RPM MIB Objects

Table Of Contents

RPM MIB Objects

Cisco WAN RPM Subinterface MIB Objects

Cisco WAN RPM Subinterface Conformance and Compliance Statements

Cisco WAN RPM Subinterface Compliance Statement

Cisco WAN RPM Subinterface Units of Conformance

Cisco RPM Connection Extension MIB Objects

Cisco RPM Connection Extension Conformance and Compliance Statements

Cisco RPM Connection Extension Compliance Statements

Cisco RPM Connection Extension Units of Conformance

RPM MIB Objects

---

This chapter describes the MIB objects used for Router Processor Module (RPM).

Contents of this chapter include:

•Cisco WAN RPM Subinterface MIB Objects

•Cisco RPM Connection Extension MIB Objects

Cisco WAN RPM Subinterface MIB Objects

This section describes the individual MIB objects that make up the Cisco WAN RPM Subinterface file, which resides in the CISCO-WAN-RPM-SUBIF-MIB.my file. These MIBs are used to provision backplane subinterfaces on RPM.

---

Note The Cisco WAN RPM Subinterface MIB is defined under the StrataCom Enterprise.

---

The object identifier for each MIB object is listed in Table 6-1.

Table 6-1 Cisco WAN RPM Subinterface Object Identifiers 

Name	Object Identifier
cwRpmSubIfMIBObjects	::= { ciscoWanRpmSubIfMIB 1 }
cwRpmSubIf	::= { cwRpmSubIfMIBObjects 1 }
cwRpmSubIfTable	::= { cwRpmSubIf 1 }
cwRpmSubIfEntry	::= { cwRpmSubIfTable 1 }
cwrSubIfSlotNum	::= { cwRpmSubIfEntry 1 }
cwrSubIfNum	::= { cwRpmSubIfEntry 2 }
cwrSubIfAdapterIf	::= { cwRpmSubIfEntry 3 }
cwrSubIfType	::= { cwRpmSubIfEntry 4 }
cwrSubIfIpAddress	::= { cwRpmSubIfEntry 5 }
cwrSubIfSubnetMask	::= { cwRpmSubIfEntry 6 }
cwrSubIfRowStatus	::= { cwRpmSubIfEntry 7 }

The MIB objects are listed in Table 6-2.

Table 6-2 Cisco WAN RPM Subinterface MIB Objects 

Name	Syntax	Description		Default Value
cwRpmSubIfTable	SEQUENCE OF CwRpmSubIfEntry	Contains the RPM backplane subinterfaces. Max-Access: not-accessible Status: current		none
cwRpmSubIfEntry	CwRpmSubIfEntry	Corresponds to a RPM backplane subinterface for each entry. It contains the RPM backplane subinterface number, IP address, type, and state. Max-Access: not-accessible Status: current The indexes include: •cwrSubIfSlotNum •cwrSubIfNum		none
cwrSubIfSlotNum	Unsigned32 (1..32)	Specifies the slot number of the RPM card. Max-Access: not-accessible Status: current		none
cwrSubIfNum	Unsigned32 (1..4294967295)	Specifies the subinterface number. Max-Access: not-accessible Status: current		none
cwrSubIfAdapterIf	Unsigned32	Maps to the RPM for port adapter interface. Currently, one port adapter interface is supported. Note This object is supported as read-only. Max-Access: read-create Status: current		none
cwrSubIfType	INTEGER { pointToPoint(1), multiPoint(2), labelSwitching(3)}	Specifies the link type of this subinterface. Max-Access: read-create Status: current		none
cwrSubIfIpAddress	IpAddress	Specifies the 4-octet IP address of the RPM subinterface. Max-Access: read-create Status: current		none
cwrSubIfSubnetMask	IpAddress	Specifies the 4-octet subnet mask of the RPM subinterface. Max-Access: read-create Status: current		none
cwrSubIfRowStatus	RowStatus	Specifies the administrative status of this subinterface. A row is created using the CreateAndGo option. When the row is successfully created, the RowStatus is set to active by the agent. When the subinterface is administratively downed, the RowStatus is set to notInService. If the subinterface is administratively upped again, the RowStatus is set to active again. The subinterface is deleted by setting the RowStatus to destroy. Other options such as CreateAndWait is not used. Max-Access: read-create Status: current		none

Cisco WAN RPM Subinterface Conformance and Compliance Statements

The object identifiers are listed in Table 6-3 for conformance.

Table 6-3 Cisco WAN RPM Subinterface Object Identifier

Name	Object Identifier
ciscoWanRpmSubIfMIBConformance	::= { ciscoWanRpmSubIfMIB 2 }
ciscoWanRpmSubIfMIBCompliances	::= { ciscoWanRpmSubIfMIBConformance 1 }
ciscoWanRpmSubIfMIBGroups	::= { ciscoWanRpmSubIfMIBConformance 2 }

Cisco WAN RPM Subinterface Compliance Statement

The compliance object identifier is listed in Table 6-4.

Table 6-4 Cisco WAN RPM Subinterface Object Identifier

Name	Object Identifier
ciscoWanRpmSubIfMIBCompliance	::= { ciscoWanRpmSubIfMIBCompliances 1 }

One MIB object is listed in Table 6-5.

Table 6-5 Cisco WAN RPM Subinterface Compliance MIB Object

Name	Mandatory Group	Description	Default Value
ciscoWanRpmSubIfMIBCompliance	ciscoWanRpmSubIfMIBGroup	Describes the compliance statement for the Cisco MGX RPM subinterface management group. Status: current	none

Cisco WAN RPM Subinterface Units of Conformance

One object identifier is listed in Table 6-6.

Table 6-6 Cisco WAN RPM Subinterface Units of Conformance Object Identifier

Name	Object Identifier
ciscoWanRpmSubIfMIBGroup	::= { ciscoWanRpmSubIfMIBGroups 1 }

One object is listed in Table 6-7 for units of conformance.

Table 6-7 Cisco WAN RPM Subinterface Units of Conformance MIB Object

Name	Objects	Description	Default Value
ciscoWanRpmSubIfMIBGroup	cwrSubIfAdapterIf, cwrSubIfType, cwrSubIfIpAddress, cwrSubIfSubnetMask, cwrSubIfRowStatus}	Describes the conformance for the Cisco MGX RPM subinterface management group. Status: current	none

Cisco RPM Connection Extension MIB Objects

This section describes the individual MIB objects that make up the Cisco RPM Connection Extension file, which resides in the CISCO-WAN-RPM-CONN-EXT-MIB.my file. These MIBs are used to provision the Permanent Virtual Circuit (PVC) endpoints and Switched Permanent Virtual Circuit (SPVC) on RPM.

---

Note The Cisco RPM Connection Extension MIB is defined under the StrataCom Enterprise.

---

The object identifier for each MIB object is listed in Table 6-8.

Table 6-8 Cisco RPM Connection Extension Object Identifiers 

Name	Object Identifier
cwRpmConnExtMIBObjects	::= { ciscoWanRpmConnExtMIB 1 }
cwRpmConnExt	::= { cwRpmConnExtMIBObjects 1 }
cwRpmChanExtTable	::= { cwRpmConnExt 1 }
cwRpmChanExtEntry	::= { cwRpmChanExtTable 1 }
cwrChanSubInterface	::= { cwRpmChanExtEntry 1 }
cwrChanVcd	::= { cwRpmChanExtEntry 2 }
cwrChanAalEncapType	::= { cwRpmChanExtEntry 3 }
cwrChanVirtualTemplate	::= { cwRpmChanExtEntry 4 }
cwrChanInArpInterval	::= { cwRpmChanExtEntry 5 }
cwrChanOamLoopbkTxInterval	::= { cwRpmChanExtEntry 6 }
cwrChanOamManage	::= { cwRpmChanExtEntry 7 }
cwrChanOamRetryUpCount	::= { cwRpmChanExtEntry 8 }
cwrChanOamRetryDownCount	::= { cwRpmChanExtEntry 9 }
cwrChanOamRetryInterval	::= { cwRpmChanExtEntry 10 }

The MIB objects are listed in Table 6-9.

Table 6-9 Cisco RPM Connection Extension MIB Objects 

Name	Syntax	Description		Default Value
cwRpmChanExtTable	SEQUENCE OF CwRpmChanExtEntry	Supports the provisioning of PVC endpoints and SPVCs on an RPM along with the cwAtmChanCnfgTable. cwRpmChanExtTable contains objects that are specific to RPM. This table is an augmentation to the cwAtmChanCnfgTable. Max-Access: not-accessible Status: current		none
cwRpmChanExtEntry	CwRpmChanExtEntry	Contains RPM-specific parameters for a connection endpoint on a RPM. Max-Access: not-accessible Status: current Augment: cwAtmChanCnfgEntry		none
cwrChanSubInterface	Unsigned32 (0..4294967295)	Specifies the RPM backplane subinterface where this channel is configured. Subinterface is 0 for the switch port. Max-Access: read-create Status: current		0
cwrChanVcd	Unsigned32 (0..4095)	Describes the Virtual Circuit Descriptor (VCD) used to identify a connection for the unique number. Max-Access: read-only Status: current		none
cwrChanAalEncapType	INTEGER { aal5ciscoPPP(1), aal5muxAPOLLO(2), aal5muxAPPLETALK(3), aal5muxDECNET(4), aal5muxIP(5),| aal5muxIPX(6), aal5muxPPP(7), aal5muxVINES(8), aal5muxXNS(9), aal5nlpid(10), aal5snap(11), ilmi(12), qsaal(13)}	Specifies the ATM Adaptation Layer (AAL) and encapsulation. Max-Access: read-create Status: current The parameters include: •aal5ciscoPPP—Specifies that cwrChanVirtualTemplate is required to be set for Cisco Point-to-Point (PPP) over ATM. •aal5muxAPOLLO—Specifies the Multiplexing Device (mux) type virtual circuit that is used for the Apollo protocol. •aa15muxAPPLETALK—Specifies the mux type for the virtual circuit that is used for the AppleTalk protocol. •aal5muxDECNET—Specifies the mux type for the virtual circuit that is used for the DECnet protocol. •aal5muxIP—Specifies the mux type for the virtual circuit that is used for the IP protocol. •aal5muxIPX—Specifies the mux type for the virtual circuit that is used for the IPX protocol. •aal5muxPPP—Specifies the mux type for the virtual circuit that is used for PPP. cwrChanVirtualTemplate is required to be set for this type. •aal5muxVINES—Specifies the mux type for the virtual circuit that is used for Virtual Integrated Network Service (VINES). •aal5muxXNS—Specifies the mux type for the virtual circuit that is used for Xerox Network Systems (XNS). •aal5nlpid—Allows ATM interfaces to interoperate with High-Speed Serial Interface (HSSI). •aal5snap—Supports Inverse ARP (Address Resolution Protocol) that is used only for encapsulation. Logical Link Control/Subnetwork Access Protocol (LLC/SNAP) precedes the protocol datagram. •ilmi—Sets up communication with Interim Local Management Interface (ILMI). •qsaal—Sets up or tears down the Switched Virtual Circuit (SVC) for the Permanent Virtual Circuit (PVC) signaling type.		aal5snap
cwrChanVirtual Template	Unsigned32 (0..25)	Requires Cisco PPP or mux-type PPP encapsulation, for example, cwrChanAalEncapType = aal5ciscoPPP or aal5muxPPP. cwrChanVirtualTemplate specifies the number used to identify the virtual template. If the virtual template is not used, this value is 0. Max-Access: read-create Status: current		0
cwrChanInArpInterval	Unsigned32 (0..60)	Specifies how often Inverse ARP datagrams are sent on this channel. The value 0 disables InArp for this channel. This object is supported only for aal5snap encapsulation, for example, cwrChanAalEncapType = aal5snap. Units: minutes Max-Access: read-create Status: current		15
cwrChanOamLoopbk TxInterval	Unsigned32 (0..600)	Specifies how often to generate an Operation, Administration, Maintenance (OAM) F5 loopback cell from this channel. The value 0 disables generation of OAM F5 loopback cells. Units: seconds Max-Access: read-create Status: current		10
cwrChanOamManage	TruthValue	Enables and disables OAM management for this channel. If set to true(1), OAM management is enabled. Max-Access: read-create Status: current		false
cwrChanOamRetryUp Count	Unsigned32 (1..600)	Determines the number of consecutive end-to-end F5 OAM loopback cell responses that must be received to change a PVC connection state to up. This object applies only if OAM management is enabled, for example, cwrChanOAMManage = true. Max-Access: read-create Status: current		3
cwrChanOamRetry DownCount	Unsigned32 (1..600)	Determines the number of consecutive end-to-end F5 OAM loopback cell responses that are not received to change a PVC connection state to down. This object applies only if OAM management is enabled, for example, cwrChanOAMManage = true. Max-Access: read-create Status: current		5
cwrChanOamRetry Interval	Unsigned32 (1..1000)	Specifies the frequency for end-to-end F5 OAM loopback cells that are transmitted when a change in up/down state of a PVC is being verified. This object applies only if OAM management is enabled, for example, cwrChanOAMManage = true. Units: seconds Max-Access: read-create Status: current		1

Cisco RPM Connection Extension Conformance and Compliance Statements

The object identifiers are listed in Table 6-10 for conformance.

Table 6-10 Cisco RPM Connection Extension Conformance Groups

Name	Object Identifier
ciscoWanRpmConnExtMIBConformance	::= { ciscoWanRpmConnExtMIB 2 }
ciscoWanRpmConnExtMIBCompliances	::= { ciscoWanRpmConnExtMIBConformance 1 }
ciscoWanRpmConnExtMIBGroups	::= { ciscoWanRpmConnExtMIBConformance 2 }

Cisco RPM Connection Extension Compliance Statements

The compliance object identifier is listed in Table 6-11.

Table 6-11 Cisco RPM Connection Extension Object Identifier

Name	Object Identifier
ciscoWanRpmConnExtMIBCompliance	::= { ciscoWanRpmConnExtMIBCompliances 1 }

One MIB object is listed in Table 6-12.

Table 6-12 Cisco RPM Connection Extension Compliance MIB Object

Name	Mandatory Group	Description	Default Value
ciscoWanRpmConn ExtMIBCompliance	ciscoWanRpmConnExtMIBGroup	Describes the compliance statement for the RPM connection management group.	none

Cisco RPM Connection Extension Units of Conformance

One object identifier is listed in Table 6-13.

Table 6-13 Cisco RPM Connection Extension Units of Conformance Object Identifier

Name	Object Identifier
ciscoWanRpmConnExtMIBGroup	::= { ciscoWanRpmConnExtMIBGroups 1 }

One object is listed in Table 6-14 for units of conformance.

Table 6-14 Cisco RPM Connection Extension Compliance MIB Object

Name	Objects	Description	Default Value
ciscoWanRpmConn ExtMIBGroup	cwrChanSubInterface, cwrChanVcd, cwrChanAalEncapType, cwrChanVirtualTemplate, cwrChanInArpInterval, cwrChanOamLoopbkTxInterval, cwrChanOamManage, cwrChanOamRetryUpCount, cwrChanOamRetryDownCount, cwrChanOamRetryInterval}	Describes the conformance for the RPM connection management group. Status: current	none