Agent Capabilities Supported

Available Languages

Download Options

  • PDF     (576.4 KB)
    View with Adobe Reader on a variety of devices
Updated:November 2, 2007

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Agent Capabilities Supported

Table Of Contents

Agent Capabilities Supported

Overview

Agent Capabilities MIBs

Cisco MGX 8800 Traps Capabilities

Cisco ATM Capabilities

Cisco ATM Connections Capabilities

Cisco AXSM-E ATM Connections Capabilities

Cisco WAN RPM ATM Connection Capabilities

Cisco ATM Virtual IF Capabilities

Cisco ATM Virtual IF Capabilities for AXSM-E

Basis Shelf Capabilities

Cisco Bulk File Capabilities

Cisco DS3 Capabilities

DS3 Capabilities

Cisco DS3 Capabilities for AXSM-E

Entity Capabilities

Cisco Entity FRU Control Capabilities

IF Capabilities

Cisco WAN PXM IF Capabilities

Cisco WAN IF Capabilities Used for AXSM

Cisco IF Capabilities Used for AXSM-E

SNMPv2 Capabilities

PNNI Capabilities

RS-232 Capabilities

Cisco WAN Resource Partition Capabilities

Cisco WAN Resource Partition Capabilities for RPM

SONET Capabilities

Cisco WAN SVC Capabilities

Cisco System Capabilities

Cisco AXSM Cisco SONET Capabilities

Cisco AXSM-E Cisco SONET Capabilities

Cisco AXSM WAN Module Capabilities

Cisco AXSM-E WAN Module Capabilities

Cisco AXSM-E ATM Cell Layer Capabilities

Cisco AXSM-E ATM Connection Statistics Capabilities

Cisco WAN RPM Subinterface Capabilities


Agent Capabilities Supported

This chapter describes the agent capabilities used for AXSM, AXSM-E, PXM45, and RPM service modules.

Contents of this chapter include:

•Overview

•Agent Capabilities MIBs

Overview

According to RFC 2580, the agent capabilities macro is a set of capabilities for a SNMP agent. Agent capabilities allow the SNMP agent to define the level of support needed for the applicable Management Information Base (MIB) group. The description is bound to the value of the sysORID object, which is the object identifier for the entry. For example, several MIB objects can have either restricted or augmented syntax or access levels. For more detailed information, refer to RFC 2580.

Agent Capabilities MIBs

The MIBs used for the agent capabilities contain information on the limitations to support the MIB objects. The agent capabilities used for the applicable service module are listed in Table 8-1.

Note The agent capabilities used for Release 2 are compatible for Release 2.1.

Table 8-1 MIBs Used for Agent Capabilities 

MIB Name
Agent Capability MIB Name
Service Module

CISCO-MGX8800-TRAPS-MIB

CISCO-MGX8800-TRAPS-CAPABILITY.my

AXSM PXM45
RPM

ATM-MIB

CISCO-WAN-ATM-CAPABILITY.my

PXM45

CISCO-ATM-CONN-MIB

CISCO-WAN-AXSM-ATM-CONN-CAPABILITY.my

AXSM

CISCO-WAN-ATM-CONN-MIB

CISCO-AXSME-ATM-CONN-CAPABILITY.my

AXSM-E

CISCO-ATM-VIRTUAL-IF-MIB

CISCO-WAN-AXSM-ATM-VIRTUAL-IF-CAPABILITY.my

AXSM

CISCO-AXSME-ATM-VIRTUAL-IF-CAPABILITY.my

AXSM-E

BASIS-SHELF-MIB

CISCO-WAN-BASIS-SHELF-CAPABILITY.my

PXM45

CISCO-BULK-FILE-MIB

CISCO-WAN-BULK-FILE-CAPABILITY.my

AXSM PXM45 RPM

CISCO-DS3-MIB

CISCO-WAN-CISCO-DS3-CAPABILITY.my

AXSM

CISCO-AXSME-CISCO-DS3-CAPABILITY.my

AXSM-E

DS3-MIB

CISCO-WAN-DS3-CAPABILITY.my

AXSM

ENTITY-MIB

CISCO-WAN-ENTITY-CAPABILITY.my

PXM45

CISCO-ENTITY-FRU-CONTROL-MIB

CISCO-WAN-ENTITY-FRU-CAPABILITY.my

PXM45

IF-MIB

CISCO-WAN-IF-CAPABILITY.my1

AXSM

CISCO-WAN-PXM-IF-CAPABILITY.my2

PXM45

CISCO-AXSME-IF-CAPABILITY.my

AXSM-E

SNMPv2-MIB

CISCO-WAN-MGX8800-SNMPV2-CAPABILITY.my

PXM45

PNNI-MIB

CISCO-WAN-PNNI-CAPABILITY.my

PXM45

RS-232-MIB

CISCO-WAN-RS-232-CAPABILITY.my

PXM45
PXM1

CISCO-WAN-RSRC-PART-MIB

CISCO-WAN-RSRC-PART-CAPABILITY.my

AXSM

CISCO-WAN-RPM-RSRC-PART-MIB

CISCO-WAN-RPM-RSRC-PART-CAPABILITY.my

RPM

SONET-MIB

CISCO-WAN-SONET-CAPABILITY.my

AXSM

CISCO-WAN-SVC-MIB

CISCO-WAN-SVC-CAPABILITY.my

PXM45

CISCO-SYSTEM-MIB

CISCO-WAN-SYSTEM-CAPABILITY.my

PXM45

CISCO-WAN-RPM-ATM-CONN-MIB

CISCO-WAN-RPM-ATM-CONN-CAPABILITY.my

RPM

CISCO-SONET-MIB

CISCO-AXSM-CISCO-SONET-CAPABILITY.my

AXSM

CISCO-AXSME-CISCO-SONET-CAPABILITY.my

AXSM-E

CISCO-WAN-MODULE-MIB

CISCO-AXSM-WAN-MODULE-CAPABILITY.my

AXSM

CISCO-AXSME-WAN-MODULE-CAPABILITY.my

AXSM-E

CISCO-ATM-CELL-LAYER-MIB

CISCO-AXSME-ATM-CELL-LAYER-CAPABILITY.my

AXSM-E

CISCO-WAN-ATM-CONN-STAT-MIB

CISCO-AXSME-ATM-CONN-STAT-CAPABILITY.my

AXSM-E

CISCO-WAN-RPM-SUBIF-MIB

CISCO-WAN-RPM-SUBIF-CAPABILITY.my

RPM

1 The CISCO-WAN-IF-CAPABILITY.my file is used for AXSM.

2 The CISCO-WAN-PXM-IF-CAPABILiTY.my file is used for PXM45.


Cisco MGX 8800 Traps Capabilities

The following are the object groups applicable to the Cisco MGX8800 traps capabilities:

•cwSonetNotificationsGroup

•cwSonetStatsNotificationsGroup

•cwDs3NotificationsGroup

•cwDs3LoopbackNotificationsGroup

•cwDs3StatsNotificationsGroup

•cwDs3PlcpNotificationsGroup

•cwAtmIfNotificationsGroup

•cwCardIngNotificationsGroup

•cwRsrcPartNotificationsGroup

•cwVsiControllerNotificationsGroup

•cwFeederNotificationsGroup

The Cisco MGX 8800 Traps capabilities reside in the CISCO-MGX8800-TRAPS-CAPABILITY.my file. For more detailed description about each trap, see "Traps and Alarms Supported."

The variation type of MIB objects are listed in Table 8-2.

Table 8-2 Cisco MGX8800 Traps Capabilities 

Variation Name
Capability Specific Varbinds
MIB Specific Varbinds
MIB Access
Capability Access

cwAtmPhyInAlarm

none

ifIndex, ifName

none

not implemented

cwAtmPhyNoAlarm

none

ifIndex, ifName

none

not implemented


Cisco ATM Capabilities

The atmInterfaceConfGroup2 object group is applicable to Cisco WAN ATM Capabilities. The Cisco ATM capabilities reside in the CISCO-WAN-ATM-CAPABILITY.my file. For a more detailed description about each variation object, see "PNNI MIB Objects".

The variation type of MIB objects are listed in Table 8-3.

Table 8-3 Cisco WAN ATM Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

atmInterfaceMaxVpcs

none

INTEGER (0..4096)

Specifies that the atmInterfaceMaxVpcs variation object is not supported.

Max-Access: read-write

Access: not implemented

atmInterfaceMaxVccs

none

INTEGER (0..65536)

Specifies that the atmInterfaceMaxVccs variation object is not supported.

Max-Access: read-write

Access: not implemented

atmInterfaceConfVpcs

none

INTEGER (0..4096)

Specifies that the atmInterfaceConfVpcs variation object is not supported.

Max-Access: read-only

Access: not implemented

atmInterfaceConfVccs

none

INTEGER (0..65536)

Specifies that the atmInterfaceConfVccs variation object is not supported.

Max-Access: read-only

Access: not implemented

atmInterfaceMaxActiveVpiBits

none

INTEGER (0..12)

Specifies that the atmInterfaceMaxActiveVpiBits variation object is not supported.

Max-Access: read-write

Access: not implemented

atmInterfaceMaxActiveVciBits

none

INTEGER (0..16)

Specifies that the atmInterfaceMaxActiveVciBits variation object is not supported.

Max-Access: read-write

Access: not implemented

atmInterfaceIlmiVpi

none

AtmVpIdentifier

Specifies that the atmInterfaceIlmiVpi variation object is not supported.

Max-Access: read-write

Access: not implemented

atmInterfaceIlmiVci

none

AtmVcIdentifier

Specifies that the atmInterfaceIlmiVci variation object is not supported.

Max-Access: read-write

Access: not implemented

atmInterfaceMyNeighborIpAddress

none

IpAddress

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

atmInterfaceMyNeighborIfName

none

DisplayString

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

atmInterfaceCurrentMaxVpiBits

none

INTEGER (0..12)

Specifies that the atmInterfaceCurrentMaxVpiBits variation object is not supported.

Max-Access: read-only

Access: not implemented

atmInterfaceCurrentMaxVciBits

none

INTEGER (0..16)

Specifies that the atmInterfaceCurrentMaxVciBits variation object is not supported.

Max-Access: read-only

Access: not implemented

atmInterfaceSubscrAddress

none

AtmAddr

Specifies that the atmInterfaceSubscrAddress variation object is not supported.

Max-Access: read-write

Access: not implemented


Cisco ATM Connections Capabilities

The following are the object groups applicable to Cisco WAN AXSM ATM CONN capabilities:

•ciscoWanAtmConnChanMIBGroup

•ciscoWanAtmConnStateGroup

The Cisco ATM Connections capabilities reside in the CISCO-WAN-AXSM-ATM-CONN-CAPABILITY.my file.

For a more detailed description about each variation object, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-4.

Table 8-4 Cisco WAN AXSM ATM Connections Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwaChanControllerId

none

Unsigned32 (1..255)

Specifies that the value used for a write operation is ignored. The read operation returns the controller ID configured in the shelf.

Max-Access: read-create

Access: read-create

cwaChanPCR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanMCR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanSCR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanRemotePCR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanRemoteMCR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanRemoteSCR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanAbrICR

Unsigned32 (7..5651328)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

Access: read-create

cwaChanCDV

Unsigned32(0..16777215)

Unsigned32 (0..16777215)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanCTD

Unsigned32(0..65535)

Unsigned32 (0..65535)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanMBS

Unsigned32(0..5000000)

Unsigned32 (0..5000000)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanCDVT

Unsigned32(0..5360000)

Unsigned32 (0..4294967295)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanRemoteCDV

Unsigned32(0..16777215)

Unsigned32 (0..16777215)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanRemoteCTD

Unsigned32(0..65535)

Unsigned32 (0..65535)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanRemoteMBS

Unsigned32(0..5000000)

Unsigned32 (0..5000000)

Specifies write support for a restricted range.

Max-Access: read-create

cwaChanRemoteCDVT

Unsigned32(0..5360000)

Unsigned32 (0..4294967295)

Returns the value 0xFFFFFFFF on a read operation.

Max-Access: read-create

cwaChanPercentUtil

none

Unsigned32 (0..100)

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanRemotePercent
Util

none

Unsigned32 (0..100)

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanRowStatus

INTEGER
{active(1), notInService(2),
createAndGo(4),
destroy(6)}

RowStatus

Specifies the value createAndWait(5) is not supported.

Max-Access: read-create

cwaChanIntAbrVSVD

none

CiscoWanVSVDConfg

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanExtAbrVSVD

none

CiscoWanVSVDConfg

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanAisIWCapability

none

CiscoWanAisIW

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanCLR

none

Unsigned32 (1..15)

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanRemoteCLR

none

Unsigned32 (1..15)

Specifies the value in a write operation is ignored. The read operation returns the default value.

Max-Access: read-create

Access: read-create

cwaChanTestType

INTEGER { noLpbk(1), nonDestructive(3) }

CiscoWanLpbkTypes

Specifies the value destructive(2) is not supported.

Max-Access: read-create

cwaChanTestIterations

Unsigned32 (1..1)

Unsigned32 (1..255)

Supports the value 1.

Max-Access: read-create


Cisco AXSM-E ATM Connections Capabilities

This section describes the agent capabilities that support the Cisco WAN ATM Connections MIB for AXSM-E.

The following are the object groups applicable to the CISCO-AXSME-ATM-CONN-CAPABILITY.my file:

•ciscoWanAtmConnChanMIBGroup

•ciscoWanAtmConnStateGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of objects are listed in Table 8-5.

Table 8-5 Cisco AXSM-E ATM Connections Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwaChanControllerId

none

Unsigned32 (1..255)

Specifies that the value in the write operation is ignored. The read operation returns the controller ID configured in the shelf.

cwaChanPCR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanMCR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanSCR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanRemotePCR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanRemoteMCR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanRemoteSCR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanAbrICR

Unsigned32 (7..1412830)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanCDVT

Unsigned32
(0..5360000)

Unsigned32 (0..4294967295)

Specifies that the write operation is supported with the restricted range.

cwaChanRemote
CDVT

Unsigned32
(0..5360000)

Unsigned32 (0..4294967295)

Specifies that the value 0xFFFFFFFF is always returned for the read operation.

cwaChanPercentUtil

none

Unsigned32 (0..100)

Specifies that the value in the write operation is ignored. The read operation returns the default value.

cwaChanRemote
PercentUtil

none

Unsigned32 (0..100)

Specifies that the value in the write operation is ignored. The read operation returns the default value.

cwaChanRowStatus

INTEGER {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}

RowStatus

Specifies that the createAndWait(5) value is not supported.

cwaChanAbrVSVD
Enable

none

TruthValue

Specifies that the cwaChanAbrVSVDEnable variation object is not supported.

Access: not-implemented

cwaChanAbrERS

none

CiscoWanERSConfg

Specifies that the value in the write operation is ignored. The read operation returns the default value.

cwaChanAisIW
Capability

none

CiscoWanAisIW

Specifies that the value in the write operation is ignored. The read operation returns the default value.

cwaChanCLR

none

Unsigned32 (1..15)

Specifies that the value in the write operation is ignored. The read operation returns the default value.

cwaChanRemoteCLR

none

Unsigned32 (1..15)

Specifies that the value in the write operation is ignored. The read operation returns the default value.

cwaChanTestType

INTEGER { noLpbk(1), nonDestructive(3) }

CiscoWanLpbkTypes

Specifies that the value destructive(2) is not supported.

cwaChanTestIterations

Unsigned32 (1..1)

Unsigned32 (1..255)

Supports only value 1.


Cisco WAN RPM ATM Connection Capabilities

This section describes the agent capabilities that support the Cisco WAN ATM CONN MIB for Router Processor Module (RPM).

The following are the object groups applicable to the CISCO-WAN-RPM-ATM-CONN-CAPABILITY.my file:

•ciscoWanAtmConnChanMIBGroup

•ciscoWanAtmConnStateGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-6.

Table 8-6 Cisco WAN RPM ATM Connection Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwaChanVpi

Unsigned32(0..255)

Unsigned32 (0..4095)

Supports the value 0 for the VCC.

Max-Access: not-accessible

cwaChanVci

Unsigned32(1..3808)

Unsigned32 (0..65535)

Specifies that the cwaChanVci variation object is used for the VCC.

Max-Access: not-accessible

cwaChanService
Category

INTEGER
{ vbr3nRt(7),
ubr1(8),
abr(10) }

CiscoAtmServiceCategory

Specifies that the values cbr1(1), vbr1RT(2), vbr2RT(3), vbr3RT(4), vbr1nRT(5), vbr2nRT(6), ubr2(9), cbr2(11), and cbr3(12) are not supported.

Max-Access: read-create

cwaChanIdentifier

Unsigned32(17..4095)

Unsigned32 (0..4294967295)

Specifies that the supported range is 17 to 3824 for VCC, and the supported range is 3841 to 4095 for VPC.

Max-Access: read-only

cwaChanStats
Enable

none

TruthValue

Specifies that the read operation returns a value false(2). Write operation is not supported.

Max-Access: read-create

cwaChanLocalVpi

Unsigned32(0..255)

Unsigned32 (0..4095)

Specifies that the VPI value is set to zero for VCC.

Max-Access: read-only

cwaChanLocalVci

Unsigned32(1..3808)

Unsigned32 (0..65535)

Determines the valid range for VCC.

Max-Access: read-only

cwaChanRemote
Vpi

Unsigned32(0..255)

Unsigned32 (0..4095)

Specifies that the VPI value is set to 0 for VCC.

Max-Access: read-create

cwaChanRemote
Vci

Unsigned32(1..3808)

Unsigned32 (0..65535)

Determines the valid range for VCC.

Max-Access: read-create

cwaChanCCEnable

none

TruthValue

Specifies that the read operation returns a value false(2). Write operation is not supported.

Max-Access: read-create

Access: read-only

cwaChanFrame
Discard

none

TruthValue

Specifies that the read operation returns a value false(2). This value is ignored for the write operation.

Max-Access: read-create

cwaChanPCR

Unsigned32(7..353208)

Unsigned32 (0..4294967295)

Specifies that the cwaChanPCR variation object is not supported.

Max-Access: read-create

cwaChanMCR

Unsigned32(7..353208)

Unsigned32 (0..4294967295)

Supports the limited range only.

Max-Access: read-create

cwaChanSCR

Unsigned32(7..353208)

Unsigned32 (0..4294967295)

Supports the limited range only.

Max-Access: read-create

cwaChanCDV

none

Unsigned32 (0..16777215)

Specifies that the cwaChanCDV variation object cannot be created or modified.

Max-Access: read-create

Access: read-only

cwaChanCTD

none

Unsigned32 (0..65535)

Specifies that the cwaChanCTD variation object cannot be created or modified.

Max-Access: read-create

Access: read-only

cwaChanMBS

Unsigned32(1..65535)

Unsigned32 (0..5000000)

Supports only the limited range.

Max-Access: read-create

cwaChanCDVT

none

Unsigned32 (0..4294967295)

Specifies that the cwaChanCDVT variation object cannot be created or modified.

Access: read-only

cwaChanRemote
PCR

Unsigned32(7..353208)

Unsigned32 (0..4294967295)

Supports only the limited range.

Max-Access: read-create

cwaChanRemote
MCR

Unsigned32(7..353208)

Unsigned32 (0..4294967295)

Supports only the limited range.

Max-Access: read-create

cwaChanRemote
SCR

Unsigned32(7..353208)

Unsigned32 (0..4294967295)

Supports only the limited range.

Max-Access: read-create

cwaChanRemote
CDV

none

Unsigned32 (0..16777215)

Specifies that the cwaChanRemoteCDV variation object cannot be created or modified.

Access: read-only

cwaChanRemote
CTD

none

Unsigned32 (0..65535)

Specifies that the cwaChanRemoteCTD variation object cannot be created or modified.

Access: read-only

cwaChanRemote
CDVT

none

Unsigned32 (0..4294967295)

Specifies that the cwaChanRemoteCDVT variation object cannot be created or modified.

Access: read-only

cwaChanAbrICR

none

Unsigned32 (0..4294967295)

Specifies that the cwaChanAbrICR variation object cannot be created or modified.

Access: read-only

cwaChanAbrADTF

none

Unsigned32 (1..1023)

Specifies that the cwaChanAbrADTF variation object cannot be created or modified.

Access: read-only

cwaChanAbrRIF

none

AbrRateFactors

Specifies that the cwaChanAbrRIF variation object cannot be created or modified.

Access: read-only

cwaChanAbrNRM

none

INTEGER {nrm2(1), nrm4(2), nrm8(3), nrm16(4), nrm32(5), nrm64(6), nrm128(7), nrm256(8)}

Specifies that the cwaChanAbrNRM variation object cannot be created or modified.

Access: read-only

cwaChanAbrTRM

none

INTEGER {trm0point78125(1), trm1point5625(2), trm3point125(3), trm6point25(4), trm12point5(5), trm25(6), trm50(7), trm100(8)}

Specifies that the cwaChanAbrTRM variation object cannot be created or modified.

Access: read-only

cwaChanAbrCDF

none

INTEGER {cdf0(1), cdfOneOver64(2), cdfOneOver32(3), cdfOneOver16(4), cdfOneOver8(5), cdfOneOver4(6), cdfOneOver2(7), cdfOne(8)}

Specifies that the cwaChanAbrCDF variation object cannot be created or modified.

Access: read-only

cwaChanAbrFRTT

none

Unsigned32 (0..16700000)

Specifies that the cwaChanAbrFRTT variation object cannot be created or modified.

Access: read-only

cwaChanAbrTBE

none

Unsigned32 (0..16777215)

Specifies that the cwaChanAbrTBE variation object cannot be created or modified.

Access: read-only

cwaChanAbrERS

none

CiscoWanERSConfg

Specifies that the write operation is ignored.

cwaChanAbrVSVDEnable

none

TruthValue

Specifies that the write operation is ignored.

cwaChanIntAbr
VSVD

none

CiscoWanVSVDConfg

Specifies that the write operation is ignored.

cwaChanExtAbr
VSVD

none

CiscoWanVSVDConfg

Specifies that the write operation is ignored.

cwaChanAisIW
Capability

none

CiscoWanAisIW

Specifies that the cwaChanAisIWCapability variation object cannot be created or modified.

Access: read-only

cwaChanCLR

none

Unsigned32 (1..15)

Specifies that the cwaChanCLR variation object cannot be created or modified.

Access: read-only

cwaChanRemote
CLR

none

Unsigned32 (1..15)

Specifies that the cwaChanRemoteCLR variation object cannot be created or modified.

Access: read-only

cwaChanEgress
XmtState

none

CiscoWanXmtState

Specifies that the cwaChanEgressXmtState variation object always returns a value zero.

cwaChanEgressRcvState

none

CiscoWanRcvState

Specifies that the cwaChanEgressRcvState variation object always returns a value zero.

cwaChanIngress
XmtState

none

CiscoWanXmtState

Specifies that the cwaChanIngressXmtState variation object always returns a value zero.

cwaChanIngress
RcvState

none

CiscoWanRcvState

Specifies that the cwaChanIngressRcvState variation object always returns a value zero.


Cisco ATM Virtual IF Capabilities

The following are the object groups applicable to the Cisco WAN AXSM ATM Virtual IF Capabilities for AXSM:

•caviMIBGroup

•caviEgressStatMIBGroup

•caviIngressStatMIBGroup

The Cisco ATM Virtual IF capabilities reside in the CISCO-WAN-AXSM-ATM-VIRTUAL-IF-CAPABILITY.my file.

For a more detailed description about each variation object, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-7.

Table 8-7 Cisco WAN AXSM ATM Virtual IF Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

caviIfType

INTEGER
{ uni(1),
nni(2)
vnni(3)}

INTEGER {uni(1),
nni(2),
vnni(3),
vuni(4)}

Specifies that value vuni(4) is not supported.

caviMinRate

Unsigned32 (50..5651320)

Unsigned32

Determines that the upper limit is the maximum rate for OC48 and equals to 5651320 cells per second.

caviMaxRate

Unsigned32 (50..5651320)

Unsigned32

Determines that the upper limit is the maximum rate for OC48 and equals to 5651320 cells per second.

caviEgrRMCells

none

Counter32

Specifies that the caviEgrRMCells variation object is not supported.

Access: not implemented

caviEgrXmtEFCICells

none

Counter32

Specifies that the caviEgrXmtEFCICells variation object is not supported.

Access: not implemented

caviEgrRcvEFCICells

none

Counter32

Specifies that the caviEgrRcvEFCICells variation object is not supported.

Access: not implemented

caviEgrXmtOAMCells

none

Counter32

Specifies that the caviEgrXmtOAMCells variation object is not supported.

Access: not implemented

caviHEgrXmtClp0Cells

none

Counter32

Specifies that the caviHEgrXmtClp0Cells variation object is not supported.

Access: not implemented

caviHEgrXmtClp1Cells

none

Counter32

Specifies that the caviHEgrXmtClp1Cells variation object is not supported.

Access: not implemented

caviIngRMCells

none

Counter32

Specifies that the caviIngRMCells variation object is not supported.

Access: not implemented

caviIngXmtEFCICells

none

Counter32

Specifies that the caviIngXmtEFCICells variation object is not supported.

Access: not implemented

caviIngRcvEFCICells

none

Counter32

Specifies that the caviIngRcvEFCICells variation object is not supported.

Access: not implemented

caviIngRcvOAMCells

none

Counter32

Specifies that the caviIngRcvOAMCells variation object is not supported.

Access: not implemented

caviHIngRcvClp0Cells

none

Counter64

Specifies that the caviHIngRcvClp0Cells variation object is not supported.

Access: not implemented

caviHIngRcvClp1Cells

none

Counter64

Specifies that the caviHIngRcvClp1Cells variation object is not supported.

Access: not implemented


Cisco ATM Virtual IF Capabilities for AXSM-E

The following are the object groups applicable to the Cisco ATM Virtual IF MIB capabilities for AXSM-E:

•caviMIBGroup

•caviEgressStatMIBGroup

•caviIngressStatMIBGroup

•caviEgressIntervalMIBGroup

The Cisco ATM Virtual IF capabilities reside in the CISCO-AXSME-ATM-VIRTUAL-IF-CAPABILITY.my file.

For a more detailed description about each variation object, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-8.

Table 8-8 Cisco AXSM-E ATM Virtual IF Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

caviIfType

INTEGER
{ uni(1),
nni(2)
vnni(3)}

INTEGER {uni(1),
nni(2),
vnni(3),
vuni(4)}

Specifies that value vuni(4) is not supported.

caviMinRate

Unsigned32 (50..1412830)

Unsigned32

Determines that the upper limit is the maximum rate for OC12 and equals to 1412830 cells per second.

caviMaxRate

Unsigned32 (50..1412830)

Unsigned32

Determines that the upper limit is the maximum rate for OC12 and equals to 1412830 cells per second.

caviEgrRMCells

none

Counter32

Specifies that the caviEgrRMCells variation object is not supported.

Access: not implemented

caviEgrXmtEFCICells

none

Counter32

Specifies that the caviEgrXmtEFCICells variation object is not supported.

Access: not implemented

caviEgrRcvEFCICells

none

Counter32

Specifies that the caviEgrRcvEFCICells variation object is not supported.

Access: not implemented

caviEgrXmtOAMCells

none

Counter32

Specifies that the caviEgrXmtOAMCells variation object is not supported.

Access: not implemented

caviHEgrXmtClp0Cells

none

Counter32

Specifies that the caviHEgrXmtClp0Cells variation object is not supported.

Access: not implemented

caviHEgrXmtClp1Cells

none

Counter32

Specifies that the caviHEgrXmtClp1Cells variation object is not supported.

Access: not implemented

caviIngRMCells

none

Counter32

Specifies that the caviIngRMCells variation object is not supported.

Access: not implemented

caviIngXmtEFCICells

none

Counter32

Specifies that the caviIngXmtEFCICells variation object is not supported.

Access: not implemented

caviIngRcvEFCICells

none

Counter32

Specifies that the caviIngRcvEFCICells variation object is not supported.

Access: not implemented

caviIngRcvOAMCells

none

Counter32

Specifies that the caviIngRcvOAMCells variation object is not supported.

Access: not implemented

caviHIngRcvClp0Cells

none

Counter64

Specifies that the caviHIngRcvClp0Cells variation object is not supported.

Access: not implemented

caviHIngRcvClp1Cells

none

Counter64

Specifies that the caviHIngRcvClp1Cells variation object is not supported.

Access: not implemented


Basis Shelf Capabilities

The following are the object groups applicable to Cisco WAN Basis Shelf Capabilities:

•shelfInfoGroup

•shelfNodeGroup

•shelfStatsGroup

•shelfApsInfoGroup

•shelfAxisInfoGroup

•shelfClkRateGroup

•shelfRedundancyGroup

For a more detailed description about each variation object, refer to the CISCO-WAN-BASIS-SHELF-CAPABILITY.my file.

The variation type of MIB objects are listed in Table 8-9.

Table 8-9 Cisco WAN Basis Shelf Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

shelfNumOfValidEntries

none

INTEGER (0..64)

Specifies the shelfNumOfValidEntres variation object is not supported.

Access: not implemented

shelfDate

none

DisplayString (SIZE (10))

Specifies the shelfDate variation object is not supported.

Access: not implemented

shelfTime

none

DisplayString (SIZE (8))

Specifies the shelfTime variation object is not supported.

Access: not implemented

shelfTmZn

none

INTEGER{
gmt (1),
est (2),
cst (3),
mst (4),
pst (5),
edt (6),
cdt (7),
mdt (8),
pdt (9)}

Specifies that the shelfTmZn variation object is not supported.

Access: not implemented

shelfTmZnGMTOff

none

INTEGER (-12..12)

Specifies that the shelfTmZnGMTOff variation object is not supported.

Access: not implemented

shelfBkPlnType

none

INTEGER (1..10)

Specifies that the shelfBkPlnType variation object is not supported.

Access: not implemented

shelfBkplnSerialNum

none

DisplayString (SIZE (0..11))

Specifies that the shelfBkplnSerialNum variation object is not supported.

MIB Access: read-only

Access: not implemented

shelfAlarmCardBitMap

none

INTEGER

Specifies that the shelfAlarmCardBitMap variation object is not supported.

Access: not implemented

shelfSlotNum

none

INTEGER (1..33)

Specifies that the shelfSlotNum variation object is not supported.

MIB Access: read-only

Access: not implemented

shelfBkplnSerialNumDeprecated

none

INTEGER (1..4)

Specifies that the shelfBkplnSerialNumDeprecated variation object is not supported.

MIB Access: read-only

Access: not implemented

shelfFunctionModuleState

none

INTEGER{
nocard (1),
standby (2),
active (3),
failed (4),
selfTest (5),
heldInReset (6),
boot (7),
mismatch (8),
unknown (9),
coreCardMismatch (10),
blocked (11),
reserved (12),
-- hold state applies to PXM during Graceful Upgrade.
hold (13)}

Specifies that the shelfFunctionModuleState variation object is not supported.

Access: not implemented

shelfFunctionModuleType

none

INTEGER
{other (1), asc (2),
pxm1 (1000),
pxm1-2t3e3 (1001),
pxm1-4oc3 (1002),
pxm1-oc12 (1003),
rpm (2000)}
rpm-pr (2001)}

Specifies that the shelfFunctionModuleType variation object is not supported.

MIB Access: read-only

Access: not implemented

shelfFunctionModuleHoldReset

none

INTEGER {
doNotHold (1),
holdInReset(2) }

Specifies that the shelfFunctionModuleHoldReset variation object is not supported.

MIB Access: read-write

Access: not implemented

redPrimaryType

none

INTEGER
{other (1),
bsc (2),
-- reserved for MGX8850 after 1000
pxm1 (1000),
pxm1-2t3e3 (1001),
pxm1-4oc3 (1002),
pxm1-oc12 (1003),
rpm (2000)}
rpm-pr (2001)}

Specifies that the redPrimaryType variation object is not supported.

Note The redPrimaryType object is not supported by PXM45 for
Release 2.1.

MIB Access: read-only

Access: not implemented

redSecondaryType

none

INTEGER
{other (1),
bsc (2),
-- reserved for MGX8850 after 1000
pxm1 (1000),
pxm1-2t3e3 (1001),
pxm1-4oc3 (1002),
pxm1-oc12 (1003),
rpm (2000)}
rpm-pr (2001)}

Specifies that the redSecondaryType variation object is not supported.

Note The redSecondaryType object is not supported by PXM45 for
Release 2.1.

MIB Access: read-only

Access: not implemented

redFeature

none

INTEGER

Specifies that the redFeature variation object is not supported.

MIB Access: read-only

Access: not implemented

redLineModuleType

none

INTEGER {
lm-DB15-4T1 (16),
lm-DB15-4E1 (17),
lm-BNC-4E1 (18),
lm-DB15-4T1-R(19),
lm-DB15-4E1-R(20),
lm-BNC-4E1-R (21),
lm-RJ48-8T1 (22),
lm-RJ48-8E1 (23),
lm-SMB-8E1 (24),
lm-RJ48-T3T1 (25),
lm-RJ48-E3E1 (26),
lm-RJ48-T3E1 (27),
lm-SMB-E3E1 (28),
lm-RJ48-E3T1 (29),
lm-SMB-T3E1 (30),
lm-T3E3-D (32),
lm-T3E3-B (33),
lm-RJ48-8T1-R(48),
lm-RJ48-8E1-R(49),
lm-SMB-8E1-R (50),
-- HSSI/X.21 Added by Suheel
lm-HS1-4X21 (60),
lm-HS1-3HSSI (61),
-- HSSI/X.21
lm-HS1-4V35 (62)}

Specifies that the redLineModuleType variation object is not supported.

Note The redLineModuleType object is not supported by PXM45 for Release 2.1.

MIB Access: read-only

Access: not implemented


Cisco Bulk File Capabilities

The following are the object groups applicable to Cisco WAN Bulk File capabilities:

•ciscoBulkFileDefineGroup

•ciscoBulkFileStatusGroup

The Cisco Bulk File capabilities reside in the CISCO-WAN-BULK-FILE-CAPABILITY.my file.

For a more detailed description, refer to the CISCO-BULK-FILE-MIB.my file.

The variation type of MIB objects are listed in Table 8-10.

Table 8-10 Cisco WAN Bulk File Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cbfDefineMaxFiles

none

Unsigned32 (0..4294967295)

Specifies that the cbfDefineMaxFiles variation object is not supported.

Max-Access: read-write

Access: not implemented

cbfDefineFiles

none

Gauge32

Specifies that the cbfDefineFiles variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfDefineHighFiles

none

Gauge32

Specifies that the cbfDefineHighFiles variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfDefineFilesRefused

none

Counter32

Specifies that the cbfDefineFilesRefused variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfDefineMaxObjects

none

Unsigned32 (0..4294967295)

Specifies that the cbfDefineMaxObjects variation object is not supported.

Max-Access: read-write

Access: not implemented

cbfDefineObjects

none

Gauge32

Specifies that the cbfDefineObjects variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfDefineHighObjects

none

Gauge32

Specifies that the cbfDefineHighObjects variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfDefineObjectsRefused

none

Counter32

Specifies that the cbfDefineObjectsRefused variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfDefineObjectClass

none

INTEGER
{object(1),
lexicalTable(2),
leastCpuTable(3)}

Specifies that the cbfDefineObjectClass variation object is not supported.

Max-Access: read-create

Access: not implemented

cbfDefineObjectID

none

OBJECT IDENTIFIER

Specifies that the cbfDefineObjectID variation object is not supported.

Max-Access: read-create

Access: not implemented

cbfDefineObjectEntryStatus

none

RowStatus

Specifies that the cbfDefineObjectEntryStatus variation object is not supported.

Max-Access: read-create

Access: not implemented

cbfStatusMaxFiles

none

Unsigned32 (0..4294967295)

Specifies that the cbfStatusMaxFiles variation object is not supported.

Max-Access: read-write

Access: not implemented

cbfStatusFiles

none

Gauge32

Specifies that the cbfStatusFiles variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfStatusHighFiles

none

Gauge32

Specifies that the cbfStatusHighFiles variation object is not supported.

Max-Access: read-only

Access: not implemented

cbfStatusFilesBumped

none

Counter32

Specifies that the cbfStatusFilesBumped variation object is not supported.

Max-Access: read-only

Access: not implemented


Cisco DS3 Capabilities

The following are the object groups applicable to Cisco WAN Cisco DS3 Capabilities:

•ciscoDs3ConfMIBGroup

•cds3StatsMIBGroup

•ciscoDs3AlarmMIBGroup

•ciscoPlcpAlarmMIBGroup

The Cisco DS2 capabilities reside in the CISCO-WAN-CISCO-DS3-CAPABILITY.my file.

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-11.

Table 8-11 Cisco WAN Cisco DS3 Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cds3LineType

INTEGER
{ds3cbitadm(1),
ds3cbitplcp(2),
e3g832adm(3) }

INTEGER
{ds3cbitadm(1), ds3cbitplcp(2), e3g832adm(3)}

Specifies that the values e3g751adm(4), e3751plcp(5), ds3m23adm(6), ds3m23plcp(7), and other(8) are not supported.

Max-Access: not-accessible

cds3InternalEqualizer

none

INTEGER
{use(1),
byPass(2)}

Specifies that the cds3InternalEqualizer variation object is not supported.

Max-Access: read-write

Access: not implemented

cds3NearEndLineLoopbackStatus

none

none

Specifies that the cds3NearEndLineLoopbackStatus variation object is not supported.

Access: not implemented

cds3FarEndLineLoopbackStatus

none

none

Specifies that the cds3FarEndLineLoopbackStatus variation object is not supported.

Access: not implemented


DS3 Capabilities

The following are the object groups applicable to Cisco WAN DS3 capabilities:

•ds3NearEndConfigGroup

•ds3NearEndStatisticsGroup

The DS3 capabilities reside in the CISCO-WAN-DS3-CAPABILITY.my file.

For a more detailed description about the variation objects, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-12.

Table 8-12 Cisco WAN DS3 Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

dsx3LineType

none

INTEGER {dsx3other(1), dsx3M23(2), dsx3SYNTRAN(3), dsx3CbitParity(4), dsx3ClearChannel(5), e3other(6), e3Framed(7), e3Plcp(8)}

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

dsx3Channelization

none

INTEGER {disabled(1), enabledDs1(2), enabledDs2(3)}

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

dsx3LoopbackConfig

INTEGER
{ dsx3NoLoop(1), dsx3LineLoop(3),
dsx3InwardLoop(5)}

INTEGER {dsx3NoLoop(1), dsx3PayloadLoop(2), dsx3LineLoop(3), dsx3OtherLoop(4), dsx3InwardLoop(5), dsx3DualLoop(6)}

Specifies that the values dsx3PayloadLoop(2), dsx3OtherLoop(4), and dsx3DualLoop(6) are not supported.

Max-Access: read-write

dsx3Ds1ForRemoteLoop

none

INTEGER (0..29)

Specifies that the dsx3Ds1ForRemoteLoop variation object is not supported.

Max-Access: read-write

Access: not implemented

dsx3TransmitClockSource

INTEGER
{ loopTiming(1), localTiming(2) }

INTEGER
{loopTiming(1), localTiming(2), throughTiming(3)}

Specifies that the value throughTiming(3) is not supported.

Max-Access: read-write


Cisco DS3 Capabilities for AXSM-E

The following are the object groups applicable to Cisco AXSM-E Cisco DS3 capabilities:

•ciscoDs3ConfMIBGroup

•cds3StatsMIBGroup

•ciscoDs3AlarmMIBGroup

•ciscoPlcpAlarmMIBGroup

•ciscoPlcpCounterMIBGroup

•ciscoDs3Previous24HrGroup

The DS3 capabilities for AXSM-E reside in the CISCO-AXSME-CISCO-DS3-CAPABILITY.my file.

For a more detailed description about the variation objects, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-13.

Table 8-13 Cisco AXSM-E DS3 Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cds3LineType

INTEGER {
ds3cbitadm(1),
ds3cbitplcp(2),
e3g832adm(3)
}

INTEGER
{ds3cbitadm(1), ds3cbitplcp(2), e3g832adm(3)}

Specifies that the values e3g751adm(4),e3751plcp(5), ds3m23adm(6),ds3m23plcp(7), and
other(8) are not supported.

cds3InternalEqualizer

none

INTEGER {
use(1),
byPass(2)
}

Specifies that the cds3InternalEqualizer variation object is not supported.

Access: not-implemented

cds3NearEndLineLoop
backStatus

none

Unsigned32
(0..2147483647)

Specifies that the cds3NearEndLineLoopbackStatus variation object is not supported.

Access: not-implemented

cds3NEAlarmUpCount

none

Unsigned32 (0..2147483647)

Specifies that the cds3NEAlarmUpCount variation object is not supported.

Access: not-implemented

cds3NEAlarmDown
Count

none

Unsigned32 (0..2147483647)

Specifies that the cds3NEAlarmDownCount variation object is not supported.

Access: not-implemented

cds3NEAlarmThreshold

none

Unsigned32 (0..2147483647)

Specifies that the cds3NEAlarmThreshold variation object is not supported.

Access: not-implemented

cds3FEAlarmUpCount

none

Unsigned32 (0..2147483647)

Specifies that the cds3FEAlarmUpCount variation object is not supported.

Access: not-implemented

cds3FEAlarmDown
Count

none

Unsigned32 (0..2147483647)

Specifies that the cds3FEAlarmDownCount variation object is not supported.

Access: not-implemented

cds3FEAlarmThreshold

none

Unsigned32 (0..2147483647)

Specifies that the cds3FEAlarmThreshold variation object is not supported.

Access: not-implemented

cds3FECount

none

Counter32

Specifies that the cds3FECount variation object is not supported.

Access: not-implemented

cds3EXZSCount

none

Counter32

Specifies that the cds3EXZSCount variation object is not supported.

Access: not-implemented

cds3LCVCount

none

Counter32

Specifies that the cds3LCVCount variation object is not supported.

Access: not-implemented

cds3PCVCount

none

Counter32

Specifies that the cds3PCVCount variation object is not supported.

Access: not-implemented

cds3CPECount

none

Counter32

Specifies that the cds3CPECount variation object is not supported.

Access: not-implemented

cds3FEBECount

none

Counter32

Specifies that the cds3FEBECount variation object is not supported.

Access: not-implemented

cds3RcvAISCount

none

Counter32

Specifies that the cds3RcvAISCount variation object is not supported.

Access: not-implemented


Entity Capabilities

The following object groups are applicable to Cisco WAN Entity capability:

•entityPhysicalGroup

•entityPhysical2Group

The entity capabilities reside in the CISCO-WAN-ENTITY-CAPABILITY.my file.

For a more detailed description, see "PXM MIB Objects."

The variation type of MIB objects are listed in Table 8-14.

Table 8-14 Cisco WAN Entity Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

entPhysicalName

none

SnmpAdminString

Specifies that the entPhysicalName object is set to one of the following:

•entPhysicalClass—Equal to module(9).

–Determines the slot number for the front module.

–Determines the slot number as seen in rear view of the chassis for the line module, for example, back cards.

•entPhysicalClass—Equal to chassis(1).

–Determines the chassis number, for example, shelf number.

Max-Access: read-only

entPhysicalMfgName

none

SnmpAdminString

Sets the PCB part number at the 800 level if applicable.

Max-Access: read-only

entPhysicalModelName

none

SnmpAdminString

Contains the zero-length string.

Max-Access: read-only

entPhysicalAssetID

none

SnmpAdminString (SIZE (0..32))

Specifies that the entPhysicalAssetID variation object is not supported.

Max-Access: read-write

Access: not implemented


Cisco Entity FRU Control Capabilities

The cefcMIBModuleGroup object group is applicable to Cisco WAN Entity FRU capabilities, which reside in the CISCO-WAN-ENTITY-FRU-CAPABILITY.my file.

For a more detailed description, see "PXM MIB Objects."

One variation type of the object is listed in Table 8-15.

Table 8-15 Cisco WAN Entity FRU Control Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cefcModuleAdminStatus

none

ModuleAdminType

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only


IF Capabilities

The agent capabilities for the IF-MIB contain three different files. They include:

•Cisco WAN PXM IF Capabilities used for PXM45

•Cisco WAN IF Capabilities used for AXSM

•Cisco AXSM-E IF Capabilities used for AXSM-E

Cisco WAN PXM IF Capabilities

The following are the object groups applicable to Cisco WAN PXM IF capabilities:

•ifGeneralInformationGroup

•ifPacketGroup

The Cisco WAN PXM IF capabilities reside in the CISCO-WAN-PXM-IF-CAPABILITY.my file.

For a more detailed description, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-16.

Table 8-16 Cisco WAN PXM IF Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

ifTableLastChange

none

TimeTicks

Specifies that the ifTableLastChange variation object is not supported.

Max-Access: read-only

Access: not implemented

ifAdminStatus

none

Integer {up (1),
ready to pass packets down; (2),
testing; (3) in some test mode}

Specifies that the ifAdminStatus variation object cannot be written for the RS-232 interface, which is identified by the ifType value rs232(33).

Max-Access: read-write

Access: read-write

ifOperStatus

INTEGER { up(1), down(2), testing(3) }

Integer {up (1), ready to pass packets;
down(2);
testing (3), in some test mode;
unknown (4), status can not be determined; dormant (5);
notPresent (6), some component is missing; lowerLayerDown (7), down due to state of lower-layer interface(s)}

Specifies that the ifOperStatus variation object is unable to detect all the states.

Max-Access: read-only

ifLastChange

none

TimeTicks

Specifies that the value cannot reflect the change in the operational status of the interface.

Max-Access: read-only

Access: read-only

ifLinkUpDownTrap
Enable

none

Integer {enabled (1), disabled (2)}

Specifies that the write operation is not supported.

The default value is disabled.

Max-Access: read-write

Access: read-only

ifAlias

none

DisplayString (SIZE(0..64))

Specifies that the ifAlias variation object is not supported.

Max-Access: read-write

Access: not implemented

ifInOctets

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifOutOctets

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifInUnknownProtos

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifInErrors

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifOutErrors

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifInUcastPkts

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifInMulticastPkts

none

Counter32

Specifies that the ifInMulticastPkts variation object is not supported.

Max-Access: read-only

Access: not implemented

ifInBroadcastPkts

none

Counter32

Specifies that the ifInBroadcastPkts variation object is not supported.

Max-Access: read-only

Access: not implemented

ifInDiscards

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifOutUcastPkts

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifOutMulticastPkts

none

Counter32

Specifies that the ifOutMulticastPkts variation object is not supported.

Max-Access: read-only

Access: not implemented

ifOutBroadcastPkts

none

Counter32

Specifies that the ifOutBroadcastPkts variation object is not supported.

Max-Access: read-only

Access: not implemented

ifOutDiscards

none

Counter32

Supports the following ifType interfaces:

•Ethernet interface—Determines the value ethernetCsmacd(6).

•Loopback interface—Determines the value softwareLoopback(24).

•SLIP Interface—Determines the value slip(28).

Max-Access: read-only

Access: read-only

ifPromiscuousMode

none

TruthValue

Specifies that the write operation is not supported.

Max-Access: read-write

Access: read-only

linkUp

none

{ifIndex, ifAdminStatus, ifOperStatus}

Specifies that the linkUp trap is not supported.

Status: current

Access: not implemented

linkDown

none

{ifIndex, ifAdminStatus, ifOperStatus}

Specifies that the linkDown trap is not supported.

Status: current

Access: not implemented


Cisco WAN IF Capabilities Used for AXSM

The ifGeneralInformationGroup is the object group applicable to Cisco WAN IF capabilities used for AXSM. These capabilities reside in the CISCO-WAN-IF-CAPABILITY.my file.

For a more detailed description, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-17.

Table 8-17 Cisco WAN IF Capabilities Used for AXSM 

Variation Name
Capability Syntax
MIB Syntax
Description

ifTableLastChange

none

TimeTicks

Specifies that the ifTableLastChange variation object is not supported.

Max-Access: read-only

Access: not implemented

ifPhysAddress

none

PhysAddress

Specifies that the ifPhysAddress variation object is not supported.

Max-Access: read-only

Access: not implemented

ifAdminStatus

INTEGER
{ up(1),
down(2) }

Integer {up (1), ready to pass packets down; (2), testing; (3) in some test mode}

Specifies that the ifAdminStatus variation object cannot be written for the ATM interface, which is identified by the ifType value atm(37). The ifAdminStatus variation object does not support the value testing(3).

Max-Access: read-write

Access: read-write

ifOperStatus

INTEGER
{ up(1), down(2),
notPresent(6) }

Integer {up (1), ready to pass packets; down(2); testing (3), in some test mode; unknown (4), status can not be determined; dormant (5); notPresent (6), some component is missing; lowerLayerDown (7), down due to state of lower-layer interface(s)}

Specifies that the ifOperStatus variation object cannot detect all states. This variation object does not support the values testing(3), unknown(4), dormant(5), and lowerLayerDown(7).

Max-Access: read-only

ifLastChange

none

TimeTicks

Specifies that the value cannot reflect the change in the operational status of the interface.

Max-Access: read-only

Access: read-only

ifLinkUpDownTrapEnable

none

Integer
{enabled (1),
disabled (2)}

Specifies that the write operation is not supported.

The default value is disabled.

Max-Access: read-write

Access: read-only

ifNumber

none

Integer32

Specifies that the ifNumber variation object is not supported.

Max-Access: read-only

Access: not implemented

ifAlias

none

DisplayString (SIZE(0..64))

Specifies that the ifAlias variation object is not supported.

Max-Access: read-write

Access: not implemented


Cisco IF Capabilities Used for AXSM-E

The ifGeneralInformationGroup is the object group applicable to Cisco IF capabilities used for AXSM-E. These capabilities reside in the CISCO-AXSME-IF-CAPABILITY.my file.

For a more detailed description, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-18.

Table 8-18 Cisco AXSM-E IF Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

ifTableLastChange

none

TimeTicks

Specifies that the ifTableLastChange variation object is not supported.

Access: not-implemented

ifPhysAddress

none

PhysAddress

Specifies that the ifPhysAddress variation object is not supported.

Access: not-implemented

ifAdminStatus

INTEGER {
up(1),
down(2)
}

INTEGER {
up(1), -- ready to pass packets
down(2),
testing(3) -- in some test mode
}

Specifies that the value testing(3) is not supported.

ifOperStatus

INTEGER {
up(1),
down(2),
notPresent(6),
lowerLayerDown(7)
}

Integer {up (1), ready to pass packets; down(2);
testing (3), in some test mode;
unknown (4), status can not be determined; dormant (5);
notPresent (6), some component is missing; lowerLayerDown (7), down due to state of lower-layer interface(s)}

Specifies that the ifOperStatus variation object is unable to detect all states. The values testing(3), unknown(4), and dormant(5) are not supported.

ifLastChange

none

TimeTicks

Specifies that the ifLastChange variation object always returns a value zero.

ifLinkUpDownTrapEnable

none

INTEGER { enabled(1), disabled(2) }

Specifies that the write operation is not supported.

The default value is disabled.

Access: read-only

ifNumber

none

Integer32

Specifies that the ifNumber variation object is not supported.

Access: not-implemented

ifAlias

none

DisplayString (SIZE(0..64))

Specifies that the ifAlias variation object is not supported.

Access: not-implemented


SNMPv2 Capabilities

The following are the object groups applicable to Cisco WAN MGX8800 SNMPv2 capabilities:

•snmpGroup

•systemGroup

•snmpCommunityGroup

•snmpBasicNotificationsGroup

The SNMPv2 capabilities reside in the CISCO-WAN-MGX8800-SNMPV2-CAPABILITY.my file.

For a more detailed description, see "PXM MIB Objects."

The variation type of MIB objects are listed in Table 8-19.

Table 8-19 Cisco WAN MGX8800 SNMPv2 Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

sysName

DisplayString (SIZE(1..32))

DisplayString (SIZE (0..255))

Determines that the maximum length of the string is 32.

Max-Access: read-write

sysORLastChange

none

TimeStamp

Specifies that the sysORLastChange variation object is not supported.

Max-Access: read-only

Access: not implemented

sysORID

none

OBJECT IDENTIFIER

Specifies that the sysORID variation object is not supported.

Max-Access: read-only

Access: not implemented

sysORUpTime

none

TimeStamp

Specifies that the sysORUpTime variation object is not supported.

Max-Access: read-only

Access: not implemented

sysORDescr

none

DisplayString

Specifies that the sysORDescr variation object is not supported.

Max-Access: read-only

Access: not implemented


PNNI Capabilities

The following are the object groups applicable to the CISCO-WAN-PNNI-CAPABILITY.my file:

•pnniGeneralMinGroup

•pnniGeneralBorderGroup

•pnniNodeMinGroup

•pnniNodePglMinGroup

•pnniNodePglLgnGroup

•pnniSummaryAddressLgnGroup

•pnniLinkMinGroup

•pnniNodeTimerMinGroup

•pnniNodeSvccLgnGroup

•pnniScopeMinGroup

For a more detailed description, see "PNNI MIB Objects."

The variation type of MIB objects are listed in Table 8-20.

Table 8-20 Cisco WAN PNNI Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

pnniNodeDomainName

none

DisplayString

Specifies that the pnniNodeDomainName variation object is not supported.

Max-Access: read-create

Access: not implemented

pnniNodeRowStatus

INTEGER { active(1), createAndGo(4), destroy(6) }

RowStatus

Specifies that the values notInService(2), createAndWait(5), and notReady(3) are not supported. The value active(1) is not supported for a write operation.

Max-Access: read-create

pnniSummaryAddressRow
Status

INTEGER { active(1),
createAndGo(4),
destroy(6) }

RowStatus

Specifies that the values notInService(2), createAndWait(5), and notReady(3) are not supported. The value active(1) is not supported for a write operation.

Max-Access: read-create


RS-232 Capabilities

The following are the object groups applicable to the CISCO-WAN-RS-232-CAPABILITY.my file:

•rs232Group

•rs232AsyncGroup

For a more detailed description, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-21.

Table 8-21 Cisco WAN RS-232 Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

rs232PortType

INTEGER { rs232(2) }

INTEGER
{ other(1),
rs232(2),
rs422(3),
rs423(4),
v35(5),
x21(6) }

Specifies that the values other(1), rs422(3), rs423(4), v35(5), and x21(6) are not supported.

Max-Access: read-only

rs232PortInSigNumber

none

Integer32

Specifies that the rs232PortInSigNumber variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232PortOutSigNumber

none

Integer32

Specifies that the rs232PortOutSigNumber variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232PortInSpeed

Integer32

Integer32

Supports values 2400, 9600 and 192000.

Max-Access: read-write

rs232PortOutSpeed

Integer32

Integer32

Supports values 2400, 9600 and 192000.

Max-Access: read-write

rs232PortInFlowType

INTEGER {ctsRts(2) }

INTEGER { none(1), ctsRts(2), dsrDtr(3)}

Specifies that the values none(1) and dsrDtr(3) are not supported.

Max-Access: read-write

rs232PortOutFlowType

INTEGER {ctsRts(2) }

INTEGER { none(1), ctsRts(2), dsrDtr(3)}

Specifies that the values none(1) and dsrDtr(3) are not supported.

Max-Access: read-write

rs232AsyncPortStopBits

INTEGER {one(1), two(2), oneAndHalf(3) }

INTEGER { one(1), two(2), oneAndHalf(3), dynamic(4) }

Specifies that the value dynamic(4) is not supported.

Max-Access: read-write

rs232InSigPortIndex

none

InterfaceIndex

Specifies that the rs232InSigPortIndex variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232InSigName

none

INTEGER { rts(1), cts(2), dsr(3), dtr(4), ri(5),
dcd(6), sq(7), srs(8), srts(9),
scts(10), sdcd(11) }

Specifies that the rs232InSigName variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232InSigState

none

INTEGER { none(1), on(2), off(3) }

Specifies that the rs232InSigState variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232InSigChanges

none

Counter32

Specifies that the rs232InSigChanges variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232OutSigPortIndex

none

InterfaceIndex

Specifies that the rs232OutSigPortIndex variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232OutSigName

none

INTEGER { rts(1), cts(2), dsr(3), dtr(4), ri(5),
dcd(6), sq(7), srs(8), srts(9),
scts(10), sdcd(11) }

Specifies that the rs232OutSigName variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232OutSigState

none

INTEGER
{ none(1), on(2),
off(3) }

Specifies that the rs232OutSigState variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232OutSigChanges

none

Counter32

Specifies that the rs232OutSigChanges variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232AsyncPortStopBits

INTEGER
{ one(1), two(2), oneAndHalf(3) }

INTEGER
{one(1), two(2),
oneAndHalf(3), dynamic(4) }

Specifies that the dynamic(4) value is not supported.

Max-Access: read-write

rs232AsyncPortAutobaud

none

INTEGER { enabled(1), disabled(2) }

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

rs232AsyncPortParityErrs

none

Counter32

Specifies that the rs232AsyncPortParityErrs variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232AsyncPortFraming
Errs

none

Counter32

Specifies that the rs232AsyncPortFramingErrs variation object is not supported.

Max-Access: read-only

Access: not implemented

rs232AsyncPortOverrun
Errs

none

Counter32

Specifies that the rs232AsyncPortOverrunErrs variation object is not supported.

Max-Access: read-only

Access: not implemented


Cisco WAN Resource Partition Capabilities

The following are the object groups applicable to the CISCO-WAN-RSRC-PART-CAPABILITY.my file:

•cwRsrcPartMIBGroup

•cwRsrcPartIlmiMIBGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-22.

Table 8-22 Cisco WAN Resource Partition Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwRsrcPartID

Unsigned32(1..20)

Unsigned32 (1.. 255)

Supports the maximum value of 20.

Max-Access: not-accessible

cwRsrcPartController

Unsigned32(1..20)

Unsigned32 (1.. 255)

Supports the maximum value of 20.

Max-Access: not-accessible

cwRsrcPartRowStatus

INTEGER
{ active(1), notInService(2),
createAndGo(4),
destroy(6)}

RowStatus

Specifies that the value createAndWait(5) is not supported.

Max-Access: read-create


Cisco WAN Resource Partition Capabilities for RPM

This section describes the agent capabilities that support the Cisco WAN Resource Partition MIB for RPM.

The cwRsrcPartMIBGroup is the object group applicable to the CISCO-WAN-RPM-RSRC-PART-CAPABILITY.my file.

For a more detailed description, see"Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-23.

Table 8-23 Cisco WAN Resource Partition Capabilities for RPM 

Variation Name
Capability Syntax
MIB Syntax
Description

cwRsrcPartID

Unsigned32 (1..10)

Unsigned32 (1.. 255)

Specifies that a limited range is supported. The value 1 is reserved for the PNNI controller.

cwRsrcPartController

none

Unsigned32 (1.. 255)

Specifies that the value 2 is assumed to be the PNNI controller.

cwRsrcPartEgrGuarPctBwConf

none

Unsigned32 (0..1000000)

Specifies that the cwRsrcPartEgrGuarPctBwConf variation object supports only a whole percentage, for example, 1 percent, 10 percent, and so forth.

cwRsrcPartEgrMaxPctBwConf

none

Unsigned32 (0..1000000)

Specifies that the cwRsrcPartEgrMaxPctBwConf variation object supports only a whole percentage, for example, 1 percent, 10 percent, and so forth.

cwRsrcPartIngGuarPctBwConf

none

Unsigned32 (0..1000000)

Specifies that the cwRsrcPartIngGuarPctBwConf variation object supports only a whole percentage, for example, 1 percent, 10 percent, and so forth.

cwRsrcPartIngMaxPctBwConf

none

Unsigned32 (0..1000000)

Specifies that the cwRsrcPartIngMaxPctBwConf variation object supports only a whole percentage, for example, 1 percent, 10 percent, and so forth.

cwRsrcPartVpiLo

Unsigned32 (0..255)

Unsigned32 (0..4095)

Supports the restricted range.

For VCC partition, the value 0 is supported. For VPC partition, the range is from 1 to 255.

cwRsrcPartVpiHigh

Unsigned32 (0..255)

Unsigned32 (0..4095)

Supports the restricted range.

For a VCC partition, the value 0 is supported. For a VPC partition, the valid range is from
1 to 255.

cwRsrcPartVciLo

Unsigned32 (1..65535)

Unsigned32 (0..65535)

Supports the restricted range.

For a VCC partition, the valid range is from
1 to 3808. For a VPC partition, the valid range is from 0 to 65535.

cwRsrcPartVciHigh

Unsigned32 (1..65535)

Unsigned32 (0..65535)

Supports the restricted range.

For a VCC partition, the valid range is from
1 to 3808. For a VPC partition, the valid range is from 0 to 65535.

cwRsrcPartGuarCon

none

Unsigned32 (0..131072)

Specifies that write operation is not supported.

Access: read-only

cwRsrcPartMaxCon

none

Unsigned32 (0..131072)

Specifies that write operation is not supported.

Access: read-only

cwRsrcPartRowStatus

INTEGER {
active(1),
createAndGo(4),
destroy(6)
}

RowStatus

Specifies that the cwRsrcPartRowStatus variation object does not support notInService(2), notReady(3), and createAndWait(5).


SONET Capabilities

The following are the object groups applicable to the CISCO-WAN-SONET-CAPABILITY.my file:

•sonetMediumStuff2

•sonetSectionStuff2

•sonetLineStuff2

•sonetPathStuff2

•sonetFarEndLineStuff2

•sonetFarEndPathStuff2

For a more detailed description, see "Standard MIB Objects."

The variation type of MIB objects are listed in Table 8-24.

Table 8-24 Cisco WAN SONET Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

sonetPathCurrentWidth

none

INTEGER { sts1(1), sts3cSTM1(2), sts12cSTM4(3), sts24c(4), sts48cSTM16(5) }

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

sonetMediumLineCoding

none

INTEGER {sonetMediumOther(1), sonetMediumB3ZS(2), sonetMediumCMI(3), sonetMediumNRZ(4), sonetMediumRZ(5) }

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

sonetMediumLineType

none

INTEGER
{sonetOther(1), sonetShortSingleMode(2), sonetLongSingleMode(3), sonetMultiMode(4), sonetCoax(5), sonetUTP(6)}

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

sonetMediumCircuit
Identifier

none

DisplayString (SIZE (0..255))

Specifies that write access is not supported.

Max-Access: read-write

Access: read-only

sonetMediumLoopback
Config

none

BITS {sonetNoLoop(0), sonetFacilityLoop(1), sonetTerminalLoop(2), sonetOtherLoop(3)}

Specifies that the variation object is not supported.

Max-Access: read-write

Access: not implemented


Cisco WAN SVC Capabilities

The following are the object groups applicable to the CISCO-WAN-SVC-CAPABILITY.my file:

•cwsInfoGrp

•cwspConfigGrp

•cwspCacConfigGrp

•cwspCallStatsGrp

•cwspSigStatsGrp

•cwspCallGrp

•cwspAbrCallGrp

•cwspLoadGrp

•cwspAddressGrp

•cwspConnTraceGrp

•cwspOperationGrp

•cwspSpvcGrp

For a more detailed description, see "PNNI MIB Objects."

The variation type of MIB objects are listed in Table 8-25.

Table 8-25 Cisco WAN SVC Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwspConfigTableRowStatus

INTEGER
{active(1),
createAndGo(4),
destroy(6)}

RowStatus

Specifies that the values notInService(2), notReady(3), and createAndWait(5) are not supported.

Max-Access: read-create

cwspAddressRowStatus

INTEGER
{active(1),
createAndGo(4),
destroy(6)}

RowStatus

Specifies that the values notInService(2) and createAndWait(5) are not supported. The value active(1) cannot beset.

Max-Access: read-create

cwspConnTraceQueryStatus

INTEGER
{active(1),
createAndGo(4),
destroy(6)}

RowStatus

Specifies that the values notInService(), notReady(3), and createAndWait(5)are not supported. The value active(1) cannot be set.

Max-Access: read-create

cwspSpvcNodePrefix

none

none

Specifies that the write operation is not supported.

Access: read-only

cwspMaxP2pCalls

none

Integer32 (0..65535)

Specifies that the write operation is not supported.

Max-Access: read-create

Access: read-only


Cisco System Capabilities

This section describes the agent capabilities that support the Cisco System MIB.

The following are the object groups applicable to the CISCO-WAN-SYSTEM-CAPABILITY.my file:

•ciscoSystemClockGroup

•ciscoSystemLocationGroup

The agent capabilities for Cisco System does not contain any variation objects.

Cisco AXSM Cisco SONET Capabilities

This section describes the agent capabilities that support the Cisco SONET MIB.

The following are the object groups applicable to the CISCO-AXSM-CISCO-SONET-CAPABILITY.my file:

•ciscoSonetConfMIBGroup

•ciscoSonetStatsMIBGroup

•ciscoSonetTraceMIBGroup

•ciscoSonetApsMIBGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-26.

Table 8-26 Cisco AXSM Cisco SONET Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

csConfigFrame
Scramble

INTEGER
{ enabled(2) }

INTEGER
{disabled(1),
enabled(2)}

Specifies the value disabled(1) is not supported.

csApsWaitToRestore

Unsigned32(5..12)

Unsigned32 (1..12) in units of minutes

Determines the wait to restore time interval is between 5 to 12 minutes.

csApsArchMode

INTEGER {
onePlusOne(1),
oneToOne(2)}

INTEGER {onePlusOne(1), oneToOne(2), anexBOnePlusOne(3), ycableOnePlusOneNok1k2(4), straightOnePlusOneNok1k2(5)}

Specifies the values anexBOnePlusOne(3), ycableOnePlusOneNok1k2(4), straightOnePlusOneNok1k2(5) are not supported.

cssTraceReceived

none

OCTET STRING
(SIZE (0|16|64))

Specifies the cssTraceReceived variation object is not supported.

Access: not implemented

cspTraceReceived

none

OCTET STRING (SIZE(0|16|64))

Specifies the cspTraceReceived variation object is not supported.

Access: not implemented


Cisco AXSM-E Cisco SONET Capabilities

The following are the object groups applicable to the CISCO-AXSME-CISCO- SONET-CAPABILITY.my file for AXSM-E:

•ciscoSonetConfMIBGroup

•ciscoSonetStatsMIBGroup

•ciscoSonetTraceMIBGroup

•ciscoSonetApsMIBGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-27.

Table 8-27 Cisco AXSM-E Cisco SONET Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

csConfigFrame
Scramble

INTEGER {
enabled(2)
}

INTEGER {
disabled(1),
enabled(2)
}

Specifies that the value disabled(1) is not supported.

csApsArchMode

INTEGER {
onePlusOne(1),
oneToOne(2),
anexBOnePlusOne(3),
straightOnePlusOne
Nok1k2(5)
}

INTEGER {
onePlusOne(1),
oneToOne(2),
anexBOnePlusOne(3),
ycableOnePlusOneNok1k2(4),
straightOnePlusOneNok1k2(5)
}

Specifies that the value ycableOnePlusOneNok1k2(4) is not supported.

csApsDirection

none

INTEGER {
uniDirectional(1),
biDirectional(2)
}

Specifies that the value uniDirectional(1) is ignored for the following scenarios:

•csApsArchMode equals to annexBOnePlusOne(3)

•csApsChannelProtocol equals to itu(2)

csApsRevertive

none

INTEGER {
nonrevertive(1),
revertive(2)
}

Specifies that the value revertive(2) is ignored for the following scenarios:

•csApsArchMode equals to annexBOnePlusOne(3)

•csApsChannelProtocol equals to itu(2)

cssTraceReceived

none

OCTET STRING (SIZE(0|16|64))

Specifies that the cssTraceReceived variation object is not supported.

Access: not-implemented

cspTraceReceived

none

OCTET STRING (SIZE(0|16|64))

Specifies that the cspTraceReceived variation object is not supported.

Access: not-implemented


Cisco AXSM WAN Module Capabilities

This section describes the agent capabilities that support the Cisco WAN Module MIB.

The following are the object groups applicable to the CISCO-AXSM-WAN-MODULE-CAPABILITY.my file:

•cwmConfigGroup

•ConfigGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-28.

Table 8-28 Cisco AXSM WAN Module Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwmIngressSCTFileName

none

DisplayString

Specifies the cwmIngressSCTFileName variation object is not supported.

Access: not implemented

cwmAutoLineDiagEnable

none

INTEGER { enable(1), disable(2) }

Specifies the cwmAutoLineDiagEnable variation object is not supported.

Access: not implemented

cwmStatBucketInterval

none

INTEGER { five(5), ten(10), fifteen(15), twenty(20), thirty(30), sixty(60) }

Sets the default to value fifteen(15).

cwmStatCollectionInterval

none

INTEGER { default(0), one(1), five(5) }

Specifies the cwmStatCollectionInterval variation object is not supported.

Access: not implemented

cwmStatCollectionStatus

none

INTEGER { enable(1), disable(2) }

Specifies the cwmStatCollectionStatus variation object is not supported.

Access: not implemented

cwmStatCurrentLevel

none

StatisticsLevel

Specifies the cwmStatCurrentLevel variation object is not supported.

Access: not implemented

cwmStatLevelConfigured

none

StatisticsLevel

Specifies the cwmStatLevelConfigured variation object is not supported.

Access: not implemented

cwmStatMaximum
Connections

none

Unsigned32

Specifies the cwmStatMaximumConnections variation object is not supported.

Access: not implemented


Cisco AXSM-E WAN Module Capabilities

This section describes the agent capabilities that support the Cisco WAN Module MIB for AXSM-E.

The following are the object groups applicable to the CISCO-AXSME-WAN-MODULE-CAPABILITY.my file:

•cwmConfigGroup

•cwmStatConfigGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of MIB objects are listed in Table 8-29.

Table 8-29 Cisco AXSM-E WAN Module Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwmIngressSCTFileName

none

DisplayString

Specifies that the cwmIngressSCTFileName variation object is not supported.

Access: not-implemented

cwmStatCollectionStatus

none

INTEGER {
enable(1),
disable(2)
}

Specifies that the cwmStatCollectionStatus variation object is not supported.

Access: not-implemented


Cisco AXSM-E ATM Cell Layer Capabilities

This section describes the agent capabilities that support the Cisco ATM Cell Layer MIB for AXSM-E.

The following are the object groups applicable to the CISCO-AXSME-ATM-CELL-LAYER-CAPABILITY.my file:

•caclATMSwitchStatsMIBGroup

•caclATMEndSyatemStatsMIBGroup

•caclIntervalStatsMIBGroup

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of objects are listed in Table 8-30.

Table 8-30 Cisco AXSM-E ATM Cell Layer Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

caclInXmtCLP0Cells

none

Counter32

Specifies the caclInXmtCLP0Cells variation object is not supported.

Access: not-implemented

caclInXmtCLP1Cells

none

Counter32

Specifies the caclInXmtCLP1Cells variation object is not supported.

Access: not-implemented

caclInUpcCLP0DiscCells

none

Counter32

Specifies the caclInUpcCLP0DiscCells variation object is not supported.

Access: not-implemented

caclInUpcTotalDiscCells

none

Counter32

Specifies the caclInUpcTotalDiscCells variation object is not supported.

Access: not-implemented

caclInUpcTotalNonComp
Cells

none

Counter32

Specifies the caclInUpcTotalNonCompCells variation object is not supported.

Access: not-implemented

caclOutXmtCLP0Cells

none

Counter32

Specifies the caclOutXmtCLP0Cells variation object is not supported.

Access: not-implemented

caclOutXmtCLP1Cells

none

Counter32

Specifies the caclOutXmtCLP1Cells variation object is not supported.

Access: not-implemented

caclOutRcvIdleCells

none

Counter32

Specifies the caclOutRcvIdleCells variation object is not supported.

Access: not-implemented

caclOutVpiVciErrCells

none

Counter32

Specifies the caclOutVpiVciErrCells variation object is not supported.

Access: not-implemented

caclIntervalInXmtCLP0
Cells

none

Gauge32

Specifies the caclIntervalInXmtCLP0Cells variation object is not supported.

Access: not-implemented

caclIntervalInXmtCLP1
Cells

none

Gauge32

Specifies the caclIntervalInXmtCLP1Cells variation object is not supported.

Access: not-implemented

caclIntervalInUpcCLP0
DiscCells

none

Gauge32

Specifies the caclIntervalInUpcCLP0Disc
Cells variation object is not supported.

Access: not-implemented

caclIntervalInUpcTotalDiscCells

none

Gauge32

Specifies the caclIntervalInUpcTotalDisc
Cells variation object is not supported.

Access: not-implemented

caclIntervalInUpcTotNon
CmpCells

none

Gauge32

Specifies the caclIntervalInUpcTotNonCmp
Cells variation object is not supported.

Access: not-implemented

caclIntervalOutXmtCLP0
Cells

none

Gauge32

Specifies the caclIntervalOutXmtCLP0Cells variation object is not supported.

Access: not-implemented

caclIntervalOutXmtCLP1
Cells

none

Gauge32

Specifies the caclIntervalOutXmtCLP1Cells variation object is not supported.

Access: not-implemented

caclIntervalOutRcvIdle
Cells

none

Gauge32

Specifies the caclIntervalOutRcvIdleCells variation is not supported.

Access: not-implemented

caclIntervalOutVpiVciErrCells

none

Gauge32

Specifies the caclIntervalOutVpiVciErrCells variation is not supported.

Access: not-implemented


Cisco AXSM-E ATM Connection Statistics Capabilities

This section describes the agent capabilities that support the Cisco WAN ATM Connection Statistics MIB for AXSM-E.

The cwacsGroup is the object groups applicable to the CISCO-AXSME-ATM-CONN-STAT-CAPABILITY.my file.

For a more detailed description, see "Cisco Enterprise MIB Objects."

The variation type of objects are listed in Table 8-31.

Table 8-31 Cisco AXSM-E ATM Connection Statistics Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwacsIngRcvEFCI0

none

Counter32

Specifies that the cwacsIngRcvEFCI0 variation object is not supported.

Access: not-implemented

cwacsIngEFCI0Discard

none

Counter32

Specifies that the cwacsIngEFCI0Discard variation object is not supported.

Access: not-implemented

cwacsIngXmtFRm

none

Counter32

Specifies that the cwacsIngXmtFRm variation object is not supported.

Access: not-implemented

cwacsIngXmtBRmFsRm

none

Counter32

Specifies that the cwacsIngXmtBRmFsRm variation object is not supported.

Access: not-implemented

cwacsEgrRcvEFCI0

none

Counter32

Specifies that the cwacsEgrRcvEFCI0 variation object is not supported.

Access: not-implemented

cwacsEgrEFCI0Discard

none

Counter32

Specifies that the cwacsEgrEFCI0Discard variation object is not supported.

Access: not-implemented

cwacsEgrXmtFRm

none

Counter32

Specifies that the cwacsEgrXmtFRm variation object is not supported.

Access: not-implemented

cwacsEgrXmtBRmFsRm

none

Counter32

Specifies that the cwacsEgrXmtBRmFsRm variation object is not supported.

Access: not-implemented

cwacsEgrRcvEOF1

none

Counter32

Specifies that the cwacsEgrRcvEOF1 variation object is not supported.

Access: not-implemented


Cisco WAN RPM Subinterface Capabilities

This section describes the agent capabilities that support the Cisco WAN RPM Subinterface MIB for RPM.

The ciscoWanRpmSubIfMIBGroup2 is the object group applicable to the CISCO-WAN-RPM-SUBIF-CAPABILITY.my file.

The variation type of MIB objects are listed in Table 8-32.

Table 8-32 Cisco WAN RPM Subinterface Capabilities 

Variation Name
Capability Syntax
MIB Syntax
Description

cwrSubIfAdapterIf

Unsigned32(1..1)

Unsigned32

Supports value 1 only.

cwrSubIfRowStatus

INTEGER {
active(1), notInService(2),
createAndGo(4),
destroy(6)
}

RowStatus

Specifies that the cwrSubIfRowStatus variation object does not support notReady(3) and createAndWait(5).


Was this Document Helpful?

FeedbackFeedback

Contact Cisco

This Document Applies to These Products