Table Of Contents
show syslog heartbeat facility
show syslog heartbeat interval
show syslog heartbeat severity
Show Commands
Revised: July 22, 2009, OL-19335-01This chapter contains the following show commands:
•show syslog heartbeat facility
•show syslog heartbeat interval
•show syslog heartbeat severity
show call statistics addin
show call statistics addin [detail | page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Usage Guidelines
Use this command to retrieve the audio-addin statistics of the call.
Examples
admin:show call statistics addinCall StatisticsRegistered to Cisco Unified Call Manager : YesCall in Progress : YesCall Type : Audio/Video Call Call Start Time: Jul 12 11:40:35 2007Duration (sec) : 53 Direction : OutgoingLocal Number : 12345 Remote Number : 23456State : Answered Bit Rate : 4000000 bps,1080p-- Audio Add-in --IP Addr Src : 11.17.126.73:16386 Dst : 0.0.0.0:0Latency Avg : 1 Period : 0Statistics Left Center Right AuxTx Bytes 0Tx Packets 0Rx Bytes 0Rx Packets 0Rx Packets Lost 0Related Commands
Command DescriptionRetrieves all the statistics of the call.
Retrieves the audio statistics of the call.
Retrieves the video statistics of the call.
show call statistics all
show call statistics all [detail | page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve all the statistics of the call.
Examples
admin:show call statistics allCall StatisticsRegistered to Cisco Unified Call Manager : YesCall in Progress : YesCall Type : Audio/Video Call Call Start Time: Jul 12 11:40:35 2007Duration (sec) : 53 Direction : OutgoingLocal Number : 12345 Remote Number : 23456State : Answered Bit Rate : 4000000 bps,1080p-- Audio --IP Addr Src : 11.17.126.73:16386 Dst : 11.17.126.42:16384Latency Avg : 1 Period : 0Statistics Left Center Right AuxTx Bytes 7655120 7655283 7655114 0Tx Packets 45839 45840 45840 0Rx Bytes 7491593 7582158 7467858 0Rx Packets 45131 45678 44988 0Rx Packets Lost 45 65 13 0-- Video --IP Addr Src : 11.17.126.73:16386 Dst : 11.17.126.42:16384Latency Avg : 1 Period : 0Statistics Left Center Right AuxTx Bytes 216305260 196115964 288648018 0Tx Packets 221717 198464 290134 0Rx Bytes 219270020 223672084 152227219 0Rx Packets 205040 208662 158232 0Rx Packets Lost 5069 6798 914 0-- Audio Add-in --IP Addr Src : 11.17.126.73:16386 Dst : 0.0.0.0:0Latency Avg : 1 Period : 0Statistics Left Center Right AuxTx Bytes 0Tx Packets 0Rx Bytes 0Rx Packets 0Rx Packets Lost 0Related Commands
Command DescriptionRetrieves the audio-addin statistics of the call.
Retrieves the audio statistics of the call.
Retrieves the video statistics of the call.
show call statistics audio
show call statistics audio [detail | page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the audio statistics of the call.
Examples
admin:show call statistics audioCall StatisticsRegistered to Cisco Unified Call Manager : YesCall in Progress : YesCall Type : Audio/Video Call Call Start Time: Jul 12 11:40:35 2007Duration (sec) : 53 Direction : OutgoingLocal Number : 12345 Remote Number : 23456State : Answered Bit Rate : 4000000 bps,1080p-- Audio --IP Addr Src : 11.17.126.73:16386 Dst : 11.17.126.42:16384Latency Avg : 1 Period : 0Statistics Left Center Right AuxTx Bytes 7655120 7655283 7655114 0Tx Packets 45839 45840 45840 0Rx Bytes 7491593 7582158 7467858 0Rx Packets 45131 45678 44988 0Rx Packets Lost 2 3 1 0Related Commands
Command DescriptionRetrieves the audio-addin statistics of the call.
Retrieves all the statistics of the call.
Retrieves the video statistics of the call.
show call statistics video
show call statistics video [detail | page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the video statistics of the call.
Examples
admin:show call statistics videoCall StatisticsRegistered to Cisco Unified Call Manager : YesCall in Progress : YesCall Type : Audio/Video Call Call Start Time: Jul 12 11:40:35 2007Duration (sec) : 49 Direction : OutgoingLocal Number : 12345 Remote Number : 23456State : Answered Bit Rate : 4000000 bps,1080p-- Video --IP Addr Src : 11.17.126.73:16388 Dst : 11.17.126.42:16388Latency Avg : 0 Period : 0Statistics Left Center Right AuxTx Bytes 216305260 196115964 288648018 0Tx Packets 221717 198464 290134 0Rx Bytes 219270020 223672084 152227219 0Rx Packets 205040 208662 158232 0Rx Packets Lost 5 6 4 0Related Commands
Command DescriptionRetrieves the audio-addin statistics of the call.
Retrieves all the statistics of the call.
Retrieves the audio statistics of the call.
show call status
show call status
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the status of the call.
Examples
admin:show call statusCall StatusRegistered to Cisco Unified Call Manager : YesCall in Progress : YesCall Type : Audio/Video Call Call Start Time: Jul 12 11:40:35 2007Duration (sec) : 23 Direction : OutgoingLocal Number : 12345 Remote Number : 23456State : Answered Bit Rate : 4000000 bps,1080pshow cert lsc
show cert lsc
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the contents of the Locally Significant Certificate (LSC).
Examples
admin:show cert lscRelated Commands
Command DescriptionDisplays the contents of the Manufacturing Installed Certificate (MIC).
Displays the contents of the Web Interface Certificate.
show cert mic
show cert mic
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the contents of the Manufacturing Installed Certificate (MIC).
Examples
admin:show cert micCertificate:Data:Version: 3 (0x2)Serial Number:70:54:8f:23:00:00:00:12:4f:d9Signature Algorithm: sha1WithRSAEncryptionIssuer: O=Cisco Systems, CN=Cisco Manufacturing CAValidityNot Before: Mar 17 12:59:06 2007 GMTNot After : Mar 17 13:09:06 2017 GMTSubject: CN=CTS-CODEC-PRIM-SEP0019AA043ABFSubject Public Key Info:Public Key Algorithm: rsaEncryptionRSA Public Key: (1024 bit)Modulus (1024 bit):00:a3:b0:d8:a3:4b:0a:e1:85:13:a9:78:d4:3f:24:c8:52:0f:11:f9:f2:bf:19:2b:9b:84:85:5e:0c:fd:ee:86:43:06:7b:64:54:1d:05:5a:27:d3:95:1f:d5:bb:c4:01:e8:b0:24:2a:6a:86:53:cb:85:b7:d4:70:84:63:c1:92:1b:3e:cd:d9:21:29:1b:36:4c:2f:03:8f:ad:6f:a9:94:2f:88:0a:d3:19:6a:1d:75:e3:f2:9f:19:5e:dd:c8:fc:54:d6:01:2a:73:f6:3c:9d:3e:74:74:72:a1:cc:30:f2:7d:d9:38:f3:4a:6b:f6:52:f0:20:0a:6e:7e:1f:a5:a4:49Exponent: 65537 (0x10001)X509v3 extensions:X509v3 Key Usage: criticalDigital Signature, Key EnciphermentX509v3 Subject Alternative Name:email:test@cisco.comX509v3 Subject Key Identifier:2A:AA:EF:DC:4C:A9:47:44:F2:43:8F:AE:FF:7B:8C:B1:A5:C9:04:FFX509v3 Authority Key Identifier:keyid:D0:C5:22:36:AB:4F:46:60:EC:AE:05:91:C7:DC:5A:D1:B0:47:F7:6CX509v3 CRL Distribution Points:URI:http://www.cisco.com/security/crl/cmca.crlAuthority Information Access:CA Issuers - URI:http://www.cisco.com/security/certs/cmca.cer1.3.6.2.4.1.311.20.2:.0.I.P.S.E.C.I.n.t.e.r.m.e.d.i.a.t.e.O.f.f.l.i.n.eSignature Algorithm: sha1WithRSAEncryption83:26:d7:c5:0f:f9:04:40:d5:e5:42:fe:dc:86:95:3d:af:99:da:92:f1:c1:fc:8c:31:9f:8d:1e:8b:75:e2:f3:61:e9:9c:5f:0d:93:00:80:75:05:ff:5c:d5:ad:14:cc:bf:ea:1e:79:a0:b1:b9:43:32:7e:2a:bb:fa:7b:89:47:7a:46:2d:db:20:13:6f:dd:26:de:21:6f:6c:7c:a5:26:1f:fb:15:ef:df:48:ca:9f:e3:1c:25:b2:39:1a:f4:ba:a7:a5:a5:26:90:bb:28:d3:d6:7b:bd:e5:5f:49:e8:39:6a:39:8f:97:18:3b:fe:fd:71:50:72:8b:e5:c8:a5:98:a3:f3:df:4b:da:2e:46:d5:9d:62:41:19:9e:09:bd:8f:61:04:ed:1f:0d:0d:d5:e2:64:ae:c0:fe:ab:a8:f3:c4:1b:a9:d3:3f:7e:41:35:c6:e9:1b:ec:79:7b:42:e4:a5:49:2f:e9:f6:71:79:8c:e2:67:7c:df:67:60:eb:3b:12:2a:49:66:68:46:b8:b7:0b:c8:da:29:8d:31:2c:86:38:07:43:89:9a:bc:60:ab:46:cf:d0:5f:5f:25:4f:ca:60:de:0b:9e:42:b1:aa:7f:2c:1f:17:dd:0a:5f:ca:6c:eb:28:95:b1:26:07:81:5b:31:76:e9:8d:44:af:16:22:d1SHA1 Fingerprint=6D:B6:56:A9:EA:07:5C:A8:92:5D:59:D9:F0:BA:E2:CC:F7:60:45:4E-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----Related Commands
Command DescriptionDisplays the contents of the Locally Significant Certificate (LSC).
Displays the contents of the Web Interface Certificate.
show cert web
show cert web
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the contents of the Web Interface Certificate.
Examples
admin:show cert webCertificate:Data:Version: 3 (0x2)Serial Number: 1 (0x1)Signature Algorithm: md5WithRSAEncryptionIssuer: O=Cisco Systems Inc., OU=TSBU, CN=TelePresence-webadminValidityNot Before: Jan 1 00:00:13 2006 GMTNot After : Jan 1 00:00:13 2026 GMTSubject: O=Cisco Systems Inc., OU=TSBU, CN=TelePresence-webadminSubject Public Key Info:Public Key Algorithm: rsaEncryptionRSA Public Key: (1024 bit)Modulus (1024 bit):00:97:37:5f:7c:7b:8b:af:5f:a0:5d:b7:4e:0d:37:cc:f5:f4:c1:28:4a:5b:13:ba:99:d3:df:c7:53:5d:87:10:01:c1:bb:d7:e6:c7:88:bd:dd:d5:2f:b5:08:e8:a3:42:6e:1f:3e:50:be:f8:2e:18:8d:1f:c0:0d:31:f2:c0:d2:b0:cf:9b:f9:ae:a3:19:80:75:56:df:98:9d:c5:3a:b4:65:43:71:33:bc:d3:15:30:10:21:d2:f0:d7:5c:00:68:8d:87:f1:35:28:14:e6:13:ae:a3:d5:fb:9d:bf:34:7d:a9:c2:cd:94:10:5e:ce:ea:86:84:41:ff:e4:ce:d6:77:79Exponent: 65537 (0x10001)Signature Algorithm: md5WithRSAEncryption09:c7:0f:df:fd:df:d0:0b:30:da:60:42:50:cc:4a:4f:f6:a1:19:61:3b:a2:9a:b2:5c:1b:ca:f6:80:28:9b:95:f6:12:da:48:fa:5e:d9:7a:de:98:1a:7b:b7:79:f7:5b:30:77:ac:d2:65:f7:29:40:10:4b:4f:d6:97:04:33:42:ae:17:48:36:cb:4e:b6:5f:d7:6b:fc:67:a1:72:2d:a8:c3:cd:44:3a:c8:22:e3:ae:e0:f2:05:f4:c8:81:37:73:42:0d:47:0d:9d:43:a1:9f:0a:b3:bb:50:00:0a:35:b0:9d:2d:3d:c8:76:69:00:24:9a:42:72:5c:e7:47:da:d6MD5 Fingerprint=4A:60:E5:98:FC:FF:F7:1B:FA:87:21:53:37:65:A1:6F-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----Related Commands
Command DescriptionDisplays the contents of the Locally Significant Certificate (LSC).
Displays the contents of the Manufacturing Installed Certificate (MIC).
show config all
show config all [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the configuration information.
Examples
admin:show config allSystem ConfigCCM Mode : CCMModel : Cisco TelePresence 1000Displays : 1Load Image : SIPTS-1.0.0.1.sbnTime Zone : Pacific SA Daylight TimeConference Room : customer roomPhone ConfigPhone Number : 15019Phone IP : 10.16.120.217Related Commands
Command DescriptionRetrieves the phone configuration information.
Retrieves the system configuration information.
show config phone
show config phone [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the phone configuration information.
Examples
admin:show config phonePhone ConfigPhone Number : 12500Phone IP : 10.00.00.100Phone Connection : UplinkRelated Commands
Command DescriptionRetrieves all configuration information.
Retrieves system configuration information.
show config system
show config system [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the system configuration information.
Examples
admin:show config systemSystem ConfigCCM Mode : CCMModel : Cisco TelePresence 1000Displays : 1Load Image : SIPTS-1.0.0.1.sbnTime Zone : Pacific SA Daylight TimeConference Room : customer roomshow directory alternate
show directory alternate
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the configured alternate directory server. If none are defined, then the default Cisco Unified Communications Manager (Cisco Unified CM) directory server is used.
Examples
admin:show directory alternateshow downrev-cucm status
show downrev-cucm status
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the current Cisco Unified Communications Manager (Cisco Unified CM) Down Revision support state. The Cisco Unified CM Down Revision feature enables or disables the Cisco TelePresence System (CTS) 3200 from working with Cisco Unified CM Release 5.x and later releases.
Examples
admin:show downrev-cucm statusThe current state of the CUCM Down Revision support: enabledRelated Commands
Command DescriptionDisables the CTS 3200 from working with Cisco Unified CM.
Enables the CTS 3200 to work with Cisco Unified CM.
show firewall status
show downrev-cucm status [detail | page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display firewall entries. You can also enter help in the command string to display the current firewall settings:
show firewall status helpExamples
admin:show firewall statusChain INPUT (policy DROP)target prot opt source destinationACCEPT all -- anywhere anywhereACCEPT icmp -- anywhere anywhereACCEPT all -- anywhere anywhere state RELATED,ESTABLISHEDACCEPT tcp -- anywhere anywhere state NEW tcp dpt:sipACCEPT tcp -- anywhere anywhere state NEW tcp dpt:8081ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:8082....Chain ipsla_resp (1 references)target prot opt source destinationChain video_rtcp (1 references)target prot opt source destinationChain video_rtp (1 references)target prot opt source destinationshow hardware all
show hardware all
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display all hardware information.
Examples
admin:show hardware allDisplay Serial Number : 44048101420563Display Hardware Version : 0400Display Model : UnknownDisplay Boot Code Version : INFO:Display is unsupportedDisplay App Code Version : INFO:Display is unsupportedRelated Commands
Command DescriptionDisplays all audio-related hardware information.
Displays all system-related hardware information.
Displays all video hardware information.
show hardware audio
show hardware audio
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display all audio-related hardware information.
Examples
admin:show hardware audioAudio Hardware Version : 4Audio CPLD Version : 6Audio DSP Build ID : 00.09.000bRelated Commands
Command DescriptionDisplays all hardware information.
Displays all system-related hardware information.
Displays all video hardware information.
show hardware system
show hardware system
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display all system hardware information.
Examples
admin:show hardware systemDisplay Hardware Version : 0400DisplaySerial Number : FSJC0537527DisplayProduct ID : CTS-CODEC-PRIM...Related Commands
Command DescriptionDisplays all hardware information.
Displays all audio-related hardware information.
Displays all video hardware information.
show hardware video
show hardware video
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display all video hardware information.
Examples
admin:show hardware videoDisplay Camera Brand : Lumenera/pulsarDisplay Camera Model : 1.0DDisplay Camera Hardware Version : 2Display Camera Firmware Version : 306:521Display Camera Firmware Image Date : Wed Apr 13 16:21:16 EST 2009...Related Commands
Command DescriptionDisplays all hardware information.
Displays all audio-related hardware information.
Displays all system-related hardware information.
show inventory
show inventory
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the platform inventory information
Examples
admin:show inventoryNAME: "ciscoTSPri", DESCR: "Cisco TelePresence Primary Codec"PID: CTS-CODEC-PRIM=, VID: V01, SN:FHH1059M00Mshow license status
show license status
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show license status.
Note If the status shows that the feature is enabled but not currently running, you may need to restart the calling services.
Examples
admin:show license statusLicense feature statussatellite:Valid license foundLicense feature is enabledFeature is currently runningRelated Commands
show myself
show myself
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show information about the current account
Examples
admin:show myselfMachine Name : SEP0019AA043ABFAccount name : testPrivilege level : 1Output setting : disabledLogging setting : disabledshow network all
show network all [detail | page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve all basic platform network information. It will concatenate the show network eth0, show network route, and show network status commands.
Examples
admin:show network allEthernet 0 - PrimaryDHCP : enabled Link Status: upIP Address : 12.32.49.141 IP Mask : 255.255.255.0MAC Address : 00:19:AA:04:3A:BF VLAN : 300Mode : Auto enabled, full duplex, 1000MB/sEthernet eth0:1IP Address : 192.168.0.1 IP Mask : 255.255.255.0Ethernet eth0:2IP Address : 192.168.1.1 IP Mask : 255.255.255.0Ethernet eth2IP Address : 192.168.2.1 IP Mask : 255.255.255.0Ethernet eth3IP Address : 192.168.3.1 IP Mask : 255.255.255.0DNSPrimary : 171.58.226.120 Secondary : 171.70.168.183Domain : cisco.comGateway : 12.32.49.1 on Ethernet eth0.300192.168.3.0/24 dev eth3 proto kernel scope link src 192.168.3.1192.168.2.0/24 dev eth2 proto kernel scope link src 192.168.2.1192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.1192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.110.32.49.0/24 dev eth0.300 proto kernel scope link src 12.32.49.141default via 12.32.49.1 dev eth0.300Active Internet connections (w/o servers)Proto Recv-Q Send-Q Local Address Foreign Address Statetcp 0 0 SEP0019AA043:TSCMA_Ctrl SEP0019AA043ABF:58108 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:58108 SEP0019AA043:TSCMA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:59800 ESTABLISHEDtcp 0 0 localhost:59800 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:60457 ESTABLISHEDtcp 0 0 localhost:60457 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:60453 ESTABLISHEDtcp 0 0 localhost:60453 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:60455 ESTABLISHEDtcp 0 0 localhost:60455 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 SEP0019AA043:TSCCA_Ctrl SEP0019AA043ABF:57079 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:57079 SEP0019AA043:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCMA_Ctrl localhost:52003 ESTABLISHEDtcp 0 0 localhost:52003 localhost:TSCMA_Ctrl ESTABLISHEDtcp 0 0 localhost:61463 localhost:52896 ESTABLISHEDtcp 0 0 localhost:52896 localhost:61463 ESTABLISHEDtcp 0 0 localhost:61463 localhost:52900 ESTABLISHEDtcp 0 0 localhost:52900 localhost:61463 ESTABLISHEDtcp 0 0 localhost:61463 localhost:52891 ESTABLISHEDtcp 0 0 localhost:52891 localhost:61463 ESTABLISHEDtcp 1 0 localhost:53219 localhost:61449 CLOSE_WAITtcp 0 0 localhost:45221 localhost:61448 TIME_WAITtcp 0 0 SEP0019AA043:TSOSD_Ctrl SEP0019AA043ABF:45634 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:45634 SEP0019AA043:TSOSD_Ctrl ESTABLISHEDtcp 0 0 localhost:61448 localhost:49006 ESTABLISHEDtcp 0 0 localhost:49006 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61448 localhost:49037 ESTABLISHEDtcp 0 0 localhost:49037 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61448 localhost:49047 ESTABLISHEDtcp 0 0 localhost:49047 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61448 localhost:49048 ESTABLISHEDtcp 0 0 localhost:49048 localhost:61448 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:42734 tsbu-de-cm4p.cisco.:sip ESTABLISHEDtcp 342 0 localhost:43719 localhost:61460 CLOSE_WAITtcp 342 0 localhost:43715 localhost:61460 CLOSE_WAITtcp 342 0 localhost:43679 localhost:61460 CLOSE_WAITtcp 342 0 localhost:43702 localhost:61460 CLOSE_WAITtcp 0 0 localhost:TSCMR_Ctrl localhost:44730 ESTABLISHEDtcp 0 0 localhost:44730 localhost:TSCMR_Ctrl ESTABLISHEDtcp 0 0 SEP0019AA043ABF:61458 tbipp.local:38853 ESTABLISHEDtcp 0 0 localhost:33035 localhost:61464 TIME_WAITtcp 0 0 localhost:33034 localhost:61464 TIME_WAITtcp 0 0 localhost:33037 localhost:61464 TIME_WAITtcp 0 0 localhost:33036 localhost:61464 TIME_WAITtcp 0 0 localhost:33038 localhost:61464 TIME_WAITtcp 0 0 localhost:61448 localhost:33694 ESTABLISHEDtcp 0 0 localhost:33694 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61452 localhost:34870 ESTABLISHEDtcp 0 0 localhost:34870 localhost:61452 ESTABLISHEDtcp 0 0 localhost:61454 localhost:36427 ESTABLISHEDtcp 0 0 localhost:36427 localhost:61454 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:42313 tbipp.local:www TIME_WAITtcp 0 0 SEP0019AA043ABF:42304 tbipp.local:www TIME_WAITtcp 0 0 SEP0019AA043ABF:42306 tbipp.local:www TIME_WAITtcp 0 0 SEP0019AA043ABF:61457 tbipp.local:22562 ESTABLISHEDActive UNIX domain sockets (w/o servers)Proto RefCnt Flags Type State I-Node Pathunix 9 [ ] DGRAM 1324 /dev/logunix 2 [ ] DGRAM 3407 /tmp/secCmdSockunix 2 [ ] DGRAM 3409 /tmp/secSrvrSockunix 2 [ ] DGRAM 37105unix 2 [ ] DGRAM 9775unix 2 [ ] DGRAM 3366unix 2 [ ] DGRAM 3317unix 2 [ ] DGRAM 3280unix 2 [ ] DGRAM 2738unix 2 [ ] DGRAM 2373unix 2 [ ] DGRAM 1332Related Commands
show network eth0
show network eth0 [detail]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve basic platform network information about Ethernet port 0.
Examples
admin:show network eth0Ethernet 0DHCP : no Status : UPIP Address : 192.0.2.0 IP Mask : 255.255.255.000Link Detected: yes Mode : Auto off, Full, 100MB/sDNSPrimary : 000.70.100.000 Secondary :Domain : cisco.comGateway : 000.107.100.1 on Ethernet 0Related Commands
Command DescriptionRetrieves all basic platform network information.
Retrieves some basic platform network route information.
Retrieves some basic platform network status information.
show network route
show network route [detail]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve some basic platform network route information.
Examples
admin:show network route192.168.3.0/24 dev eth3 proto kernel scope link src 192.168.3.1192.168.2.0/24 dev eth2 proto kernel scope link src 192.168.2.1192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.1192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.112.32.49.0/24 dev eth0.300 proto kernel scope link src 12.32.49.141default via 12.32.49.1 dev eth0.300Related Commands
Command DescriptionRetrieves all basic platform network information.
Retrieves some basic platform network information about Ethernet 0.
Retrieves some basic platform network status information.
show network status
show network status [detail | listen | process | all | nodns | search text]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve basic platform network status information. The search option must be followed by a text string. This string cannot contain any spaces or tabs. It is case insensitive. Search for the "stext" in the output.
Examples
admin:show network statusActive Internet connections (w/o servers)Proto Recv-Q Send-Q Local Address Foreign Address Statetcp 0 0 localhost:57656 localhost:61448 TIME_WAITtcp 0 0 localhost:57655 localhost:61448 TIME_WAITtcp 0 0 SEP0019AA043:TSCMA_Ctrl SEP0019AA043ABF:58108 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:58108 SEP0019AA043:TSCMA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:59800 ESTABLISHEDtcp 0 0 localhost:59800 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:60457 ESTABLISHEDtcp 0 0 localhost:60457 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:60453 ESTABLISHEDtcp 0 0 localhost:60453 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCCA_Ctrl localhost:60455 ESTABLISHEDtcp 0 0 localhost:60455 localhost:TSCCA_Ctrl ESTABLISHEDtcp 0 0 SEP0019AA043:TSCCA_Ctrl SEP0019AA043ABF:57079 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:57079 SEP0019AA043:TSCCA_Ctrl ESTABLISHEDtcp 0 0 localhost:TSCMA_Ctrl localhost:52003 ESTABLISHEDtcp 0 0 localhost:52003 localhost:TSCMA_Ctrl ESTABLISHEDtcp 0 0 localhost:61463 localhost:52896 ESTABLISHEDtcp 0 0 localhost:52896 localhost:61463 ESTABLISHEDtcp 0 0 localhost:61463 localhost:52900 ESTABLISHEDtcp 0 0 localhost:52900 localhost:61463 ESTABLISHEDtcp 0 0 localhost:61463 localhost:52891 ESTABLISHEDtcp 0 0 localhost:52891 localhost:61463 ESTABLISHEDtcp 1 0 localhost:53219 localhost:61449 CLOSE_WAITtcp 0 0 SEP0019AA043:TSOSD_Ctrl SEP0019AA043ABF:45634 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:45634 SEP0019AA043:TSOSD_Ctrl ESTABLISHEDtcp 0 0 localhost:61448 localhost:49006 ESTABLISHEDtcp 0 0 localhost:49006 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61448 localhost:49037 ESTABLISHEDtcp 0 0 localhost:49037 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61448 localhost:49047 ESTABLISHEDtcp 0 0 localhost:49047 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61448 localhost:49048 ESTABLISHEDtcp 0 0 localhost:49048 localhost:61448 ESTABLISHEDtcp 0 0 localhost:41042 localhost:61464 TIME_WAITtcp 0 0 localhost:41043 localhost:61464 TIME_WAITtcp 0 0 localhost:41044 localhost:61464 TIME_WAITtcp 0 0 localhost:41045 localhost:61464 TIME_WAITtcp 0 0 localhost:41046 localhost:61464 TIME_WAITtcp 0 0 SEP0019AA043ABF:42734 tsbu-de-cm4p.cisco.:sip ESTABLISHEDtcp 342 0 localhost:43719 localhost:61460 CLOSE_WAITtcp 342 0 localhost:43715 localhost:61460 CLOSE_WAITtcp 342 0 localhost:43679 localhost:61460 CLOSE_WAITtcp 342 0 localhost:43702 localhost:61460 CLOSE_WAITtcp 0 0 localhost:TSCMR_Ctrl localhost:44730 ESTABLISHEDtcp 0 0 localhost:44730 localhost:TSCMR_Ctrl ESTABLISHEDtcp 0 0 SEP0019AA043ABF:61458 tbipp.local:38853 ESTABLISHEDtcp 0 0 localhost:61448 localhost:33694 ESTABLISHEDtcp 0 0 localhost:33694 localhost:61448 ESTABLISHEDtcp 0 0 localhost:61452 localhost:34870 ESTABLISHEDtcp 0 0 localhost:34870 localhost:61452 ESTABLISHEDtcp 0 0 localhost:61454 localhost:36427 ESTABLISHEDtcp 0 0 localhost:36427 localhost:61454 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:61457 tbipp.local:22562 ESTABLISHEDtcp 0 0 SEP0019AA043ABF:45152 tbipp.local:www TIME_WAITtcp 0 0 SEP0019AA043ABF:45154 tbipp.local:www TIME_WAITtcp 0 0 SEP0019AA043ABF:45143 tbipp.local:www TIME_WAITActive UNIX domain sockets (w/o servers)Proto RefCnt Flags Type State I-Node Pathunix 9 [ ] DGRAM 1324 /dev/logunix 2 [ ] DGRAM 3407 /tmp/secCmdSockunix 2 [ ] DGRAM 3409 /tmp/secSrvrSockunix 2 [ ] DGRAM 37105unix 2 [ ] DGRAM 9775unix 2 [ ] DGRAM 3366unix 2 [ ] DGRAM 3317unix 2 [ ] DGRAM 3280unix 2 [ ] DGRAM 2738unix 2 [ ] DGRAM 2373unix 2 [ ] DGRAM 1332Related Commands
Command DescriptionRetrieves all basic platform network information.
Retrieves some basic platform network information about Ethernet 0.
Retrieves some basic platform network route information.
show ringtone status
show ringtone status
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the ringtone state.
Examples
admin:show ringtone statusThe current state of ringtone: disabledshow secondary status
show secondary status
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the status of the secondary codecs.
Examples
admin:show secondary statustesting left...secondary is still bootingtesting right...secondary is upRelated Commands
show security authstring
show security authstring
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the CAPF authentication string.
Examples
admin:show security authstring123456Related Commands
show security info
show security info [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show security information.
Examples
admin:show security infosecurity information====================version : 1.0 [Apr 30 2007, 14:05:07]MIC : yesLSC : NOdevice sec mode : 1 (auth)num CTL entries : 4timers in use : 0 timerssockets in use : 3 socketsclnt SSL in use : 0 clnt SSLactive reqs. : 0 reqs.info o/p on : nonedebug o/p on : noneverbose o/p on : noneRelated Commands
show security trustlist
show security trustlist [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the security trustlist.
Examples
admin:show security trustlistctl info=========ctl file (if any) : /nv/security/ctl/CTLFile.tlvhash of CTL (16 bytes):max allowed entries : 32max allowed entries : 32num current entries : 4CTS has CTLCTL table entries:CTL-tbl [0]role: 0 (SAST)ip : n/adns :sub : cn="SAST-ADN418e4e14 ";ou=IPCBU;o="Cisco Systemsiss : cn=CAP-RTP-001;o=Cisco Systemsser : available, 10 bytespkey: available, 140 bytessig : n/ahash: n/acert: available, 933 bytesCTL-tbl [1]role: 0 (SAST)ip : n/adns :sub : cn="SAST-ADN47ece814 ";ou=IPCBU;o="Cisco Systemsiss : cn=CAP-RTP-002;o=Cisco Systemsser : available, 10 bytespkey: available, 140 bytessig : n/ahash: n/acert: available, 907 bytesCTL-tbl [2]role: 2 (CCM_TFTP)ip : 171.28.176.239dns : test-cm5-10sub : cn=test-cm5-10.cisco.comiss : cn=test-cm5-10.cisco.comser : available, 8 bytespkey: available, 140 bytessig : n/ahash: n/acert: available, 578 bytesCTL-tbl [3]role: 4 (CAPF)ip : 100.00.100.239dns : test-cm5-10sub : cn=CAPF-45131e4a;o=ciscoiss : cn=CAPF-45131e4a;o=ciscoser : available, 8 bytespkey: available, 140 bytessig : n/ahash: n/acert: available, 626 bytesRelated Commands
show status
show status
Syntax Description
There are no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve basic platform status information.
Examples
admin:show statusHost Name : SEP0019AA043ABFDate : Mon Apr 27, 2009 22:55:02Time Zone : GMTLocale : en_USProduct Ver : CTS 2009-04-24System State : Run NormalBoot Slot : 2Uptime:10:55pm up 2 days, 23:17, load average: 0.01, 0.06, 0.07Memory Total: 516180KFree: 115360KUsed: 400820KShared: 0KBuffers: 262268KTotal Free UsedDisk/ram 253871K 115417K 138454K (55%)Disk/logging 103847K 56844K 41641K (42%)Disk/factory 47104K 6148K 40956K (86%)Disk/slot 1 47088K 5325K 41763K (88%)Disk/slot 2 47088K 4932K 42156K (89%)Related Commands
show syslog facility
show syslog facility
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the syslog default facility used for logging messages.
Examples
admin:show syslog facilityFacility not set, using default of local0Related Commands
Command DescriptionShows the syslog time zone setting as either local time or GMT/UTC.
Shows the syslog output version.
show syslog heartbeat facility
show syslog heartbeat facility
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the syslog heartbeat facility used for heartbeat messages.
Examples
admin:show syslog heartbeat facilityFacility not set, using default of local0Related Commands
Command DescriptionShows the currently configured heartbeat interval in minutes.
Shows the configured heartbeat message test string.
Shows the configured severity of the heartbeat messages.
show syslog heartbeat interval
show syslog heartbeat interval
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the syslog heartbeat interval in minutes; 0 minutes is disabled.
Examples
admin:show syslog heartbeat intervalInterval not set, using default of 0(disabled)Related Commands
Command DescriptionShows the configured facility configured for heartbeat messages.
Shows the configured heartbeat message test string.
Shows the configured severity of the heartbeat messages.
show syslog heartbeat msg
show syslog heartbeat msg
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the configured heartbeat message test string.
Examples
admin:show syslog heartbeat msgMessage not set, using default of "Syslog heartbeat message"Related Commands
show syslog heartbeat severity
show syslog heartbeat severity
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the configured severity of the heartbeat messages.
Examples
admin:show syslog heartbeat severitySeverity not set, using default of 6(info)Related Commands
Command DescriptionShows the configured facility configured for heartbeat messages.
Shows the currently configured heartbeat interval in minutes.
Shows the configured heartbeat message test string.
show syslog timezone
show syslog timezone
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the syslog time zone setting as either local time or GMT/UTC.
Examples
admin:show syslog timezoneTimezone not set, using default of GMT/UTCRelated Commands
Command DescriptionDisplays the current timezone setting in long format.
Lists all the available timezones in long format.
show syslog version
show syslog version
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the syslog output version, either CiscoLog v1.1 or IETF/RFC Syslog Protocol Version 1.
Examples
admin:show syslog versionVersion is not set, using default of IETF/RFC Syslog Protocol v1 formatRelated Commands
Command DescriptionShows the syslog default facility used for logging messages
Shows the syslog time zone setting as either local time or GMT/UTC
show tech network
show tech network [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show network aspects of the machine. This command also shows detailed information about the following:
•Ethernet interfaces
•Routes
•Host file
•Resolver file
•Network connections
Examples
admin:show tech networkRelated Commands
show tech runtime
show tech runtime [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show runtime aspects of the machine. This command also shows detailed information about the following:
•Environment variables
•System resources
•Processor usage
•NV registry
•FW registry
Examples
admin:show tech runtime page 1-------------------- show platform runtime --------------------environment variablesConsoleRows=23SHELL=/usr/local/bin/startcliTERM=vt100SSH_CLIENT=111.70.11.114 2446 22SSH_TTY=/dev/ttyp1ConsoleColumns=62USER=adminPATH=/bin:/usr/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/local/sbin:.MAIL=/var/mail/adminPWD=/nv/home/adminLANG=en_USparamLine=name=admin priv=4 role=masterHOME=/nv/home/adminSHLVL=2LOGNAME=adminSSH_CONNECTION=111.70.11.114 2446 10.32.49.141 22UPG_RUNNING=0:enter for 1 line, space for one page, q to quitRelated Commands
show tech system
show tech system [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show system aspects of the machine. This command also shows the following:
•Machine name
•Software modules
•Hardware pci bus
•Security information
Examples
admin:show tech systemRelated Commands
show timezone config
show timezone config
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to display the current timezone setting in long format.
Examples
admin:show timezone configCurrent timezone: (GMT+10:00) Canberra, Melbourne, SydneyRelated Commands
show timezone list
show timezone list [page]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to list all the available timezones in long format.
Examples
admin:show timezone list(GMT-12:00) Eniwetok, Kwajalein(GMT-11:00) Midway Island, Samoa(GMT-10:00) Hawaii::(GMT+12:00) Auckland, Wellington(GMT+13:00) Nuku\x27alofaCurrent timezone: (GMT+10:00) Canberra, Melbourne, SydneyRelated Commands
show upgrade
show upgrade [detail]
Syntax Description
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to show the status of the upgrade. The detail keyword will show the current versions of the peripherals as well as the peripheral firmware versions in the image. If a peripheral has been marked for forced upgrade with the set upgrade commands, the entry will be followed by an "F" in the output. See Set Commands and Unset Commands.
Examples
admin:show upgradeThere are no peripherals being upgrade at this timeleft sub system...There are no peripherals being upgrade at this timeright sub system...There are no peripherals being upgrade at this timeshow version
show version
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
Admin
Command privilege level: 0
Command History
Usage Guidelines
Use this command to retrieve the version number of the software on the system. There will be an asterisk next to the currently booted version.
Examples
admin:show versionSlot0 = SIPTS 1.0.0.201*Slot1 = SIPTS 1.0.2.101Slot2 = SIPTS 1.0.1.045