OMS controller

When nodes with Mux/Demux panels and breakout panels are brought up, OMS controllers are created by default. The OMS controllers for the patch panels are:

Table 1. Supported interfaces

Patch panel	Port type	OMS ports	Interfaces
NCS1K-BRK-8	MPO Ports	8	oms R/S/I/8 to oms R/S/I/15
NCS1K-BRK-24	MPO Ports	8	oms R/S/I/24 to oms R/S/I/31
NCS1K-MD-32O/E-C	LC Ports	1	oms R/S/I/32

Note

R/S/I/P stands for Rack/Slot/Instance/Port.

To view the status of the OMS controller, use this command:

RP/0/RP0/CPU0:ios#show controller description

This output shows the status of the OMS controller.

Tue Apr 12 17:17:51.306 UTC

Interface                   Status          Description
--------------------------------------------------------------------------------
Och0/1/0/0                  up
Och0/1/0/1                  up
Och0/1/0/2                  up
.
.
Output snipped
.
.
Och0/1/0/29                 up
Och0/1/0/30                 up
Och0/1/0/31                 up
Oms0/1/0/32                 up
Och0/3/0/0                  up
Och0/3/0/1                  up
.
.
Output snipped
.
.
Och0/3/0/29                 up
Och0/3/0/30                 up
Och0/3/0/31                 up
Oms0/3/0/32                 up

To view the parameters of the OMS controller for the BRK-24 panel, use this command:

RP/0/RP0/CPU0:ios#show controllers oms 0/1/0/25

This output shows the parameters of the OMS controller for the BRK-24 panel.

Thu Jul 14 11:05:50.419 UTC

 Controller State: Down 

 Transport Admin State: Automatic In Service 

 LED State: Red 

         Alarm Status:
         -------------
         Detected Alarms: 
                 RX-LOS-P    

         Alarm Statistics:
         -----------------
         RX-LOS-P = 1         
         TX-POWER-FAIL-LOW = 0

         Parameter Statistics:
         ---------------------
         TX Power = -7.40 dBm 
         RX Power = -50.00 dBm

To view the parameters of the OMS controller for the Mux/Demux panel, use this command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/32 

This output shows the parameters of the OMS controller for the Mux/Demux panel.

Tue May 10 11:28:02.856 UTC

 Controller State: Down 

 LED State: Red 

         Alarm Status:
         -------------
         Detected Alarms: 
                 RX-LOS-P    

         Alarm Statistics:
         -----------------
         RX-LOS-P = 1          
         TX-POWER-FAIL-LOW = 0          

         Parameter Statistics:
         ---------------------
         TX Power = -50.00 dBm 
         RX Power = -50.00 dBm 

Insertion loss for each port is calculated and the power values are displayed on the OMS controller for NCS1K-BRK-8 and OCH controller for NCS1K-BRK-24. Insertion loss per port for NCS1K-BRK-24 is 5.9 dBm and NCS1K-BRK-8 is 0.6 dBm. The NCS1K-MD-32O/E-C panels have a maximum insertion loss of 6.2 dBm for the respective Mux and Demux sections.