Installing Solaris 10 Version 0708-V01 on Sun Netra T2000
Available Languages
Table Of Contents
Installing Solaris 10 Version 0708-V01
on Sun Netra T2000Checking the Installed Version of Firmware
Platform-Specific Installation Procedure
Installing Solaris 10 Version 0708-V01
on Sun Netra T2000
Revised: April, 2010, OL-11618-16Overview
This document provides the procedures you must complete to:
•
Enable RAID 0 on a Sun Netra T2000 platform
•
Note
Note
Caution
After you successfully install the Solaris 10 image on the Netra T2000 host machine, you can proceed to install the Solaris 10 Environment patches, the Cisco BAMS 3.30 Base Build, and the latest Cisco BAMS 3.30 patch.
This document does not cover installation of Solaris 10 Environment patches, the Cisco BAMS 3.30 Base Build, nor Cisco BAMS 3.30 patches. See the following documents for installation instructions:
•
Note
•
•
Hardware Compatibility
The Sun Solaris 10 operating system (Version 0708-V01) referred to in this appendix is intended to run on a Sun Netra T2000 platform.
Caution
Checking the Installed Version of Firmware
The following two sample commands show how to check the currently installed version of the firmware on a Sun Netra T2000 server.
Example 1
# prtconf -VOBP 4.30.0 2008/12/11 12:16Example 2
#.sc> showhostSystem Firmware 6.7.0 Netra[TM] T2000 2008/12/11 14:56Host flash versions:OBP 4.30.0 2008/12/11 12:16Hypervisor 1.7.0 2008/12/11 13:43Netra[TM] T2000 POST 4.30.0 2008/12/11 12:46sc> consoleInstalling Patch 137141-01
After you install the Sun operating system, you must download the patch from http://www.sunsolve.sun.com/ and place it in the path /var/spool/patch/.
Install the required patch by issuing the following command.
patchadd /var/spool/patch/137141-01Precautions
This section presents precautions you should consider before you perform any of the following installation procedures. When you begin to perform one of the installation procedures, you cannot back out.
•
–
–
Caution
•
Note
Prerequisite Checklist
Before you start the procedures in this appendix, complete the tasks listed in the following checklist.
1.
2.
3.
4.
a.
–
–
–
–
–
5.
RAID 0 Setup (Optional)
RAID 0 enables you to construct a logical volume made up of 2 or more physical disks, to increase Cisco BAMS performance. The Sun Netra T2000 server's on-board disk controller supports both RAID 0 and RAID 1 volumes.
You configure a RAID 0 volume on Netra T2000 by initializing the volume across 2 or 4 physical disks. This means that the Cisco BAMS billing, measurements, and intermediate files data is written across each physical disk in turn or striping the files across the disks. Configuring a RAID 0 volume improves the performance of Cisco BAMS but it does not provide redundancy. Therefore, you incur an increased risk of data loss. If a single disk fails, the entire volume fails and you must delete the volume and reconstruct it.
Caution
Cisco recommends enabling RAID 0 only when the Cisco BAMS is connected to a Cisco PGW2200 Softswitch that is running a high volume of calls per second, which requires improved performance.
All disks in a RAID 0 volume must the same size.
For a Cisco BAMS that is in service and running on a Sun Netra T2000 without RAID, if you re-install the server with RAID 0, all data and the operating system will be deleted. Therefore, before you attempt to re-install the server with RAID 0, first you must backup all data and transfer files to another server.
Setting Up a RAID 0 Volume
To set up RAID 0, complete the following steps.
Step 1
Step 2
Step 3
Step 4
# halt
Oct 28 00:13:40 sh-netra-T2000 halt: halted by rootOct 28 00:13:41 sh-netra-T2000 syslogd: going down on signal 15SNMP Research DR-Web EMANATE Agent Version 16.1.0.44Copyright 1989-2005 SNMP Research, Inc.syncing file systems... doneProgram terminatedStep 5
ok boot cdrom -s
Text similar to the following is displayed.
SC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set|Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: /pci@7c0/pci@0/pci@1/pci@0/ide@8/cdrom@0,0:f File and args: -sSunOS Release 5.10 Version Generic_120011-14 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Booting to milestone "milestone/single-user:default".Configuring devices.Using RPC Bootparams for network configuration information.Attempting to configure interface e1000g3...Skipped interface e1000g3Attempting to configure interface e1000g2...Skipped interface e1000g2Attempting to configure interface e1000g1...Skipped interface e1000g1Attempting to configure interface e1000g0...Configured interface e1000g0Requesting System Maintenance ModeSINGLE USER MODE#Step 6
# raidctl
Controller: 0Disk: 0.1.0Disk: 0.3.0Step 7
Note
# raidctl -C "0.1.0 0.3.0" -r 0 0Creating RAID volume will destroy all data on spare space of member disks, proceed (yes/no)? yes/pci@780/pci@0/pci@9/scsi@0 (mpt0):Physical disk 0 created./pci@780/pci@0/pci@9/scsi@0 (mpt0):Physical disk 1 created./pci@780/pci@0/pci@9/scsi@0 (mpt0):Volume 1 created./pci@780/pci@0/pci@9/scsi@0 (mpt0):Volume 1 is |enabled||optimal|/pci@780/pci@0/pci@9/scsi@0 (mpt0):Volume 1 is |enabled||optimal|Volume c0t1d0 is created successfully!Volume Size Stripe Status Cache RAIDSub Size LevelDisk----------------------------------------------------------------c0t1d0 N/A 64K OPTIMAL OFF RAID00.1.0 N/A GOOD0.3.0 N/A GOODStep 8
# raidctl -lController: 0Volume:c0t1d0Disk: 0.1.0Disk: 0.3.0To display RAID status, you need to include the name of the RAID volume in raidctl -l command# raidctl -l c0t1d0Volume Size Stripe Status Cache RAIDSub Size LevelDisk----------------------------------------------------------------c0t1d0 273.3G 64K OPTIMAL N/A RAID00.3.0 136.6G GOOD0.1.0 136.6G GOOD
Note
Step 9
Note
# formatSearching for disks...doneAVAILABLE DISK SELECTIONS:0. c0t1d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>/pci@780/pci@0/pci@9/scsi@0/sd@1,0Specify disk (enter its number): 0selecting c0t1d0[disk formatted]FORMAT MENU:disk - select a disktype - select (define) a disk typepartition - select (define) a partition tablecurrent - describe the current diskformat - format and analyze the diskrepair - repair a defective sectorlabel - write label to the diskanalyze - surface analysisdefect - defect list managementbackup - search for backup labelsverify - read and display labelssave - save new disk/partition definitionsinquiry - show vendor, product and revisionvolname - set 8-character volume name!<cmd> - execute <cmd>, then returnquitStep 10
format> typeAVAILABLE DRIVE TYPES:0. Auto configure1. Quantum ProDrive 80S2. Quantum ProDrive 105S3. CDC Wren IV 94171-3444. SUN01045. SUN02076. SUN03277. SUN03408. SUN04249. SUN053510. SUN066911. SUN1.0G12. SUN1.0513. SUN1.3G14. SUN2.1G15. SUN2.9G16. Zip 10017. Zip 25018. Peerless 10GB19. SUN146G20. otherSpecify disk type (enter its number)[19]: 0c0t1d0: configured with capacity of 272.99GB<LSILOGIC-LogicalVolume-3000 cyl 65533 alt 2 hd 32 sec 273>selecting c0t1d0[disk formatted]Step 11
format> labelReady to label disk, continue? yesStep 12
format> diskAVAILABLE DISK SELECTIONS:0. c0t1d0 <LSILOGIC-LogicalVolume-3000 cyl 65533 alt 2 hd 32 sec 273>/pci@780/pci@0/pci@9/scsi@0/sd@1,0Specify disk (enter its number)[0]: 0selecting c0t1d0[disk formatted]format>
Note
Step 13
The RAID volume is now ready for installation of the Solaris 10 Jumpstart image.
Step 14
Deleting a RAID Volume
You can use the procedure in this section to delete a RAID volume when it is not required. When you delete a RAID volume, all data on the disks is lost and you must re-install the Solaris 10 operating system. If your Cisco BAMS is in service and running on a Sun Netra T2000 server, perform a data backup and transfer the files to another server before you delete the RAID volume.
Step 1
Step 2
Step 3
Issue the halt command or init 0 command to instruct the Sun Netra T2000 to generate the OK prompt.
# haltOct 28 00:13:40 sh-netra-T2000 halt: halted by rootOct 28 00:13:41 sh-netra-T2000 syslogd: going down on signal 15SNMP Research DR-Web EMANATE Agent Version 16.1.0.44Copyright 1989-2005 SNMP Research, Inc.syncing file systems... doneProgram terminatedStep 4
ok boot cdrom -sSC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set|Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: /pci@7c0/pci@0/pci@1/pci@0/ide@8/cdrom@0,0:f File and args: -sSunOS Release 5.10 Version Generic_120011-14 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Booting to milestone "milestone/single-user:default".Configuring devices.Using RPC Bootparams for network configuration information.Attempting to configure interface e1000g3...Skipped interface e1000g3Attempting to configure interface e1000g2...Skipped interface e1000g2Attempting to configure interface e1000g1...Skipped interface e1000g1Attempting to configure interface e1000g0...Configured interface e1000g0Requesting System Maintenance ModeSINGLE USER MODE#Step 5
# raidctlController: 0Volume:c0t1d0Disk: 0.1.0Disk: 0.3.0Step 6
Note
# raidctl -d c0t1d0Deleting RAID volume c0t1d0 will destroy all data it contains; proceed (yes/no)? yes/pci@780/pci@0/pci@9/scsi@0 (mpt0):Volume 1 deleted./pci@780/pci@0/pci@9/scsi@0 (mpt0):Physical disk 0 deleted./pci@780/pci@0/pci@9/scsi@0 (mpt0):Physical disk 1 deleted.WARNING: /pci@780/pci@0/pci@9/scsi@0/sd@3,0 (sd5):Corrupt label; wrong magic numberVolume c0t1d0 is deleted successfully!Step 7
# raidctlController: 0Disk: 0.1.0Disk: 0.3.0Step 8
# init 0# syncing file systems... doneProgram terminatedOk
Note
Step 9
New Solaris 10 Installation
After you setup RAID 0 (optional) successfully, complete the following steps to install the Solaris 10 jumpstart image.
Step 1
Step 2
Step 3
# init 0Step 4
ok boot cdrom - installThe system displays text similar to the following:
SC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set\Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: /pci@7c0/pci@0/pci@1/pci@0/ide@8/cdrom@0,0:f File and args: - installSunOS Release 5.10 Version Generic_120011-14 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Configuring devices.Using RPC Bootparams for network configuration information.Attempting to configure interface e1000g3...Skipped interface e1000g3Attempting to configure interface e1000g2...Skipped interface e1000g2Attempting to configure interface e1000g1...Skipped interface e1000g1Attempting to configure interface e1000g0...Configured interface e1000g0Setting up Java. Please wait...Beginning system identification...Searching for configuration file(s)...Search complete.Discovering additional network configuration...Completing system identification...Starting remote procedure call (RPC) services: done.System identification complete.Starting Solaris installation program...Searching for JumpStart directory...<<< using cdrom install_config >>>Checking rules.ok file...Using profile: any_machineUsing finish script: any_finishExecuting JumpStart preinstall phase...Searching for SolStart directory...Checking rules.ok file...Using begin script: install_beginUsing finish script: patch_finishExecuting SolStart preinstall phase...Executing begin script "install_begin"...Begin script install_begin execution completed.Processing profile- Selecting cluster (SUNWCrnet)- Selecting package (SUNWadmfw)- Selecting package (SUNWcpc)- Selecting package (SUNWcpcu)- Selecting package (SUNWcstl)- Selecting package (SUNWless)- Selecting package (SUNWlucfg)- Selecting package (SUNWlur)- Selecting package (SUNWluu)- Selecting package (SUNWmkcd)- Selecting package (SUNWmipu)- Selecting package (SUNWmipr)- Selecting package (SUNWocf)- Selecting package (SUNWocfr)- Selecting package (SUNWspnego)- Selecting package (SUNWter)- Selecting package (SUNWtnfc)- Selecting package (SUNWucbt)- Selecting package (SUNWvld)- Selecting package (SUNWvldu)- Selecting package (SUNWzsh)- Selecting package (SUNWsacom)- Selecting package (SUNWxwdv)- Selecting package (SUNWctpls)- Selecting package (SUNWgssdh)- Selecting package (SUNWm64cf)- Selecting package (SUNWj5rt)- Selecting package (SUNWxwplt)- Selecting package (SUNWxwplr)- Selecting package (SUNWdtcor)- Selecting package (SUNWxwice)- Selecting package (SUNWxwrtl)- Selecting package (SUNWxwfnt)- Selecting package (SUNWlibC)- Selecting package (SUNWmfrun)- Selecting package (SUNWi15rf)- Selecting package (SUNWadmfr)- Selecting package (SUNWrsg)- Selecting package (SUNWsadmi)- Selecting package (SUNWsasnm)- Selecting package (SUNWmibii)- Selecting package (SUNWxi18n)- Selecting package (SUNWtoo)- Selecting package (SUNWsprot)- Selecting package (SUNWbip)- Selecting package (SUNWbind)- Selecting package (SUNWbindr)- Selecting package (SUNWgzip)- Selecting package (SUNWzip)- Selecting package (SUNWbash)- Selecting package (SUNWtcsh)- Selecting package (SUNWgss)- Selecting package (SUNWgssc)- Selecting package (SUNWgssk)- Selecting package (SUNWqos)- Selecting package (SUNWqosu)- Selecting package (SUNWmdb)- Selecting package (SUNWmdbr)- Selecting package (SUNWmdbdm)- Selecting package (SUNWnfsckr)- Selecting package (SUNWnfscr)- Selecting package (SUNWnfscu)- Selecting package (SUNWifp)- Selecting package (SUNWged)- Selecting package (SUNW1394)- Selecting package (SUNWqfed)- Selecting package (SUNWaccr)- Selecting package (SUNWaccu)- Selecting package (SUNWus)- Selecting package (SUNWrsgk)- Selecting package (SUNWzebrar)- Selecting package (SUNWzebrau)- Selecting package (SUNWeurf)- Selecting package (SUNWgcmn)- Selecting package (SUNWeuodf)- Selecting package (SUNWxwacx)- Selecting package (SUNWpoolr)- Selecting package (SUNWpool)- Selecting package (SUNWluzone)- Selecting package (SUNWzoner)- Selecting package (SUNWzoneu)- Selecting package (SUNWbtool)- Selecting package (SUNWdtrc)- Selecting package (SUNWdtrp)- Selecting package (SUNWfss)- Selecting package (SUNWinst)- Selecting package (SUNWipc)- Selecting package (SUNWqus)- Selecting package (SUNWqusu)- Selecting package (SUNWrcmdc)- Selecting package (SUNWdtdmr)- Selecting package (SUNWtltk)- Selecting package (SUNWtnetc)- Selecting package (SUNWtnfd)- Selecting package (SUNWtnetd)- Selecting package (SUNWtnetr)- Selecting package (SUNWsshcu)- Selecting package (SUNWsshdr)- Selecting package (SUNWsshdu)- Selecting package (SUNWsshr)- Selecting package (SUNWsshu)- Selecting package (SUNWatfsr)- Selecting package (SUNWatfsu)- Selecting package (SUNWrcmdr)- Selecting package (SUNWrcmds)- Selecting package (SUNWxcu4)- Selecting package (SUNWglmr)- Selecting package (SUNWi2cr)- Selecting package (SUNWpstl)- Selecting package (SUNWbart)- Selecting package (SUNWpiclu)- Selecting package (SUNWpiclr)- Selecting package (SUNWopensslr)- Selecting package (SUNWopenssl-commands)- Selecting all disks- Configuring boot device- Using disk (c0t1d0) for "rootdisk"- Configuring / (c0t1d0s0)- Configuring /var (c0t1d0s1)- Configuring swap (c0t1d0s3)- Configuring (c0t1d0s4)- Configuring (c0t1d0s6)- Configuring /opt (c0t1d0s5)Verifying disk configurationVerifying space allocation- Total software size: 396.45 MbytesPreparing system for Solaris installConfiguring disk (c0t1d0)- Creating Solaris disk label (VTOC)Creating and checking UFS file systems- Creating / (c0t1d0s0)- Creating /var (c0t1d0s1)- Creating /opt (c0t1d0s5)Beginning Solaris software installationStarting software installationSUNWlucfg........................done. 396.37 Mbytes remaining.SUNWcsu..........................done. 381.64 Mbytes remaining.SUNWcsr..........................done. 377.45 Mbytes remaining.SUNWcsl..........................done. 363.40 Mbytes remaining.SUNWcnetr........................done. 363.34 Mbytes remaining.SUNWkvmt200.v....................done. 363.16 Mbytes remaining.SUNWkvm.v........................done. 362.64 Mbytes remaining.SUNWcart200.v....................done. 362.55 Mbytes remaining.SUNWcar.v........................done. 362.46 Mbytes remaining.SUNWcakrnt2000.v.................done. 362.41 Mbytes remaining.SUNWcakr.v.......................done. 354.15 Mbytes remaining.SUNWckr..........................done. 342.16 Mbytes remaining.SUNWcsd..........................done. 341.89 Mbytes remaining.SUNWpr...........................done. 340.81 Mbytes remaining.SUNWtls..........................done. 332.14 Mbytes remaining.SUNWxwrtl........................done. 331.97 Mbytes remaining.SUNWxwice........................done. 331.69 Mbytes remaining.SUNWzlib.........................done. 331.32 Mbytes remaining.SUNWbzip.........................done. 331.05 Mbytes remaining.SUNWlibmsr.......................done. 327.77 Mbytes remaining.SUNWlibms........................done. 327.73 Mbytes remaining.SUNWxwfnt........................done. 316.02 Mbytes remaining.SUNWxwdv.........................done. 315.97 Mbytes remaining.SUNWxwplr........................done. 315.91 Mbytes remaining.SUNWperl584core..................done. 310.46 Mbytes remaining.SUNWperl584usr...................done. 289.32 Mbytes remaining.SUNWesu..........................done. 287.36 Mbytes remaining.SUNWcpp..........................done. 287.25 Mbytes remaining.SUNWdtcor........................done. 287.22 Mbytes remaining.SUNWxwplt........................done. 264.79 Mbytes remaining.SUNWlibC.........................done. 259.03 Mbytes remaining.SUNWctpls........................done. 258.95 Mbytes remaining.SUNWmfrun........................done. 248.86 Mbytes remaining.SUNWj5rt.........................done. 165.44 Mbytes remaining.SUNWlexpt........................done. 164.86 Mbytes remaining.SUNWlxml.........................done. 160.73 Mbytes remaining.SUNWkrbr.........................done. 160.64 Mbytes remaining.SUNWkrbu.........................done. 158.07 Mbytes remaining.SUNWgssc.........................done. 158.01 Mbytes remaining.SUNWgss..........................done. 157.63 Mbytes remaining.SUNWgcmn.........................done. 157.60 Mbytes remaining.SUNWdtdmr........................done. 157.49 Mbytes remaining.SUNWtltk.........................done. 154.43 Mbytes remaining.SUNWtnetc........................done. 154.26 Mbytes remaining.SUNWtnetd........................done. 154.17 Mbytes remaining.SUNWtnetr........................done. 154.12 Mbytes remaining.SUNWtnfc.........................done. 153.55 Mbytes remaining.SUNWtnfd.........................done. 153.46 Mbytes remaining.SUNWtoo..........................done. 152.34 Mbytes remaining.SUNWaudd.........................done. 151.67 Mbytes remaining.SUNWusb..........................done. 150.19 Mbytes remaining.SUNWusbs.........................done. 150.10 Mbytes remaining.SUNWuacm.........................done. 150.03 Mbytes remaining.SUNWucbt.........................done. 150.00 Mbytes remaining.SUNWudaplr.......................done. 149.98 Mbytes remaining.SUNWudaplu.......................done. 149.72 Mbytes remaining.SUNWib...........................done. 148.00 Mbytes remaining.SUNWipoib........................done. 147.86 Mbytes remaining.SUNWtavor........................done. 147.06 Mbytes remaining.SUNWudapltu......................done. 146.59 Mbytes remaining.SUNWudapltr......................done. 146.34 Mbytes remaining.SUNWuedg.........................done. 146.16 Mbytes remaining.SUNWugen.........................done. 146.09 Mbytes remaining.SUNWuksp.........................done. 145.99 Mbytes remaining.SUNWukspfw.......................done. 145.94 Mbytes remaining.SUNWopenssl-libraries............done. 138.92 Mbytes remaining.SUNWwbsup........................done. 138.56 Mbytes remaining.SUNWinstall-patch-utils-root.....done. 138.52 Mbytes remaining.SUNWpkgcmdsr.....................done. 138.48 Mbytes remaining.SUNWproduct-registry-root........done. 138.46 Mbytes remaining.SUNWwsr2.........................done. 138.12 Mbytes remaining.SUNWpkgcmdsu.....................done. 135.12 Mbytes remaining.SUNWswmt.........................done. 134.35 Mbytes remaining.SUNWuprl.........................done. 134.26 Mbytes remaining.SUNWgzip.........................done. 134.16 Mbytes remaining.SUNWocfr.........................done. 134.09 Mbytes remaining.SUNWocf..........................done. 133.51 Mbytes remaining.SUNWxi18n........................done. 132.51 Mbytes remaining.SUNWvld..........................done. 132.46 Mbytes remaining.SUNWxge..........................done. 131.87 Mbytes remaining.SUNWvldu.........................done. 131.81 Mbytes remaining.SUNWnfsckr.......................done. 130.38 Mbytes remaining.SUNWgssk.........................done. 130.13 Mbytes remaining.SUNWrsgk.........................done. 130.05 Mbytes remaining.SUNWnfscr........................done. 129.90 Mbytes remaining.SUNWnfscu........................done. 129.33 Mbytes remaining.SUNWeurf.........................done. 125.03 Mbytes remaining.SUNWi15rf........................done. 124.89 Mbytes remaining.SUNWmdr..........................done. 122.44 Mbytes remaining.SUNWmdu..........................done. 121.72 Mbytes remaining.SUNWadmc.........................done. 119.58 Mbytes remaining.SUNWadmfr........................done. 119.56 Mbytes remaining.SUNWadmfw........................done. 118.85 Mbytes remaining.SUNWadmlib-sysid.................done. 118.59 Mbytes remaining.SUNWadmr.........................done. 118.50 Mbytes remaining.SUNWadmap........................done. 117.57 Mbytes remaining.SUNWlur..........................done. 116.24 Mbytes remaining.SUNWluu..........................done. 115.00 Mbytes remaining.SUNWbip..........................done. 114.82 Mbytes remaining.SUNWrcmdc........................done. 113.92 Mbytes remaining.SUNWrcmds........................done. 113.62 Mbytes remaining.SUNWxwacx........................done. 113.44 Mbytes remaining.SUNWzfskr........................done. 112.51 Mbytes remaining.SUNWzfsr.........................done. 111.30 Mbytes remaining.SUNWsmapi........................done. 110.62 Mbytes remaining.SUNWzfsu.........................done. 108.96 Mbytes remaining.SUNWxcu4.........................done. 107.74 Mbytes remaining.SUNWsprot........................done. 106.22 Mbytes remaining.SUNWcslr.........................done. 89.74 Mbytes remaining.SUNWrsg..........................done. 89.61 Mbytes remaining.SUNWgssdh........................done. 89.29 Mbytes remaining.SUNWidnl.........................done. 88.73 Mbytes remaining.SUNWluxop........................done. 87.97 Mbytes remaining.SUNWses..........................done. 87.87 Mbytes remaining.SUNWssad.........................done. 87.54 Mbytes remaining.SUNWifp..........................done. 87.26 Mbytes remaining.SUNWinst.........................done. 86.77 Mbytes remaining.SUNWintgige......................done. 86.43 Mbytes remaining.SUNWipc..........................done. 86.38 Mbytes remaining.SUNWipfr.........................done. 86.31 Mbytes remaining.SUNWipfu.........................done. 85.03 Mbytes remaining.SUNWnisr.........................done. 84.89 Mbytes remaining.SUNWnisu.........................done. 82.52 Mbytes remaining.SUNWzebrar.......................done. 82.37 Mbytes remaining.SUNWzebrau.......................done. 77.22 Mbytes remaining.SUNWzip..........................done. 77.03 Mbytes remaining.SUNWzoner........................done. 76.97 Mbytes remaining.SUNWluzone.......................done. 76.82 Mbytes remaining.SUNWpoolr........................done. 76.76 Mbytes remaining.SUNWpool.........................done. 75.91 Mbytes remaining.SUNWtecla........................done. 75.28 Mbytes remaining.SUNWzoneu........................done. 74.26 Mbytes remaining.SUNWzsh..........................done. 71.13 Mbytes remaining.SUNWiscsir.......................done. 70.42 Mbytes remaining.SUNWiscsiu.......................done. 69.86 Mbytes remaining.SUNWloc..........................done. 69.35 Mbytes remaining.SUNWcpcu.........................done. 68.75 Mbytes remaining.SUNWfmdr.........................done. 68.69 Mbytes remaining.SUNWfmd..........................done. 63.22 Mbytes remaining.SUNWmdb..........................done. 57.60 Mbytes remaining.SUNWmdbr.........................done. 54.46 Mbytes remaining.SUNWpiclu........................done. 50.41 Mbytes remaining.SUNW1394.........................done. 49.63 Mbytes remaining.SUNWbash.........................done. 48.90 Mbytes remaining.SUNWaccr.........................done. 48.81 Mbytes remaining.SUNWaccu.........................done. 48.43 Mbytes remaining.SUNWced.v........................done. 47.76 Mbytes remaining.SUNWcpc.v........................done. 47.68 Mbytes remaining.SUNWiopc.v.......................done. 47.37 Mbytes remaining.SUNWbtool........................done. 46.02 Mbytes remaining.SUNWldomr.v......................done. 45.06 Mbytes remaining.SUNWldomu.v......................done. 44.94 Mbytes remaining.SUNWn2cp.v.......................done. 44.77 Mbytes remaining.SUNWniumx.v......................done. 44.71 Mbytes remaining.SUNWnxge.v.......................done. 43.99 Mbytes remaining.SUNWust1.v.......................done. 43.85 Mbytes remaining.SUNWust2.v.......................done. 43.74 Mbytes remaining.SUNWatfsr........................done. 43.67 Mbytes remaining.SUNWatfsu........................done. 43.38 Mbytes remaining.SUNWbart.........................done. 43.32 Mbytes remaining.SUNWbindr........................done. 43.25 Mbytes remaining.SUNWbind.........................done. 39.67 Mbytes remaining.SUNWdtrc.........................done. 34.37 Mbytes remaining.SUNWcfcl.........................done. 34.23 Mbytes remaining.SUNWcfclr........................done. 34.21 Mbytes remaining.SUNWcfpl.........................done. 33.83 Mbytes remaining.SUNWcfplr........................done. 33.78 Mbytes remaining.SUNWchxge........................done. 33.54 Mbytes remaining.SUNWjfca.........................done. 32.70 Mbytes remaining.SUNWjfcau........................done. 32.61 Mbytes remaining.SUNWcry..........................done. 30.98 Mbytes remaining.SUNWcryr.........................done. 30.54 Mbytes remaining.SUNWcstl.........................done. 30.39 Mbytes remaining.SUNWjss..........................done. 26.03 Mbytes remaining.SUNWkey..........................done. 25.62 Mbytes remaining.SUNWless.........................done. 25.45 Mbytes remaining.SUNWlibsasl......................done. 24.86 Mbytes remaining.SUNWlldap........................done. 24.66 Mbytes remaining.SUNWdtrp.........................done. 24.16 Mbytes remaining.SUNWluxopr.......................done. 23.48 Mbytes remaining.SUNWefcl.........................done. 22.78 Mbytes remaining.SUNWefcr.........................done. 22.73 Mbytes remaining.SUNWefcu.........................done. 22.68 Mbytes remaining.SUNWfctl.........................done. 22.22 Mbytes remaining.SUNWemlxs........................done. 18.07 Mbytes remaining.SUNWemlxu........................done. 17.29 Mbytes remaining.SUNWerid.........................done. 17.11 Mbytes remaining.SUNWeuodf........................done. 16.99 Mbytes remaining.SUNWm64cf........................done. 16.93 Mbytes remaining.SUNWfcprt........................done. 16.86 Mbytes remaining.SUNWmdbdm........................done. 16.81 Mbytes remaining.SUNWfchbar.......................done. 16.78 Mbytes remaining.SUNWfchba........................done. 15.19 Mbytes remaining.SUNWfcip.........................done. 14.99 Mbytes remaining.SUNWfcmdb........................done. 14.78 Mbytes remaining.SUNWfcp..........................done. 14.48 Mbytes remaining.SUNWmibii........................done. 14.35 Mbytes remaining.SUNWsasnm........................done. 13.47 Mbytes remaining.SUNWsadmi........................done. 12.47 Mbytes remaining.SUNWsacom........................done. 12.15 Mbytes remaining.SUNWmipr.........................done. 12.06 Mbytes remaining.SUNWmipu.........................done. 11.78 Mbytes remaining.SUNWmkcd.........................done. 10.48 Mbytes remaining.SUNWfcsm.........................done. 10.33 Mbytes remaining.SUNWfss..........................done. 10.22 Mbytes remaining.SUNWmpapir.......................done. 10.09 Mbytes remaining.SUNWmpapi........................done. 9.98 Mbytes remaining.SUNWmpathadm.....................done. 9.89 Mbytes remaining.SUNWmpathadmr....................done. 9.85 Mbytes remaining.SUNWmpsvplr......................done. 9.00 Mbytes remaining.SUNWged..........................done. 8.75 Mbytes remaining.SUNWopenssl-commands.............done. 8.37 Mbytes remaining.SUNWopensslr.....................done. 8.32 Mbytes remaining.SUNWpd...........................done. 7.61 Mbytes remaining.SUNWpiclr........................done. 7.58 Mbytes remaining.SUNWqos..........................done. 7.36 Mbytes remaining.SUNWqfed.........................done. 7.14 Mbytes remaining.SUNWqlc..........................done. 5.91 Mbytes remaining.SUNWqlcu.........................done. 5.85 Mbytes remaining.SUNWqosu.........................done. 5.73 Mbytes remaining.SUNWqus..........................done. 5.49 Mbytes remaining.SUNWqusu.........................done. 5.46 Mbytes remaining.SUNWrcmdr........................done. 5.38 Mbytes remaining.SUNWrge..........................done. 5.22 Mbytes remaining.SUNWroute........................done. 4.90 Mbytes remaining.SUNWrpcib........................done. 4.75 Mbytes remaining.SUNWsolnm........................done. 4.72 Mbytes remaining.SUNWspnego.......................done. 4.62 Mbytes remaining.SUNWsshcu........................done. 4.18 Mbytes remaining.SUNWsshdr........................done. 4.11 Mbytes remaining.SUNWsshdu........................done. 3.69 Mbytes remaining.SUNWsshr.........................done. 3.58 Mbytes remaining.SUNWsshu.........................done. 3.00 Mbytes remaining.SUNWtcsh.........................done. 2.62 Mbytes remaining.SUNWter..........................done. 1.00 Mbytes remaining.Completed software installationSolaris 10 software installation partially failedSolaris 10 packages partially installedSUNWxwfntCustomizing system files- Mount points table (/etc/vfstab)- Network host addresses (/etc/hosts)- Environment variables (/etc/default/init)Cleaning devicesCustomizing system devices- Physical devices (/devices)- Logical devices (/dev)Installing boot information- Installing boot blocks (c0t1d0s0)- Installing boot blocks (/dev/rdsk/c0t1d0s0)Installation log location- /a/var/sadm/system/logs/install_log (before reboot)- /var/sadm/system/logs/install_log (after reboot)Installation completeExecuting SolStart postinstall phase...Executing finish script "patch_finish"...Finish script patch_finish execution completed.Executing JumpStart postinstall phase...Executing finish script "any_finish"...any_finish started with SI_CONFIG_DIR = /tmp/install_configany_finish completedFinish script any_finish execution completed.The begin script log 'begin.log'is located in /var/sadm/system/logs after reboot.The finish script log 'finish.log'is located in /var/sadm/system/logs after reboot.syncing file systems... donerebooting...SC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set\Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: /pci@780/pci@0/pci@9/scsi@0/disk@1,0:a File and args:SunOS Release 5.10 Version Generic_120011-14 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Hostname: vtghostConfiguring devices.Loading smf(5) service descriptions: 40/108108/108/dev/rdsk/c0t1d0s5 is cleanCreating new rsa public/private host key pairCreating new dsa public/private host key pairvtghost console login: Oct 28 02:34:16 vtghost svc.startd[7]: application/cde-printinfo:default failed: transitioned to maintenance (see 'svcs -xv' for details)vtghost console login: rootPassword:Oct 28 02:36:24 vtghost login: ROOT LOGIN /dev/consoleSun Microsystems Inc. SunOS 5.10 Generic January 2005
Note
"Solaris 10 software installation partially failed"
"application/cde-printinfo:default failed"
Please ignore these messages as the software will be installed during installation of the Core-finish script.
Configuring Your Host
To configure your host, complete the following steps.
Step 1
Oct 28 02:36:24 vtghost login: ROOT LOGIN /dev/consoleSun Microsystems Inc. SunOS 5.10 Generic January 2005#Step 2
#WARNING##This program will unconfigure your system. It will cause it#to revert to a "blank" system - it will not have a name or know#about other systems or networks.##This program will also halt the system.##Do you want to continue (y/n) ?Step 3
The system displays text similar to the following:
svc.startd: The system is coming down. Please wait.svc.startd: 69 system services are now being stopped.Oct 28 02:52:18 vtghost syslogd: going down on signal 15svc.startd: The system is down.syncing file systems... doneProgram terminatedSC Alert: CRITICAL ALARM is setterminated{3} okStep 4
For Sparc-based platforms, enter the command boot and press Enter to reboot the system.
The system displays information similar to the following:
{8} ok bootSC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set|Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: /pci@780/pci@0/pci@9/scsi@0/disk@1,0:a File and args:SunOS Release 5.10 Version Generic_120011-14 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Hostname: unknownConfiguring devices./dev/rdsk/c0t1d0s5 is cleanStep 5
What type of terminal are you using?1) ANSI Standard CRT2) DEC VT523) DEC VT1004) Heathkit 195) Lear Siegler ADM316) PC Console7) Sun Command Tool8) Sun Workstation9) Televideo 91010) Televideo 92511) Wyse Model 5012) X Terminal Emulator (xterms)13) CDE Terminal Emulator (dtterm)14) OtherType the number of your choice and press Return:Enter the number that corresponds to the terminal you are using and press Enter. For example, if you are using an X terminal emulator, type 12 and press Enter.The system displays information similar to the following:Please specify the keyboard layout from the list below.> To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. keyboard Layout-------------------------^ [ ] Serbia-And-Montenegro| [ ] Slovenian| [ ] Slovakian| [ ] Spanish| [ ] Swedish| [ ] Swiss-French| [ ] Swiss-German| [ ] Taiwanese| [ ] TurkishQ| [ ] TurkishF| [ ] UK-English- [X] US-EnglishCreating new rsa public/private host key pairCreating new dsa public/private host key pairConfiguring network interface addresses: e1000g0 e1000g1 e1000g2 e1000g3.in.rdisc: No interfaces upText similar to the following is displayed:Network ConnectivitySpecify Yes if the system is connected to the network by one of the Solaris or vendor network/communication Ethernet cards that are supported on the Solaris CD. See your hardware documentation for the current list of supported cards. Specify No if the system is connected to a network/communication card that is not supported on the Solaris CD, and follow the instructions listed under Help.Networked---------[X] Yes[ ] No-------------------------------------------------------------------------------F2_Continue F6_HelpStep 6
The system displays text similar to the following:
Configure Multiple Network InterfacesMultiple network interfaces have been detected on this system. Specify all of the network interfaces you want to configure.Note: You must choose at least one interface to configure.Network interfaces------------------[ ] e1000g0[ ] e1000g1[ ] e1000g2[ ] e1000g3-------------------------------------------------------------------------------F2_Continue F6_Help
Note
Step 7
If you chose to configure a single interface, proceed to Step 9.
If you chose to configure multiple interfaces, proceed to Step 8.
Step 8
Primary Network InterfaceOn this screen you must specify which of the following network adapters is the system's primary network interface. Usually the correct choice is the lowest number. However, do not guess; ask your system administrator if you're not sure.> To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].Primary network interface-------------------------[X] e1000g0[ ] e1000g1[ ] e1000g2----------------------------------------------------Esc-2_Continue Esc-6_HelpSelect your primary network interface and press Esc-2 to continue.Step 9
DHCP for e1000g0Specify whether or not this network interface should use DHCP to configure itself. Choose Yes if DHCP is to be used, or No if the network interface is to be configured manually.NOTE: DHCP support will not be enabled, if selected, until after the system reboots.Use DHCP for e1000g0--------------------[ ] Yes[X] No-------------------------------------------------------------------------------Esc-2_Continue Esc-6_HelpStep 10
The system displays text similar to the following:
Host Name for e1000g0Enter the host name which identifies this system on the network. The name must be unique within your domain; creating a duplicate host name will cause problems on the network after you install Solaris.A host name must have at least one character; it can contain letters, digits, and minus signs (-).Host name for e1000g0-------------------------------------------------------------------------------Esc-2_Continue Esc-6_Help
Caution
Step 11
The system displays text similar to the following:
IP Address for e1000g0Enter the Internet Protocol (IP) address for this network interface.It must be unique and follow your site's address conventions, or a system/network failure could result. IP addresses contain four sets of numbers separated by periods (for example 129.200.9.1).IP address for e1000g0IP address:--------------------------------------------------------------------------------Esc-2_Continue Esc-6_HelpStep 12
The system displays text similar to the following:
Subnet for e1000g0On this screen you must specify whether this system is part of a subnet. If you specify incorrectly, the system will have problems communicating on the network after you reboot. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. System part of a subnet-----------------------[X] Yes[ ] No-------------------------------------------------------------------------------Esc-2_Continue Esc-6_HelpNote If you need to modify your IP addresses after you have installed Sun Solaris 10, there are three files you need to update, instead of the two files required in previous releases of Sun Solaris operating system software. The following files must be edited to in order to modify the IP address for an interface:/etc/inet/hosts/etc/hostname.inf_name/etc/inet/ipnodesWhere inf_name is the name of the interface, such as e1000g0.Step 13
The system displays text similar to the following:
Netmask for e1000g0On this screen you must specify the netmask of your subnet.A default netmask is shown; do not accept the default unless you are sure it is correct for your subnet. A netmask must contain four sets of numbers separated by periods (for example 255.255.255.0).Netmask for e1000g0 255.255.255.0----------------------------------------------------------------------------------Esc-2_Continue Esc-6_HelpStep 14
The system displays text similar to the following:
IPv6 for e1000g0Specify whether or not you want to enable IPv6, the next generation Internet Protocol, on this network interface. Enabling IPv6 will have no effect if this machine is not on a network that provides IPv6 service. IPv4 service will not be affected if IPv6 is enabled. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Enable IPv6 for e1000g0-----------------------[ ] Yes[X] No-------------------------------------------------------------------------------Esc-2_Continue Esc-6_Help
Note
Step 15
Text similar to the following is displayed:
Set the Default Route for e1000g0 To specify the default route, you can let the software try to detect one upon reboot, you can specify the IP address of the router, or you can choose None. Choose None if you do not have a router on your subnet. > To make a selection, use the arrow keys to select your choice and press Return to mark it [X]. Default Route for e1000g0--------------------------[X] Detect one upon reboot[ ] Specify one[ ] None-------------------------------------------------------------------------------Esc-2_Continue Esc-6_HelpStep 16
Text similar to the following is displayed.
Default Route IP Address for e1000g0 Enter the IP address of the default route. This entry will be placed in the /etc/defaultrouter file and will be the default route after you reboot (example 129.146.89.225).Router IP Address for e1000g0-------------------------------------------------------------------------------Esc-2_Continue Esc-6_HelpStep 17
Text similar to the following is displayed:
Confirm Information for e1000g0 > Confirm the following information. If it is correct, press F2; to change any information, press F4.Primary network interface: e1000g0Secondary network interfaces: e1000g1, e1000g2System part of a subnet: YesNetmask: 255.255.255.224Enable IPv6: NoDefault Route: Specify oneRouter IP Address: 10.74.49.1Esc-2_Continue Esc-4_Change Esc-6_HelpStep 18
Note
If you chose to configure a single interface, proceed to Step 20.
If you chose to configure multiple interfaces, proceed to Step 19.
Step 19
Step 20
Configure Security Policy:Specify Yes if the system will use the Kerberos security mechanism. Specify No if this system will use standard UNIX security.Configure Kerberos Security---------------------------[ ] Yes[X] NoEsc-2_Continue Esc-4_Change Esc-6_HelpStep 21
Text similar to the following is displayed:
Confirm Information> Confirm the following information. If it is correct, press F2; to change any information, press F4.--------------------------------------------------------------------------------Esc-2_Continue Esc-4_Change Esc-6_HelpStep 22
Text similar to the following is displayed:
Name ServiceOn this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].Name service------------[X] NIS+[ ] NIS[ ] DNS[ ] LDAP[ ] None------------------------------------------------------------------ Esc-2_Continue Esc-6_HelpStep 23
Text similar to the following is displayed:
Confirm Information > Confirm the following information. If it is correct, press F2; to change any information, press F4.Name service: NoneEsc-2_Continue Esc-4_Change Esc-6_HelpStep 24
Text similar to the following is displayed:
NFSv4 Domain NameNFS version 4 uses a domain name that is automatically derived from the system's naming services. The derived domain name is sufficient for most configurations. In a few cases, mounts that cross domain boundaries might cause files to appear to be owned by "nobody" due to the lack of a common domain name. The current NFSv4 default domain is: ""NFSv4 Domain Configuration----------------------------------------------[X] Use the NFSv4 domain derived by the system[ ] Specify a different NFSv4 domainEsc-2_Continue Esc-6_HelpStep 25
Text similar to the following is displayed.
Confirm Information for NFSv4 Domain > Confirm the following information. If it is correct, press F2; to change any information, press F4.-------------------------------------------------------------------------Esc-2_Continue Esc-4_Change Esc-6_HelpStep 26
Text similar to the following is displayed:
Time Zone On this screen you must specify your default time zone. You can specify a time zone in three ways: select one of the continents or oceans from the list, select other - offset from GMT, or other - specify time zone file. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].Continents and Oceans----------------------------------- [ ] Africa| [ ] Americas| [ ] Antarctica| [ ] Arctic Ocean| [ ] Asia| [ ] Atlantic Ocean| [ ] Australia| [ ] Europe| [ ] Indian Oceanv [ ] Pacific Ocean------------------------------------------------------------------------- Esc-2_Continue Esc-6_HelpStep 27
Note
a.
Text similar to the following is displayed.
Country or Region > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Countries and Regions------------------------- [ ] United States| [ ] Anguilla| [ ] Antigua & Barbuda| [ ] Argentina| [ ] Aruba| [ ] Bahamas| [ ] Barbados| [ ] Belize| [ ] Bolivia| [ ] Brazil| [ ] Canada| [ ] Cayman Islands| [ ] Chilev [ ] Colombia-------------------------------------------------------------------- Esc-2_Continue Esc-6_Helpb.
Text similar to the following is displayed:
Time Zone > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Time zones --------------------------------------------------------------------------- [ ] Eastern Time| [ ] Eastern Time - Michigan - most locations| [ ] Eastern Time - Kentucky - Louisville area| [ ] Eastern Time - Kentucky - Wayne County| [ ] Eastern Time - Indiana - most locations| [ ] Eastern Time - Indiana - Starke County| [ ] Eastern Time - Indiana - Pulaski County| [ ] Eastern Time - Indiana - Crawford County| [ ] Eastern Time - Indiana - Switzerland County| [ ] Central Time| [ ] Central Time - Indiana - Daviess, Dubois, Knox, Martin & Perry Count| [ ] Central Time - Indiana - Pike County| [ ] Central Time - Michigan - Dickinson, Gogebic, Iron & Menominee Countv [ ] Central Time - North Dakota - Oliver County---------------------------------------------------------------------------------------Esc-2_Continue Esc-6_Helpc.
Text similar to the following is displayed:
Date and Time> Accept the default date and time or enter new values.Date and time: 2008-10-28 04:40Year (4 digits) : 2008Month (1-12) : 10Day (1-31) : 28Hour (0-23) : 04Minute (0-59) : 40Esc-2_Continue Esc-6_HelpStep 28
Text similar to the following is displayed:
Confirm Information > Confirm the following information. If it is correct, press F2; to change any information, press F4. Time zone: Eastern Time(US/Eastern)Date and time: 2008-10-28 04:40:00Esc-2_Continue Esc-4_Change Esc-6_HelpStep 29
Text similar to the following is displayed:
Root PasswordPlease enter the root password for this system. The root password may contain alphanumeric and special characters. For security, the password will not be displayed on the screen as you type it.> If you do not want a root password, leave both entries blank. Root password:Root password:--------------------------------------------------Esc-2_Continue Esc-6_HelpStep 30
Text similar to the following might be displayed:
System identification is completed.rebooting system due to change(s) in /etc/default/initsyncing file systems... donerebooting...SC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set/Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: /pci@780/pci@0/pci@9/scsi@0/disk@1,0:a File and args:SunOS Release 5.10 Version Generic_120011-14 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Hostname: sh-netra-T2000/dev/rdsk/c0t1d0s5 is cleansh-netra-T2000 console login: Oct 28 04:42:45 sh-netra-T2000 svc.startd[7]: application/cde-printinfo:default failed: transitioned to maintenance (see 'svcs -xv' for details)sh-netra-T2000 console login:Step 31
a.
–
–
–
b.
Caution
Platform-Specific Installation Procedure
Complete the following steps to install files specific to your Cisco platform:
Step 1
Step 2
Step 3
mount -F hsfs -o ro /dev/dsk/devname /cdrom For example mount -F hsfs -o ro /dev/dsk/c1t0d0s0 /cdrom
Note
Step 4
For Sparc-based platforms:
./cdrom/core_finish/core_finish.shStep 5
Note
sh-netra-T2000 is the hostname of this box; enter hostname that applies to your specific case
Text similar to the following is displayed:
CORE CD installation finishing procedure startedPlease enter this host node name:sh-netra-T2000Re-enter this host node name:sh-netra-T2000Using 'sh-netra-T2000' for this hostStart installation of core extra packagesProcessing package instance <SUNWxwfnt> from </cdrom/Solaris_10/Product>X Window System platform required fonts(sparc) 6.6.2.7400,REV=0.2004.12.15This appears to be an attempt to install the same architecture andversion of a package which is already installed. This installationwill attempt to overwrite this package.Copyright 2005 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Using </usr> as the package base directory.## Processing package information.## Processing system information.366 package pathnames are already properly installed.Installing X Window System platform required fonts as <SUNWxwfnt>## Installing part 1 of 1.[ verifying class <fontsdir> ][ verifying class <fontsalias> ][ verifying class <encodingsdir> ][ verifying class <ttmapsdir> ]Installation of <SUNWxwfnt> was successful.Adding <SUNWvts>Processing package instance <SUNWvts> from </opt/xtrapkgs>SunVTS Framework(sparc) 7.0,REV=2007.11.22.17.02## Executing checkinstall script.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Using </usr> as the package base directory.## Processing package information.## Processing system information.Installing SunVTS Framework as <SUNWvts>## Installing part 1 of 1.11804 blocksInstallation of <SUNWvts> was successful.Adding <SUNWvtsr>Processing package instance <SUNWvtsr> from </opt/xtrapkgs>SunVTS Framework (Root)(sparc) 7.0,REV=2007.11.22.17.02Using </> as the package base directory.## Processing package information.## Processing system information.1 package pathname is already properly installed.Installing SunVTS Framework (Root) as <SUNWvtsr>## Installing part 1 of 1.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.6 blocksInstallation of <SUNWvtsr> was successful.Adding <SUNWvtsts>Processing package instance <SUNWvtsts> from </opt/xtrapkgs>SunVTS Core Installation Tests(sparc) 7.0,REV=2007.11.22.17.02## Executing checkinstall script.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Using </usr> as the package base directory.## Processing package information.## Processing system information.11 package pathnames are already properly installed.Installing SunVTS Core Installation Tests as <SUNWvtsts>## Installing part 1 of 1.97583 blocksInstallation of <SUNWvtsts> was successful.Adding <SUNWexplo>Processing package instance <SUNWexplo> from </opt/xtrapkgs>Sun(TM) Explorer Data Collector(all) 5.10,REV=2007.09.20.19.12## Executing checkinstall script.Copyright 1996-2007 Sun Microsystems, Inc.All rights reserved.Using </opt> as the package base directory.## Processing package information.## Processing system information.Installing Sun(TM) Explorer Data Collector as <SUNWexplo>## Executing preinstall script.## Installing part 1 of 1./opt/SUNWexplo/LICENSEREADME/LICENSE.txt/opt/SUNWexplo/LICENSEREADME/THIRDPARTYLICENSEREADME.txt/opt/SUNWexplo/bin/capture.sparc/opt/SUNWexplo/bin/core_check.sh/opt/SUNWexplo/bin/curl.i386/opt/SUNWexplo/bin/curl.sparc/opt/SUNWexplo/bin/diskinfo.i386/opt/SUNWexplo/bin/diskinfo.sparc/opt/SUNWexplo/bin/exp_defaults/opt/SUNWexplo/bin/explorer/opt/SUNWexplo/bin/explorer_notify_update/opt/SUNWexplo/bin/instinfo_config/opt/SUNWexplo/bin/j2se_config/opt/SUNWexplo/bin/mktime.i386/opt/SUNWexplo/bin/mktime.sparc/opt/SUNWexplo/bin/rprtfru.sparc/opt/SUNWexplo/bin/se3kxtr.ksh/opt/SUNWexplo/bin/snapshot/opt/SUNWexplo/bin/st_diag.i386/opt/SUNWexplo/bin/st_diag.sparc/opt/SUNWexplo/bin/sunone_config/opt/SUNWexplo/bin/sunone_ps/opt/SUNWexplo/doc/CHANGES/opt/SUNWexplo/doc/README/opt/SUNWexplo/doc/README.j2se_config/opt/SUNWexplo/doc/README.man/opt/SUNWexplo/doc/README.sunone_config/opt/SUNWexplo/java/fruid-scappclient.jar/opt/SUNWexplo/java/libfru.jar/opt/SUNWexplo/lib/AMERICAS_countries.1/opt/SUNWexplo/lib/AMERICAS_countries.2/opt/SUNWexplo/lib/AMERICAS_countries.3/opt/SUNWexplo/lib/AMERICAS_countries_codes/opt/SUNWexplo/lib/APAC_countries.1/opt/SUNWexplo/lib/APAC_countries.2/opt/SUNWexplo/lib/APAC_countries.3/opt/SUNWexplo/lib/APAC_countries.4/opt/SUNWexplo/lib/APAC_countries_codes/opt/SUNWexplo/lib/EMEA_countries.1/opt/SUNWexplo/lib/EMEA_countries.2/opt/SUNWexplo/lib/EMEA_countries.3/opt/SUNWexplo/lib/EMEA_countries.4/opt/SUNWexplo/lib/EMEA_countries.5/opt/SUNWexplo/lib/EMEA_countries.6/opt/SUNWexplo/lib/EMEA_countries.7/opt/SUNWexplo/lib/EMEA_countries.8/opt/SUNWexplo/lib/EMEA_countries_codes/opt/SUNWexplo/lib/ca-bundle.crt/opt/SUNWexplo/lib/crontab.txt/opt/SUNWexplo/lib/exp_check/opt/SUNWexplo/lib/exp_common/opt/SUNWexplo/lib/exp_file/opt/SUNWexplo/lib/exp_ftp/opt/SUNWexplo/lib/exp_https/opt/SUNWexplo/lib/exp_j2se/opt/SUNWexplo/lib/exp_mail/opt/SUNWexplo/lib/exp_main/opt/SUNWexplo/lib/exp_postproc/opt/SUNWexplo/lib/exp_sunone/opt/SUNWexplo/lib/exp_tools/opt/SUNWexplo/lib/exp_transport/opt/SUNWexplo/lib/libfru.so <symbolic link>/opt/SUNWexplo/lib/libfru.so.1/opt/SUNWexplo/lib/libfrujni.so <symbolic link>/opt/SUNWexplo/lib/libfrujni.so.1/opt/SUNWexplo/lib/libfrureg.so <symbolic link>/opt/SUNWexplo/lib/libfrureg.so.1/opt/SUNWexplo/lib/libfrurmi.so <symbolic link>/opt/SUNWexplo/lib/libfrurmi.so.1/opt/SUNWexplo/lib/libfruutils.so <symbolic link>/opt/SUNWexplo/lib/libfruutils.so.1/opt/SUNWexplo/lib/locale/C/LC_MESSAGES/explorer.mo/opt/SUNWexplo/lib/locale/C/LC_MESSAGES/explorer.po/opt/SUNWexplo/lib/snapshot.conf/opt/SUNWexplo/lib/uu2b64/opt/SUNWexplo/man/man1m/explorer.1m/opt/SUNWexplo/man/man4/explorer.4/opt/SUNWexplo/man/man5/explorer.5/opt/SUNWexplo/tools/1280extended/opt/SUNWexplo/tools/Tx000/opt/SUNWexplo/tools/alomextended/opt/SUNWexplo/tools/b1600extended/opt/SUNWexplo/tools/b1600switch/opt/SUNWexplo/tools/cluster/opt/SUNWexplo/tools/cmdline/opt/SUNWexplo/tools/crypto/opt/SUNWexplo/tools/cst/opt/SUNWexplo/tools/disks/opt/SUNWexplo/tools/emc/opt/SUNWexplo/tools/etc/opt/SUNWexplo/tools/fcal/opt/SUNWexplo/tools/firelink/opt/SUNWexplo/tools/fma/opt/SUNWexplo/tools/fru/opt/SUNWexplo/tools/hds/opt/SUNWexplo/tools/ilomextended/opt/SUNWexplo/tools/indy/opt/SUNWexplo/tools/init/opt/SUNWexplo/tools/instinfo/opt/SUNWexplo/tools/iplanet <symbolic link>/opt/SUNWexplo/tools/ipmi/opt/SUNWexplo/tools/ipmiextended/opt/SUNWexplo/tools/j2se/opt/SUNWexplo/tools/ldap/opt/SUNWexplo/tools/lic/opt/SUNWexplo/tools/lp/opt/SUNWexplo/tools/lvm/opt/SUNWexplo/tools/messages/opt/SUNWexplo/tools/nbu/opt/SUNWexplo/tools/nbu_extended/opt/SUNWexplo/tools/ndd/opt/SUNWexplo/tools/netconnect/opt/SUNWexplo/tools/netinfo/opt/SUNWexplo/tools/nhas/opt/SUNWexplo/tools/patch/opt/SUNWexplo/tools/pci/opt/SUNWexplo/tools/photon/opt/SUNWexplo/tools/pkg/opt/SUNWexplo/tools/proc/opt/SUNWexplo/tools/quorumserv/opt/SUNWexplo/tools/samfs/opt/SUNWexplo/tools/sanextended/opt/SUNWexplo/tools/sap/opt/SUNWexplo/tools/sbu/opt/SUNWexplo/tools/scextended/opt/SUNWexplo/tools/se3k/opt/SUNWexplo/tools/se3kextended/opt/SUNWexplo/tools/se61xx/opt/SUNWexplo/tools/se6320/opt/SUNWexplo/tools/se6920/opt/SUNWexplo/tools/sf15k_ndd/opt/SUNWexplo/tools/sf15k_sc/opt/SUNWexplo/tools/smfextended/opt/SUNWexplo/tools/sonoma/opt/SUNWexplo/tools/srscextended/opt/SUNWexplo/tools/ssa/opt/SUNWexplo/tools/ssp/opt/SUNWexplo/tools/st25xx/opt/SUNWexplo/tools/storade/opt/SUNWexplo/tools/storedge/opt/SUNWexplo/tools/stortools/opt/SUNWexplo/tools/sunjes/opt/SUNWexplo/tools/sunone/opt/SUNWexplo/tools/sunray/opt/SUNWexplo/tools/sysconfig/opt/SUNWexplo/tools/syslogs/opt/SUNWexplo/tools/t3/opt/SUNWexplo/tools/t3extended/opt/SUNWexplo/tools/tape/opt/SUNWexplo/tools/test/opt/SUNWexplo/tools/u4ft/opt/SUNWexplo/tools/ufsextended/opt/SUNWexplo/tools/var/opt/SUNWexplo/tools/vtsst/opt/SUNWexplo/tools/vxfs/opt/SUNWexplo/tools/vxvm/opt/SUNWexplo/tools/xscfextended[ verifying class <none> ]## Executing postinstall script./usr/bin/catman is not available for usePlease run: catman -w -M /opt/SUNWexplo/man manuallyInstallation of <SUNWexplo> was successful.Adding <SUNWexplu>Processing package instance <SUNWexplu> from </opt/xtrapkgs>Sun(TM) Explorer Data Collector Config Files(all) 5.10,REV=2007.09.20.19.12## Executing checkinstall script.Copyright 1996-2007 Sun Microsystems, Inc.All rights reserved.Using </> as the package base directory.## Processing package information.## Processing system information.2 package pathnames are already properly installed.Installing Sun(TM) Explorer Data Collector Config Files as <SUNWexplu>## Installing part 1 of 1./etc/opt/SUNWexplo/LICENSEREADME/LICENSE.txt/etc/opt/SUNWexplo/t3files.txt[ verifying class <none> ]Modifying /etc/opt/SUNWexplo/1280input.txtModifying /etc/opt/SUNWexplo/alominput.txtModifying /etc/opt/SUNWexplo/b1600input.txtModifying /etc/opt/SUNWexplo/b1600switchinput.txtModifying /etc/opt/SUNWexplo/ilominput.txtModifying /etc/opt/SUNWexplo/indyinput.txtModifying /etc/opt/SUNWexplo/ipmiinput.txtModifying /etc/opt/SUNWexplo/saninput.txtModifying /etc/opt/SUNWexplo/scinput.txtModifying /etc/opt/SUNWexplo/se3kinput.txtModifying /etc/opt/SUNWexplo/se6320input.txtModifying /etc/opt/SUNWexplo/se6920input.txtModifying /etc/opt/SUNWexplo/srscinput.txtModifying /etc/opt/SUNWexplo/t3input.txtModifying /etc/opt/SUNWexplo/tapeinput.txtModifying /etc/opt/SUNWexplo/xscfinput.txt[ verifying class <build> ]## Executing postinstall script.Installation of <SUNWexplu> was successful.Adding <SUNWpsr>Processing package instance <SUNWpsr> from </opt/xtrapkgs>Solaris Print - LP Server, (root)(sparc) 13.1,REV=2005.01.21.15.53Using </> as the package base directory.## Processing package information.## Processing system information.11 package pathnames are already properly installed.Installing Solaris Print - LP Server, (root) as <SUNWpsr>## Executing preinstall script.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.## Installing part 1 of 1.19 blocks[ verifying class <renameold> ][ verifying class <preserve> ][ verifying class <manifest> ]## Executing postinstall script.Installation of <SUNWpsr> was successful.Adding <SUNWpcr>Processing package instance <SUNWpcr> from </opt/xtrapkgs>Solaris Print - Client, (root)(sparc) 13.1,REV=2005.01.21.15.53Using </> as the package base directory.## Processing package information.## Processing system information.10 package pathnames are already properly installed.Installing Solaris Print - Client, (root) as <SUNWpcr>## Installing part 1 of 1.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.2 blocks[ verifying class <preserve> ][ verifying class <manifest> ]## Executing postinstall script.Installation of <SUNWpcr> was successful.Adding <SUNWpcu>Processing package instance <SUNWpcu> from </opt/xtrapkgs>Solaris Print - Client, (usr)(sparc) 13.1,REV=2005.01.21.15.53Using </> as the package base directory.## Processing package information.## Processing system information.4 package pathnames are already properly installed.Installing Solaris Print - Client, (usr) as <SUNWpcu>## Installing part 1 of 1.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.545 blocksInstallation of <SUNWpcu> was successful.Adding <SUNWpsu>Processing package instance <SUNWpsu> from </opt/xtrapkgs>Solaris Print - LP Server, (usr)(sparc) 13.1,REV=2005.01.21.15.53Using </> as the package base directory.## Processing package information.## Processing system information.12 package pathnames are already properly installed.Installing Solaris Print - LP Server, (usr) as <SUNWpsu>## Installing part 1 of 1.Copyright 2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.3157 blocksInstallation of <SUNWpsu> was successful.Adding <SMCsudo>Processing package instance <SMCsudo> from </opt/xtrapkgs>sudo(sparc) 1.6.9p12Todd Miller et alUsing </usr/local> as the package base directory.## Processing package information.## Processing system information.2 package pathnames are already properly installed.Installing sudo as <SMCsudo>## Installing part 1 of 1./usr/local/bin/sudo/usr/local/bin/sudoedit/usr/local/doc/sudo/BUGS/usr/local/doc/sudo/CHANGES/usr/local/doc/sudo/HISTORY/usr/local/doc/sudo/INSTALL/usr/local/doc/sudo/INSTALL.configure/usr/local/doc/sudo/LICENSE/usr/local/doc/sudo/PORTING/usr/local/doc/sudo/README/usr/local/doc/sudo/README.LDAP/usr/local/doc/sudo/TROUBLESHOOTING/usr/local/doc/sudo/UPGRADE/usr/local/etc/sudoers/usr/local/libexec/sudo_noexec.la/usr/local/libexec/sudo_noexec.so/usr/local/man/man1m/sudo.1m/usr/local/man/man1m/sudoedit.1m/usr/local/man/man1m/visudo.1m/usr/local/man/man4/sudoers.4/usr/local/sbin/visudo[ verifying class <none> ]Installation of <SMCsudo> was successful.Adding <SMClsof>Processing package instance <SMClsof> from </opt/xtrapkgs>lsof(sparc) 4.77Vic AbellUsing </usr/local> as the package base directory.## Processing package information.## Processing system information.3 package pathnames are already properly installed.Installing lsof as <SMClsof>## Installing part 1 of 1./usr/local/bin/lsof/usr/local/bin/sparcv7/lsof/usr/local/bin/sparcv9/lsof/usr/local/doc/lsof/00.README.FIRST <attribute change only>/usr/local/doc/lsof/00CREDITS/usr/local/doc/lsof/00DCACHE/usr/local/doc/lsof/00DIALECTS/usr/local/doc/lsof/00DIST/usr/local/doc/lsof/00FAQ/usr/local/doc/lsof/00LSOF-L/usr/local/doc/lsof/00MANIFEST/usr/local/doc/lsof/00PORTING/usr/local/doc/lsof/00QUICKSTART/usr/local/doc/lsof/00README/usr/local/doc/lsof/00TEST/usr/local/doc/lsof/00XCONFIG/usr/local/doc/lsof/lsof.man/usr/local/man/man8/lsof.8[ verifying class <none> ]Installation of <SMClsof> was successful.SUNW,Netra-T2000SUNW,Netra-T2000 needs LOM packagesspawn pkgadd -d . SUNWlomrProcessing package instance <SUNWlomr> from </opt/lompkgs>LOMlite driver (root)(sparc) 2.0,REV=2000.08.22.14.14Copyright 2000 Sun Microsystems, Inc. All rights reserved.## Executing checkinstall script.Using </> as the package base directory.## Processing package information.## Processing system information.7 package pathnames are already properly installed.## Verifying package dependencies.## Verifying disk space requirements.## Checking for conflicts with packages already installed.## Checking for setuid/setgid programs.This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <SUNWlomr> [y,n,?] yInstalling LOMlite driver (root) as <SUNWlomr>## Installing part 1 of 1.20 blocksi.drivers (INFO): Startingi.drivers (INFO): Installing /opt/lompkgs/SUNWlomr/reloc/platform/sun4u/kernel/drv/lomi.drivers (INFO): Installing /opt/lompkgs/SUNWlomr/reloc/platform/sun4u/kernel/drv/lompi.drivers (INFO): Installing /opt/lompkgs/SUNWlomr/reloc/platform/sun4u/kernel/drv/sparcv9/lomi.drivers (INFO): Installing /opt/lompkgs/SUNWlomr/reloc/platform/sun4u/kernel/drv/sparcv9/lompi.drivers (INFO): Installing /opt/lompkgs/SUNWlomr/reloc/platform/sun4u/kernel/drv/sparcv9/lomvi.drivers (INFO): Identified drivers 'lom lomp lomv'i.drivers (INFO): Cleaning up old driver 'lom'...i.drivers (INFO): Cleaning up old driver 'lomp'...i.drivers (INFO): Cleaning up old driver 'lomv'...i.drivers (INFO): Cleaning up old driver 'lomh'...i.drivers (INFO): Adding driver 'lomp'...driver = 'lomp'aliases = ''link = 'lomp'spec = 'lomp'Adding devlink entry 'type=ddi_pseudo;name=lomp lomp'adding driver with aliases '' perm '* 0644 root sys'Cannot find module (lomp).i.drivers (ERROR): Failed to add driver, status 1i.drivers (INFO): Adding driver 'lomv'...driver = 'lomv'aliases = 'SUNW,lomv'link = 'SUNW,lomv lomv'spec = '\M0'Adding devlink entry 'type=ddi_pseudo;name=SUNW,lomv \M0'Adding devlink entry 'type=ddi_pseudo;name=lomv \M0'adding driver with aliases 'SUNW,lomv' perm '* 0644 root sys'Cannot find module (lomv).i.drivers (ERROR): Failed to add driver, status 1i.drivers (INFO): Adding driver 'lom'...driver = 'lom'aliases = 'SUNW,lomh SUNW,lom'link = 'SUNW,lomh SUNW,lom'spec = 'lom'Adding devlink entry 'type=ddi_pseudo;name=SUNW,lomh lom'Adding devlink entry 'type=ddi_pseudo;name=SUNW,lom lom'adding driver with aliases 'SUNW,lomh SUNW,lom' perm '* 0644 root sys'Cannot find module (lom).i.drivers (ERROR): Failed to add driver, status 1i.drivers (ERROR): Failed with status 1pkgadd: ERROR: class action script did not complete successfullyInstallation of <SUNWlomr> failed.spawn pkgadd -d . SUNWlomuProcessing package instance <SUNWlomu> from </opt/lompkgs>LOMlite Utilities (usr)(sparc) 2.0,REV=2000.08.22.14.14Copyright 2000 Sun Microsystems, Inc. All rights reserved.Using </> as the package base directory.## Processing package information.## Processing system information.4 package pathnames are already properly installed.## Verifying package dependencies.WARNING:The <SUNWlomr> package "LOMlite driver (root)" is aprerequisite package and is not completely installed.Do you want to continue with the installation of <SUNWlomu> [y,n,?] y## Verifying disk space requirements.## Checking for conflicts with packages already installed.## Checking for setuid/setgid programs.Installing LOMlite Utilities (usr) as <SUNWlomu>## Installing part 1 of 1.2333 blocksInstallation of <SUNWlomu> was successful.Validating patches...Loading patches installed on the system...Done!Loading patches requested to install.Done!The following requested patches have packages not installed on the systemPackage SUNWlomm from directory SUNWlomm in patch 110208-22 is not installed on the system. Changes for package SUNWlomm will not be applied to the system.Package SUNWclomu from directory SUNWclomu in patch 110208-22 is not installed on the system. Changes for package SUNWclomu will not be applied to the system.Package SUNWdlomu from directory SUNWdlomu in patch 110208-22 is not installed on the system. Changes for package SUNWdlomu will not be applied to the system.Package SUNWelomu from directory SUNWelomu in patch 110208-22 is not installed on the system. Changes for package SUNWelomu will not be applied to the system.Package SUNWflomu from directory SUNWflomu in patch 110208-22 is not installed on the system. Changes for package SUNWflomu will not be applied to the system.Package SUNWhlomu from directory SUNWhlomu in patch 110208-22 is not installed on the system. Changes for package SUNWhlomu will not be applied to the system.Package SUNWilomu from directory SUNWilomu in patch 110208-22 is not installed on the system. Changes for package SUNWilomu will not be applied to the system.Package SUNWjlomu from directory SUNWjlomu in patch 110208-22 is not installed on the system. Changes for package SUNWjlomu will not be applied to the system.Package SUNWklomu from directory SUNWklomu in patch 110208-22 is not installed on the system. Changes for package SUNWklomu will not be applied to the system.Package SUNWslomu from directory SUNWslomu in patch 110208-22 is not installed on the system. Changes for package SUNWslomu will not be applied to the system.Checking patches that you specified for installation.Done!Approved patches will be installed in this order:110208-22Checking installed patches...Verifying sufficient filesystem capacity (dry run method)...Installing patch packages...Patch 110208-22 has been successfully installed.See /var/sadm/patch/110208-22/log for detailsExecuting postpatch script...postpatch (INFO): Startingpostpatch (INFO): Identified drivers 'lom lomp lomv'postpatch (INFO): Cleaning up old driver 'lom'...Cleaning up old devlink entry 'type=ddi_pseudo;name=SUNW,lom lom'postpatch (INFO): Cleaning up old driver 'lomp'...Cleaning up old devlink entry 'type=ddi_pseudo;name=lomp lomp'postpatch (INFO): Cleaning up old driver 'lomv'...Cleaning up old devlink entry 'type=ddi_pseudo;name=SUNW,lomv \M0type=ddi_pseudo;name=lomv \M0'postpatch (INFO): Cleaning up old driver 'lomh'...Cleaning up old devlink entry 'type=ddi_pseudo;name=SUNW,lomh lom'postpatch (INFO): Adding driver 'lomp'...driver = 'lomp'aliases = ''link = 'lomp'spec = 'lomp'Adding devlink entry 'type=ddi_pseudo;name=lomp lomp'adding driver with aliases '' perm '* 0644 root sys'Cannot find module (lomp).postpatch (ERROR): Failed to add driver, status 1postpatch (INFO): Adding driver 'lomv'...driver = 'lomv'aliases = 'SUNW,lomv'link = 'SUNW,lomv lomv'spec = '\M0'Adding devlink entry 'type=ddi_pseudo;name=SUNW,lomv \M0'Adding devlink entry 'type=ddi_pseudo;name=lomv \M0'adding driver with aliases 'SUNW,lomv' perm '* 0644 root sys'Cannot find module (lomv).postpatch (ERROR): Failed to add driver, status 1postpatch (INFO): Adding driver 'lom'...driver = 'lom'aliases = 'SUNW,lomh SUNW,lom'link = 'SUNW,lomh SUNW,lom'spec = 'lom'Adding devlink entry 'type=ddi_pseudo;name=SUNW,lomh lom'Adding devlink entry 'type=ddi_pseudo;name=SUNW,lom lom'adding driver with aliases 'SUNW,lomh SUNW,lom' perm '* 0644 root sys'Cannot find module (lom).postpatch (ERROR): Failed to add driver, status 1postpatch (ERROR): Failed with status 1The postpatch script exited with return code 1.Backing out patch:Validating patches...Loading patches installed on the system...Done!Checking patches that you specified for removal.Done!Approved patches will be removed in this order:110208-22The installation of patch 110208-22 was interrupted.Patchadd needs to be re-invoked to ensure proper installation of the patch.Patchrm is terminating.WARNING: patchrm returned <14>See /tmp/patchadd-16626830/log.110208-22 for more details.Patchadd is terminating.Installing 126868-01...Installation of 126868-01 succeeded. Return code 0.Installing 118815-06...Installation of 118815-06 succeeded. Return code 0.Installing 119254-50...Installation of 119254-50 succeeded. Return code 0.Installing 126661-02...Installation of 126661-02 succeeded. Return code 0.Installing 125476-02...Installation of 125476-02 succeeded. Return code 0.Installing 125378-03...Installation of 125378-03 succeeded. Return code 0.Installing 121002-04...Installation of 121002-04 succeeded. Return code 0.Installing 120222-23...Installation of 120222-23 succeeded. Return code 0.Installing 125731-02...Installation of 125731-02 succeeded. Return code 0.Installing 119059-38...Installation of 119059-38 succeeded. Return code 0.Installing 119783-05...Installation of 119783-05 succeeded. Return code 0.Installing 120272-16...Installation of 120272-16 succeeded. Return code 0.Installing 128491-01...Installation of 128491-01 succeeded. Return code 0.Installing 125166-07...Installation of 125166-07 succeeded. Return code 0.Installing 125369-13...Installation of 125369-13 succeeded. Return code 0.Installing 127737-01...Installation of 127737-01 succeeded. Return code 0.Installing 125081-14...Installation of 125081-14 succeeded. Return code 0.Installing 128028-03...Installation of 128028-03 succeeded. Return code 0.Installing 127739-03...Installation of 127739-03 succeeded. Return code 0.Installing 124256-05...Installation of 124256-05 succeeded. Return code 0.Installing 127111-06...Installation of 127111-06 succeeded. Return code 0.Installing 125251-02...Installation of 125251-02 succeeded. Return code 0.The following patches were installed:126868-01118815-06119254-50126661-02125476-02125378-03121002-04120222-23125731-02119059-38119783-05120272-16128491-01125166-07125369-13127737-01125081-14128028-03127739-03124256-05127111-06125251-02Check details in /opt/0708patches_log.1892Completed installation of core extra packagesStart core hardeningChanging EEPROM settings..eeprom: OPROMSETOPT: Invalid argumentdiag-level: invalid property.Enable recording of failed login attemptsDump content: kernel pagesDump device: /dev/dsk/c0t1d0s3 (swap)Savecore directory: /var/crash/sh-netra-T2000Savecore enabled: yesCompleted core hardeningCORE CD installation completedEjecting CORE CD...Rebooting ..Oct 28 04:57:47 sh-netra-T2000 reboot: rebooted by rootOct 28 04:57:47 sh-netra-T2000 syslogd: going down on signal 15syncing file systems... donerebooting...SC Alert: Host System has ResetSC Alert: CRITICAL ALARM is set-Netra T2000, No KeyboardCopyright 2008 Sun Microsystems, Inc. All rights reserved.OpenBoot 4.28.6, 16256 MB memory available, Serial #76865034.Ethernet address 0:14:4f:94:de:a, Host ID: 8494de0a.Boot device: disk0 File and args:SunOS Release 5.10 Version Generic_127111-06 64-bitCopyright 1983-2007 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.Hostname: sh-netra-T2000Configuring devices.Loading smf(5) service descriptions: 6/6/dev/rdsk/c0t1d0s5 is cleansh-netra-T2000 console login: rootPassword:Last login: Tue Oct 28 04:42:56 on consoleSun Microsystems Inc. SunOS 5.10 Generic January 2005#Step 6
Note
SunOS 5.10 Generic_127127-11. To verify the version, issue the command uname -a.
Feedback