System Setup and Software Installation Guide for Cisco NCS 1014, IOS XR Releases 26.x.x

Preliminary checks for Cisco NCS 1014

Updated: October 7, 2026

Want to summarize with AI?

Describes the verification checks that you must perform after you log in to the Cisco NCS 1014 console so that you can confirm the default setup and correct any issue before further configuration.

A preliminary check for Cisco NCS 1014 is a post-login verification process that

involves running a set of commands to confirm the system has come up correctly,
checks the hardware inventory, the operational state of each card, and software image and firmware versions, and
verifies environmental parameters, management connectivity, active alarms, core dumps, and core files.

Sample output and references

Note

The sample output in these procedures is not from the latest software release. The output changes for any explicit reference to the current release.

Note

For details about proactive system monitoring that you can use to prevent potential issues, see System Health Check.

Inventory support in Cisco NCS 1014

The Cisco NCS 1014 inventory model is the set of hardware components that the system reports when you query its inventory. It consists of:

one Cisco NCS 1014 controller card,
one Cisco NCS 1014 chassis,
two AC or DC power supply units (PSU) of 2 KW and 2.5 KW,
three FAN trays, and
four line cards.

Table 1. Feature History
Feature Name	Release Information	Description
Inventory support	Cisco IOS XR Release 26.1.1	The NCS 1014 system enables inventory support for these new line cards. NCS1K14-2.4T-A-K9 NCS1K14-2.4TAL-K9
Inventory support	Cisco IOS XR Release 25.1.1	Inventory support and pluggable optics support are enabled in NCS 1014 system. NCS1K-MD-32O-CE and NCS1K-MD-32E-CE ONS-QSFP-OTDR DP01QSDD-ZT5-A1 ONS-SC-PTP-1510
Inventory support	Cisco IOS XR Release 7.11.1	Inventory support and pluggable optics support for QSFP28,QSFP-DD and Coherent Interface Module (CIM 8) are enabled in NCS 1014 system.

Card name mapping

The short names used in this guide map to the following Cisco line card product IDs (PIDs):

CCMD-16-C: refers to the NCS1K14-CCMD-16-C card.
CCMD-16-L: refers to the NCS1K14-CCMD-16-L card.
1.2T: refers to the NCS1K4-1.2T-K9 C-band card.
2.4T: refers to the NCS1K4-2.4T-K9 DWDM transponder and muxponder card.
2.4TA: refers to the NCS1K14-2.4T-A-K9 DWDM transponder and muxponder card.
EDFA2: refers to the NCS1K4-EDFA2 C-band card.
NCS1K-MD-32O-CE: refers to the NCS 1000 32-channel Odd Mux/Demux 150 GHz C-band Enhanced card.
NCS1K-MD-32E-CE: refers to the NCS 1000 32-channel Even Mux/Demux 150 GHz C-band Enhanced card.

Unique device identifier (UDI) reported by show inventory

The show inventory command retrieves and displays inventory information for each Cisco product in the form of a unique device identifier (UDI). The UDI is a combination of three data elements:

Product identifier (PID): The name by which the product is ordered. The PID is also known as the product name or part number.
Version identifier (VID): The version of the product. The VID is incremented whenever an upgrade changes the product.
Serial number (SN): The vendor-assigned unique serial number that identifies a specific product instance.

Verify the hardware inventory on Cisco NCS 1014 device

Use this task to confirm that the physical entities and modules installed in your Cisco NCS 1014 system are correctly identified, so that you can use the inventory data for operational and troubleshooting needs.

The show inventory command displays the inventory details of all the physical entities that are installed on Cisco NCS 1014. You can use specific keywords with the command to filter the inventory information you want to retrieve, such as all, details, fan, power, vendor-type, raw, chassis, and location.

Procedure

Run the show inventory command with the keyword that matches the inventory information that you want to retrieve.

For sample outputs of each keyword variant, see Sample outputs of the show inventory command.
(Optional) Restrict the output to a specific node by appending the location location keyword to the command.
Example:
```
RP/0/RP0/CPU0:ios#show inventory location 0/1/NXR0
```

Cisco NCS 1014 displays the inventory information that corresponds to the show inventory keyword that you ran.

Sample outputs of the show inventory command

The following sections show representative outputs for each keyword variant of the show inventory command. Use these samples together with the Verify the hardware inventory of Cisco NCS 1014 task.

show inventory

The following sample output shows the inventory summary of the chassis, controller, FAN modules, PSUs, and line cards.

RP/0/RP0/CPU0:ios#show inventory

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2652B1XA

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2717B1GB

NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2704B0P7

NAME: "0/FT1", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B18D

NAME: "0/FT2", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2704B0PA

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit 2.5KW"
PID: NCS1K4-AC-PSU-2   , VID: V00, SN: POG26300N0V

NAME: "0/PM1", DESCR: "Network Convergence System 1004 AC Power Supply Unit 2.5KW"
PID: NCS1K4-AC-PSU-2   , VID: V00, SN: POG26300N1H

NAME: "0/0/NXR0", DESCR: "NCS 1014 2.4T Line Card Ver 2"
PID: NCS1K14-2.4T-A-K9 , VID: V00, SN: FCB2921B2BM

NAME: "0/1/NXR0", DESCR: "NCS 1014 2.4T Licensed card-Ver2"
PID: NCS1K14-2.4TAL-K9 , VID: V00, SN: FCB2942B0JC

NAME: "0/2/NXR0", DESCR: "NCS 1014 2.4T licensed Card- crossconnect modes"
PID: NCS1K14-2.4TXL-K9 , VID: V01, SN: FCB2921B2WC

NAME: "0/3/NXR0", DESCR: "NCS 1014 2.4T Line Card Ver 2"
PID: NCS1K14-2.4T-A-K9 , VID: V00, SN: FCB2942B0J3
RP/0/RP0/CPU0:ios#

show inventory details

The following sample output shows the detailed inventory information, including the manufacturer name, SNMP index, hardware version, and part number for each physical entity.

RP/0/RP0/CPU0:ios#show inventory details

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2652B1XA
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 8384513   , Type: Rack
PN: 800-111211-01, HW Ver: 0.1

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2717B1GB
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 16385     , Type: Module
PN: 800-111209-01, HW Ver: 0.2

NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2704B0P7
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 28673     , Type: Fantray
PN: 800-111210-01, HW Ver: 0.1

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit 2.5KW"
PID: NCS1K4-AC-PSU-2   , VID: V00, SN: POG26300N0V
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 20481     , Type: Power Supply
PN: 341-101364-01, HW Ver: 0.1

NAME: "0/0/NXR0", DESCR: "NCS 1014 2.4T Licensed card-Ver2"
PID: NCS1K14-2.4T-A-K9 , VID: V00, SN: FCB2921B2BM
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 1         , Type: Module
PN: 800-52136-01, HW Ver: 0.1
RP/0/RP0/CPU0:ios#

show inventory all

The following sample output shows the inventory information for all the physical entities in the chassis, including line cards and pluggable optics modules.

RP/0/RP0/CPU0:ios#show inventory all
Mon Nov 27 11:01:53.452 UTC

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2717B13C

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2723B0CX

NAME: "0/0/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1014 2.4T Line Card"
PID: NCS1K14-2.4T-K9   , VID: V00, SN: FCB2710B0L5

NAME: "Optics0/1/0/0", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: SIM-AX12-SW

NAME: "Optics0/1/0/1", DESCR: "Cisco 100G QSFP28 SR4-S Pluggable Optics Module"
PID: QSFP-100G-SR4-S   , VID: ES1 , SN: AVF1933G18C
RP/0/RP0/CPU0:ios#

show inventory location

The following sample output shows the inventory information for a specific line card location, including all pluggable optics modules installed on that line card.

show inventory chassis

The following sample output shows the chassis-only inventory information.

RP/0/RP0/CPU0:ios#show inventory chassis
Mon Nov 27 11:02:05.083 UTC

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2717B13C
RP/0/RP0/CPU0:ios#

show inventory fan

The following sample output shows the inventory information for all the FAN modules installed on the chassis.

RP/0/RP0/CPU0:ios#show inventory fan
Mon Nov 27 11:02:39.811 UTC

NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B192

NAME: "0/FT1", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B197

NAME: "0/FT2", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B19U
RP/0/RP0/CPU0:ios#

show inventory power

The following sample output shows the inventory information for the power supply units (PSU) installed on the chassis.

RP/0/RP0/CPU0:ios#sh inventory power
Mon Nov 27 11:03:04.566 UTC

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2727CLP6

Need help?

Open a support case

(Requires a Cisco Service Contract)

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.