower:] [:upper:] [:space:] (tab or space)

SET2

Type: string

character SET2 (for translation; length is extended to length of SET1 by repeating last char, excess chars are ignored): format same as SET1; [CHAR*] = copies of CHAR until length of SET1; [CHAR*REPEAT] = REPEAT copies of CHAR

Command Modes

  • /output

traceroute

traceroute { alpha | numeric } [ source { alpha | numeric | interface } ] [ vrf { vrf-name | vrf-known-name } ]

Syntax Description

numeric

Type: ipaddr

IP address of remote system
source

Set source address in IP header
vrf

Display per-VRF information
vrf-name

Type: vrf

pattern: [-a-zA-Z0-9_:;$#@]*

antipattern: vrf | detail | interface | definition | context | forwarding | member | all | l2-vrf | topology | passive

length: 32

VRF name
vrf-known-name

Type: vrf

Known VRF name

Command Modes

  • /exec

traceroute6

traceroute6 { host | hostname } [ source { host | hostname | interface } ] [ vrf { vrf-name | vrf-known-name } ]

Syntax Description

host

Type: ipv6addr

IPv6 address format: aaaa:bbbb:cccc:dddd:eeee:ffff:gggg:hhhh, aaaa::bbbb
hostname

Type: string

Hostname of remote system
source

Set source address in IPv6 header
vrf

Display per-VRF information
vrf-name

Type: vrf

pattern: [-a-zA-Z0-9_:;$#@]*

antipattern: vrf | detail | interface | definition | context | forwarding | member | all | l2-vrf | topology | passive

length: 32

VRF name
vrf-known-name

Type: vrf

Known VRF name

Command Modes

  • /exec

track (hsrp_engine)

[no] track object-number [ decrement value ]

Syntax Description

no

Negate a command or set its defaults
track

Associates track object to HSRP group
object-number

Type: integer

min: 1  max: 500  

Set the object number to the group
decrement

Decrements when tracked object goes down
value

Type: integer

min: 1  max: 255  

Set the value to decrement from priority

Command Modes

  • /exec/configure/if-eth-any/hsrp_ipv4
  • /exec/configure/if-eth-any/hsrp_ipv6

track (mcecm)

track track-obj | no track track-obj

Syntax Description

no

Negate a command or set its defaults
track

Tracking object to suspend vPC if object goes down
track-obj

Type: integer

min: 1  max: 500  

Tracked object

Command Modes

  • /exec/configure/vpc-domain

track (otm)

track object-id [ interface ifnum { line-protocol | ipv4 routing | ipv6 routingv6 } | { ip_v4 route route-prefix | ip_v6 routev6 v6route-prefix } reachability | list boolean bool-val | list threshold threshold-val ] | no track object-id [force]

Syntax Description

no

Negate a command or set its defaults
track

Object tracking configuration commands
object-id

Type: uinteger

min: 1  max: 500  

Tracked Object
interface

Interface to track
ifnum

Type: interface

Interface type and number
line-protocol

Track interface line-protocol
ipv4

IPv4 parameters
routing

Track interface ipv4 routing
ipv6

IPv6 parameters
routingv6

Track interface ipv6 routing
ip_v4

IPv4 protocol
route

IPv4 route
route-prefix

Type: ipprefix

Specify ipv4 route prefix
ip_v6

IPv6 protocol
routev6

IPv6 route
v6route-prefix

Type: ipv6prefix

Specify ipv6 route prefix
reachability

Route reachability state
force

Completely remove the object
list

Object tracking list
boolean

boolean list type
bool-val

boolean list type

and  value: 0
List is TRUE if all Objects are TRUE
or  value: 1
List is TRUE if any Object is TRUE
threshold

threshold type
threshold-val

threshold type

weight  value: 3
Thresholds described by weight values
percentage  value: 4
Thresholds described as a percentage of total

Command Modes

  • /exec/configure

track interface

track { interface intf_num priority priority_value | object-num [ decrement decrement-value ] } | no track [ interface intf_num priority priority_value | object-num [ decrement decrement-value ] ]

Syntax Description

no

Negate a command or set its defaults
track

Track the availability of another interface/object
interface

Select the tracked interface(Native tracking)
intf_num

Type: interface
priority

Vr priority used when the tracked interface is down
priority_value

Type: integer

min: 1  max: 254  
object-num

Type: integer

min: 1  max: 500  

Set the object number to the group(Object tracking)
decrement

Decrements priority when tracked object goes down
decrement-value

Type: integer

min: 1  max: 254  

Set the value to decrement from priority

Command Modes

  • /exec/configure/if-eth-any/vrrp

traffic-share

[no] traffic-share { balanced | min across-interfaces }

Syntax Description

no

Negate a command or set its defaults
traffic-share

How to compute traffic share over alternate paths
balanced

Share inversely proportional to metric
min

All traffic shared among min metric paths
across-interfaces

Use different interfaces for equal-cost paths

Command Modes

  • /exec/configure/router-eigrp/router-eigrp-vrf-common
  • /exec/configure/router-eigrp/router-eigrp-af-common

transmit-delay (ospf)

transmit-delay delay | no transmit-delay [delay]

Syntax Description

no

Negate a command or set its defaults
transmit-delay

Packet transmission delay
delay

Type: integer

min: 1  max: 450  default: 1

(seconds)

Command Modes

  • /exec/configure/router-ospf/vrf/router-ospf-slink

transmit-delay (ospf)

transmit-delay delay | no transmit-delay [delay]

Syntax Description

no

Negate a command or set its defaults
transmit-delay

Packet transmission delay
delay

Type: integer

min: 1  max: 450  default: 1

(seconds)

Command Modes

  • /exec/configure/router-ospf/router-ospf-vlink
  • /exec/configure/router-ospf/vrf/router-ospf-vlink

transmit-delay (ospfv3)

transmit-delay delay | no transmit-delay [delay]

Syntax Description

no

Negate a command or set its defaults
transmit-delay

Packet transmission delay
delay

Type: integer

min: 1  max: 450  default: 1

(seconds)

Command Modes

  • /exec/configure/router-ospf3/router-ospf3-vlink
  • /exec/configure/router-ospf3/vrf/router-ospf3-vlink

transport connection-mode passive

[ no | default ] transport connection-mode passive

Syntax Description

no

Negate a command or set its defaults
default

Inherit values from a peer template
transport

BGP transport connection
connection-mode

Specify type of connection
passive

Allow passive connection setup only

Command Modes

  • /exec/configure/router-bgp/router-bgp-neighbor
  • /exec/configure/router-bgp/router-bgp-neighbor-stmp
  • /exec/configure/router-bgp/router-bgp-vrf-neighbor
  • /exec/configure/router-bgp/router-bgp-template-neighbor

transport email from

transport email { from s0 | reply-to s1 | smtp-server { hostipv4 | hostipv6 | hostname } [ port i1 ] [ use-vrf s2 ] } | no transport email smtp-server | no transport email { from | reply-to }

Syntax Description

no

Negate a command or set its defaults
transport

Configure transport related configuration
email

Configure email transport related configuration
from

Configure from email address
s0

Type: string

length: 255

Provide from email address, example: SJ-9500-1@xyz.com
reply-to

Configure replyto email address
s1

Type: string

length: 255

Provide reply-to email address, example: admin@xyz.com
smtp-server

Configure SMTP server address
hostname

Type: string

SMTP server(DNS name or IPv4 or IPv6 address)
hostipv4

Type: ipaddr

IPV4 address of SMTP server
hostipv6

Type: ipv6addr

IPV6 address of SMTP server
port

Configure SMTP server port (default:25)
i1

Type: integer

min: 1  max: 65535  

SMTP server port
use-vrf

Configure vrf name
s2

Type: string

length: 32

vrf name

Command Modes

  • /exec/configure/callhome

transport email mail-server

[no] transport email mail-server { hostipv4 | hostipv6 | hostname } [ port i1 ] [ priority i2 ] [ use-vrf s2 ]

Syntax Description

no

Negate a command or set its defaults
transport

Configure transport related configuration
email

Configure email transport related configuration
mail-server

Configure SMTP server address (for supporting multiple SMTP-servers)
hostname

Type: string

SMTP server(DNS name or IPv4 or IPv6 address)
hostipv4

Type: ipaddr

IPV4 address of SMTP server
hostipv6

Type: ipv6addr

IPV6 address of SMTP server
port

Configure SMTP server port (default:25)
i1

Type: integer

min: 1  max: 65535  

SMTP server port
use-vrf

Configure vrf name
s2

Type: string

length: 32

vrf name
priority

Configure SMTP server priority (1-100) (default:50)
i2

Type: integer

min: 1  max: 100  

SMTP server priority

Command Modes

  • /exec/configure/callhome

transport http proxy enable

[no] transport http proxy enable

Syntax Description

no

Negate a command or set its defaults
transport

Configure transport related configuration
http

Configure transport option for http urls
proxy

Configure proxy for http transport
enable

Enable the usage of proxy server for messages sent over http(s)

Command Modes

  • /exec/configure/callhome

transport http proxy server

transport http proxy server hostname [ port i1 ] | no transport http proxy server

Syntax Description

no

Negate a command or set its defaults
transport

Configure transport related configuration
http

Configure transport option for http urls
proxy

Configure proxy for http transport
server

Configure proxy server address and port
hostname

Type: nameorip

Proxy server name or IP address(DNS name or IPv4 or IPv6 address)
port

Configure Proxy server port (default:8080)
i1

Type: integer

min: 1  max: 65535  

Proxy server port

Command Modes

  • /exec/configure/callhome

transport http use-vrf

transport http use-vrf s2 | no transport http use-vrf

Syntax Description

no

Negate a command or set its defaults
transport

Configure transport related configuration
http

Configure transport option for http urls
use-vrf

Configure vrf name
s2

Type: string

length: 32

vrf name

Command Modes

  • /exec/configure/callhome

transport type

[no] transport type { tcp [ port tportnum ] [ access-class aclname ] | tls [ disable-remotecert-validation [ localcert localtp [ port tportnum [ access-class aclname ] | access-class aclname [ port tportnum ] ] | port tportnum [ localcert localtp [ access-class aclname ] | access-class aclname [ localcert localtp ] ] | access-class aclname [ localcert localtp [ port tportnum ] | port tportnum [ localcert localtp ] ] ] | localcert localtp [ disable-remotecert-validation [ port tportnum [ access-class aclname ] | access-class aclname [ port tportnum ] ] | port tportnum [ disable-remotecert-validation [ access-class aclname ] | access-class aclname [disable-remotecert-validation] ] | access-class aclname [ disable-remotecert-validation [ port tportnum ] | port tportnum [disable-remotecert-validation] ] ] | port tportnum [ disable-remotecert-validation [ localcert localtp [ access-class aclname ] | access-class aclname [ localcert localtp ] ] | localcert localtp [ disable-remotecert-validation [ access-class aclname ] | access-class aclname [disable-remotecert-validation] ] | access-class aclname [ disable-remotecert-validation [ localcert localtp ] | localcert localtp [disable-remotecert-validation] ] ] | access-class aclname [ disable-remotecert-validation [ localcert localtp [ port tportnum ] | port tportnum [ localcert localtp ] ] | localcert localtp [ disable-remotecert-validation [ port tportnum ] | port tportnum [disable-remotecert-validation] ] | port tportnum [ disable-remotecert-validation [ localcert localtp ] | localcert localtp [disable-remotecert-validation] ] ] | remotecert remotetp [ localcert localtp [ port tportnum [ access-class aclname ] | access-class aclname [ port tportnum ] ] | port tportnum [ localcert localtp [ access-class aclname ] | access-class aclname [ localcert localtp ] ] | access-class aclname [ localcert localtp [ port tportnum ] | port tportnum [ localcert localtp ] ] ] | localcert localtp [ remotecert remotetp [ port tportnum [ access-class aclname ] | access-class aclname [ port tportnum ] ] | port tportnum [ remotecert remotetp [ access-class aclname ] | access-class aclname [ remotecert remotetp ] ] | access-class aclname [ remotecert remotetp [ port tportnum ] | port tportnum [ remotecert remotetp ] ] ] | port tportnum [ remotecert remotetp [ localcert localtp [ access-class aclname ] | access-class aclname [ localcert localtp ] ] | localcert localtp [ remotecert remotetp [ access-class aclname ] | access-class aclname [ remotecert remotetp ] ] | access-class aclname [ remotecert remotetp [ localcert localtp ] | localcert localtp [ remotecert remotetp ] ] ] | access-class aclname [ remotecert remotetp [ localcert localtp [ port tportnum ] | port tportnum [ localcert localtp ] ] | localcert localtp [ remotecert remotetp [ port tportnum ] | port tportnum [ remotecert remotetp ] ] | port tportnum [ remotecert remotetp [ localcert localtp ] | localcert localtp [ remotecert remotetp ] ] ] ] }

Syntax Description

no

Negate a command or set its defaults
transport

Transport command
type

Session transport
tcp

TCP transport Not available in this release.
tls

TLS transport
disable-remotecert-validation

Disable Remote Certificate Validation
localcert

Local Certificate
localtp

Type: string

Local Trust Point Name
remotecert

Remote Certificate Validation
remotetp

Type: string

Remote Trust Point Name
port

Port number
tportnum

Type: uinteger

min: 1025  max: 65535  

Number
access-class

Filter incoming connections based on IP access list
aclname

Type: string

IP access list name

Command Modes

  • /exec/configure/onep

trap bfd session-down

trap bfd session-down startIndex startIndex-key endIndex endIndex-key

Syntax Description

trap

snmp trap
bfd

BFD commands
session-down

Sesssion going DOWN
startIndex

Session diagnostic code

noDiagnostic  value: 1
noDiagnostic
controlDetectionTimeExpired  value: 2
controlDetectionTimeExpired
echoFunctionFailed  value: 3
echoFunctionFailed
neighborSignaledSessionDown  value: 4
neighborSignaledSessionDown
forwardingPlaneReset  value: 5
forwardingPlaneReset
pathDown  value: 6
pathDown
concatenatedPathDown  value: 7
concatenatedPathDown
administrativelyDown  value: 8
administrativelyDown
reverseConcatenatedPathDown  value: 9
reverseConcatenatedPathDown
startIndex-key

Type: uinteger

help
endIndex

Session diagnostic code

noDiagnostic  value: 1
noDiagnostic
controlDetectionTimeExpired  value: 2
controlDetectionTimeExpired
echoFunctionFailed  value: 3
echoFunctionFailed
neighborSignaledSessionDown  value: 4
neighborSignaledSessionDown
forwardingPlaneReset  value: 5
forwardingPlaneReset
pathDown  value: 6
pathDown
concatenatedPathDown  value: 7
concatenatedPathDown
administrativelyDown  value: 8
administrativelyDown
reverseConcatenatedPathDown  value: 9
reverseConcatenatedPathDown
endIndex-key

Type: uinteger

help

Command Modes

  • /exec

trap bfd session-up

trap bfd session-up startIndex startIndex-key endIndex endIndex-key

Syntax Description

trap

snmp trap
bfd

BFD commands
session-up

Sesssion going UP
startIndex

Session diagnostic code

noDiagnostic  value: 1
noDiagnostic
controlDetectionTimeExpired  value: 2
controlDetectionTimeExpired
echoFunctionFailed  value: 3
echoFunctionFailed
neighborSignaledSessionDown  value: 4
neighborSignaledSessionDown
forwardingPlaneReset  value: 5
forwardingPlaneReset
pathDown  value: 6
pathDown
concatenatedPathDown  value: 7
concatenatedPathDown
administrativelyDown  value: 8
administrativelyDown
reverseConcatenatedPathDown  value: 9
reverseConcatenatedPathDown
startIndex-key

Type: uinteger

help
endIndex

Session diagnostic code

noDiagnostic  value: 1
noDiagnostic
controlDetectionTimeExpired  value: 2
controlDetectionTimeExpired
echoFunctionFailed  value: 3
echoFunctionFailed
neighborSignaledSessionDown  value: 4
neighborSignaledSessionDown
forwardingPlaneReset  value: 5
forwardingPlaneReset
pathDown  value: 6
pathDown
concatenatedPathDown  value: 7
concatenatedPathDown
administrativelyDown  value: 8
administrativelyDown
reverseConcatenatedPathDown  value: 9
reverseConcatenatedPathDown
endIndex-key

Type: uinteger

help

Command Modes

  • /exec

trap lldp lldpRemTablesChange

trap lldp lldpRemTablesChange lldpStatsRemTablesInserts lldpStatsRemTablesDeletes lldpStatsRemTablesDrops lldpStatsRemTablesAgeouts

Syntax Description

trap

snmp trap
lldp

lldp trap
lldpRemTablesChange

lldp remote table change trap
lldpStatsRemTablesInserts

Type: uinteger

lldp remote table inserts
lldpStatsRemTablesDeletes

Type: uinteger

lldp remote table deletes
lldpStatsRemTablesDrops

Type: uinteger

lldp remote table drops
lldpStatsRemTablesAgeouts

Type: uinteger

lldp remote table ageouts

Command Modes

  • /exec

trap pim pimNeighborLoss

trap pim pimNeighborLoss pimNeighborIfIndex pimNeighborAddress-in

Syntax Description

trap

Generate traps from cli
pim

PIM global configuration commands
pimNeighborLoss

pim trap for pimNeighborLoss
pimNeighborIfIndex

Type: integer

Neighbor ifindex
pimNeighborAddress-in

Type: ipaddr

Neighbor Address

Command Modes

  • /exec

trigger forwarding distribution module

trigger forwarding distribution module module

Syntax Description

trigger

Trigger
forwarding

Trigger related to forwarding
distribution

Trigger distribution of forwarding data to LCs
module

distribute to a particular module
module

Type: integer

module number

Command Modes

  • /exec

trigger route download vrf

trigger route download vrf vrf-name { ipv4 route4 | ipv6 route6 } [ module slot-num ]

Syntax Description

trigger

Trigger
route

IP route related
download

Download
vrf

vrf
vrf-name

Type: string

vrf name
ipv4

ipv4
route4

Type: ipprefix

ipv4 prefix
ipv6

ipv6
route6

Type: ipv6prefix

ipv6 prefix
module

Module
slot-num

Type: integer

Slot number of the module

Command Modes

  • /exec

tunnel destination

tunnel destination { host-name | ip-addr | ipv6-addr } | no tunnel destination [ host-name | ip-addr | ipv6-addr ]

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
destination

destination of tunnel packets
host-name

Type: string

host name
ip-addr

Type: ipaddr

IPv4 address (A.B.C.D)
ipv6-addr

Type: ipv6addr

IPv6 address

Command Modes

  • /exec/configure/if-gre-tunnel

tunnel mode gre

tunnel mode gre [ ip | ipv6 ] | no tunnel mode

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
mode

tunnel encapsulation method
gre

generic route encapsulation protocol
ip

over IP
ipv6

over IPv6

Command Modes

  • /exec/configure/if-any-tunnel

tunnel path-mtu-discovery (tm)

tunnel path-mtu-discovery { age-timer [ age-time | infinite ] | min-mtu mtu } | no tunnel path-mtu-discovery { age-timer [ age-time | infinite ] | min-mtu mtu }

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
path-mtu-discovery

Enable Path MTU Discovery on tunnel
age-timer

Set PMTUD aging timer
age-time

Type: integer

min: 10  max: 30  

Aging time
infinite

Disable pathmtu aging timer
min-mtu

Min pmtud mtu allowed
mtu

Type: integer

min: 64  max: 65535  

Bytes

Command Modes

  • /exec/configure/if-any-tunnel

tunnel path-mtu-discovery (tm)

[no] tunnel path-mtu-discovery

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
path-mtu-discovery

Enable Path MTU Discovery on tunnel

Command Modes

  • /exec/configure/if-any-tunnel

tunnel source

tunnel source { intf | ip-addr | ipv6-addr } | no tunnel source [ intf | ip-addr | ipv6-addr ]

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
source

source of tunnel packets
intf

Type: interface

interface
ip-addr

Type: ipaddr

IPv4 address (A.B.C.D)
ipv6-addr

Type: ipv6addr

IPv6 address

Command Modes

  • /exec/configure/if-gre-tunnel

tunnel ttl

tunnel ttl ttl_val | no tunnel ttl [ttl_val]

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
ttl

set time to live
ttl_val

Type: integer

min: 1  max: 255  

time to line value

Command Modes

  • /exec/configure/if-any-tunnel

tunnel use-vrf

tunnel use-vrf { vrf-name | vrf-known-name } | no tunnel use-vrf [ vrf-name | vrf-known-name ]

Syntax Description

no

Negate a command or set its defaults
tunnel

protocol-over-protocol tunneling
use-vrf

set tunnel vrf membership
vrf-name

Type: vrf

pattern: [-a-zA-Z0-9_:;$#@]*

antipattern: vrf | detail | interface | definition | context | forwarding | member | all | l2-vrf | topology | passive

length: 32

VRF name
vrf-known-name

Type: vrf

Known VRF name

Command Modes

  • /exec/configure/if-any-tunnel

typetype

type fextype | type swcardid | no type

Syntax Description

no

Negate the command
type

FEX Card type
fextype

Fex Type

N2248T  value: 99
Fabric Extender 48x1G 4x10G Module
N2232P  value: 82
Fabric Extender 32x10G 8x10G Module
N2224TP  value: 132
Fabric Extender 24x1G 2x10G SFP+ Module
N2232TM  value: 164
Fabric Extender 32x10GBase-T 8x10G SFP+ Module
N2248TP-E  value: 149
Fabric Extender 48x1G 4x10G SFP+ Module
swcardid

Type: string

length: 30

Card type

Command Modes

  • /exec/configure/fex
1 threshold-percent {percent-threshold {percentup <up-percentage> [percentdown<down-percentage>] | percentdown<down-percentage> [percentup <up-percentage>] }} | no threshold-percent {percent-threshold} line 1, column 77: -, ., ::, :, /, [, whitespaces, | or ] expected, < encountered.