Administration Guide for Cisco Unified SRST Manager

Cisco Unified SRST Manager uses the Network Time Protocol (NTP) server for clocking functions. Use the show clock command to display the Cisco Unified SRST Manager clock status.

Examples

The following is sample output for the show clock command:

srstmgr-1# show clock

19:20:33.724 PST Wed Mar 17 1993

time zone: America/Los_Angeles

clock state: unsync

delta from reference (microsec): 0

estimated error (microsec): 175431

time resolution (microsec): 1

clock interrupt period (microsec): 10000

time of day (sec): 732424833

time of day (microsec): 760817

Table 16 describes the significant fields shown in the display.

Table 16 show clock Field Descriptions
Field	Description
time zone	Current time zone setting.
clock state	Synchronization state of the clock.
delta from reference (ms)	Difference between the module clock and the NTP reference clock.
time of day (sec)	Current time of day in seconds.
time of day (ms)	Current time of day in microseconds.

Related Commands

Command	Description
ntp server	Specifies the NTP server for Cisco Unified SRST Manager.
show ntp	Displays the time source for an NTP server.

show configuration

To display the contents of the non-volatile memory, use the show configuration command in EXEC mode.

show configuration

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

Use this command for troubleshooting.

Examples

The following is sample output for the show configuration command:

se-1-100-100-100# show configuration

! This adds all the platform CLI commands

! host name

hostname se-1-100-100-100

! domain name

ip domain-name localdomain

! DNS Servers

ip name-server 1.100.100.100

! Timezone Settings

clock timezone America/Los_Angeles

! NTP Servers

!VAR_NTP_SERVER

! INTERFACE_F0

interface Ethernet 0

ip address 1.100.100.100 255.255.0.0

end interface

! DEFAULT GATEWAY

ip default-gateway 1.100.100.100

End

Related Commands

Command	Description
backup category	Specifies the type of data to be backed up and initiates the backup process.
hostname	Specifies the hostname of the current messaging gateway.
ip domain-name	Specifies the local messaging gateway’s domain name and/or domain name server.
restore factory default	Restores factory default settings.

show interfaces

To display the IP configuration and statistics for the Ethernet interface, use the show interfaces command in privileged EXEC mode.

show interfaces

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Version	Modification
9.0	This command was introduced.

Examples

The following is sample output for the show interfaces command:

se-192-100-1-1# show interfaces

Ethernet 0 is up, line protocol is up

Internet address is 192.100.1.1 mask 255.255.255.0 (configured locally)

5188306 packets input, 0 bytes

25113 input errors, 0 dropped, 0 overrun, 0 frame errors

10791446 packets output, 0 bytes

20301 output errors, 0 dropped, 0 overrun, 0 collision errors

0 output carrier detect errors

Related Commands

Command	Description
ip name-server	Specifies the domain name server.

show ip dns cache

To display the DNS cache, use the show ip dns cache command in EXEC mode.

show ip dns cache

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Version	Modification
9.0	This command was introduced.

Examples

The following is sample output for the show ip dns cache command:

srstmgr-1> show ip dns cache

srstmgr-1.unspecified. 2147483647 IN A 192.0.2.24

localhost.\(none\). 2147483647 IN A 192.0.2.23

192.0.2.22.in-addr.arpa. 2147483647 IN PTR localhost.

stress-umg1-192.0.2.24.example.com. 2147483647 IN A 192.0.2.24

192.0.2.24.in-addr.arpa. 2147483647 IN PTR 192.0.2.24.te

mp.com.

se-192.0.2.24.localdomain. 2147483647 IN A 192.0.2.24

sundial1-umg-se-192.0.2.24.localdomain. 2147483647 IN A 10.1.12.95

localhost.temp.com. 2147483647 IN A 192.0.2.18

192.0.2.24.temp.com. 2147483647 IN A 192.0.2.24

192.0.2.24.\(none\). 2147483647 IN A 192.0.2.24

stress-umg1-192.0.2.24.example.com. 2147483647 IN A 192.0.2.24

localhost. 2147483647 IN A 192.0.2.20

stress-umg1-192.0.2.22.\(none\). 2147483647 IN A 192.0.2.24

se-192.0.2.24.example.com. 2147483647 IN A 192.0.2.24

localhost.cisco.com. 2147483647 IN A 192.0.2.23

se-10-1-12-95>

Related Commands

Command	Description
hostname	Specifies the hostname for the current configuring Cisco Unified SRST Manager.
ip name-server	Specifies the domain name server.
ntp server	Specifies the NTP clocking server.
show hosts	Displays all configured hosts.

show license status

To display the license agreement, use the show license status command in EXEC mode.

show license status

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Version	Modification
9.0	This command was introduced.

Examples

The following is sample output for the show license status command:

se-1-100-80-203# show license status

LICENSE AGREEMENT

=================

PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR

LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH

PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING

TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND

BOUND BY ALL THE TERMS SET FORTH HEREIN.

You hereby acknowledge and agree that the product feature license

is terminable and that the product feature enabled by such license

may be shut down or terminated by Cisco after expiration of the

applicable term of the license (e.g., 30-day trial period). Cisco

reserves the right to terminate or shut down any such product feature

electronically or by any other means available. While alerts or such

messages may be provided, it is your sole responsibility to monitor

your terminable usage of any product feature enabled by the license

and to ensure that your systems and networks are prepared for the shut

down of the product feature. You acknowledge and agree that Cisco will

not have any liability whatsoever for any damages, including, but not

limited to, direct, indirect, special, or consequential damages related

to any product feature being shutdown or terminated.

show log name

To display logging data, use the show log name command in EXEC mode.

show log name word [ containing expression | paged | tail ]

Syntax Description

word	The name of the log file to display. Use the show logs command to display a list of available log files.
containing expression	Only displays events that match a search expression.
paged	Displays in paged mode.
tail	Displays the latest events as they occur.

Command Modes

EXEC

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This command has the following filtering options:

show begin : Begins the output of any show command from a specified string.
show exclude : Filters show command output so that it excludes lines that contain a particular regular expression.
show include : Filters show command output so that it displays only lines that contain a particular regular expression.

Examples

The following partial output for the show log name command displays the dmesg log:

srstmgr-1# show log name dmesg

Press <CTRL-C> to exit...

Linux version 2.4.24 (bld_adm@bld-system) (gcc version 2.95.3 20010315 (version4

Platform: nm

setup.c: handling flash window at [15MB..16MB]

setup.c: handling kernel log buf at [245.5MB]

setup.c: handling trace buf at [246MB]

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009f400 (usable)

BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000e0800 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 0000000000f00000 (usable)

BIOS-e820: 0000000000f00000 - 0000000001000000 (reserved)

BIOS-e820: 0000000001000000 - 000000000f580000 (usable)

BIOS-e820: 000000000f580000 - 000000000f600000 (reserved)

BIOS-e820: 000000000f600000 - 0000000010000000 (reserved)

BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)

245MB LOWMEM available.

On node 0 totalpages: 62848

zone(0): 4096 pages.

zone(1): 58752 pages.

zone(2): 0 pages.

DMI not present.

Kernel command line: root=/dev/hda1 ro plat=nm

Initializing CPU#0

Detected 498.674 MHz processor.

Calibrating delay loop... 996.14 BogoMIPS

Memory: 245128k/251392k available (1164k kernel code, 4852k reserved, 667k data)

kdb version 4.3 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reservd

in atrace_init

log_head: h: 0, t: 8429274, l: 0, w: 0, s: 10484672

Using existing trace log

log_head: h: 0, t: 8429274, l: 0, w: 0, s: 10484672

Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)

Inode cache hash table entries: 16384 (order: 5, 131072 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)

Page-cache hash table entries: 65536 (order: 6, 262144 bytes)

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 256K

CPU serial number disabled.

The following sample output for the show log command displays the dmesg log using a search string:

srstmgr-1# show log name dmesg containing setup

Press <CTRL-C> to exit...

setup.c: handling flash window at [15MB..16MB]

setup.c: handling kernel log buf at [245.5MB]

setup.c: handling trace buf at [246MB]

srstmgr-1#

The following partial output for the show log command displays the dmesg log in paged mode:

srstmgr-1# show log name dmesg paged

Linux version 2.4.24 (bld_adm@bld-system) (gcc version 2.95.3 20010315 (version

)) #1 Tue Nov 30 23:07:21 PST 2007

Platform: nm

setup.c: handling flash window at [15MB..16MB]

setup.c: handling kernel log buf at [245.5MB]

setup.c: handling trace buf at [246MB]

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009f400 (usable)

BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000e0800 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 0000000000f00000 (usable)

BIOS-e820: 0000000000f00000 - 0000000001000000 (reserved)

BIOS-e820: 0000000001000000 - 000000000f580000 (usable)

BIOS-e820: 000000000f580000 - 000000000f600000 (reserved)

BIOS-e820: 000000000f600000 - 0000000010000000 (reserved)

BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)

245MB LOWMEM available.

On node 0 totalpages: 62848

zone(0): 4096 pages.

zone(1): 58752 pages.

zone(2): 0 pages.

DMI not present.

Kernel command line: root=/dev/hda1 ro plat=nm

Initializing CPU#0

-- More --

The following output for the show log name command displays the current dmesg log as events are being entered:

srstmgr-1# show log name dmesg tail

Press <CTRL-C> to exit...

Freeing unused kernel memory: 88k freed

The following partial output for the show log name command displays the dmesg log beginning with the first line starting with ide0:

srstmgr-1# show log name dmesg | begin ide0

ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio

ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio

hda: C/H/S=50127/232/176 from BIOS ignored

hdb: C/H/S=0/0/0 from BIOS ignored

hda: IC25N020ATMR04-0, ATA DISK drive

blk: queue c030c160, I/O limit 4095Mb (mask 0xffffffff)

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

hda: attached ide-disk driver.

hda: host protected area => 1

hda: 39070080 sectors (20004 MB) w/1740KiB Cache, CHS=2432/255/63, UDMA(33)

init unit number == 0

Related Commands.

Command	Description
log console	Configures the types of messages to be displayed on the console.
log console monitor	Displays system messages on the console.
log server address	Specifies an external server for saving log messages.
log trace boot	Saves the trace configuration on rebooting.
log trace buffer save	Saves the current trace information.
show logging	Shows the types of messages that are displayed on the console.
show logs	Displays the list of available logs.

show ntp

To display the time source for a Network Time Protocol (NTP) server, use the show ntp command in EXEC mode.

show ntp [ detail ]

Syntax Description

detail

Displays detailed information about the NTP servers.

Command Modes

EXEC

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This command displays the chain of NTP servers back to their primary time source, starting from the local host.

Examples

The following is sample output for the show ntp command:

srstmgr-1# show ntp

192.0.2.24: stratum 9, offset 0.000015, synch distance 0.03047

192.0.2.23: stratum 8, offset -0.001124, synch distance 0.00003

Table 17 describes the significant fields shown in the display.

Table 17 show ntp Field Descriptions
Field	Description
(first field)	IP address of the host.
stratum	Server hop count to the primary clock source. Valid values are: 0—Unspecified 1—Primary clock reference 2–255—Secondary reference via NTP
offset	Time offset between the host and the local host, in seconds.
synch distance	Host synchronization distance, which is the estimated error relative to the primary source.

The following is sample output for the show ntp detail command:

srstmgr-1# show ntp detail

server 192.0.2.24, port 123

stratum 9, precision -17, leap 00

refid [192.0.2.22] delay 0.00012, dispersion 0.00000 offset 0.000011

rootdelay 0.00058, rootdispersion 0.03111, synch dist 0.03140

reference time: af4a3ff7.926698bb Thu, Mar 11 1993 14:47:19.571

originate timestamp: af4a4041.bf991bc5 Thu, Mar 11 1993 14:48:33.748

transmit timestamp: af4a4041.bf90a782 Thu, Mar 11 1993 14:48:33.748

server 192.0.2.23, port 123

stratum 8, precision -18, leap 00

refid [192.0.2.21] delay 0.00024, dispersion 0.00000 offset -0.001130

rootdelay 0.00000, rootdispersion 0.00003, synch dist 0.00003

reference time: af4a402e.f46eaea6 Thu, Mar 11 1993 14:48:14.954

originate timestamp: af4a4041.bf6fb4d4 Thu, Mar 11 1993 14:48:33.747

transmit timestamp: af4a4041.bfb0d51f Thu, Mar 11 1993 14:48:33.748

Table 18 describes the significant fields shown in the display.

Table 18 show ntp detail Field Descriptions
Field	Description
server	IP address of the host server.
port	Port number of the host server.
stratum	Server hop count to the primary clock source. Valid values are: 0—Unspecified 1—Primary clock reference 2–255—Secondary reference via NTP
precision	Precision of the clock, in seconds to the power of two.
leap	Two-bit code warning of an impending leap second to be inserted in the NTP time scale. Valid values are: 00—No warning 01—Last minute was 61 seconds 10—Last minute was 59 seconds 11—Alarm condition (clock not synchronized)
refid	IP address of the peer selected for synchronization.
delay	Round-trip delay of the packet, in milliseconds.
dispersion	Measure, in milliseconds, of how scattered the time offsets have been from a given time server.
offset	Time offset between the host and the local host, in seconds.
rootdelay	Total round-trip delay, in seconds, to the primary reference source at the root of the synchronization subnet.
rootdispersion	Maximum error, in seconds, relative to the primary reference source at the root of the synchronization subnet.
synch dist	Host synchronization distance, which is the estimated error relative to the primary source.
reference time	Local time, in time-stamp format, when the local clock was last updated. If the local clock has never been synchronized, the value is zero.
originate timestamp	Local time, in time-stamp format, at the peer when its latest NTP message was sent. If the peer becomes unreachable, the value is zero.
transmit timestamp	Local time, in time-stamp format, when the latest NTP message from the peer arrived. If the peer becomes unreachable, the value is zero.

Related Commands

Command	Description
ntp server	Configures the Network Time Protocol (NTP) server to keep the system time synchronized with the NTP server.
show clock	Displays clock statistics.

show srsx central-call-agent

To display the list of configured Cisco Unified Communications Manager systems or details for the specified Cisco Unified Communications Manager system, use the show srsx central-call-agent command.

show srsx central-call-agent [ hostname [ srst-references | nodes ]]

Syntax Description

hostname	Hostname of a specific Cisco Unified Communications Manager system.
srst-references	Displays the Cisco Unified SRST references for the specified Cisco Unified Communications Manager system.
nodes	Displays all the nodes discovered for the Cisco Unified Communications Manager system.

Command Modes

EXEC mode

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This information is also available in the Cisco Unified SRST Manager graphical user interface, which we recommend that you use as the primary administrative interface.

Examples

The following is an example of the show srsx central-call-agent command:

srstmgr-1# show srsx central-call-agent

Name |Provisioning|SRST-References

__________________________________

CUCM8|enabled |7

The following is an example of the show srsx central-call-agent command with a central call agent specified:

srstmgr-1# show srsx central-call-agent CUCM8

Name: CUCM8

AXL Username: Administrator

AXL Password: *******

AXL Pacing: 0 (milliseconds)

Provisioning Schedule: Every day at 12:00 am

Default Voicemail: CUC 8.5

Provisioning: enabled

Site Provision Enable Default: enabled

Primary Node: CentralCA.srst.bxb.lab

Secondary Node: CentralCA2.srst.bxb.lab

The following is an example of the show srsx central-call-agent command with a central call agent specified and asking for a list of the Cisco Unified SRST references:

srstmgr-1# show srsx central-call-agent ccm ccm.cisco.com srst-references

SRST-references |IP Address

_______________________________________

branch-bos-srst |192.168.1.2

branch-nyc-srst |192.168.1.4

branch-sj-srst |192.168.1.5

The following is an example of the show srsx central-call-agent command with a central call agent specified and asking for a list of the nodes discovered for the central call agent:

srstmgr-1# show srsx central-call-agent CUCM8 nodes

Nodes

_______________________________________

CentralCA.srsv.bxb.lab

CentralCA2.srsv.bxb.lab

Related Commands

Command	Description
show srsx site	Displays the sites on the Cisco Unified SRST system.

show srsx provisioning-history

To display the provisioning history for all sites, use the show srsx provisioning-history command.

show srsx provisioning-history

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC mode

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This information is also available in the Cisco Unified SRST Manager graphical user interface, which we recommend that you use as the primary administrative interface.

Examples

The following is an example of the show srsx provisioning-history command in Cisco Unified SRST Manager 9.0:

srstmgr-1# show srsx provisioning-history

Site |Last Result|Date |Last Success |Users Provisioned

_________________________________________________________________________________________

branch-bos-srst|Success |Mon, Mar 22, 09:24 AM|Mon, Mar 22, 09:24 AM|21

branch-nyc-srst|unknown | | |0

branch-sj-srst |unknown | | |0

The following is an example of the show srsx provisioning-history command in Cisco Unified SRST Manager 9.0:

srstmgr-1# show srsx provisioning-history

Site |Last Result|Date |Last Success |Users Provisioned

_________________________________________________________________________________________

branch-bos-srst|Success |Mon, Mar 22, 09:24 AM|Mon, Mar 22, 09:24 AM|21

branch-nyc-srst|unknown | | |0

branch-sj-srst |unknown | | |0

Related Commands

Command	Description
show srsx central-call-agent	Displays the central call agents available on the Cisco Unified SRST system.
show srsx site	Displays the sites on the Cisco Unified SRST system.

show srsx site

To display the list of sites managed by the Cisco Unified SRST Manager or to see details for the specified site, use the show srsx site command.

show srsx site [ sitename ]

Syntax Description

sitename

Name of a specific site.

Command Modes

EXEC mode

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This information is also available in the Cisco Unified SRST Manager graphical user interface, which we recommend that you use as the primary administrative interface.

Examples

The following is an example of the show srsx site command:

srstmgr-1# show srsx site

Site |Provisioning |Call Agent |SRST |SRST

__________________________________________________________________________________________

srst1 |enabled |CUCM8 |192.168.1.2 |bos-srst.srst.lab

srst1 |enabled |CUCM8 |192.168.1.4 |bos-srst.srst.lab

srst2 |enabled |CUCM7 |192.168.1.5 |bos-srst.srst.lab

The following is an example of the show srsx site command with a site specified:

srstmgr-1# show srsx site srst1

Sitename: srst1

Central Call Agent: CUCM8

Central Voicemail Server: CUC 8.5

Srst Reference: srst1

Srst Address: 192.168.28.131

Template: default

Provisioning: enabled

SRST provisioning enabled

Router login username bxb100 admin

Router login password *******

Related Commands

Command	Description
show srsx central-call-agent	Displays the central call agents available on the Cisco Unified SRST system.

show srsx site-template

To display the site provisioning templates used when provisioning Cisco Unified SRST Manager devices, use the show srsx site-template command.

show srsx site-template [ default ] | [ name ] | [ auto-learned ]

Syntax Description

default	Displays default site provisioning templates.
name	Displays details for the selected template.
auto-learned	Displays site provisioning templates for auto-learned sites.

Command Modes

EXEC mode

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This information is also available in the Cisco Unified SRST Manager graphical user interface, which we recommend that you use as the primary administrative interface.

Examples

The following is an example of the show srsx site-template command in which the voicemail pilot has been auto-learned:

se-1-100-100-100# show srsx site-template

Name |Voicemail Pilot|

___________________________________

default |Auto-Learned |

ESRST_and_Dialplan|Auto-Learned |

ESRST_only |Auto-Learned |

SRST_and_Dialplan |Auto-Learned |

SRST_only |Auto-Learned |

Related Commands

Command	Description
show srsx central-call-agent	Displays the central call agents available on the Cisco Unified SRST system.
show srsx site	Displays the sites on the Cisco Unified SRST system.

show srsx system-settings

To display the global Cisco Unified survivable remote system configuration values, use the show srsx system-settings command.

show srsx system-settings

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC mode

Command History

Version	Modification
9.0	This command was introduced.

Usage Guidelines

This information is also available in the Cisco Unified SRST Manager GUI, which we recommend that you use as the primary administrative interface.

Examples

The following is an example of the show srsx system-settings command:

srstmgr-1# show srsx system-settings

Use TLS Security: Off

Related Commands

Command	Description
show srsx central-call-agent	Displays the central call agents available on the Cisco Unified SRST Manager system.
show srsx site	Displays the sites on the Cisco Unified SRST Manager system.

Bias-Free Language

Results

Chapter: S

S

show clock

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show configuration

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show interfaces

Syntax Description

Command Modes

Command History

Examples

Related Commands

show ip dns cache

Syntax Description

Command Modes

Command History

Examples

Related Commands

show license status

Syntax Description

Command Modes

Command History

Examples

show log name

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands.

show ntp

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show srsx central-call-agent

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show srsx provisioning-history

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show srsx site

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show srsx site-template

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show srsx system-settings

Syntax Description