Available Languages

Download Options

PDF (630.0 KB)
View with Adobe Reader on a variety of devices

Updated:April 20, 2017

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Upgrade Scenarios Covered in the MOP

· Upgrade from 6.0.1 + k9 sec (with or without SMUs installed) to R6.1.2 with k9sec + CDR3 SMU – Recommended

· R6.1.2 Prod SMU Installation – Only for already upgraded boxes

Scenario -1 : Upgrade from 6.0.1 + k9 sec + Prod SMUs (both) to R6.1.2 with k9sec + CDR3 SMU

Steps involved: (Overall time required : 1 hour 10 mins)

1. Validating the current status (5 mins)

2. Upgrade of SW and SMU (15 mins)

3. Updating FPD & Slice status (Traffic impact will be observed) (40 mins)

4. Validating the status after upgrade (10 mins)

1. Baseline the current status by executing below command. Please log the output for reference during and after the procedure

1.1 XR Active packages:

RP/0/RP0/CPU0:ios#show install active

Mon Apr 3 11:45:05.441 UTC

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv0

Active Packages: 6

ncs1k-xr-6.0.1 version=6.0.1 [Boot image]

ncs1k-k9sec-2.0.0.0-r601

ncs1k-iosxr-infra-2.0.0.1-r601.CSCuz86633

ncs1k-parser-1.0.0.1-r601.CSCuz86633

ncs1k-os-support-2.0.0.1-r601.CSCuz86634

ncs1k-os-support-2.0.0.2-r601.CSCvb35594

1.2 XR committed packages:

RP/0/RP0/CPU0:ios#show install committed

Mon Apr 3 11:45:42.563 UTC

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv0

Committed Packages: 6

ncs1k-xr-6.0.1 version=6.0.1 [Boot image]

ncs1k-k9sec-2.0.0.0-r601

ncs1k-iosxr-infra-2.0.0.1-r601.CSCuz86633

ncs1k-parser-1.0.0.1-r601.CSCuz86633

ncs1k-os-support-2.0.0.1-r601.CSCuz86634

ncs1k-os-support-2.0.0.2-r601.CSCvb35594

1.3 Ncs1k-sysadmin Active packages:

sysadmin-vm:0_RP0# show install active

Mon Apr 3 12:13:48.102 UTC

Node 0/RP0 [RP]

Active Packages: 4

ncs1k-sysadmin-6.0.1 version=6.0.1 [Boot image]

ncs1k-sysadmin-ncs-common-6.0.1.2-r601.CSCva41433

ncs1k-sysadmin-ncs1k-6.0.1.2-r601.CSCva41433

ncs1k-sysadmin-shared-6.0.1.1-r601.CSCva41433

1.4 Ncs1k-sysadmin committed packages

sysadmin-vm:0_RP0# show install committed

Mon Apr 3 12:14:02.590 UTC

Node 0/RP0 [RP]

Committed Packages: 4

ncs1k-sysadmin-6.0.1 version=6.0.1 [Boot image]

ncs1k-sysadmin-ncs-common-6.0.1.2-r601.CSCva41433

ncs1k-sysadmin-ncs1k-6.0.1.2-r601.CSCva41433

ncs1k-sysadmin-shared-6.0.1.1-r601.CSCva41433

1.5 Current FPD Status:

RP/0/RP0/CPU0:ios#show hw-module fpd

Mon Apr 3 11:58:27.832 UTC

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.62 3.62

0/0 NCS1002-K9 CFP2_PORT_05 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_12 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_19 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_26 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 1.22

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 1.22

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 1.22 1.22

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 1.22 1.22

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S CURRENT 13.10 13.10

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

1.6 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

RP/0/RP0/CPU0:ios#show hw-module slice all

2. Upgrade to 6.1.2 CCO + PROD.SMU (No traffic impact expected, 20 mins)

2.1 Software Upgrade Steps:

Customers are strictly recommended to Add and Activate both CCO Image and SMU’s together in a single step.

Install add source <6.1.2.image tar or mini.iso + k9sec> <ncs1k-6.1.2.CSCvd63122.tar> <ncs1k-sysadmin-6.1.2.CSCvc80004.tar>

install activate id <add id>

System will go for reload.

install commit

Note: Please refer to Cisco NCS1002 SMU install guide for actual commands. http://www.cisco.com/web/Cisco_IOS_XR_Software/pdf/NCS1K-System-Upgrade.pdf

2.2 XR Active packages:

RP/0/RP0/CPU0:ios#show install active

Mon Apr 3 12:47:35.114 UTC

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv8

Active Packages: 5

ncs1k-xr-6.1.2 version=6.1.2 [Boot image]

ncs1k-k9sec-3.1.0.0-r612

ncs1k-iosxr-infra-4.0.0.1-r612.CSCvd63122

ncs1k-os-support-3.0.0.1-r612.CSCvd63122

ncs1k-iosxr-os-5.0.0.1-r612.CSCvd63122

2.3 XR committed packages:

RP/0/RP0/CPU0:ios#show install committed

Mon Apr 3 12:47:38.917 UTC

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv8

Committed Packages: 5

ncs1k-xr-6.1.2 version=6.1.2 [Boot image]

ncs1k-k9sec-3.1.0.0-r612

ncs1k-iosxr-infra-4.0.0.1-r612.CSCvd63122

ncs1k-os-support-3.0.0.1-r612.CSCvd63122

ncs1k-iosxr-os-5.0.0.1-r612.CSCvd63122

2.4 Ncs1k-sysadmin Active packages

sysadmin-vm:0_RP0# show install active

Mon Apr 3 12:48:21.169 UTC

Node 0/RP0 [RP]

Active Packages: 3

ncs1k-sysadmin-6.1.2 version=6.1.2 [Boot image]

ncs1k-sysadmin-ncs1k-6.1.2.1-r612.CSCvc80004

ncs1k-sysadmin-shared-6.1.2.1-r612.CSCvc80004

2.5 Ncs1k-sysadmin committed packages

sysadmin-vm:0_RP0# show install committed

Mon Apr 3 12:48:28.309 UTC

Node 0/RP0 [RP]

Committed Packages: 3

ncs1k-sysadmin-6.1.2 version=6.1.2 [Boot image]

ncs1k-sysadmin-ncs1k-6.1.2.1-r612.CSCvc80004

ncs1k-sysadmin-shared-6.1.2.1-r612.CSCvc80004

2.6 FPD Status after SU

RP/0/RP0/CPU0:ios#show hw-module fpd

Mon Apr 3 12:49:01.294 UTC

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_06 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_12 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_13 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_19 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_20 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_26 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 1.2 CDSP_PORT_27 NEED UPGD 3.62 3.62

0/0 NCS1002-K9 CFP2_PORT_05 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_12 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_19 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_26 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B NEED UPGD 1.22

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B NEED UPGD 1.22

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW NEED UPGD 1.22 1.22

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP NEED UPGD 1.22 1.22

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S NEED UPGD 13.10 13.10

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

2.7 Slice Status after SU

1. Verify all Slice status shows NEED_UPGRADE after SU

3. FPD Upgrade Steps

[BIOS, CTRL FPGA, CDSP needs upgrade]

Note: FPD Upgrade is recommended only by executing “upgrade hw-module location all fpd all”.

Do not perform “hw-module location 0/RP0 reload “ command after BIOS upgrade. Strictly not recommended in R6.1.2.

3.1 FPD Upgrade:

1. From XR , Upgrade fpd all via “upgrade hw-module location all fpd all”

RP/0/RP0/CPU0:ios#show hw-module fpd

Mon Apr 3 13:22:13.170 UTC

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.65 3.65

0/0 NCS1002-K9 CFP2_PORT_05 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_12 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_19 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_26 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW RLOAD REQ 1.22 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP RLOAD REQ 1.22 2.23

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S RLOAD REQ 13.10 13.41

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT

3.2 Reload NCS1K

1. From Ncs1k-sysadmin , Reload using “ hw-module location all reload”

Note: This action is expected to be traffic impacting. Expected hit time: 30 minutes

4. Validate FPD and Slice Status

4.1 Verify FPD all

RP/0/RP0/CPU0:ios#show hw-module fpd

Mon Apr 3 13:29:12.934 UTC

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.65 3.65

0/0 NCS1002-K9 CFP2_PORT_05 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_12 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_19 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_26 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 2.23 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 2.23 2.23

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S CURRENT 13.41 13.41

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

4.2 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

RP/0/RP0/CPU0:ios#show hw-module slice all

Mon Apr 3 13:49:24.014 UTC

Slice ID: 0

Status: Provisioned

Client Bitrate: 100

Trunk Bitrate: 200

DP FPGA FW Type: X100

DP FPGA FW Version: 01.01

HW Status: CURRENT

Encryption Supported: FALSE

LLDP Drop Enabled: FALSE

Client Port - Trunk Port CoherentDSP0/0/0/5 CoherentDSP0/0/0/6

Traffic Split Percentage

HundredGigECtrlr0/0/0/0 100 0

HundredGigECtrlr0/0/0/1 100 0

HundredGigECtrlr0/0/0/3 0 100

HundredGigECtrlr0/0/0/4 0 100

Note : If Slice Status is still in NEED_UPGRADE after provisioning is completed, perform “upgrade hw-module slice <no.> re-provision” and then verify Slice status.

4.3 Verify environment voltages on ncs1k-sysadmin

Note: Highlighted voltage values should be greater than 950.

sysadmin-vm:0_RP0# show environment voltages | inc CDR | inc V0P9

Mon Apr 3 13:31:05.383 UTC

Down-SLICE2-V0P9_CDR3 996 810 860 1050 1100

Down-SLICE3-V0P9_CDR3 1014 810 860 1050 1100

Up-SLICE0-V0P9_CDR3 998 810 860 1050 1100

Up-SLICE1-V0P9_CDR3 1014 810 860 1050 1100

Note 1 : For unprovisioisned slices ignore Voltage values.

Note 2 : If the above highlighted output values are less than 950, perform “upgrade hw-module slice <no.> re-provision” (from xr prompt) again and verify highlighted voltage should be greater than 950.

Note 3 : Please contact Cisco TAC if there are any unresolved issues during this MOP

Scenario -2 : R6.1.2 Prod SMU Installation – Only for already upgraded boxes

Steps involved: (Overall time required : 1 hour 10 mins)

1. Validating the current status (5 mins)

2. Upgrade of SMU (15 mins)

3. Updating FPD & Slice status (Traffic impact will be observed) (40 mins)

4. Validating the status after upgrade (10 mins)

1. Baseline the current status by executing below command. Please log the output for reference during and after the procedure

Note: If ENG SMU is installed then please do deactivate and remove package before proceeding. Please refer to the following to deactivate and remove the SMU. This is mandatory step before proceeding.

http://www.cisco.com/web/Cisco_IOS_XR_Software/pdf/NCS1K-System-Upgrade.pdf

1.1 XR Active packages:

RP/0/RP0/CPU0:ios#show install active

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv7

Active Packages: 2

ncs1k-xr-6.1.2 version=6.1.2 [Boot image]

ncs1k-k9sec-3.1.0.0-r612

1.2 XR committed packages:

RP/0/RP0/CPU0:ios#show install committed

Thu Apr 6 12:27:21.132 IST

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv7

Committed Packages: 2

ncs1k-xr-6.1.2 version=6.1.2 [Boot image]

ncs1k-k9sec-3.1.0.0-r612

1.3 Ncs1k-sysadmin Active packages:

sysadmin-vm:0_RP0# show install active

Thu Apr 6 06:57:29.176 UTC

Node 0/RP0 [RP]

Active Packages: 1

ncs1k-sysadmin-6.1.2 version=6.1.2 [Boot image]

1.4 Ncs1k-sysadmin committed packages

sysadmin-vm:0_RP0# show install commit

Thu Apr 6 06:57:34.390 UTC

Node 0/RP0 [RP]

Committed Packages: 1

ncs1k-sysadmin-6.1.2 version=6.1.2 [Boot image]

1.5 Current FPD Status:

RP/0/RP0/CPU0:ios#show hw-module fpd

Thu Apr 6 13:52:49.809 IST

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.65 3.65

0/0 NCS1002-K9 2.0 CFP2_PORT_05 CURRENT 4.38 4.38

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_12 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_19 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_26 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 2.23 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 2.23 2.23

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S CURRENT 13.40 13.40

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

1.6 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

RP/0/RP0/CPU0:ios#show hw-module slice all

Thu Apr 6 13:52:46.271 IST

Slice ID: 0

Status: Provisioned

Client Bitrate: 100

Trunk Bitrate: 250

DP FPGA FW Type: X100

DP FPGA FW Version: 01.01

HW Status: CURRENT

Encryption Supported: FALSE

LLDP Drop Enabled: FALSE

Client Port - Trunk Port CoherentDSP0/0/0/5 CoherentDSP0/0/0/6

Traffic Split Percentage

HundredGigECtrlr0/0/0/0 100 0

HundredGigECtrlr0/0/0/1 100 0

HundredGigECtrlr0/0/0/2 50 50

HundredGigECtrlr0/0/0/3 0 100

HundredGigECtrlr0/0/0/4 0 100

Slice ID: 1

Status: Provisioned

Client Bitrate: 100

Trunk Bitrate: 250

DP FPGA FW Type: X100

DP FPGA FW Version: 01.01

HW Status: CURRENT

Encryption Supported: FALSE

LLDP Drop Enabled: FALSE

Client Port - Trunk Port CoherentDSP0/0/0/12 CoherentDSP0/0/0/13

Traffic Split Percentage

HundredGigECtrlr0/0/0/7 100 0

HundredGigECtrlr0/0/0/8 100 0

HundredGigECtrlr0/0/0/9 50 50

HundredGigECtrlr0/0/0/10 0 100

HundredGigECtrlr0/0/0/11 0 100

Slice ID: 2

Status: Provisioned

Client Bitrate: 100

Trunk Bitrate: 250

DP FPGA FW Type: X100

DP FPGA FW Version: 01.01

HW Status: CURRENT

Encryption Supported: FALSE

LLDP Drop Enabled: FALSE

Client Port - Trunk Port CoherentDSP0/0/0/19 CoherentDSP0/0/0/20

Traffic Split Percentage

HundredGigECtrlr0/0/0/14 100 0

HundredGigECtrlr0/0/0/15 100 0

HundredGigECtrlr0/0/0/16 50 50

HundredGigECtrlr0/0/0/17 0 100

HundredGigECtrlr0/0/0/18 0 100

Slice ID: 3

Status: Provisioned

Client Bitrate: 100

Trunk Bitrate: 250

DP FPGA FW Type: X100

DP FPGA FW Version: 01.01

HW Status: CURRENT

Encryption Supported: FALSE

LLDP Drop Enabled: FALSE

Client Port - Trunk Port CoherentDSP0/0/0/26 CoherentDSP0/0/0/27

Traffic Split Percentage

HundredGigECtrlr0/0/0/21 100 0

HundredGigECtrlr0/0/0/22 100 0

HundredGigECtrlr0/0/0/23 50 50

HundredGigECtrlr0/0/0/24 0 100

HundredGigECtrlr0/0/0/25 0 100

2. Upgrade to 6.1.2 CCO + PROD.SMU (No traffic impact expected)

2.1 SMU Upgrade Steps:

Customers are strictly recommended to Add and Activate SMU as a tar file (of all rpms) together in a single step.

Install add source <ncs1k-6.1.2.CSCvd63122.tar> <ncs1k-sysadmin-6.1.2.CSCvc80004.tar>

install activate id <add id>

System will go for reload.

install commit

Note: Please refer to Cisco NCS1002 SMU install guide for actual commands. http://www.cisco.com/web/Cisco_IOS_XR_Software/pdf/NCS1K-System-Upgrade.pdf

2.2 XR Active packages:

RP/0/RP0/CPU0:ios#show install active

Mon Apr 3 12:47:35.114 UTC

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv8

Active Packages: 5

ncs1k-xr-6.1.2 version=6.1.2 [Boot image]

ncs1k-k9sec-3.1.0.0-r612

ncs1k-iosxr-infra-4.0.0.1-r612.CSCvd63122

ncs1k-os-support-3.0.0.1-r612.CSCvd63122

ncs1k-iosxr-os-5.0.0.1-r612.CSCvd63122

2.3 XR committed packages:

RP/0/RP0/CPU0:ios#show install committed

Mon Apr 3 12:47:38.917 UTC

Node 0/RP0/CPU0 [RP]

Boot Partition: xr_lv8

Committed Packages: 5

ncs1k-xr-6.1.2 version=6.1.2 [Boot image]

ncs1k-k9sec-3.1.0.0-r612

ncs1k-iosxr-infra-4.0.0.1-r612.CSCvd63122

ncs1k-os-support-3.0.0.1-r612.CSCvd63122

ncs1k-iosxr-os-5.0.0.1-r612.CSCvd63122

2.4 Ncs1k-sysadmin Active packages

sysadmin-vm:0_RP0# show install active

Mon Apr 3 12:48:21.169 UTC

Node 0/RP0 [RP]

Active Packages: 3

ncs1k-sysadmin-6.1.2 version=6.1.2 [Boot image]

ncs1k-sysadmin-ncs1k-6.1.2.1-r612.CSCvc80004

ncs1k-sysadmin-shared-6.1.2.1-r612.CSCvc80004

2.5 Ncs1k-sysadmin committed packages

sysadmin-vm:0_RP0# show install committed

Mon Apr 3 12:48:28.309 UTC

Node 0/RP0 [RP]

Committed Packages: 3

ncs1k-sysadmin-6.1.2 version=6.1.2 [Boot image]

ncs1k-sysadmin-ncs1k-6.1.2.1-r612.CSCvc80004

ncs1k-sysadmin-shared-6.1.2.1-r612.CSCvc80004

2.6 FPD Status after SMU Upgrade:

RP/0/RP0/CPU0:ios#show hw-module fpd

Thu Apr 6 14:16:27.485 IST

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.65 3.65

0/0 NCS1002-K9 2.0 CFP2_PORT_05 CURRENT 4.38 4.38

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_12 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_19 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_26 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 2.23 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 2.23 2.23

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S NEED UPGD 13.40 13.40

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

2.7 Slice Status after SU

Verify All Slices shows NEED_UPGRADE in “show hw-module slice all”

3. FPD Upgrade Steps

3.1 FPD Upgrade:

1. From XR , Upgrade fpd all via “upgrade hw-module location all fpd all” (Takes 2 mins)

RP/0/RP0/CPU0:ios#show hw-module fpd

Thu Apr 6 14:57:47.700 IST

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.65 3.65

0/0 NCS1002-K9 2.0 CFP2_PORT_05 CURRENT 4.38 4.38

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_12 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_19 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_26 CURRENT 5.21 5.21

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 2.23 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 2.23 2.23

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S RLOAD REQ 13.40 13.41

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

3.2 Reload NCS1K

5. From Ncs1k-sysadmin , Reload using “hw-module location all reload”

Note: This action is expected to be traffic impacting. Expected hit time: 30 minutes

4. Validate FPD and Slice Status

4.1 Verify FPD all

RP/0/RP0/CPU0:ios#show hw-module fpd

Mon Apr 3 13:29:12.934 UTC

FPD Versions

=================

Location Card type HWver FPD device ATR Status Running Programd

------------------------------------------------------------------------------

0/0 NCS1002-K9 1.2 CDSP_PORT_05 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_06 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_12 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_13 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_19 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_20 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_26 CURRENT 3.65 3.65

0/0 NCS1002-K9 1.2 CDSP_PORT_27 CURRENT 3.65 3.65

0/0 NCS1002-K9 CFP2_PORT_05 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_06 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_12 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_13 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_19 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_20 CURRENT 5.21 5.21

0/0 NCS1002-K9 CFP2_PORT_26 NOT READY

0/0 NCS1002-K9 2.1 CFP2_PORT_27 CURRENT 5.21 5.21

0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 2.23 2.23

0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 2.23 2.23

0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 13.10

0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S CURRENT 13.41 13.41

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15

0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.15 0.15

0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU CURRENT 4.00 4.00

4.2 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

RP/0/RP0/CPU0:ios#show hw-module slice all

Mon Apr 3 13:49:24.014 UTC

Slice ID: 0

Status: Provisioned

Client Bitrate: 100

Trunk Bitrate: 200

DP FPGA FW Type: X100

DP FPGA FW Version: 01.01

HW Status: CURRENT

Encryption Supported: FALSE

LLDP Drop Enabled: FALSE

Client Port - Trunk Port CoherentDSP0/0/0/5 CoherentDSP0/0/0/6

Traffic Split Percentage

HundredGigECtrlr0/0/0/0 100 0

HundredGigECtrlr0/0/0/1 100 0

HundredGigECtrlr0/0/0/3 0 100

HundredGigECtrlr0/0/0/4 0 100

Note : If Slice Status is still in NEED_UPGRADE after provisioning is completed, perform “upgrade hw-module slice <no.> re-provision” and then verify Slice status.

4.3 Verify environment voltages on ncs1k-sysadmin

Note: Highlighted voltage values should be greater than 950

sysadmin-vm:0_RP0# show environment voltages | inc CDR | inc V0P9

Mon Apr 3 13:31:05.383 UTC

Down-SLICE2-V0P9_CDR3 1017 810 860 1050 1100

Down-SLICE3-V0P9_CDR3 999 810 860 1050 1100

Up-SLICE0-V0P9_CDR3 1015 810 860 1050 1100

Up-SLICE1-V0P9_CDR3 998 810 860 1050 1100

Note 1 : For unprovisioisned slices ignore Voltage values.

Note 3 : Please contact Cisco TAC if there are any unresolved issues during this MOP

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)

Cisco NCS 1002 Upgrade MOP for R6.1.2 SMU

Available Languages

Download Options

Bias-Free Language

Upgrade Scenarios Covered in the MOP

Scenario -1 : Upgrade from 6.0.1 + k9 sec + Prod SMUs (both) to R6.1.2 with k9sec + CDR3 SMU

1. Baseline the current status by executing below command. Please log the output for reference during and after the procedure

1.1 XR Active packages:

1.2 XR committed packages:

1.3 Ncs1k-sysadmin Active packages:

1.4 Ncs1k-sysadmin committed packages

1.5 Current FPD Status:

1.6 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

2. Upgrade to 6.1.2 CCO + PROD.SMU (No traffic impact expected, 20 mins)

2.1 Software Upgrade Steps:

2.2 XR Active packages:

2.3 XR committed packages:

2.4 Ncs1k-sysadmin Active packages

2.5 Ncs1k-sysadmin committed packages

2.6 FPD Status after SU

2.7 Slice Status after SU

3. FPD Upgrade Steps

3.1 FPD Upgrade:

3.2 Reload NCS1K

4. Validate FPD and Slice Status

4.1 Verify FPD all

4.2 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

4.3 Verify environment voltages on ncs1k-sysadmin

Scenario -2 : R6.1.2 Prod SMU Installation – Only for already upgraded boxes

1. Baseline the current status by executing below command. Please log the output for reference during and after the procedure

1.1 XR Active packages:

1.2 XR committed packages:

1.3 Ncs1k-sysadmin Active packages:

1.4 Ncs1k-sysadmin committed packages

1.5 Current FPD Status:

1.6 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

2. Upgrade to 6.1.2 CCO + PROD.SMU (No traffic impact expected)

2.1 SMU Upgrade Steps:

2.2 XR Active packages:

2.3 XR committed packages:

2.4 Ncs1k-sysadmin Active packages

2.5 Ncs1k-sysadmin committed packages

2.6 FPD Status after SMU Upgrade:

2.7 Slice Status after SU

3. FPD Upgrade Steps

3.1 FPD Upgrade:

3.2 Reload NCS1K

4. Validate FPD and Slice Status

4.1 Verify FPD all

4.2 Verify “Status” is “Provisioned” and “HW status” is “Current” for all the configured slices

4.3 Verify environment voltages on ncs1k-sysadmin

Was this Document Helpful?

Contact Cisco

This Document Applies to These Products