Cisco.com Worldwide

Table 1. Connectors-Feature Support
Features/Apps	Cisco DNA Spaces Connector	Cisco WLC Direct Connect (Recommended only for small scale deployments) Cisco Wireless Controller Cisco Catalyst 9800 Controller	Cisco CMX Tethering Connector
Cisco DNA Spaces dashboard	Supported	Supported	Supported
Captive Portals	Supported	Supported	Supported
Engagements	Supported	Supported	Supported
Location Personas	Supported	Supported	Supported
Location Analytics	Supported	Supported	Supported
Impact Analysis	Supported	Supported	Supported
Behaviour Metrics	Supported	Supported	Supported
Operational Insights	Supported	Not Supported	Supported
Open Roaming	Supported	Not Supported	Not Supported
IoT Services	Supported	Not Supported	Not Supported
Detect and Locate	Supported	Limited Support (Associated Clients only)	Supported
Hyperlocation	Supported	Not Supported	Supported
Fastlocate	Supported	Not Supported	Supported
Scale Support For more details, see the scale summary in Cisco DNA Spaces Scale Benchmark.	Best suited for scaling	Scale supported for AireOS Controller 8.8 MR2 and Cisco Catalyst 9800 Series 16.12.1. Up to 50 clients.	Supports the scale that Cisco CMX can handle.
AireOS Controller Platform Support	Supported	Supported	Supported
Cisco Catalyst 9800 Platform Support	Supported	Supported	Supported

Connecting Cisco DNA Spaces to Cisco Wireless Controller through Cisco CMX

To connect Cisco DNA Spaces with Cisco Wireless Controllers through Cisco CMX, you must have Cisco CMX 10.6 or later.

For Cisco Unified Wireless Network with Cisco CMX, the following configurations are required to work with Cisco DNA Spaces:

Note

The configuration for internet provisioing and RADIUS authentication is required only if you need radius-authentication. This configuration is required only if you need social authentication for your portals.

Configuring Access Point Mode, SSIDs, ACLs, Splash URLs, and Virtual Interface in the WLC

To create a Captive Portal rule, you must initially define the mode for access points, and create the SSIDs and ACLs in the Cisco Wireless Controller. You must also ensure that the splash URL for the SSID is configured in the Cisco Wireless Controller.

Note

The SSIDs and ACLs are created in the Cisco Wireless Controller and not in the Cisco CMX.

The Cisco Wireless Controller configurations for the local and flexconnect modes are different.

Note

The configurations are done in the Cisco Wireless Controller that is not a part of Cisco DNA Spaces, and the menu path and names specified for the tabs, windows, options, and so on in this documentation are subject to change.

Local Mode Configurations for Using Cisco DNA Spaces

To configure the Cisco Wireless Controller to use with Cisco DNA Spaces in the local mode, perform the following steps:

Configure the Local Mode for an Access Point

To configure a local mode for an access point, perform the following steps:

Procedure

Step 1	Log in to the Cisco Wireless Controller with your Wireless Controller credentials.
Step 2	In the Cisco Wireless Controller main window, click the Wireless tab. All of the access points are listed.
Step 3	Click the access point for which you want to configure the mode to local.
Step 4	Click the General tab.
Step 5	From the AP Mode drop-down list, choose Local, and click Apply.

Create SSIDs in Cisco Wireless Controller

Note

The SSIDs are created in the Cisco Wireless Controller, not in the Cisco CMX.

To create the SSIDs in the Cisco Wireless Controller, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller main window, click the WLANs tab.

Step 2

To create a WLAN, choose Create New from the drop-down list at the right side of the window, and click Go.

Step 3

In the New window that appears, enter the WLAN details like Type, Profile Name, SSID, and so on.

Step 4

Click Apply.

The Edit <SSID Name> window appears.

Step 5

Add the SSID to the Cisco DNA Spaces dashboard.

Step 6

In the Cisco Wireless Controller main window, on the General tab, uncheck the Broadcast SSID check box.

Note

The SSID Broadcasting is interrupted to avoid any customer accessing the SSID before completing the configurations.

Step 7

Choose Security > Layer 2, and check the MAC Filtering check box.

Step 8

In the Layer 3 tab, do the following configurations:

From the Layer 3 security drop-down list, choose Web Policy.

Note

Web Policy is the Layer 3 security option that enables you to configure captive portal in the Cisco Wireless Controller.

Choose the On Mac Filter Failure radio button.
In the Preauthentication ACL area, from the IPv4 drop-down list, choose the ACL previously defined.

Check the Enable check box for the Sleeping Client.

Note

Enabling sleeping client is not mandatory. But if enabled, the customer who is in sleeping mode after authentication gets connected without authentication if is waken up within the specified time. The clients with guest access that had successful web authentication are allowed to sleep and wake up without having to go through another authentication process through the login page. You can configure the duration for which the sleeping clients are to be remembered for before re-authentication becomes necessary. The valid range is 1 hour to 720 hours (30 days), with the default being 12 hours. Ideally, this should be similar to session timeout.

Check the Enable check box for the Override Global Config.

Note

Enabling Override global config allows you to redirect the customer to the Cisco DNA Spaces URL, which is an external URL.

From the Web Auth Type drop-down list, choose External (Redirect to External Server).

Note

The Web Auth Type must be External as the Cisco DNA Spaces page is hosted in the external server, and not in the controller.

In the URL field that appears, enter the Cisco DNA Spaces splash URL.

To view the splash URL for your CUWN or AireOS account, in the Cisco DNA Spaces dashboard, the Configure Manually link for a AireOS SSID in the SSIDs window. The Configure Manually link appears only after adding a Cisco AireOS SSID.

Note

You must configure the splash page for the customer to be redirected to the Cisco DNA Spaces web page during on-boarding.

Click Apply.

Step 9

Click the Advanced tab.

Step 10

In the Enable Session Timeout field, enter the required session timeout value in seconds. For example, for session timeout of 30 minutes, enter 1800.

Step 11

Click Apply.

Step 12

In the General tab, check the Enabled check box for the Status and Broadcast SSID options, to enable the SSID.

Step 13

Execute the following command in the command prompt to disable captive bypassing. Then, restart the Cisco Wireless Controller.

config network web-auth captive-bypass disable Management > HTTP-HTTPS

Note

If captive bypassing is enabled, the CNA will not pop up for iOS devices.

Step 14

In the HTTP-HTTPS configuration window that appears, do the following:

From the HTTP Access drop-down list, choose Disabled.
From the HTTPS Access drop-down list, choose Enabled.
From the WebAuth SecureWeb drop-down list, choose Disabled.
Click Apply.

Step 15

Choose Security > Web Auth > Web Login Page, and ensure that the Redirect URL after login field is blank.

Note

The redirect URL field must be blank so that it won’t override the Cisco DNA Spaces splash URL configured in Layer 3.

What to do next

Note

If you have made any changes to the Management tab, then restart your Cisco Wireless Controller for the changes to take effect.

Create Access Control Lists

To restrict the Internet access for customers, and to allow access only to Cisco DNA Spaces splash page URL when connected to the SSID, the Cisco DNA Spaces IPs (wall garden ranges) must be configured in the ACL. Now when a customer connects to the SSID, the splash page appears for the customer.

If ACL is not configured with all the required IPs, the system considers the Cisco DNA Spaces as an external URL, and results into multiple redirection for customer.

To create the access control list, perform the following steps:

Procedure

Step 1

Step 2

Choose Security > Access Control Lists > Access Control Lists.

Step 3

To add an ACL, click New.

Step 4

In the New window that appears, enter the following:.

In the Access Control List Name field, enter a name for the new ACL.

Note

You can enter up to 32 alphanumeric characters.

Choose the ACL type as IPv4.
Click Apply.

Step 5

When the Access Control Lists window reappears, click the name of the new ACL.

Step 6

In the Edit window that appears, click Add New Rule.

The Rules > New window appears.

Step 7

Configure a rule for this ACL with the required wall garden ranges.

To view the wall garden ranges, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a Cisco Unified Wireless Network SSID in the SSIDs window. The wall garden ranges are listed under the caption Creating the Access Control List. The Configure Manually link appears only after adding a Cisco AireOS SSID.

When defining the ACL rule, ensure to configure the values as follows:

Direction: Any
Protocol: Any
Source Port Range: 0-65535
Destination Port Range: 0-65535
DSCP: Any
Action: Permit

Step 8

If you want to provide social authentication for your portal, you must also configure the wall garden ranges for social authentication.

Note

The wall garden ranges configured for social authentication allows the customers to access all the HTTPS web sites directly after connecting to your SSID, without using the captive portal.

Configure the Virtual Interface

To configure the virtual interface, perform the following steps:

Procedure

Step 1

Choose Controller > Interfaces.

Step 2

Click the Virtual link.

Step 3

In the Interfaces > Edit window that appears, enter the following parameters:

In the IP address field, enter the unassigned and unused gateway IP address, if any.

In the DNS Host Name field, enter the DNS Host Name, if any.

Note

Ideally this field must be blank.

Note

To ensure connectivity and web authentication, the DNS server must always point to the virtual interface. If a DNS hostname is configured for the virtual interface, then you must configure the same DNS host name on the DNS servers used by the client.

Click Apply.

Note

If you have made any changes to the virtual interface, restart your Cisco Wireless Controller for the changes to take effect.

FlexConnect Mode Configurations for Using Cisco DNA Spaces

You can configure FlexConnect for central switch or local switch mode.

FlexConnect Central Switch Mode

To configure the Cisco Wireless Controller to use the Cisco DNA Spaces in the FlexConnect central switch mode, perform the following steps:

Configure the FlexConnect Mode for an Access Point

This configuration is applicable for FlexConnect central switch and local switch mode. To configure a FlexConnect Central switch mode for an access point, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller main window, click the Wireless tab.

All of the access points are listed.

Note

For more details on the access points, see the Cisco Wireless Controller user guide.

Step 2

Click the access point for which you want to configure the mode to FlexConnect.

Step 3

Click the General tab.

Step 4

From the AP Mode drop-down list, choose FlexConnect.

Step 5

Click Apply to commit your changes and to cause the access point to reboot.

Create SSIDs in the Cisco Wireless Controller for FlexConnect Central Switch Mode

Create the SSID using the same steps as outlined for the local mode. For more information, see the Create SSIDs in Cisco Wireless Controller.

Create Access Control Lists for FlexConnect Central Switch Mode

Create the Access Control List using the same steps as outlined for the local mode. For more information, see the Create Access Control Lists.

Configure the Virtual Interface

To configure the virtual interface, perform the following steps:

Procedure

Step 1

Choose Controller > Interfaces.

Step 2

Click the Virtual link.

Step 3

In the Interfaces > Edit window that appears, enter the following parameters:

In the IP address field, enter the unassigned and unused gateway IP address, if any.

In the DNS Host Name field, enter the DNS Host Name, if any.

Note

Ideally this field must be blank.

Note

Click Apply.

Note

If you have made any changes to the virtual interface, restart your Cisco Wireless Controller for the changes to take effect.

FlexConnect Local Switch Mode

To configure the Cisco Wireless Controller to use the Cisco DNA Spaces in the FlexConnect local switch mode, perform the following steps:

Configure the FlexConnect Mode for an Access Point

Configure the FlexConnect Mode for an Access Point

This configuration is applicable for FlexConnect central switch and local switch mode. To configure a FlexConnect Central switch mode for an access point, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller main window, click the Wireless tab.

All of the access points are listed.

Note

For more details on the access points, see the Cisco Wireless Controller user guide.

Step 2

Click the access point for which you want to configure the mode to FlexConnect.

Step 3

Click the General tab.

Step 4

From the AP Mode drop-down list, choose FlexConnect.

Step 5

Click Apply to commit your changes and to cause the access point to reboot.

Create SSIDs in the Cisco Wireless Controller for the FlexConnect Local Switch Mode

Note

The SSIDs are created in the Cisco Wireless Controller, not in the Cisco CMX.

To create the SSIDs in the CUWN for the FlexConnect local switch mode, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller main window, click the WLANs tab.

Step 2

To create a WLAN, choose Create Newfrom the drop-down list at the right side of the window, and click Go.

Step 3

In the New window that appears, enter the WLAN details such as, Type, Profile Name, SSID, and so on.

Step 4

Click Apply.

The Edit <SSID Name> window appears.

Step 5

Add the SSID to the Cisco DNA Spaces dashboard.

Step 6

In the Cisco Wireless Controller main window, on the General tab, uncheck the Broadcast SSID check box.

Note

The SSID Broadcasting is interrupted to avoid any customer accessing the SSID before completing the configurations.

Step 7

Choose Security > Layer 2, and check the MAC Filtering check box.

Step 8

In the Layer 3 tab, do the following configurations:

From the Layer 3 security drop-down list, choose Web Policy.

Note

Web Policy is the Layer 3 security option that enables you to configure captive portal in the Cisco Wireless Controller.

Choose the On Mac Filter Failure radio button.
In the Preauthentication ACL area, from the WebAuth FlexACL drop-down list, choose the ACL previously defined.

Check the Enable check box for Sleeping Client.

Note

Enabling sleeping client is not mandatory. But if enabled, the customer who is in sleeping mode after authentication gets connected without authentication if is waken up within the specified time. The clients with guest access that had successful web authentication are allowed to sleep and wake up without having to go through another authentication process through the login window. You can configure the duration for which the sleeping clients are to be remembered for before re-authentication becomes necessary. The valid range is 1 hour to 720 hours (30 days), with the default being 12 hours. Ideally, this should be similar to session timeout.

Check the Enable check box for Override Global Config.

Note

Enabling Override Global Config enables you to redirect the customer to the Cisco DNA Spaces URL, which is an external URL.

From the Web Auth Type drop-down list, choose External.

Note

The Web Auth Type must be External as the Cisco DNA Spaces page is hosted in the external server, and not in the controller.

In the URL field that appears, enter the Cisco DNA Spaces Splash URL.

To view the splash URL for your CUWN account, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a CUWN SSID in the SSIDs window. The Configure Manually link appears only after adding a Cisco AireOS SSID.

Note

You must configure the splash page for the customer to be redirected to the Cisco DNA Spaces web page during on-boarding.

Click Apply.

Step 9

Click the Advanced tab.

Step 10

In the Enable Session Timeout field, enter the required session timeout value in seconds. For example, for session timeout of 30 minutes, enter 1800 .

Step 11

In the FlexConnect area, check the Enabled check box for FlexConnect Local Switching, and click Apply.

Step 12

In the General tab, select the Enabled check box for the Status and Broadcast SSID options, to enable the SSID.

Step 13

Execute the following command in the command prompt to disable captive bypassing. Then, restart the Cisco Wireless Controller.

config network web-auth captive-bypass disable

Note

If captive bypassing is enabled, the CNA will not pop up for iOS devices.

Step 14

Choose Management > HTTP-HTTPS.

Step 15

In the HTTP-HTTPS Configuration window that appears, perform the following:

From the HTTP Access drop-down list, choose Disabled.
From the HTTPS Access drop-down list, choose Enabled.
From the WebAuth SecureWeb drop-down list, choose Disabled.
Click Apply.

Step 16

Choose Security > Web Auth > Web Login Page, and ensure that the Redirect URL after login field is blank.

Note

The redirect URL field must be blank so that it will not override the Cisco DNA Spaces splash URL configured in Layer 3.

Create Access Control Lists for FlexConnect Local Switch Mode

If ACL is not configured with all the required IPs, the system considers the Cisco DNA Spaces as an external URL, and results into multiple redirection for customer.

To create the access control list for the FlexConnect local switch mode, perform the following steps:

Procedure

Step 1

Step 2

Choose Security > Access Control Lists > FlexConnect ACLs.

Step 3

To add an ACL, click New.

Step 4

In the New window that appears, enter the following:

In the Access Control List Name field, enter a name for the new ACL.

Note

You can enter up to 32 alphanumeric characters.

Click Apply.

Step 5

When the Access Control Lists window reappears, click the name of the new ACL.

Step 6

In the Edit window that appears, click Add New Rule.

The Rules > New window appears.

Step 7

Configure a rule for this ACL with the required wall garden ranges.

To view the wall garden ranges, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a CUWN SSID in the SSIDs window.”.

When defining the ACL rule, ensure to configure the values as follows:

Direction: Any
Protocol: Any
Source Port Range: 0-65535
Destination Port Range: 0-65535
DSCP: Any
Action: Permit

Step 8

If you want to provide social authentication for your portal, you must also configure the wall garden ranges for social authentication. To know the wall garden ranges that you must configure for social authentication, see the “Configuring the Wireless Network for Social Authentication” section.

Note

The wall garden ranges configured for social authentication allows the customers to access all the HTTPS web sites directly after connecting to your SSID, without using the captive portal.

Configure the Virtual Interface

To configure the virtual interface, perform the following steps:

Procedure

Step 1

Choose Controller > Interfaces.

Step 2

Click the Virtual link.

Step 3

In the Interfaces > Edit window that appears, enter the following parameters:

In the IP address field, enter the unassigned and unused gateway IP address, if any.

In the DNS Host Name field, enter the DNS Host Name, if any.

Note

Ideally this field must be blank.

Note

Click Apply.

Note

If you have made any changes to the virtual interface, restart your Cisco Wireless Controller for the changes to take effect.

Configuring Cisco Wireless Controller for Internet Provisioning and RADIUS Authentication

We highly recommend to use RADIUS authentication for captive portals. The following features work only if you configure RADIUS authentication.

Seamless Internet Provisioning.
Extended session duration and Internet bandwidth.
Deny Internet.

Also, for Customer onboarding by captive portal, internet provisioning configuration is required.

To configure radius authentication and seamless internet provisioning, perform the following steps:

Procedure

Step 1

Step 2

In the Cisco Wireless Controller main window, click the Security tab.

Step 3

Choose Radius > Authentication.

The Radius Authentication Servers window appears.

Step 4

From the Auth Called Station ID Typee drop-down list, choose AP MAC Address:SSID.

Step 5

From the MAC Delimiter drop-down list, choose Hyphen.

Step 6

Click New.

Step 7

In the New window that appears, enter the details of the radius server for authentication, such as server IP address, port number, and secret key, select the Server Status as Enabled, and click Apply.

Port Number: 1812

Note

You can configure only the Cisco DNA Spaces radius servers.To view the radius server IP address and secret key, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a CUWN SSID in the SSIDs window. The Configure Manually link appears only after adding a Cisco AireOS SSID. Configure both the primary and secondary radius server IPs. You can also contact the Cisco DNA Spaces support team.

Step 8

Choose Radius > Accounting.

The Radius Accounting Servers window appears.

Step 9

From Acct Called Station ID Type, choose AP MAC Address:SSID.

Step 10

From the MAC Delimiter drop-down list, choose Hyphen.

Step 11

Click New.

Step 12

In the New window that appears, enter the details of the radius server for accounting, such as server IP address, port number, and secret key, select the Server Status as Enabled, and click Apply.

Port Number: 1813

Note

You can configure only the Cisco DNA Spaces radius servers. You can configure only the Cisco DNA Spaces radius servers. To view the radius server IP address and secret key, in the Cisco DNA Spaces dashboard, click the “Configure Manually” link for a CUWN SSID in the SSIDs window.

Step 13

In the Cisco Wireless Controller main window, click the WLANs tab.

Step 14

Click the WLAN of the SSID for the Captive Portal rule.

Step 15

Choose Security.

Step 16

In the Layer 2 tab, select the MAC Filtering check box.

Step 17

In the Layer 3 tab, ensure that the following is configured.

In the Layer 3 security drop-down list, Web Policy is selected, and the On Mac Filter Failure radio button is selected.

Note

These configurations in the Layer 3 are done when creating the SSIDs.

Step 18

In the AAA Servers tab, in the Radius Servers area, do the following:

Select the Enabled check box for the Authentication Servers.

From the Server 1 drop-down list, choose the radius server you have previously defined.

Step 19

In the Authentication priority order for the web-auth user area, in the Order Used for Authentication box, set Radius as first in the order.

Note

Use the Up and Down buttons to rearrange the order.

Step 20

Click the Advanced tab, and select the Enabled check box for Allow AAA Override.

Step 21

Click Apply.

Step 22

In the Cisco Wireless Controller main window, click the Security tab.

Step 23

Choose AAA > MAC Filtering.

Step 24

In the MAC Filtering window that appears, do the following:

From the RADIUS Compatibility Mode drop-down list, choose Cisco ACS.
From the MAC Delimiter drop-down list, choose Hyphen.
Click Apply.

Step 25

Ensure that the wall gardens are configured for the ACLs. To view the wall garden ranges, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a CUWN SSID in the SSIDs window.The Configure Manually link appears only after adding a Cisco AireOS SSID.

Configuring Cisco Wireless Controller for Social Authentication

For social authentication with Cisco Unified Wireless Network, you must do some configurations in the Cisco Wireless Controller.

To configure the Cisco Unified Wireless Network for social authentication, perform the following steps:

Procedure

Step 1

Step 2

Choose Security > Access Control Lists > Access Control Lists.

Step 3

In the Access Control List window that appears, click the Access Control List configured for Cisco DNA Spaces.

Click Add New Rule and add additional two rules with following information. .


No	Action	Source IP Address/Netmask	Destination IP Address/Netmask	Protocol	Source Port Range	Destination Port Range	DSCP	Direction
1	Permit	0.0.0.0/0.0.0.0	0.0.0.0/0.0.0.0	TCP	HTTPS	Any	Any	Any
2	Permit	0.0.0.0/0.0.0.0	0.0.0.0/0.0.0.0	TCP	Any	HTTPS	Any	Any

Note

This wall garden ranges configured for social authentication will allow the customers to access all the HTTPS web sites directly after connecting to your SSID, without using the captive portal.

Step 4

Add social platform specific domains as ACLs based on the social networks that you want to use for authentication. To add social domains as ACLs, perform the following steps:

In the Cisco Wireless Controller dashboard, choose Security > Access Control Lists.
Click More Actions for the Access Control List configured for Cisco DNA Spaces..
Click Add Remove URL.
Enter a social URL name, and click Add.

Repeat steps c and d for each domain.

Note

These domain names are managed by the social networks and can change at any time. Also, these domain names are subjected to change based on country/region. If you are facing any issue, contact the Cisco DNA Spaces support team.

The commonly used domain names for various social platforms are as follows:

Table 2.
Social Domains
Facebook
facebook.com
static.xx.fbcdn.net
www.gstatic.com
m.facebook.com
fbcdn.net
fbsbx.com
LinkedIn
www.linkedin.com
static-exp1.licdn.com
Twitter
abs.twimg.com
syndication.twitter.com
twitter.com
analytics.twitter.com
Instagram
instagram.com
*.instagram.com
api.instagram.com
d36xtkk24g8jdx.cloudfront.net
www.facebook.com
connect.facebook.net
*.akamaihd.net

Connecting Cisco Catalyst 9800 Series Wireless Controller or Cisco Wireless Controller to Cisco DNA Spaces Using WLC Direct Connect or Cisco DNA Spaces Connector

To import the locations from Cisco 9800 Series Wireless Controller or Cisco Wireless Controller (without CMX) to Cisco DNA Spaces, you must first connect the Controller to Cisco DNA Spaces through one of the connectors.

The connectors, Cisco WLC Direct Connect and Cisco DNA Spaces Connector can be used for both Cisco Wireless Controller and Cisco Catalyst 9800 Series Wireless Controller.

Note

If you want to connect a Cisco Wireless Controller with both Cisco CMX and Cisco DNA Spaces simultaneously, you must use a Cisco DNA Spaces Connector. However, it is not recommended to connect a single Controller to both Cisco DNA Spaces and Cisco CMX simultaneously.
It is recommended not to compare the data displayed in Cisco DNA Spaces reports such as Behavior Metrics with the data displayed in Cisco Wireless Controller or Cisco CMX, as it is expected to differ as per design.
For importing a Controller to Cisco DNA Spaces, ensure that atleast one AP is connected to that particular Controller.
In the Controller, if new APs are added to the Controller, those APs get automatically imported during the next Controller synchronization. If an imported AP is deleted from the Controller, the changes will be reflected in Cisco DNA Spaces only after 48 hours. However, an AP without updates will be deleted after 48 hours only if updates are coming from other APs. For example, if there are 10 APs that are configured, and if 2 APs are removed from Controller, these 2 APs will be removed from Cisco DNA Spaces only when updates are received from other 8 APs.
If an AP is disassociated from the Controller, it is not immediately removed from Cisco DNA Spaces to release the AP count. The APs will be removed from Cisco DNA Spaces only after 48 hours.

The configurations required for various combinations of Wireless Controllers and Connectors are as follows:

Connecting Cisco DNA Spaces to Cisco Wireless Controller Using Cisco WLC Direct Connect

To connect the Cisco Wireless Controller Version 8.3 or later (without Cisco CMX installation) to the Cisco DNA Spaces, and to import the Cisco Wireless Controller and its access points to the Cisco DNA Spaces, perform the following steps:

Before you begin

You need Cisco Wireless Controller Version 8.3 or later.
For importing a Cisco Wireless Controller to Cisco DNA Spaces, ensure that atleast one AP is connected to that particular Cisco Wireless Controller.
The Cisco Wireless Controller must be able to reach Cisco DNA Spaces cloud over HTTPS.
Cisco Wireless Controller must be able to reach out to the internet.
To use Cisco DNA Spaces with anchor mode, you must have a network deployment with Cisco Wireless Controllers in both anchor controller mode and foreign controller mode. If the network deployment contains Cisco Wireless Controller in Anchor Controller mode and Foreign Controller mode, Cisco WLC Direct Connect must be enabled in both controllers using the commands described in this section. In addition, the Cisco Wireless Controllers in both modes must be able to reach the Cisco DNA Spaces cloud over HTTPS. However, Cisco DNA Spaces does not support Cisco Wireless Controller Version 8.3.102 in anchor mode.
To connect the Cisco AireOS Wireless Controller Version 8.3 or later successfully to the Cisco DNA Spaces using Cisco WLC Direct Connect, you must have a root certificate issued by DigiCert CA. If the network deployment contains Cisco Wireless Controller in Anchor Controller mode and Foreign Controller mode, you must import the certificate to the Cisco Wireless Controllers in both modes”.

Procedure

Step 1

Import the DigiCert CA root certificate.

Download your root certificate from the following link:

'
https://global-root-ca.chain-demos.digicert.com/info/index.html
Copy the root certificate content to a file with .cer extension, and save the file as {your_filename}.cer.
Copy the {your_filename}.cer file to the default directory on your TFTP.

 transfer download datatype cmx-serv-ca-cert 
 transfer download mode tftp 
 transfer download filename {your_filename}.cer 
 transfer download serverip {your_tftp_server_ip} 
 transfer download start

Type Y to start the upload

After the new root certificate has been uploaded successfully, execute the following commands to disable, and then enable your Cisco CMX Cloud Services:

config cloud-services cmx disable 
config cloud-services cmx enable

Note

After uploading the root certificate, Cisco Wireless Controller will prompt for reboot. Rebooting is recommended, but not mandatory. The certificate will be installed in either case.

If you try to connect the Wireless Controller to Cisco DNA Spaces using a root certificate not issued by DigiCert CA, you will get the following error:

https:SSL certificate problem: unable to get local issuer certificate

Step 2

In the Cisco Wireless Controller CLI mode, execute the following commands:

config cloud-services cmx disable 
 config cloud-services server url https://{Customer Path Key}.{LB Domain} {LB IP Address}
config cloud-services server id-token <Customer JWT Token> 
 config network dns serverip <dns server ip> 
 config cloud-services cmx enable

Note

To view the {Customer Path Key}, {LB Domain}, {LB IP Address}, and {Customer JWT Token}, log in to Cisco DNA Spaces dashboard, and click the three-line menu icon that is displayed at the top-left of the dashboard. Choose Setup > Wireless Networks. Then expand Connect WLC / Catalyst 9800 Directly, and click View Token. Click the WLC tab, and you can view the {Customer Path Key}, {LB Domain}, and {LB IP Address} at Step 1b and {Customer JWT Token} at Step 1c.

Step 3

Check the summary using the following command:

show cloud-services cmx summary

The result appears.

Now in the Cisco DNA Spaces dashboard, when you choose CUWN-WLC in the Add a Wireless Network window, the WLC will be listed. So, you can import the APs of that WLC to the Cisco DNA Spaces.

Example:

Sample Result

(Cisco Controller) >show cloud-services cmx summary

CMX Service

Server ....................................... https://$customerpathkey.dnaspaces.io

IP Address.................................... <Local System IP Address>

Connectivity.................................. https: UP

Service Status ............................... Active

Last Request Status........................... HTTP/1.1 200 OK

Heartbeat Status ............................. OK

Now the Cisco Wireless Controller will be available for import in the Cisco DNA Spaces location hierarchy. You can import the locations using Map services or Access Point Prefix.

To import the locations based on Access Point prefix, see Importing the Locations using Access Point Prefix
To import the locations using Map Services, see Importing Locations to the Location Hierarchy Using Map Services

What to do next

For social authentication, radius authentication, and internet provisioning, refer to the following sections:

Configuring Cisco AireOS for Social Authentication
Configuring Cisco AireOS for Internet Provisioning and Radius Authentication

Configuring Cisco Wireless Controller (without Cisco CMX) for Notification and Reports

Without Cisco CMX, you can connect Cisco Wireless Controller to Cisco DNA Spaces using the connectorsWLC Direct Connect and Cisco DNA Spaces Connector. In these cases, the configurations required for notifications and reports will be done automatically when you import the Cisco Wireless Controller.

Note

If you are using Cisco DNA Spaces with WLC Direct Connect or Cisco DNA Spaces Connector, the Controller must be in “Foreign controller” mode.

Connecting Cisco DNA Spaces to Cisco Catalyst 9800 Series Wireless Controller Using Cisco WLC Direct Connect

Before you begin

For importing a Cisco Catalyst 9800 Series Wireless Controller to Cisco DNA Spaces, ensure that atleast one AP is connected to that particular Cisco Catalyst 9800 Series Wireless Controller.
Cisco Catalyst 9800 Series Wireless Controller must be able to reach Cisco DNA Spaces cloud over HTTPS.
Cisco Catalyst 9800 Series Wireless Controller must be able to reach out to the internet.
To connect the Cisco Catalyst 9800 Series Wireless Controller successfully to the Cisco DNA Spaces using Cisco WLC Direct Connect, you must have a root certificate trusted by Cisco.

To connect the Cisco Catalyst 9800 Series Controller to Cisco DNA Spaces, and to import that controller and its access points to the Cisco DNA Spaces, perform the following steps:

Procedure

Step 1

Import the Cisco External Trusted Root Store to install the DigiCert Global Root CA on the Controller.

Download the root certificate using the following command:

(config)#crypto pki trustpool import url http://www.cisco.com/security/pki/trs/ios.p7b

verify the certificate installation using the following command:

#show crypto pki trustpool | section DigiCert Global Root CA
cn=DigiCert Global Root CA
cn=DigiCert Global Root CA

Note

You must check the output to verify correct trustpool installation.

Step 2

On Cisco Catalyst 9800 Series Controller, enable DNS to resolve the Cisco DNA Spaces URL using the following commands:


a. (config)#ip name-server <Primary IP> <Secondary IP> 
b. (config)#ip domain lookup
c. (config)#ip route 0.0.0.0 0.0.0.0 <default_gw_ip_addr>

Step 3

Enable nmsp cloud-services on Cisco Catalyst 9800 Series Controller to communicate with Cisco DNA Spaces Cloud over HTTPS.


a. (config)#nmsp cloud-services server url <URL>
b. (config)#nmsp cloud-services server token <Customer JWT TOKEN>
c. (config)#nmsp cloud-services http-proxy <proxy ip_addr> <proxy port> -This command is optional, and must be used only if the proxy server needs to reach the internet.
d. (config)#nmsp cloud-services enable

Note

To view the server URL and token, log in to Cisco DNA Spaces dashboard, and click the three-line menu icon that is displayed at the top-left of the dashboard. Choose Setup > Wireless Networks. Then expand Connect WLC / Catalyst 9800 Directly, and click View Token. Click the Cisco Catalyst 9800 tab, and you can see the URL at Step 2b and token at Step 2c.

Step 4

Confirm the connection between Cisco Catalyst 9800 Series Controller and Cisco DNA Spaces Cloud by executing the following command:

#show nmsp cloud-services summary

The result must be as follows.

Example:

Sample Result

Server : https://abc.dnaspaces.io

CMX Service : Enabled

Connectivity : https: UP

Service Status : Active

Last IP Address : <Local System IP Address>

Last Request Status : HTTP/1.1 200 OK

Heartbeat Status : OK

Now the Cisco Catalyst 9800 Series Wireless Controller will be available for import in the Cisco DNA Spaces location hierarchy.

Step 5

To view the breif summary of active/inactive Cisco CMX cloud connections, execute the following command:

#show nmsp status

Note

You can see the state of the connection to Cisco DNA Spaces Cloud connection.

Step 6

To view aggregated subscriptions summary for all active Cisco DNA Spaces cloud connections, execute the following command:

# show nmsp subscription summary

Note

You can view the services that Cisco DNA Spaces Cloud is subscribed to, after the connection is established.

Step 7

Import the locations to the Cisco DNA Spaces dashboard. For more information on importing the location, see Defining the Location Hierarchy for Cisco Catalyst 9800 Series Wireless Controllers or Cisco Wireless Controller (without Cisco CMX).

Step 8

If you want to use the Captive Portals and Engagements apps, do the required configuration from the following:

Configuring Cisco Catalyst 9800 Series Wireless Controller (Local Mode) for Captive Portals and Engagements Apps Using CLI

Note

The minimum supported Cisco Catalyst 9800 Series Wireless Controller Version is 16.10.20181030.

To configure Cisco Catalyst 9800 Series Wireless Controller for Captive Portals and Engagements app , perform the following steps:

Procedure

Step 1

In the Cisco DNA Spaces dashboard, configure a Cisco Catalyst SSID. For more information on configuring the SSIDs, see the “Importing the SSIDs for Cisco Unified Wireless Network” section.

Note

You can define any name for the SSID. You must use the same SSID name when configuring the Cisco Catalyst 9800 Series Wireless Controller .

Step 2

On Cisco Catalyst 9800 Series Wireless Controller , enable HTTP and HTTPS as follows:

ip http server

ip http secure-server

Step 3

Configure parameter maps for client redirection.

parameter-map type webauth <map name>

type consent

timeout init-state sec 600

redirect for-login <splash page URL>

redirect append ap-mac tag ap_mac

redirect append wlan-ssid tag wlan

redirect append client-mac tag client_mac

redirect portal ipv4 <IP Address>

logout-window-disabled

success-window-disable

Note

For Splash URL and IP address, in the Cisco DNA Spaces dashboard, click the Captive Portal app. Click SSIDs, and then click the Configure Manually link for the Cisco Catalyst SSID created in Step 1. The splash URL for your CUWN account will be listed in the Creating the SSIDs in CUWN-WLC section. The IP address will be listed in the Creating the Access Control List section. You must use only any one IP address from the list. You can also contact the Cisco DNA Spaces support team.

Step 4

Configure virtual IP address for client redirection.

parameter-map type webauth global

virtual-ip ipv4 192.0.2.0

intercept-https-enable

Note

Instead of ipV4 192.0.2.0 , you can configure any virtual IP. The virtual-ip should be a non-routable and a not used IP address.
You must have a valid SSL certificate for the virtual IP/Domain installed in Cisco Catalyst 9800 Series Wireless Controller controller.

Step 5

Configure FQDN URL filtering.

For central switch wlans, the URL filter list is attached to the policy-profile:

urlfilter list social_login_fqdn_central

action permit

url <splash page domain>

Note

Configure the domain configured at Step 3 for "redirect for-login".

url *.fbcdn.net

url *.licdn.com

url *.licdn.net

url *.twimg.com

url *.gstatic.com

url *.twitter.com

url *.akamaihd.net

url *.facebook.com

url *.facebook.net

url *.linkedin.com

url ssl.gstatic.com

url *.googleapis.com

url static.licdn.com

url *.accounts.google.com

url *.connect.facebook.net

url oauth.googleusercontent.com

wireless profile policy default-policy-profile

urlfilter list pre-auth-filter social_login_fqdn_central

For flex WLANs the URL filter list is attached to the flex-profile

urlfilter list social_login_fqdn_flex

action permit

url <splash page domain>

Note

Configure the domain configured at Step 3 for "redirect for-login".

url *.fbcdn.net

url *.licdn.com

url *.licdn.net

url *.twimg.com

url *.gstatic.com

url *.twitter.com

url *.akamaihd.net

url *.facebook.com

url *.facebook.net

url *.linkedin.com

url ssl.gstatic.com

url *.googleapis.com

url static.licdn.com

url *.accounts.google.com

url *.connect.facebook.net

url oauth.googleusercontent.com

urlfilter list social_login_fqdn_central

wireless profile flex default-flex-profile

acl-policy <WA-sec-<ip>>

urlfilter list social_login_fqdn_flex

description "default flex profile"

Step 6

Configure Radius Accounting.

aaa new-model

aaa group server radius <group name>

server name <radius server name>

subscriber mac-filtering security-mode mac

mac-delimiter hyphen

aaa accounting login <authentication> group <group name>

aaa authorization network <Authorization> group <Group Name>

aaa accounting identity <Accounting> start-stop group <Group Name>

aaa server radius dynamic-author

client <Radius Server IP> server-key <Radius Secret>

aaa session-id common

radius-server attribute wireless accounting call-station-id ap-macaddress-ssid

radius server <Radius Name>

address ipv4 <Radius Server IP> auth-port 1812 acct-port 1813

key <Radius Secret>

Note

You can configure only the Cisco DNA Spaces radius servers. To view the ipV4 IP address, secret key, and port for radius server configuration, in the Cisco DNA Spaces dashboard, click the Captive Portal app. Click SSIDs, and then click the Configure Manually link for the Cisco Catalyst SSID created in Step 1. The radius server details will be listed in the Radius Server Configuration section. Configure both the primary and secondary radius server IPs. You can also contact the Cisco DNA Spaces support team.

Step 7

Configure Policy Profile.

wireless profile policy default-policy-profile

aaa-override

accounting-list <Accounting Server>

autoqos mode voice

description "default policy profile"

service-policy input platinum-up

service-policy output platinum

urlfilter list pre-auth-filter <url filter>

vlan <id>

no shutdown

Step 8

Configure WLAN.

wlan <WLAN name >

ip access-group web <ACL Name>

no security wpa

no security wpa akm dot1x

no security wpa wpa2 ciphers aes

security web-auth

security web-auth authentication-list default

security web-auth parameter-map <map name>

no shutdown

Note

Ensure that the WLAN name you mention here matches with the SSID name you configured in Cisco DNA Spaces at step 1.

Step 9

Enable DNS resolution and make sure you have a default gateway configured on the Cisco Catalyst 9800 Series Wireless Controller .

ip name-server <dns_ip_address>

ip domain-lookup

ip route 0.0.0.0 0.0.0.0 <default_gw_ip_addr>

You can then import the SSIDs to Cisco DNA Spaces, and configure captive portals for SSIDs using the Captive Portal Rule.

Configuring Cisco Catalyst 9800 Series Wireless Controller GUI (Local Mode) for Captive Portals and Engagements Apps

Note

The minimum supported Cisco Catalyst 9800 Series Wireless Controller Versions are 16.10.1E and 16.10.11.

To configure Cisco Catalyst 9800 Series Wireless Controller for Captive Portals and Engagements apps, perform the following steps:

Procedure

Step 1

In the Cisco DNA Spaces dashboard, configure a Cisco Catalyst SSID. For more information on configuring the SSIDs, see the Importing the SSIDs for Cisco Unified Wireless Network section.

Step 2

Create the Parameter Map:

Log into Cisco Catalyst 9800 Series Wireless Controller .
Choose Configuration > Security > Web Auth.
On the Web Auth Parameter Map tab, click Add.
In the Parameter-map name field, enter parameter-map name.
From the Type drop-down list, choose consent, and click Apply to Device.

The newly created Parameter Map gets listed on the Web Auth Parameter Map tab.
Click the newly created Parameter Map.
On the General tab, check the Disable Success Window check box, and the Disable Logout Window check box.

On the Advanced tab, do the following:

In the Redirect for log-in field, enter the splash page URL https://<domain>/p2/<customerPathKey>.
In the Redirect Append for AP MAC Address field, enter ap_mac.
In the Redirect Append for Client MAC Address field, enter client_mac.
In the Redirect Append for WLAN SSID field, enter wlan.
In the Portal IPV4 Address field, enter the Cisco DNA Spaces IP to be allowed.

Note

To view the IP address to be allowed, in the Cisco DNA Spaces dashboard, click the Captive Portals app. Click SSIDs, and then click the Configure Manually link for the Cisco Catalyst SSID. The IP addresses will be listed in the Creating the Access Control List section. You must use only any one IP address from the list. The remaining IPs are specified when creating the ACL. The Configure Manually link appears only after adding a Cisco Catalyst SSID.

Click Update and Apply.

Step 3

Install the web-auth certificate and configure the global parameter map.

You must have a valid SSL certificate for the virtual IP/Domain installed in Cisco Catalyst 9800 Series Wireless Controller. You can purchase any wild card certificate.

Log into Cisco Catalyst 9800 Series Wireless Controller.
In the Cisco Catalyst 9800 Series Wireless Controller dashboard, choose Configuration > Security > Web Auth.
Click the Parameter map name, global.
Configure Maximum Http connections as 100
Configure Init-State Timeout(Secs) as 120
On the General tab, from the Type drop-down list, choose Webauth.
Specify virtual IPv4 address (virtual IP) or virtual IPv4 Host name (domain) in the respective field.
Configure Watch List Expiry Timeout(Secs) as 600.
Check the Web Auth intercept HTTPS check box.
Click Update & Apply.
Convert the certificate into pkcs12.

The file format will be .p12.
Copy the file into the tftp server.
Download the certificate copied to the tftp server using the following steps:
- In the Cisco Catalyst 9800 Series Wireless Controller CLI, enter the following command:
```
crypto pki import <name> pkcs12 tftp://<tftp server ip>:/ password <certificate password>
```
- To confirm the tftp server IP, enter yes.
- Enter the certificate file name. For example, wildcard.wifi-mx.com.p12.
  
  The certificate gets downloaded.
To verify the installed certificate, in the Cisco Catalyst 9800 Series Wireless Controller dashboard, choose Configuration > Web Auth > Certificate.

The downloaded certificate appears as the last certificate in the list.
To map the installed certificate with webauth parameter map, in the Cisco Catalyst 9800 Series Wireless Controller CLI, execute the following commands:
- Conf t
- parameter-map type webauth global
- trustpoint <installed trustpool name > ex: trustpool name
- end
- wr (to save the configuration)
Reload Cisco Catalyst 9800 Series Wireless Controller .

Step 4

Create the ACL by adding URL filters.

Choose Configuration > Security > URL Filter.
In the URL Filters window, click Add.
In the List Name field, enter the list name.
Change the status of Action to Permit
In the URLs field, enter the splash page domain configured at Step 2h (Parameter Map).
Add the following domains, if you want to enable social authentication:
- *.fbcdn.net
- *.licdn.com
- *.licdn.net
- *.twimg.com
- *.gstatic.com
- *.twitter.com
- *.akamaihd.net
- *.facebook.com
- *.facebook.net
- *.linkedin.com
- ssl.gstatic.com
- *.googleapis.com
- static.licdn.com
- *.accounts.google.com
- *.connect.facebook.net
- oauth.googleusercontent.com
Choose Configuration > Tags and Profiles > Policy.
In the Policy Profile window, click default-policy-profile.
In the Edit Policy Profile window, click the Access Policies tab.
In the URL Filters area, from the Pre Auth drop-down list, choose the previously created ACL.
Click Update & Apply to Device .

Step 5

Create the SSID.

Choose Configuration > Tags and Profiles > WLANs.
Click Add.

On the General tab, in the Profile Name field, enter the profile name.
In the SSID field, enter the SSID name defined at Step 1.
Set the status as Enabled.
Click the Security tab, and then click the Layer2 tab.
From the Layer 2 Security Mode drop-down list, choose None.
Click the Layer3 tab.
Check the Web Policy check box.
From the WebAuth Parameter Map drop-down list, choose the Web Auth Parameter Map created at step 2.
Click Save & Apply to Device.

Step 6

Configure the RADIUS server.

Note

We highly recommend to use RADIUS authentication for captive portals. The following features work only if you configure RADIUS authentication.

Seamless Internet Provisioning.
Extended session duration.
Deny Internet.

Choose Configuration > Security > AAA.
In the Authentication Authorization and Accounting window, click the Servers/Groups tab.
Choose Radius > Servers, and click Add.
In the Name field, enter a name for the radius server.

In the IPv4 / IPv6 Server Address field, enter the radius server address.

Note

You can configure only the Cisco DNA Spaces radius servers. To view the radius server IP address and secret key, in the Cisco DNA Spaces dashboard, click the Captive Portal app. Click SSIDs, and then click the Configure Manually link for the Cisco Catalyst SSID created at Step 1.In the window that appears, the radius server details will be listed in the Radius Server Configuration section. Configure both the primary and secondary radius server IPs.You can also contact the Cisco DNA Spaces support team.

In the Key field, enter the key, and confirm it in the Confirm Key field.
In the Auth Port field, enter 1812.
In the Acct Port field, enter 1813.
Click Save & Apply to Device.

The server added will be available in Servers list.
Choose Radius > Server Groups, and click Add.
In the Name field, enter a name.
From the MAC-Delimiter drop-down list, choose hyphen.
From the MAC-Filtering drop-down list, choose mac.
Move the radius server previously created from “Available Servers” to “Assigned Servers” using the arrow button.
Click Save & Apply to Device.
In the Authentication Authorization and Accounting window, click the AAA Method List tab.
Click Authentication, and click Add and specify the following details:
1. In the Method List Name field, enter the method list name.
2. From the Type drop-down list, choose Login
3. From the Group Type drop-down list, choose Group.
4. Move the server group created earlier (step j to Step o) from Available Server Groups to Assigned Servers Groups, and click Save & Apply to Device.
On the AAA Method List tab, click Authorization, and click Add, and specify the following details:
1. In the Method List Name field, enter the method list name.
2. From the Type drop-down list, choose Network.
3. From the Group Type drop-down list, choose group.
4. Move the server group previously created (step j to Step o) from Available Servers to Assigned Servers using the arrow button, and click Save & Apply to Device.
On the AAA Method List tab, click Accounting, and click Add, and specify the following details:
1. In the Method List Name field, enter the method list name.
2. From the Type drop-down list, choose Identity.
3. From the Group Type drop-down list, choose group.
4. Move the server group previously created (step j to Step o) from Available Servers to Assigned Servers using the arrow button, and click Save & Apply to Device.

Step 7

Enable L3 and L2 authentication (Mac Filtering).

Make sure Type is selected as webauth in parameter-map for RADIUS Authentication.

Note

To configure L3 and L2 authentication, ensure that you have created the SSIDs and have done all the configurations at step 5. You can then import the SSIDs to Cisco DNA Spaces, and configure captive portals for SSIDs using the Captive Portal Rule.

Choose Configuration > Tags and Profiles > WLANs.
Click the SSID for which you want to configure L2 and L3 Authentication.
In the Edit WLAN window, click the Security tab.
On the Layer3 tab, from the Authentication drop-down list, choose the radius authentication configured previously(step 6q).
On the Layer2 tab, to enable Mac Filtering, check the MAC Filtering check box.
From the Authorization List drop-down list that appears, choose the authorization server created previously(step 6r).
Click Show Advanced Settings.
Check the On Mac Filter Failure check box.
Click Update & Apply to Device.
Choose Configuration > Tags and Profiles > Policy.
Click default-policy-profile.
On the Advanced tab, in the AAA Policy area, check the Allow AAA Override check box.
Ensure that default aaa policy is selected from the Policy Name drop-down list.
Click Update & Apply to Device.

Step 8

Enable Radius Accounting.

Choose Configuration > Tags and Profiles > Policy.
Click default-policy-profile.
On the Advanced tab, from the Account List drop-down list, choose the accounting server created at Step 6s.
Click Update & Apply to Device.

Configuring Cisco Catalyst 9800 Series Wireless Controller GUI (Flex Mode or Mobility Express) for Captive Portals and Engagements Apps

Note

The minimum supported Cisco Catalyst 9800 Series Wireless Controller Versions are 16.10.1E and 16.10.11.

To configure "Cisco Catalyst 9800 Series Wireless Controller in Flex mode" or "Cisco Catalyst 9800 Series Wireless Controller with Mobility Express" for Captive Portals and Engagements apps, perform the following steps:

Procedure

Step 1

To configure the Cisco Catalyst 9800 Series Wireless Controller in Flex mode, ensure that the following configurations are done:

This configuration is not required for Mobility Express.

Log into Cisco Catalyst 9800 Series Wireless Controller .
Choose Configuration > Tags > Site.
Select the required site name.
Uncheck the Enable Local Site check box.
Click Update & Apply to Device.
Choose Configuration > Policy.
Select the required policy name.
Disable Central Switching.
Click Update & Apply to Device..

Note

AP might reboot and rejoin the wireless controller on changing from Local Mode to Flex mode.

Step 2

In the Cisco DNA Spaces dashboard, configure a Cisco Catalyst SSID. For more information on configuring the SSIDs, see the Importing the SSIDs for Cisco Unified Wireless Network section.

Step 3

Create the Parameter Map:

Log into Cisco Catalyst 9800 Series Wireless Controller .
Choose Configuration > Security > Web Auth.
On the Web Auth Parameter Map tab, click Add.
In the Parameter-map name field, enter parameter-map name.
From the Type drop-down list, choose consent, and click Apply to Device.

The newly created Parameter Map gets listed on the Web Auth Parameter Map tab.
Click the newly created Parameter Map.
On the General tab, check the Disable Success Window check box, and the Disable Logout Window check box.

On the Advanced tab, do the following:

In the Redirect for log-in field, enter the splash page URL https://<domain>/p2/<customerPathKey>.
In the Redirect Append for AP MAC Address field, enter ap_mac.
In the Redirect Append for Client MAC Address field, enter client_mac.
In the Redirect Append for WLAN SSID field, enter wlan.
In the Portal IPV4 Address field, enter the Cisco DNA Spaces IP to be allowed.

Note

To view the IP address to be allowed, in the Cisco DNA Spaces dashboard, click the Captive Portals app. Click SSIDs, and then click the Configure Manually link for the CUWN/Catalyst SSID. The IP addresses will be listed in the Creating the Access Control List section. You must use only any one IP address from the list. The remaining IPs are specified when creating the ACL. The Configure Manually link appears only after adding a Cisco Catalyst SSID.

Click Update and Apply.

Step 4

Install the web-auth certificate and configure the global parameter map.

You must have a valid SSL certificate for the virtual IP/Domain installed in Cisco Catalyst 9800 Series Wireless Controller. You can purchase any wild card certificate.

Log into Cisco Catalyst 9800 Series Wireless Controller.
In the Cisco Catalyst 9800 Series Wireless Controller dashboard, choose Configuration > Security > Web Auth.
Click the Parameter map name, global.
Configure Maximum Http connections as 100
Configure Init-State Timeout(Secs) as 120
On the General tab, from the Type drop-down list, choose Webauth.
Specify virtual IPv4 address (virtual IP) or virtual IPv4 Host name (domain) in the respective field.
Configure Watch List Expiry Timeout(Secs) as 600.
Check the Web Auth intercept HTTPS check box.
Click Update & Apply.
Convert the certificate into pkcs12.

The file format will be .p12.
Copy the file into the tftp server.
Download the certificate from the tftp server using the following steps:
- In the Cisco Catalyst 9800 Series Wireless Controller CLI, enter the following command:
```
crypto pki import <name> pkcs12 tftp://<tftp server ip>:/ password <certificate password>
```
- To confirm the tftp server IP, enter yes.
- Enter the certificate file name. For example, wildcard.wifi-mx.com.p12.
  
  The certificate gets downloaded.
To verify the installed certificate, in the Cisco Catalyst 9800 Series Wireless Controller dashboard, choose Configuration > Web Auth > Certificate.

The downloaded certificate appears as the last certificate in the list.
To map the installed certificate with webauth parameter map, in the Cisco Catalyst 9800 Series Wireless Controller CLI, execute the following commands:
- Conf t
- parameter-map type webauth global
- trustpoint <installed trustpool name > ex: trustpool name
- end
- wr (to save the configuration)
Reload Cisco Catalyst 9800 Series Wireless Controller .

Step 5

Create the ACL by adding URL filters.

Choose Configuration > Security > URL Filter.
In the URL Filters window, click Add.
In the List Name field, enter the list name.
Change the status of Action to Permit
In the URLs field, enter the splash page domain configured at Step 3h (Parameter Map).
Add the following domains, if you want to enable social authentication:
- *.fbcdn.net
- *.licdn.com
- *.licdn.net
- *.twimg.com
- *.gstatic.com
- *.twitter.com
- *.akamaihd.net
- *.facebook.com
- *.facebook.net
- *.linkedin.com
- ssl.gstatic.com
- *.googleapis.com
- static.licdn.com
- *.accounts.google.com
- *.connect.facebook.net
- oauth.googleusercontent.com
Choose Configuration > Tags and Profiles > Policy.
In the Policy Profile window, click default-policy-profile.
In the Edit Policy Profile window, click the Access Policies tab.
In the URL Filters area, from the Pre Auth drop-down list, choose the previously created ACL.
Click Update & Apply to Device .
Choose Configuration > Tags and Profiles > Flex.
Click the Profile in use.
In the Edit Flex Profile window that appears, click Policy ACL tab.
Click Add.
From the ACL Name drop-down list, choose WA-sec-<ip>.
From the Pre Auth URL Filter drop-down list, choose URL filter ACL created previously( Step 5a to 5e).
Click Save.
Click Update & Apply to Device.

Step 6

Create the SSID.

Choose Configuration > Tags and Profiles > WLANs.
Click Add.

On the General tab, in the Profile Name field, enter the profile name.
In the SSID field, enter the SSID name defined at Step 2.
Set the status as Enabled.
Click the Security tab, and then click the Layer2 tab.
From the Layer 2 Security Mode drop-down list, choose None.
Click the Layer3 tab.
Check the Web Policy check box.
From the WebAuth Parameter Map drop-down list, choose the Web Auth Parameter Map created at step 3.
Click Save & Apply to Device.

Step 7

Configure the RADIUS server.

Note

We highly recommend to use RADIUS authentication for captive portals. The following features work only if you configure RADIUS authentication.

Seamless Internet Provisioning.
Extended session duration.
Deny Internet.

Choose Configuration > Security > AAA.
In the Authentication Authorization and Accounting window, click the Servers/Groups tab.
Choose Radius > Servers, and click Add.
In the Name field, enter a name for the radius server.

In the IPv4 / IPv6 Server Address field, enter the radius server address.

Note

You can configure only the Cisco DNA Spaces radius servers. To view the radius server IP address and secret key, in the Cisco DNA Spaces dashboard, click the Captive Portal app. Click SSIDs, and then click the Configure Manually link for the Cisco Catalyst SSID created at Step 2. In the window that appears, the radius server details will be listed in the Radius Server Configuration section. Configure both the primary and secondary radius server IPs.You can also contact the Cisco DNA Spaces support team.

In the Key field, enter the key, and confirm it in the Confirm Key field.
In the Auth Port field, enter 1812.
In the Acct Port field, enter 1813.
Click Save & Apply to Device.

The server added will be available in Servers list.
Choose Radius > Server Groups, and click Add.
In the Name field, enter a name.
From the MAC-Delimiter drop-down list, choose hyphen.
From the MAC-Filtering drop-down list, choose mac.
Move the radius server previously created from “Available Servers” to “Assigned Servers” using the arrow button.
Click Save & Apply to Device.
In the Authentication Authorization and Accounting window, click the AAA Method List tab.
Click Authentication, and click Add and specify the following details:
1. In the Method List Name field, enter the method list name.
2. From the Type drop-down list, choose Login
3. From the Group Type drop-down list, choose Group.
4. Move the server group created earlier (step j to Step o) from Available Server Groups to Assigned Servers Groups, and click Save & Apply to Device.
On the AAA Method List tab, click Authorization, and click Add, and specify the following details:
1. In the Method List Name field, enter the method list name.
2. From the Type drop-down list, choose Network.
3. From the Group Type drop-down list, choose group.
4. Move the server group previously created (step j to Step o) from Available Servers to Assigned Servers using the arrow button, and click Save & Apply to Device.
On the AAA Method List tab, click Accounting, and click Add, and specify the following details:
1. In the Method List Name field, enter the method list name.
2. From the Type drop-down list, choose Identity.
3. From the Group Type drop-down list, choose group.
4. Move the server group previously created (step j to Step o) from Available Servers to Assigned Servers using the arrow button, and click Save & Apply to Device.

Step 8

Enable L3 and L2 authentication (Mac Filtering).

Make sure Type is selected as webauth in parameter-map for RADIUS Authentication.

Note

To configure L3 and L2 authentication, ensure that you have created the SSIDs and have done all the configurations at step 6. You can then import the SSIDs to Cisco DNA Spaces, and configure captive portals for SSIDs using the Captive Portal Rule.

Choose Configuration > Tags and Profiles > WLANs.
Click the SSID for which you want to configure L2 and L3 Authentication.
In the Edit WLAN window, click the Security tab.
On the Layer3 tab, from the Authentication drop-down list, choose the radius authentication configured previously(step 7q).
On the Layer2 tab, to enable Mac Filtering, check the MAC Filtering check box.
From the Authorization List drop-down list that appears, choose the authorization server created previously(step 7r).
Click Show Advanced Settings.
Check the On Mac Filter Failure check box.
Click Update & Apply to Device.
Choose Configuration > Tags and Profiles > Policy.
Click default-policy-profile.
On the Advanced tab, in the AAA Policy area, check the Allow AAA Override check box.
Ensure that default aaa policy is selected from the Policy Name drop-down list.
Click Update & Apply to Device.

Step 9

Enable Radius Accounting.

Choose Configuration > Tags and Profiles > Policy.
Click default-policy-profile.
On the Advanced tab, from the Account List drop-down list, choose the accounting server created at Step 7s.
Click Update & Apply to Device.

Connecting Cisco DNA Spaces to Cisco AireOS Wireless Controller or Cisco Catalyst 9800 Series Wireless Controller using Cisco DNA Spaces Connector

Cisco Wireless Controller with Cisco DNA Spaces Connector

To connect Cisco AireOS Wireless Controller to Cisco DNA Spaces using a Cisco DNA Spaces Connector, and to configure captive portal authentication or notifications, do the following:

Connect Cisco AireOS Wireless Controller to Cisco DNA Spaces using a Cisco DNA Spaces Connector refering the procedure mentioned in Cisco DNA Spaces: Connector Configuration Guide
After connecting Cisco AireOS Controller to Cisco DNA Spaces , configure radius authentication and internet provisioning as described in Configuring Cisco AireOS for Internet Provisioning and Radius Authentication.
If Captive Portal Authentication is required, import SSIDs, create captive portal with the required authentication type, and configure Captive Portal rule based on the procedure mentioned in chapter Working with the Captive Portal App
If social authentication is required for captive portal, configure social authentication as described in Configuring Cisco Wireless Controller for Social Authentication
If you want to send notifications using Cisco DNA Spaces, configure the engagement rules based on the procedure mentioned in chapter Sending Notifications with the Engagements App

Cisco Catalyst 9800 Series Wireless Controller with Cisco DNA Spaces Connector

To connect Cisco Catalyst 9800 Series Wireless Controller to Cisco DNA Spaces using a Cisco DNA Spaces Connector, and to configure captive portal authentication or notifications, do the following:

To connect Cisco Catalyst 9800 Series Wireless Controller to Cisco DNA Spaces using a Cisco DNA Spaces Connector, refer the procedure mentioned in Cisco DNA Spaces: Connector Configuration Guide"
After connecting Cisco Catalyst 9800 Series Wireless Controller to Cisco DNA Spaces , for social authentication, radius authentication, and internet provisioning (for using the Captive Portals app and Engagements app), refer to a matching section from the following :
To configure Captive Portal Authentication, import SSIDs, create captive portal with the required authentication type, and configure Captive Portal rule based on the procedure mentioned in chapter Working with the Captive Portal App
If you want to send notifications using Cisco DNA Spaces, configure the engagement rules based on the procedure mentioned in chapter Sending Notifications with the Engagements App

Configuring Mobility Express to work with Cisco DNA Spaces

This section describes the configurations to be done in the Mobility Express Controller for using Cisco DNA Spaces.

The configurations required for various Mobility Express versions are different. The configurations for various Mobility Express versions are as follows:

Configuring Mobility Express 8.7 or Later for Cisco DNA Spaces

To configure the Mobility Express 8.7 or later for Cisco DNA Spaces, perform the following steps:

Creating SSIDs in the Mobility Express

To create SSIDs in the Mobility Express, perform the following steps:

Procedure

Step 1	Log in to Mobility Express with your credentials.
Step 2	In the main window, click Wireless Settings in the left pane.
Step 3	Click WLANs.
Step 4	To create a WLAN, click Add new WLAN/RLAN.
Step 5	In the window that appears, in the General tab, enter the WLAN details like Type, Profile Name, SSID, and so on.
Step 6	Click Apply. The Add new WLAN/RLAN window appears.
Step 7	Click WLAN Security.
Step 8	Enable the Guest Network toggle switch.
Step 9	Enable the Captive Network Assistant toggle switch.
Step 10	From the Captive Portal drop-down list, choose External Splash Page.
Step 11	From the Access Type drop-down list, choose Web Consent.
Step 12	In the Captive Portal URL field that appears, enter the Cisco DNA Spaces splash URL. To view the splash URL for your ME account, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a CUWN SSID in the SSIDs window.
Step 13	Click Apply.
Step 14	To enable and broadcast the SSID, in the General tab, from the Admin drop-down list, choose “Enabled”, and enable the “Broadcast SSID” toggle switch.
Step 15	Execute the following command in the command prompt to disable the secure webauth mode. Then, restart the ME. `config network web-auth secureweb disable`
Step 16	Execute the following command in the command prompt to change the webauth login success page from Default to None. config custom-web webauth-login-success-page none

Configuring RADIUS Authentication in Mobility Express 8.7 or Later

To configure radius authentication in the Mobility Express 8.7 or later, perform the following steps:

Procedure

Step 1

Step 2

In the ME main window, click Switch to Expert View in the top right of the window.

Step 3

In the pop up window that appears, select OK.

Step 4

In the left pane, click Management > Admin Accounts.

Step 5

In the window that appears, click the Radius tab.

Step 6

Click Add RADIUS Authentication Server.

In the Add/ Edit Radius Authentication Server window appears, enter the following radius server details:

In the Server IP Address field, enter the IP address of the radius server.
In the Shared Secret field, enter your radius secret key.

In the Confirm Shared Secret field, re-enter the radius secret key.

Note

You can configure only the Cisco DNA Spaces radius servers. To view the IP address and secret key for radius server configuration, in the Cisco DNA Spaces dashboard, click the Captive Portal app. Click SSIDs, and then click the Configure Manually link for a Cisco Unified Wireless Network (Cisco AireOS) SSID. Click the Configure SSID in CUWN-WLC tab. The radius server details will be listed in the Radius Server Configuration section. Configure both the primary and secondary radius server IPs.You can also contact the Cisco DNA Spaces support team.

Step 7

Click Apply.

Step 8

In the Mobility Express main window, click Wireless Settings in the left pane.

Step 9

Click WLANs .

The WLAN/RLAN Configuration window appears with the SSIDs list.

Step 10

Click the Edit icon for the SSID created previously.

Step 11

In the Edit WLAN window that appears, click the WLAN Security tab.

Step 12

From the Access Type drop-down list, choose Radius.

Step 13

Click the Radius Server tab, and click Add RADIUS Authentication Server.

Step 14

From the Server IP Address drop-down list, select your Radius Server, and click Apply.

Step 15

In the Edit WLAN window, click Apply.

Now the Mobility Express 8.7 or later is configured for radius server authentication.

Creating Access Control Lists in Mobility Express 8.7 or Later

To create Access Control Lists in the Mobility Express 8.7 or later, perform the following steps:

Procedure

Step 1

Step 2

In the Mobility Express main window, click the Wireless Settings in the left pane.

Step 3

Click WLANs.

The WLAN/RLAN Configuration window appears with the SSIDs list.

Step 4

Click the Edit icon for the SSID created previously.

In the Edit WLAN window that appears, click the WLAN Security tab.

Step 5

Click the Pre Auth ACLs tab.

Step 6

Click Add IP Rules.

Step 7

In the Add/Edit IP ACLs, create rules with the following configuration:


Action	Source IP Address/Netmask	Destination IP Address/Netmask	Protocol	Source Port Range	Dest Port Range	DSCP
Permit	34.235.248.212/255.255.255.255	0.0.0.0/0.0.0.0	Any	Any	Any	Any
Permit	0.0.0.0/0.0.0.0	34.235.248.212/255.255.255.255	Any	Any	Any	Any
Permit	52.55.235.39/255.255.255.255	0.0.0.0/0.0.0.0	Any	Any	Any	Any
Permit	0.0.0.0/0.0.0.0	52.55.235.39/255.255.255.255	Any	Any	Any	Any

Note

For EU region, 34.235.248.212, 52.55.235.39 must be replaced with 54.77.207.183,34.252.175.120.

When defining the ACL rule, ensure to configure the values as follows:

Protocol: Any
DSCP: Any
Action: Permit

Step 8

Click Apply.

Configuring Mobility Express 8.7 or Later for Social Authentication

To configure the Mobility Express for Social Sign authentication for captive portals, perform the following steps:

Procedure

Step 1

Step 2

In the Mobility Express main window, click the Wireless Settings in the left pane.

Step 3

Click WLANs.

The WLAN/RLAN Configuration window appears with the SSIDs list.

Step 4

Click the Edit icon for the SSID created previously.

In the Edit WLAN window that appears, click the WLAN Security tab.

Step 5

Click the Pre Auth ACLs tab.

Step 6

Click Add IP Rules.

Step 7

In the Add/Edit IP ACLs, configure the following two rules in addition to the existing ACL rules:


Action	Source IP Address/Netmask	Destination IP Address/Netmask	Protocol	Source Port Range	Dest Port Range	DSCP
Permit	0.0.0.0/0.0.0.0	0.0.0.0/0.0.0.0	TCP	HTTPs	Any	Any
Permit	0.0.0.0/0.0.0.0	0.0.0.0/0.0.0.0	TCP	Any	HTTPS	Any

Allowing the URLs in the Mobility Express 8.7 or Later

To allow a URL in the Mobility Express 8.7 or later, perform the following steps:

Procedure

Step 1	Log in to ME with your credentials.
Step 2	In the ME main window, click the Wireless Settings in the left pane.
Step 3	Click WLANs. The WLAN/RLAN Configuration window appears with the SSIDs list.
Step 4	Click the Edit icon for the SSID created previously.
Step 5	In the Edit WLAN window that appears, click the WLAN Security tab.
Step 6	Click the Pre Auth ACLs tab.
Step 7	Click Add URL Rules.
Step 8	In the Add/Edit URL ACLs window that appears, configure the URL that you want to include in the allowed list. When defining the URL rule, ensure to configure the values as follows: URL: domain Action: Permit
Step 9	Click Update.

Configuring Mobility Express for Notifications and Reports

If you are using Mobility Express with WLC connect, to configure for location updates, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller CLI, execute the following commands:

config cloud-services cmx disable
config cloud-services server url https://{Customer Path Key}.{LB Domain} {LB IP Address}
config cloud-services server id-token {Customer JWT Token}
config network dns serverip <dns server ip>
config cloud-services cmx enable

Note

To view the {Customer Path Key}, {LB Domain}, {LB IP Address}, and {Customer JWT Token}, in the Cisco DNA Spaces dashboard, click the Configure Manually link for a CUWN SSID in SSIDs window. You can also contact the Cisco DNA Spaces support team. Ensure that there are no trailing or leading spaces.

Step 2

Check the summary using the following command:

show cloud-services cmx summary

The result appears.

Now in the Cisco DNA Spaces dashboard, when you choose CUWN-WLC in the Add a Wireless Network window, the WLC will be listed. So, you can import the APs of that WLC to the Cisco DNA Spaces.

Sample Resultt

(Cisco Controller) >show cloud-services cmx summary

CMX Service

Server ....................................... https://$customerpathkey.dnaspaces.io

IP Address.................................... 50.16.12.224

Connectivity.................................. https: UP

Service Status ............................... Active

Last Request Status........................... HTTP/1.1 200 OK

Heartbeat Status ............................. OK

What to do next

Now the Cisco Wireless Controller will be available for importing to the Cisco DNA Spaces location hierarchy. For more information on importing the Cisco Wireless Controller and its access points, follow from Step 4 of the procedure mentioned in Connecting Cisco DNA Spaces to Cisco Wireless Controller Using Cisco WLC Direct Connect.

Configuring Mobility Express 8.6 or Earlier for Cisco DNA Spaces

To configure Mobility Express 8.6 or earlier for Cisco DNA Spaces:

Creating SSIDs in Mobility Express 8.6 or Earlier

The steps to create SSIDs in Mobility Express 8.6 or earlier are same as that for Mobility Express 8.7 or later. To know the configuration steps, see the Creating SSIDs in the Mobility Express.

Configuring RADIUS Authentication for Mobility Express 8.6 or Earlier

In Mobility Express 8.6 or earlier, you cannot configure radius servers individually.

To configure Mobility Express 8.6 or earlier for RADIUS authentication, perform the following steps:

Procedure

Step 1

Step 2

In the Mobility Express main window, click Wireless Settings in the left pane.

Step 3

Click WLANs.

The WLAN/RLAN Configuration window appears with the SSIDs list.

Step 4

Click the Edit icon for the SSID created previously.

Step 5

In the Edit WLAN window that appears, click the WLAN Security tab.

Step 6

From the Access Type drop-down list, choose Radius.

Step 7

To add the radius server, click Add.

Step 8

In the window that appears, enter the following radius server details:

In the Server IP Address field, enter the IP address of the radius server.
In the Shared Secret field, enter your radius secret key.
In the Confirm Shared Secret field, re-enter the radius secret key.
Click Apply.

Note

Step 9

In the Edit WLAN window, click Apply.

Now, the Mobility Express is configured for radius server authentication of Cisco DNA Spaces captive portals.

Creating ACLs for Mobility Express 8.6 or Earlier

Mobility Express 8.6 or earlier does not provide user interface to configure Access Control Lists. So for creating ACLs, and configuring social authentication, you must use the command prompt. For the commands to use for these ACL configurations, see the “ Mobility Express Command Reference Guide”.

Now the Cisco Wireless Controller will be available for import in Cisco DNA Spaces location hierarchy. For more information on importing the Cisco Wireless Controller and access points to the Cisco Wireless Controller, follow from Step 3 of the procedure mentioned in Connecting Cisco DNA Spaces to Cisco Wireless Controller Using Cisco WLC Direct Connect.

Configuring Mobility Express for Notifications and Reports

If you are using Mobility Express with WLC connect, to configure for location updates, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller CLI, execute the following commands:

config cloud-services cmx disable
config cloud-services server url https://{Customer Path Key}.{LB Domain} {LB IP Address}
config cloud-services server id-token {Customer JWT Token}
config network dns serverip <dns server ip>
config cloud-services cmx enable

Note

Step 2

Check the summary using the following command:

show cloud-services cmx summary

The result appears.

Now in the Cisco DNA Spaces dashboard, when you choose CUWN-WLC in the Add a Wireless Network window, the WLC will be listed. So, you can import the APs of that WLC to the Cisco DNA Spaces.

Sample Resultt

(Cisco Controller) >show cloud-services cmx summary

CMX Service

Server ....................................... https://$customerpathkey.dnaspaces.io

IP Address.................................... 50.16.12.224

Connectivity.................................. https: UP

Service Status ............................... Active

Last Request Status........................... HTTP/1.1 200 OK

Heartbeat Status ............................. OK

What to do next

Configuring Aironet 4800 Series Mobility Express Controller 8.10.150.0 for Cisco DNA Spaces

To configure AireOS 4800 Series Mobility Express Controller 8.10.150.0 for Cisco DNA Spaces:

Configuring Mobility Express 8.10.150.0

To configure Mobility Express 8.10.105.0 for Cisco DNA Spaces, perform the following steps:

Procedure

Step 1

Step 2

Go to Advanced > Security Settings.

Step 3

Click Add New ACL.

Step 4

In the Add ACL Rule window, enter the ACL details:

From the ACL Type drop-down list, choose IPv4.
In the ACL name field, enter a name for the ACL.
Click Add URL Rules.

The Add /Edit URL ACLs window appears.
In the URL field, enter splash page URL domain.
From the Action drop-down list, choose Permit.
To enable social authentication, add the following domains in the ACL:
- *.facebook.com
- *.facebook.com
- ssl.gstatic.com
- static.licdn.com
- *.fbcdn.net
- *.akamaihd.net
- *.twitter.com
- *.twimg.com
- oauth.googleusercontent.com
- *.googleapis.com
- *.accounts.google.com
- *.gstatic.com
- *.linkedin.com
- *.licdn.net
- *.licdn.com
This step is required only of you want to enable social authentication.
Click Update.

Step 5

To add radius server configuration, perform the following steps:

Create an ACL.
Enable Expert view.
Go to Managenent > Admin Accounts > Radius
From the Authentication Call Station ID Type drop-down list, choose AP MAC Address:SSID.
From the Authentication MAC Delimiter drop-down list, choose Hyphen.
From the Accounting Call Station ID Type drop-down list, choose AP MAC Address:SSID.
From the Accounting MAC Delimiter drop-down list, choose Hyphen.
From the Fallback Mode drop-down list, choose Off.
Click Apply.

Step 6

Click Add Radius Authentication Server, and in the Add/Edit Radius Authentication Server that appears, enter the following details:

Disable CoA.
In the Server Ip Address field, enter the radius server IP address.
In the Shared Secret field, enter the secret key.
In the Confirm Shared Secret field, enter the secret key to confirm

Click Apply.

Added radius server will be listed under the Radius Servers list.

Note

You can configure only the Cisco DNA Spaces radius servers. To view the IP address and secret key for the radius server configuration, in the Cisco DNA Spaces dashboard, click the Captive Portalsapp. Click SSIDs, and then click the Configure Manually link for a Cisco Unified Wireless Network (Cisco AireOS) SSID. The radius server details will be listed in the Radius Server Configuration section. Configure both the primary and secondary radius server IPs. You can also contact the Cisco DNA Spaces support team.

Step 7

To configure WLAN for radius server, perform the following steps:

In the Cisco Aironet ME dashboard, choose Wireless Settings > WLAN.
Click the General tab.
In the Profile Name field, enter the SSID name.
From the Admin State drop-down list, choose Enabled.
From the Radio Policy drop-down list, choose ALL.
Click the WLAN Security tab.
Enable Guest Network.
Enable Captive Network Assistant.

In the Captive Portal URL field, enter the captive portal URL.

Note

To view the Captive Portal URL, in the Cisco DNA Spaces dashboard, click the Captive Portalsapp. Click SSIDs, and then click the Configure Manually link for a Cisco Unified Wireless Network (Cisco AireOS) SSID. Go to the Creating the SSIDs in WLC Direct Connect section. The URL is displayed at Step 7g.

From the Access Type, choose RADIUS.
In the ACL Name (IPV4), choose the ACL name configured at Step 4b.
For radius server, click Add Radius Authentication Server
Select Radius server IP added at Step 6b from the list.

Step 8

For Radius L2 Authentication, enable MAC Filtering and ON MAC Filter failure.

Step 9

Click Apply.

Configuring Mobility Express for Notifications and Reports

If you are using Mobility Express with WLC connect, to configure for location updates, perform the following steps:

Procedure

Step 1

In the Cisco Wireless Controller CLI, execute the following commands:

config cloud-services cmx disable
config cloud-services server url https://{Customer Path Key}.{LB Domain} {LB IP Address}
config cloud-services server id-token {Customer JWT Token}
config network dns serverip <dns server ip>
config cloud-services cmx enable

Note

Step 2

Check the summary using the following command:

show cloud-services cmx summary

The result appears.

Now in the Cisco DNA Spaces dashboard, when you choose CUWN-WLC in the Add a Wireless Network window, the WLC will be listed. So, you can import the APs of that WLC to the Cisco DNA Spaces.

Sample Resultt

(Cisco Controller) >show cloud-services cmx summary

CMX Service

Server ....................................... https://$customerpathkey.dnaspaces.io

IP Address.................................... 50.16.12.224

Connectivity.................................. https: UP

Service Status ............................... Active

Last Request Status........................... HTTP/1.1 200 OK

Heartbeat Status ............................. OK

SNO	Cisco DNA Spaces Connector	Cisco WLC Direct Connect		CMX Tethering Connector
Platforms	Cisco AireOS	Cisco AireOS	Cisco Catalyst 9800 Series	Cisco AireOS
Max Scale on supported appliance.	12.5K APs, 250K clients Incoming NMSP should not be more than 10.5K messages/sec.	50 APs and 50 Clients	50 APs and 50 Clients	60K clients, 5K APs, and 50k RFID tags Maps with 1BLDG-100 Floors and each floor with 50 APs
Scale supported releases	Connector version 2.1.1 with docker v2.0.204	8.8MR2	16.12, 17.1	8.8MR2 with CMX 10.6 (high end)

Results

Chapter: Configuring Cisco Wireless Controllers and Cisco Catalyst 9800 Series Controllers for Cisco DNA Spaces

Configuring Cisco Wireless Controllers and Cisco Catalyst 9800 Series Controllers for Cisco DNA Spaces

Features Supported by Various Connectors

Connecting Cisco DNA Spaces to Cisco Wireless Controller through Cisco CMX

Configuring Access Point Mode, SSIDs, ACLs, Splash URLs, and Virtual Interface in the WLC

Local Mode Configurations for Using Cisco DNA Spaces

Configure the Local Mode for an Access Point

Procedure

Create SSIDs in Cisco Wireless Controller

Procedure

What to do next

Create Access Control Lists

Procedure

Configure the Virtual Interface

Procedure

FlexConnect Mode Configurations for Using Cisco DNA Spaces

FlexConnect Central Switch Mode

Configure the FlexConnect Mode for an Access Point

Procedure

Create SSIDs in the Cisco Wireless Controller for FlexConnect Central Switch Mode

Create Access Control Lists for FlexConnect Central Switch Mode

Configure the Virtual Interface

Procedure

FlexConnect Local Switch Mode

Configure the FlexConnect Mode for an Access Point

Procedure

Create SSIDs in the Cisco Wireless Controller for the FlexConnect Local Switch Mode

Procedure

Create Access Control Lists for FlexConnect Local Switch Mode

Procedure

Configure the Virtual Interface

Procedure

Configuring Cisco Wireless Controller for Internet Provisioning and RADIUS Authentication

Procedure

Configuring Cisco Wireless Controller for Social Authentication

Procedure

Connecting Cisco Catalyst 9800 Series Wireless Controller or Cisco Wireless Controller to Cisco DNA Spaces Using WLC Direct Connect or Cisco DNA Spaces Connector

Connecting Cisco DNA Spaces to Cisco Wireless Controller Using Cisco WLC Direct Connect

Before you begin

Procedure

Example:

What to do next

Configuring Cisco Wireless Controller (without Cisco CMX) for Notification and Reports

Connecting Cisco DNA Spaces to Cisco Catalyst 9800 Series Wireless Controller Using Cisco WLC Direct Connect

Before you begin

Procedure

Example:

Configuring Cisco Catalyst 9800 Series Wireless Controller (Local Mode) for Captive Portals and Engagements Apps Using CLI

Procedure

Configuring Cisco Catalyst 9800 Series Wireless Controller GUI (Local Mode) for Captive Portals and Engagements Apps

Procedure

Configuring Cisco Catalyst 9800 Series Wireless Controller GUI (Flex Mode or Mobility Express) for Captive Portals and Engagements Apps

Procedure

Connecting Cisco DNA Spaces to Cisco AireOS Wireless Controller or Cisco Catalyst 9800 Series Wireless Controller using Cisco DNA Spaces Connector

Configuring Mobility Express to work with Cisco DNA Spaces

Configuring Mobility Express 8.7 or Later for Cisco DNA Spaces

Creating SSIDs in the Mobility Express

Procedure

Configuring RADIUS Authentication in Mobility Express 8.7 or Later

Procedure

Creating Access Control Lists in Mobility Express 8.7 or Later

Procedure

Configuring Mobility Express 8.7 or Later for Social Authentication

Procedure

Allowing the URLs in the Mobility Express 8.7 or Later

Procedure

Configuring Mobility Express for Notifications and Reports

Procedure

What to do next

Configuring Mobility Express 8.6 or Earlier for Cisco DNA Spaces

Creating SSIDs in Mobility Express 8.6 or Earlier

Configuring RADIUS Authentication for Mobility Express 8.6 or Earlier

Procedure

Creating ACLs for Mobility Express 8.6 or Earlier

Configuring Mobility Express for Notifications and Reports

Procedure

What to do next

Configuring Aironet 4800 Series Mobility Express Controller 8.10.150.0 for Cisco DNA Spaces

Configuring Mobility Express 8.10.150.0