PDF(293.5 KB) View with Adobe Reader on a variety of devices
Updated:November 13, 2015
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Release Notes for Cisco Small Business SPA112/SPA122/SPA232D/SPA302D Analog Telephone Adapter Firmware Version 1.4.1
First Published: November 15, 2015
These Release Notes describe the updates and fixes in version 1.4.1 of the Cisco Small Business SPA112/SPA122/SPA232D/SPA302D ATA firmware.
As with any firmware release, read these release notes before you upgrade the firmware. Cisco also recommends that you back up the configuration before you perform any firmware upgrade.
For SPA112/SPA122/SPA232D/SPA302D ATA firmware, the openssl upgrades from 1.0.1h to 1.0.1p.
For SPA112/SPA122/SPA232D/SPA302D ATA firmware, the net-snmp upgrades from 5.7.2 to 5.7.3.
For SPA112/SPA122/SPA232D/SPA302D ATA firmware, the expat upgrades from 2.0.1 to 2.1.0.
Hardware and Firmware Compatibility
The following matrix describes the hardware and firmware compatibility.
(3 types of devices)
1.3.5p and 1.3.2p (SPA112/SPA122)
(128MB Flash + New SLIC)
CCQ18400001 to CCQ1841033K
CCQ1834031U to CCQ1834037D
CCQ1847066I to CCQ184707YA
CCQ184902ED to CCQ184904UL
CCQ184904UM to CCQ184904Y3
CCQ184904Y4 to CCQ184904Y5
(128MB Flash + Old SLIC)
CCQ175106J3 to CCQ175106OM
CCQ181607OO to CCQ181607U7
CCQ18240E34 to CCQ18400000
CCQ1841033L to CCQ18500D9K
CCQ174602V3 to CCQ1746030M
CCQ181502B7 to CCQ181502GQ
CCQ182002W3 to CCQ1834031T
CCQ1834037E to CCQ18470660
CCQ184707YB to CCQ184902EC
CCQ184904UM to CCQ184904UL
CCQ184904Y4 to CCQ184904Y3
CCQ184904Y6 to CCQ185001YH
CCQ17100G3L to CCQ1906001U
(32MB Flash + Old SLIC)
Note Do not upgrade any device to an unsupported firmware version as detailed in the Hardware and Firmware Compatibility Matrix table.
Note New SLIC devices have a label that reads S/W: Must use 1.3.5(004p) or later.
New and Changed Feature
Proxy Redundancy Mechanism
Cisco phone supports the use of backup SIP Proxy Servers to minimize or eliminate service disruption.
A new parameter Auto Register when Failover is added to control the phone adapter to autoregister on failover proxy (when failover action is executed). After reregistering successfully, the INVITE message is resent to new proxy.
Upgrade the Firmware
Follow these instructions to upgrade the phone adapter.
Step 1 Download the latest firmware by using the Firmware link on the following web page:
Step 2 Access the adapter Configuration Utility in one of the following two ways:
If the adapter is SPA112, connect one analog phone to its FXS port, press **** to access IVR, enter 110 to get SPA112 WAN IP address. Then, launch a web browser, and enter WAN IP address.
If the adapter is SPA122 or SPA232D, connect one PC to its LAN port. Then, launch a web browser, and enter the LAN IP address. The default value is 192.168.15.1.
Step 3 Log in to the Configuration Utility.
Step 4 Click Administration in the menu bar, and then click Firmware Upgrade in the navigation tree.
Step 5 Click Browse and select the location of the upgrade file that you downloaded.
Step 6 Click the Upgrade button to upgrade the firmware.
Note Upgrading the firmware may take several minutes. Until the process is complete, do not turn off the power, press the hardware reset button, or click the Back button in your current browser.
spa1x2: TCP, reg fallback on 1st&3rd then after 5s fallback on 2nd&3rd.
Broadsoft fax issue.
SPA122 audio issue-> clipped audio.
SPA112: LAN/WAN IP conflict detection enabled with only one port.
SPA122: Line fails to register when one SIP outbound proxy server failed.
SPA122: DTMF received incorrectly in FXS port.
SPA122/SPA232D- Proxy Redundancy mechanism.
Behavior During Times of Network Congestion
Anything that degrades network performance can affect voice and video quality, and in some cases, can cause a call to drop. Sources of network degradation can include, but are not limited to, the following activities:
Administrative tasks, such as an internal port scan or security scan
Attacks that occur on your network, such as a Denial of Service attack
To reduce or eliminate any adverse effects to the devices, schedule administrative network tasks during a time when the devices are not being used or exclude the devices from testing.
Documentation, Service Requests, and Additional Information
Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation as an RSS feed and delivers content directly to your desktop using a reader application. The RSS feeds are a free service.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.