Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

• The networking device must be running a Cisco release that supports Flexible NetFlow.

Flow exporters are created as separate components in a router's configuration. Exporters are assigned to flow monitors to export the data from the flow monitor cache to a remote system such as a NetFlow collector. Flow monitors can support more than one exporter. Each exporter can be customized to meet the requirements of the flow monitor or monitors in which it is used and the NetFlow collector systems to which it is exporting data.

Flexible NetFlow allows you to configure many different flow exporters, depending on your requirements. Some of the benefits of Flexible NetFlow flow exporters are as follows:

• Using flow exporters, you can create an exporter for every type of traffic that you want to analyze so that you can send each type of traffic to a different NetFlow collector. Original NetFlow sends the data in a cache for all of the analyzed traffic to a maximum of two export destinations.
• Flow exporters support up to ten exporters per flow monitor. Original NetFlow is limited to only two export destinations per cache.
• Flow exporters can use both TCP and UDP for export.
• Depending on your release, flow exporters can use class of service (CoS) in the packets that are sent to export destinations to help ensure that the packets are given the correct priority throughout the network. Original NetFlow exporters do not use CoS in the packets that are sent to export destinations.
• Depending on your release, flow exporter traffic can be encrypted.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    flow exporter exporter-name

4.    description description

5.    destination {ip-address | hostname} [vrf vrf-name]

6.    export-protocol {netflow-v5 | netflow-v9 | ipfix}

7.    dscp dscp

8.    source interface-type interface-number

9.    option {exporter-stats | interface-table | sampler-table| vrf-table} [timeout seconds]

10.    output-features

11.    template data timeout seconds

12.    transport udp udp-port

13.    ttl seconds

14.    end

15.    show flow exporter exporter-name

16.    show running-config flow exporter exporter-name

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: Device> enable	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: Device# configure terminal	Enters global configuration mode.
Step 3	flow exporter exporter-name Example: Device(config)# flow exporter EXPORTER-1	Creates the flow exporter and enters Flexible NetFlow flow exporter configuration mode. This command also allows you to modify an existing flow exporter.
Step 4	description description Example: Device(config-flow-exporter)# description Exports to the datacenter	(Optional) Configures a description to the exporter that will appear in the configuration and the display of the show flow exporter command.
Step 5	destination {ip-address | hostname} [vrf vrf-name] Example: Device(config-flow-exporter)# destination 172.16.10.2	Specifies the IP address or hostname of the destination system for the exporter. Note    You can export to a destination using either an IPv4 or IPv6 address.
Step 6	export-protocol {netflow-v5 | netflow-v9 | ipfix} Example: Device(config-flow-exporter)# export-protocol netflow-v9	Specifies the version of the NetFlow export protocol used by the exporter. The export of extracted fields from NBAR is supported only over IPFIX. Default: netflow-v9.
Step 7	dscp dscp Example: Device(config-flow-exporter)# dscp 63	(Optional) Configures differentiated services code point (DSCP) parameters for datagrams sent by the exporter. The range for the dscp argument is from 0 to 63. Default: 0.
Step 8	source interface-type interface-number Example: Device(config-flow-exporter)# source ethernet 0/0	(Optional) Specifies the local interface from which the exporter will use the IP address as the source IP address for exported datagrams.
Step 9	option {exporter-stats | interface-table | sampler-table| vrf-table} [timeout seconds] Example: Device(config-flow-exporter)# option exporter-stats timeout 120	(Optional) Configures options data parameters for the exporter. You can configure all three options concurrently. The range for the seconds argument is 1 to 86,400. Default: 600.
Step 10	output-features Example: Device(config-flow-exporter)# output-features	(Optional) Enables sending export packets using quality of service (QoS) and encryption.
Step 11	template data timeout seconds Example: Device(config-flow-exporter)# template data timeout 120	(Optional) Configure resending of templates based on a timeout. The range for the seconds argument is 1 to 86400 (86400 seconds = 24 hours).
Step 12	transport udp udp-port Example: Device(config-flow-exporter)# transport udp 650	Specifies the UDP port on which the destination system is listening for exported datagrams. The range for the udp-port argument is from 1 to 65536.
Step 13	ttl seconds Example: Device(config-flow-exporter)# ttl 15	(Optional) Configures the time-to-live (TTL) value for datagrams sent by the exporter. The range for the seconds argument is from 1 to 255.
Step 14	end Example: Device(config-flow-exporter)# end	Exits flow exporter configuration mode and returns to privileged EXEC mode.
Step 15	show flow exporter exporter-name Example: Device# show flow exporter FLOW_EXPORTER-1	(Optional) Displays the current status of the specified flow exporter.
Step 16	show running-config flow exporter exporter-name Example: Device# show running-config flow exporter FLOW_EXPORTER-1	(Optional) Displays the configuration of the specified flow exporter.