Table Of Contents
Software Package Management Debug Commands on Cisco IOS XR Software
Software Package Management Debug Commands on Cisco IOS XR Software
This chapter describes the commands used to debug Cisco IOS XR software package management.
debug install id
To enable the display of the debug messages for the installation director, use the debug install id command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install id [chkpt | compatibility {checks | errors | parser} | config | db | ens | events | install] location node-id
no debug install id [chkpt | compatibility {checks | errors | parser} | config | db | ens | events | install] location node-id
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable installation director debugging:
RP/0/RP0/CPU0:router# debug install id location 0/1/cpu0
debug install ih
To enable the display of the debug messages for the installation helper, use the debug install ih command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install ih [clean | ens | sync | sysdb] [location node-id]
no debug install ih [clean | ens | sync | sysdb] [location node-id]
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable installation helper debugging:
RP/0/RP0/CPU0:router# debug install ih location 0/1/cpu0
debug install instcmd
To enable the display of the debug messages for executable installation commands, use the debug install instcmd command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install instcmd [location node-id]
no debug install instcmd [location node-id]
Syntax Description
location node-id
(Optional) Displays debug messages for executable installation commands for a specified location. The node-id argument is entered in the rack/slot/module notation.
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable executable installation commands debugging:
RP/0/RP0/CPU0:router# debug install instcmd location 0/1/cpu0
debug install inventory
To enable the display of the debug messages for the installed inventory commands, use the debug install inventory command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install inventory [process process-name | job jobid] [location node-id]
no debug install inventory [process process-name | job jobid] [location node-id]
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable installed inventory commands debugging:
RP/0/RP0/CPU0:router# debug install inventory location 0/1/cpu0
debug install loadpath
To enable the display of the debug messages for loadpath library, use the debug install loadpath command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install loadpath [process process-name | job jobid] [location node-id]
no debug install loadpath [process process-name | job jobid] [location node-id]
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable loadpath library debugging:
RP/0/RP0/CPU0:router# debug install loadpath location 0/1/cpu0
debug install notify
To enable the display of the debug notification messages, use the debug install notify command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install notify [blobs | callbacks | dx | lists test | notifications | payload | transid] [process process-name | job jobid] [location node-id]
no debug install notify [callbacks | dx | lists test | notifications | payload | transid] [process process-name | job jobid] [location node-id]
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable notification messages:
RP/0/RP0/CPU0:router# debug install notify location 0/1/cpu0
debug install replicator
To enable the display of the debug messages for the installation replicator code, use the debug install replicator command in EXEC mode. To disable the display of debug messages, use the no form of this command.
debug install replicator [process process-name | job jobid] [location node-id]
no debug install replicator [process process-name | job jobid] [location node-id]
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Release ModificationRelease 2.0
This command was introduced on the Cisco CRS-1.
Release 3.0
No modification.
Release 3.2
This command was supported on the Cisco XR 12000 Series Router.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of the Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to enable installation replicator code debugging:
RP/0/RP0/CPU0:router# debug install replicator location 0/1/cpu0