Unified CCX: SSO Configuration
First Published: September 14, 2016
This page provides configuration information for single sign-on (SSO) in the Cisco Unified Contact Center Express (Unified CCX) environment.
SSO is a session or user authentication process that permits a user to provide credentials to access one or more applications. The process authenticates the user for all applications they have been given rights to and eliminates further prompts when they switch applications during a particular session.
The intended audience should be able to perform system-level configuration of Cisco Collaboration components and deployments and be familiar with Cisco Collaboration products.
The configuration information is based primarily on system testing performed during Cisco Collaboration Systems Release 11.5(1).
This topic does not contain detailed step-by-step procedures; for detailed information about installing, configuring, and administering Unified CCX refer to product documentation, see the Related Documentation section.
For information on design considerations and guidelines for deploying Unified CCX, see: Cisco Unified Contact Center Express Design Guide.
For information on specific deployments and sites where Context service system testing was performed, see Cisco Unified Contact Center Express Test Bed for Collaboration Systems Release 11.5(1).
This section provides information about the Unified CCX deployment. During Cisco Collaboration Systems 11.5(1) testing, various system components were installed, integrated, and tested in several sites.
This section provides the high-level tasks and related information for configuring for configuring Context Service in Unified CCX environment
The following table provides this information:
■ Configuration Tasks: List of high-level configuration tasks.
■ System Test Specifics: System test variations from procedures and settings documented in the product documentation.
■ More Information: Links to product documentation for detailed configuration information related to the high-level tasks.
Note: Default and recommended values specified in the product documentation were used during system testing, unless otherwise noted in the System Test Specifics column.
Table 1. Unified CCX SSO Configuration
■ For installation and configuration information on Unified CCX and other related products, see the product support guides in System Release Notes for Contact Center: Cisco Collaboration Systems Release 11.5(1).
■ For information on the IOS commands used to configure infrastructure components, see Unified CCX Test Bed Configuration Command Files for CSR 11.5(1).
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation.
To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What’s New in Cisco Product Documentation RSS feed. The RSS feeds are a free service.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
All printed copies and duplicate soft copies are considered un-Controlled copies and the original on-line version should be referred to for latest version.
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
© 2016 Cisco Systems, Inc. All rights reserved.