Cisco Network Tasks

This chapter contains the following sections:

Activate SAN Zone Set

Summary

Activate a SAN zone set for a Nexus device.

Description

This task activates or de-activate a SAN zone set on a Nexus device. If the Activate option is enabled, then a rollback deactivates and removes the zone set from the ACTIVE list. Once the zone set is removed from the ACTIVE list, the device restarts the zone merge process. If the Disable Rollback option is selected, rollback is not permitted.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone Set	Select SAN Zone	network​SANZone​Set​Identity	Y
Activate	Select this option to activate
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SANZONE_​SET_​IDENTITY	Identity for San Zone Set.​	network​SANZone​Set​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Add IP ACL Rule

Summary

Add an IP rule to an ACL.

Description

This task adds an IP rule to an access control list (ACL) on the device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
ACL Name	ACL Name	gen_​text_​input	Y
Action	Specify permit / deny action for the rule	gen_​text_​input
Protocol	Specify protocol for the rule	gen_​text_​input
Source Type	Specify source type	gen_​text_​input
Source Network Prefix	Specify source network prefix (A.​B.​C.​D/LEN)/(X:X:X:X:X:X:X:X/LEN)	gen_​text_​input	Y
Source Network Address	Specify source network address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Source Wildcard Bits	Specify source wildcard bits (A.​B.​C.​D)[Not applicable for IPv6]	gen_​text_​input	Y
Source Host Address	Specify source host address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Destination Type	Specify destination type	gen_​text_​input
Destination Network Prefix	Specify destination network prefix (A.​B.​C.​D/LEN)/(X:X:X:X:X:X:X:X/LEN)	gen_​text_​input	Y
Destination Network Address	Specify destination network address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Destination Wildcard Bits	Specify destination wildcard bits (A.​B.​C.​D)[Not applicable for IPv6]	gen_​text_​input	Y
Destination Host Address	Specify destination host address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​ACL_​NAME	ACL on which selected operation performed.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​IP_​ACL_​NAME_​IDENTITY	ACL name ip on which selected operation performed.​	networking_​nxos_​ip_​acl_​info

Add MAC ACL Rule

Summary

Add a MAC rule to an ACL.

Description

This task adds a media access control (MAC) rule to an access control list (ACL) on the device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
ACL Name	ACL Name	gen_​text_​input	Y
Action	Specify permit / deny action for the rule	gen_​text_​input
Source Type	Specify source type	gen_​text_​input
Source MAC address	Specify source MAC address (Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE )	gen_​text_​input	Y
Source wildcard bits	Specify source wildcard bits (Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE )	gen_​text_​input	Y
Destination Type	Specify destination type	gen_​text_​input
Destination MAC address	Specify destination MAC address (Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE )	gen_​text_​input	Y
Destination wildcard bits	Specify destination wildcard bits (Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE )	gen_​text_​input	Y
VLAN ID	Select VLAN ID to be deleted	vlan​ID
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​ACL_​NAME	ACL on which selected operation performed.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​MAC_​ACL_​NAME_​IDENTITY	ACL name mac on which selected operation performed.​	networking_​nxos_​mac_​acl_​info

Add Member To SAN Zone

Summary

Add a member to a zones on a Nexus device.

Description

This task adds a member to the SAN zone on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone	Select SAN Zone	network​SANZone​Identity	Y
Type	Type Member	gen_​text_​input
Member	Value for the Member	gen_​text_​input	Y
Prefer Smart​Zoning Zone	Select this option to leverage the smart zoning feature if supproted by device and and enabled in VSAN
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​SANZONE_​MEMBER	San Zone Member Configured.​	gen_​text_​input
OUTPUT_​SANZONE_​TYPE	San Zone Type Configured.​	gen_​text_​input
OUTPUT_​SMARTZONE_​TYPE	Smart Zone Type Configured.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​SAN_​FC_​ALIAS	FC alias on which selected operation performed.​	FCAlias​Identity
OUTPUT_​SAN_​DEV_​ALIAS	Device alias on which selected operation performed.​	networking_​san_​device_​alias_​identity

Add Physical Network Account

Summary

Add a physical network account.

Description

This task adds a physical network account.

Inputs

Input	Description	Mappable To Type	Mandatory
Pod Name		gen_​text_​input	Y
Device Category	Device Category	gen_​text_​input
Device IP		gen_​text_​input	Y
Protocol		gen_​text_​input	Y
Port		gen_​text_​input	Y
Username		gen_​text_​input	Y
Password		gen_​text_​input	Y
Enable Password	Enable Password

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
DEVICE_​INVENTORY_​STATUS	Device Inventory Status	gen_​text_​input

Add SAN Zone to Zone Set

Summary

Add a SAN zone to a zone set on a Nexus device.

Description

This task adds a zone to a SAN zone set on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone Set	Select SAN Zone	network​SANZone​Set​Identity	Y
SAN Zone	Select SAN Zone	network​SANZone​Identity	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Reactivate Zoneset during Rollback	Select this option to reactivate zoneset during rollback.​
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SANZONE_​SET_​IDENTITY	Identity for San Zone Set.​	network​SANZone​Set​Identity
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Add or Update Username and Password

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
User Name	Provide User Name	gen_​text_​input	Y
Password	Provide Password	password	Y

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​USERNAME	Password Reset User Name	password_​reset_​username

Allocate Port To VDC

Summary

Allocate a physical port to a VDC.

Description

This task allocates a physical port to a virtual data channel (VDC) on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VDC Name	VDC Name.​	nxos​VDCIdentity	Y
Select Port	Select a port .​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Assign FC Port to VSAN

Summary

Assign an FC port to a VSAN.

Description

This task makes an FC (Fiber Channel) port a member of a virtual storage area network (VSAN) on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select FC Port	Select a FC port for VSAN assignment	gen_​text_​input	Y
Select FC Port	Select a FC port for VSAN assignment	fc_​port_​name
VSAN ID	Select VSAN ID to be deleted	vsan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Assign Port to Port Channel

Summary

Assign an ethernet port to a port channel.

Description

This task adds an ethernet port to a port channel on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select Port	gen_​text_​input	Y
Select Port Channel Name	Select a port channel name.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
PORT_​CHANNEL_​NAME	Port channel name	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Assign Static MACAddress

Summary

Assign a static MAC address for a layer 3 interface on a Nexus device.

Description

This task assigns a static MAC address entry for a layer 3 interface on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port.​	networking_​device_​interface	Y
MAC Address	Enter MAC Address​Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE.​	networking_​device_​mac	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface
OUTPUT_​NETWORKING_​DEVICE_​MACADDRESS	Network device MAC Address on which selected operation performed.​	networking_​device_​mac
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Assign VLAN to Group

Summary

Assign a VLAN to a UCS Director group.

Description

This task assigns a VLAN on a device to a UCS Director group.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN ID	VLAN ID/Range	vlan​ID	Y
Assign To Users	Select this option to allow resource assignment to users.​
User Group ID	Select the group to assign to VLAN.​	user​Group	Y
Comments	Enter comments	gen_​text_​input

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID

Assign VXLAN to PortProfile

Summary

Assign a VXLAN port profile to a Nexus device.

Description

This task assigns a VXLAN on the Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Bridge Name	Domain Name for VXLAN Bridge.​	gen_​text_​input	Y
Select Port Profile	Select the port profile	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name

Associate Private VLAN

Summary

Associate a private VLAN on a device.

Description

This task associates the primary and secondary VLAN on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Primary VLAN ID	Primary VLAN	vlan​ID	Y
Action	Private VLAN action		Y
Secondary VLAN ID	Secondary VLAN IDs to associate	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PRIMARY_​VLAN_​ID	Primary VLAN ID on which the selected operation was performed	vlan​ID
SECONDARY_​VLAN_​ID	Secondary VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Associate VFC Interface

Summary

Associate a VFC on a Nexus device to a VSAN.

Description

This task associates a virtual fiber channel (VFC) to a VSAN on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VFC Id	VFC ID to be associated.​	gen_​text_​input	Y
VSAN Id	VSAN ID to be associated.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Associate VSAN to VLAN

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Vlan	Vlan ID to be associated.​	vlan​ID	Y
VSAN Id	VSAN ID to be associated.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​DEVICE_​VLAN_​IDENTITY	Identity for device vlan	Infra​Network​VLANIdentity
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Clear SAN Zone Lock

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select a Networking device	networking_​device	Y
VSAN ID	Select a VSAN id to clear the lock	vsan​ID	Y
Copy Running configuration to Startup configuration	Check this option to copy running configuration to startup configuration.​ By default, this field is checked

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure Access

Summary

Configure access on an ethernet or port channel interface.

Description

This task configures access on an ethernet or port channel interface on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port name.​	networking_​device_​interface	Y
Access VLAN	Select list of VLAN to be allowed in Access mode	vlan​ID	Y
STP Port Type	Specify a port type for spanning tree protocol use	gen_​text_​input
Description	Enter description for this Configure Access	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
ACCESS_​VLAN_​ID	Access VLAN ID on which the selected operation was performed	gen_​text_​input
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface

Configure Feature

Summary

Configure a feature on a Nexus MDS device.

Description

This task configures a feature on a Cisco Multilayer Director (MDS) device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Feature	Enable / Disable the feature.​		Y
Feature Name	Feature Name to be confgiures.​	networking_​device_​feature	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure Host Name

Summary

Configure a host name on a Nexus device.

Description

This task configures a host name on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Host Name	Host Name	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
HOST_​NAME	Host Name on which the selected operation was performed	networking_​device_​host_​name
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure MACAddress Table

Summary

Configure MAC address table parameters.

Description

This task configures the MAC address table parameters, including aging time and learning mode.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Age Time	Agent time for the mac address table in seconds.​	gen_​text_​input	Y
VLAN ID	VLAN ID	Infra​Network​VLANIdentity
VLAN Learn mode.​	Select a learning mode for the vlans .​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure MST

Summary

Configure the MST mode of the spanning tree protocol for a Nexus device.

Description

This task configures multiple spanning tree (MST) mode for the spanning tree protocol on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Enable MST	Enable / Disable the Spanning tree MST mode.​		Y
Name	Specify MST Name to configure.​	gen_​text_​input	Y
Revision	Specify Revision for the MST.​	gen_​text_​input	Y
Hello Time	Specify Hello Time for the MST protocol.​	gen_​text_​input
Forward Time	Specify Forward Time for the mst.​	gen_​text_​input
Max Hop Count	Specify max hop count for the mst.​	gen_​text_​input
Max Age in seconds	Specify max age for the mst.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure MST INSTANCE

Summary

Configure the MST Instance for the STP on a Nexus device.

Description

This task configures multiple spanning tree (MST) mode on an interface for the spanning tree protocol configuration on a PORT.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
MST Instance	Specify MST instance id to configure.​	gen_​text_​input	Y
VLAN	Specify VLAN ID / Range.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure PVST

Summary

Configure the PVST mode of the spanning tree protocol for a Nexus device.

Description

This task configures per VLAN spanning tree (PVST) mode for the spanning tree protocol.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Enable PVST	Enable / Disable the Spanning tree PVST mode.​		Y
VLAN	VLAN ID / Range.​	gen_​text_​input
PVST Root Mode	Enable / Disable the Spanning tree PVST in Root mode.​		Y
PVST Root Mode Primary	Enable / Disable the Spanning tree PVST in Root mode as Primary.​		Y
Diameter	Maximum number of bridges between any two end nodes(2-7).​	gen_​text_​input
Hello Time	(1-10) Number of seconds between generation of config bpdu.​	gen_​text_​input
Priority	Priority for the PVST protocol.​	gen_​text_​input
Path​Cost.​	Path Cost for the PVST.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure Port

Summary

Configure a Port on a Nexus device.

Description

This task configures a port on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port .​	gen_​text_​input	Y
Description	Provide Description.​	gen_​text_​input
Enable	To enable or disable the port
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface

Configure Port License

Summary

Configure a port license for an MDS device.

Description

This task configures a port license for a Nexus multilayer director (MDS) device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port .​	gen_​text_​input	Y
Acquire	Select this option to Acquire the license
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Configure Private VLAN Port

Summary

Configure a port with private VLANs.

Description

This task configures a port with a primary and secondary private VLAN.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port to configure Private VLAN.​	gen_​text_​input	Y
Type	Private VLAN Port Type		Y
Primary VLAN ID	Primary VLAN	vlan​ID	Y
Action	Private VLAN action		Y
Secondary VLAN ID	Secondary VLAN IDs to associate	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure Private VLAN Port Profile

Summary

Configure a port profile with private VLANs.

Description

This task modifies a port profile with private primary and secondary VLANs configured on it.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Profile Name	Port Profile to create	gen_​text_​input	Y
Port Profile Type	Port profile Type		Y
Trunk	Create Port Profile in trunk mode
Private VLAN Type	Private VLAN Port Type		Y
Primary VLAN ID	Primary VLAN	vlan​ID	Y
Action	Private VLAN action
Secondary VLAN ID	Secondary VLAN IDs to associate	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure QOS on Nexus 1K

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Integrate with UCS QOS Policy	Select this option to integrate with UCS QOS System class policy
UCS Account Name	Select UCS Account Name	ucs​Account​Name	Y
Configure Platinum Class	Select this option to configure platinum class parameters
Platinum Class ACL Name	Select ACLs for classifying platinum class triffic	gen_​text_​input	Y
Platinum Class COS	Select COS level	gen_​text_​input
Configure Gold Class	Select this option to configure gold class parameters
Gold Class ACL Name	Select ACLs for classifying gold class triffic	gen_​text_​input	Y
Gold Class COS	Select COS level	gen_​text_​input
Configure Silver Class	Select this option to configure silver class parameters
Silver Class ACL Name	Select ACLs for classifying silver class triffic	gen_​text_​input	Y
Silver Class COS	Select COS level	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
Request Approval	Select this option to request for approval to deliver commands to device

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Configure QOS on Nexus 5K

Summary

Configure QOS policies on a Nexus 5k switch.

Description

This task configures quality of service (QOS) policies on a Nexus 5000 series switch.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Integrate with UCS QOS Policy	Select this option to integrate with UCS QOS System class policy
UCS Account Name	Select UCS Account Name	ucs​Account​Name	Y
Configure Platinum Class	Select this option to configure platinum class parameters
Platinum Class ACL Name	Select ACLs for classifying platinum class triffic	gen_​text_​input	Y
Platinum Class QOS Group	Select QOS group	gen_​text_​input
Platinum Class COS	Select COS level	gen_​text_​input
Platinum Class MTU	Enter MTU value	vlan​ID	Y
Configure Gold Class	Select this option to configure gold class parameters
Gold Class ACL Name	Select ACLs for classifying gold class triffic	gen_​text_​input	Y
Gold Class QOS Group	Select QOS group	gen_​text_​input
Gold Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Gold Class COS	Select COS level	gen_​text_​input
Gold Class MTU	Enter MTU value	vlan​ID	Y
Configure Silver Class	Select this option to configure silver class parameters
Silver Class ACL Name	Select ACLs for classifying silver class triffic	gen_​text_​input	Y
Silver Class QOS Group	Select QOS group	gen_​text_​input
Silver Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Silver Class COS	Select COS level	gen_​text_​input
Silver Class MTU	Enter MTU value	vlan​ID	Y
Configure FC Class	Select this option to configure FC class parameters
FC Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Configure Default Class	Select this option to configure default class parameters
Defualt Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
Request Approval	Select this option to request for approval to deliver commands to device

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Configure QOS on Nexus 9K

Summary

Configure QOS policies on a Nexus 9K switch.

Description

This task configures quality of service (QOS) policies on a Nexus 9000 series switch.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Integrate with UCS QOS Policy	Select this option to integrate with UCS QOS System class policy
UCS Account Name	Select UCS Account Name	ucs​Account​Name	Y
Configure Platinum Class	Select this option to configure platinum class parameters
Platinum Class ACL Name	Select ACLs for classifying platinum class triffic	gen_​text_​input	Y
Platinum Class QOS Group	Select QOS group	gen_​text_​input
Platinum Class COS	Select COS level	gen_​text_​input
Platinum Class MTU	Enter MTU value	vlan​ID	Y
Configure Gold Class	Select this option to configure gold class parameters
Gold Class ACL Name	Select ACLs for classifying gold class triffic	gen_​text_​input	Y
Gold Class QOS Group	Select QOS group	gen_​text_​input
Gold Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Gold Class COS	Select COS level	gen_​text_​input
Gold Class MTU	Enter MTU value	vlan​ID	Y
Configure Silver Class	Select this option to configure silver class parameters
Silver Class ACL Name	Select ACLs for classifying silver class triffic	gen_​text_​input	Y
Silver Class QOS Group	Select QOS group	gen_​text_​input
Silver Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Silver Class COS	Select COS level	gen_​text_​input
Silver Class MTU	Enter MTU value	vlan​ID	Y
Configure Default Class	Select this option to configure default class parameters
Defualt Class BW Percentage	Select BW Percentage	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
Request Approval	Select this option to request for approval to deliver commands to device

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Configure Retention Setting

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Retention Period Value	Provide Retention Period Value Like 1,2,3.​.​.​	gen_​text_​input
Retention Period Unit	Select Retention Period Unit	gen_​text_​input

Outputs

Output	Description	Type
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​PURGE_​SETTING_​DURATION	Purge setting duration	gen_​text_​input
OUTPUT_​PURGE_​SETTING_​FREQUENCY	Purge setting duration	gen_​text_​input

Configure SAN Zoning

Summary

Configure SAN zones and associate zones with zonesets.

Description

This task configures zones with UCS vHBA and NetApp Fiber Channel adapters as members and then associate the zones with the active zoneset. If there is no active zoneset available on the switch, the task creates a new zoneset and actives it.

Inputs

Input	Description	Mappable To Type	Mandatory
Activate Zone Set	activate the zone set after creation
Commit Zone	Commit the San Zone after creation.​
Server Account Type	Specify the server type	gen_​text_​input
Service Profile	Select Service Profile	ucs​Service​Profile​Identity	Y
CIMC Server	Select CIMC Server	cimc​Server​Identity	Y
Select v​HBA	Select v​HBA for Fabric A configuration	gen_​text_​input	Y
Device Alias Fab A v​HBA	Device Alias name for the v​HBA.​	gen_​text_​input
VLAN ID	VLAN ID	vlan​ID
VSAN ID	VSAN ID	gen_​text_​input
Zone Name	Zone A Name	gen_​text_​input
Net​App Account Name (Primary)	Select primary Net​App account for Fabric A configuration	Cluster​Filer​Identity	Y
Net​App FC Adapter (Primary)	Select primary Net​App Fiber Channel Adapter for Fabric A configuration	gen_​text_​input	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Configure Secondary Head	Select this option to configure secondary head
Net​App Account Name (Secondary)	Select secondary Net​App account for Fabric A configuration	Cluster​Filer​Identity	Y
Net​App FC Adapter (Secondary)	Select secondary Net​App Fiber Channel Adapter for Fabric A configuration	gen_​text_​input	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Select Device	Select device for Fabric A configuration	gen_​text_​input	Y
Select Source Port	Select a source port to which server is connected.​	gen_​text_​input	Y
Select Mapping VSAN	Select a VSAN to map the VLAN.​	gen_​text_​input	Y
Configure Fabric B	Select this option to configure zones for Fabric B
Select v​HBA	Select v​HBA for Fabric B configuration	gen_​text_​input	Y
Device Alias Fab B v​HBA	Device Alias name for the v​HBA.​	gen_​text_​input
VLAN ID	VLAN ID	vlan​ID
VSAN ID	VSAN ID	gen_​text_​input
Zone Name	Zone B Name	gen_​text_​input
Net​App Account Name (Primary)	Select primary Net​App account for Fabric B configuration	Cluster​Filer​Identity	Y
Net​App FC Adapter (Primary)	Select primary Net​App Fiber Channel Adapter for Fabric B configuration	Cluster​Filer​Identity	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Configure Secondary Head	Select this option to configure secondary head
Net​App Account Name (Secondary)	Select secondary Net​App account for Fabric B configuration	Cluster​Filer​Identity	Y
Net​App FC Adapter (Secondary)	Select secondary Net​App Fiber Channel Adapter for Fabric B configuration	Cluster​Filer​Identity	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if muliple fc adapter.​	gen_​text_​input
Select Device	Select device for Fabric B configuration	gen_​text_​input	Y
Select Source Port	Select a source port to which server is connected.​	gen_​text_​input	Y
Select Mapping VSAN	Select a VSAN to map the VLAN.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
FABRIC_​A_​ZONESET_​NAME	Name of the zoneset on which the selected operation was performed for fabric A	gen_​text_​input
FABRIC_​A_​ZONE_​NAME	Name of the zone that was created for fabric A	gen_​text_​input
FABRIC_​A_​DEVICE_​IP	Switch IP Address (Fabric A)	networking_​device
FABRIC_​A_​VSAN_​ID	VSAN ID on which the selected operation was performed	gen_​text_​input
SAN_​ZONE_​A_​IDENTITY	Identity for SAN Zone A	gen_​text_​input
FABRIC_​A_​VDC_​NAME	VDC Name (Fabric A)	nxos​VDCIdentity
FABRIC_​B_​ZONESET_​NAME	Name of the zoneset on which the selected operation was performed for fabric B	gen_​text_​input
FABRIC_​B_​ZONE_​NAME	Name of the zone that was created for fabric B	gen_​text_​input
FABRIC_​B_​DEVICE_​IP	Switch IP Address (Fabric B)	networking_​device
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
FABRIC_​B_​VSAN_​ID	VSAN ID on which the selected operation was performed	gen_​text_​input
SAN_​ZONE_​B_​IDENTITY	Identity for SAN Zone B	gen_​text_​input
FABRIC_​B_​VDC_​NAME	VDC Name (Fabric B)	nxos​VDCIdentity

Configure STP PORT

Summary

Configure PVST on an interface for the STP on a Nexus device.

Description

This task configures per VLAN spanning tree (PVST) on an interface for the spanning tree protocol configuration on a PORT.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port.​	networking_​device_​interface	Y
VLAN	VLAN ID / Range.​	gen_​text_​input
Cost Auto	Auto cost for the STP Port
Cost	Cost value (1-200000000).​	gen_​text_​input
Hello Time	(1-10) Number of seconds between generation of config bpdu.​	gen_​text_​input
Forward Time	(4-30) Number of seconds for the forward delay timer	gen_​text_​input
Max Age	(6-40) Maximum number of seconds the information in a bpdu is valid.​	gen_​text_​input
Link Type.​	Link Type for the PVST.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NET_​DEVICE_​INTERFACE_​IDENTITY	Identity for network interface.​	Infra​Network​Interface​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure Session Pool Properties

Summary

Configure session pool properties.

Description

This task configures session pool properties such as maximum active session and maximum wait time.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Maximum Active Sessions	Provide the Maximum Active Device Sessions
Maximum Wait Time	Provide the Maximum Wait Time

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​MAX_​ACTIVE_​SESSION	Identity for Maximum Active Session.​	gen_​text_​input
OUTPUT_​WAIT_​TIME	Identity for Maximum Wait Time.​	gen_​text_​input

Configure Smart Call Home Contact Information

Summary

Configure Smart Call Home contact information on a Nexus device.

Description

This task configures Smart Call Home contact information on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SNMP sys​Contact	SNMP sys​Contact	gen_​text_​input	Y
Email Contact	Email Contact	email_​address_​list	Y
International Phone Number	International Phone Number	gen_​text_​input	Y
Street Address	Street Address	gen_​text_​input	Y
Contract Number	Contract Number	gen_​text_​input
Customer Number	Customer Number	gen_​text_​input
Site Number	Site Number	gen_​text_​input
Switch Priority Number	Switch Priority Number	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
Commit	Commit

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SYS_​CONTACT	SNMP sys​Contact.​	gen_​text_​input

Configure System Level HA

Summary

Configure system level HA on a Nexus 1oooV device.

Description

This task configures system level HA on a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Role	HA Supervisor Role	gen_​text_​input	Y
System Switchover	Manual Switchover
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​HA_​ROLE	The High Availability Role that was configured.​	nexus_​vdc

Configure Trunk

Summary

Configure a trunk on an ethernet or port channel interface.

Description

This task configures a trunk on an ethernet or port channel interface on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Name	Select a port name	networking_​device_​interface	Y
Description	Provide Description for the Configure Trunk	gen_​text_​input
Native VLAN ID	Select VLAN ID to be deleted	vlan​ID	Y
Allowed VLANs	Select list of VLAN to be allowed in trunk mode	gen_​text_​input	Y
STP Port Type	Specify a port type for spanning tree protocol use	gen_​text_​input
MTU	Provide MTU range between (1500-9216)	gen_​text_​input
Select Port Channel	Select a port channel.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
Force VLAN	Select this option to Force VLAN	Boolean

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
NATIVE_​VLAN_​ID	Native VLAN ID on which the selected operation was performed	gen_​text_​input
ALLOWED_​VLAN_​IDS	Allowed VLAN IDsf on which the selected operation was performed	gen_​text_​input
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface
OUTPUT_​NET_​DEVICE_​INTERFACE_​IDENTITY	Identity for network interface.​	Infra​Network​Interface​Identity

Configure VPC Domain

Summary

Configure a VPC domain.

Description

This task configures a virtual port channel (VPC) domain on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Domain ID	Domain ID	gen_​text_​input	Y
Source Management IP Address	Source Management IP Address	ipaddress	Y
Destination Management IP Address	Destination Management IP Address	ipaddress	Y
Role Priority	Role Priority	gen_​text_​input	Y
System Priority	System Priority	gen_​text_​input
Delay Restore	Provide the Delay Restore rabge between (1-3600)	gen_​text_​input
Peer Gateway	Select this option to provide peer gateway	Boolean
Auto Recovery	Select this option to auto-recovery	Boolean
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration	Boolean

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VPC_​DOMAIN_​ID	VPC Domain ID	gen_​text_​input
SOURCE_​MANAGEMENT_​IP	Source management IP address on which selected operation was performed.​	gen_​text_​input
DESTINATION_​MANAGEMENT_​IP	Destination management IP address on which selected operation was performed.​	gen_​text_​input
VPC_​DOMAIN_​ROLE_​PRIORITY	Role priority of VPC domain on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure VPC PortChannel

Summary

Configure a vPC in a Nexus device.

Description

This task configures a vitual port channel (vPC) in a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Channel Name	Select a port channel name.​	Infra​Network​Interface​Identity	Y
VPC Peer​Link	Select this option Configure port channel as VPC Peer Link
Enter Domain Id	Enter Domain Id.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​NET_​DEVICE_​VPC_​INTERFACE_​IDENTITY	VPC Interface Configured.​	networking_​device_​vpc_​interface

Configure VTP

Summary

Configure the VTP for a Nexus device.

Description

This task configures the VLAN trunking protocol (VTP) for a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Enable VTP Feature	Enable / Disable the VTP feature.​		Y
Domain Name	Domain Name for the VTP protocol.​	gen_​text_​input
VTP Version.​	Select a VTP version to configure.​	gen_​text_​input
File Name	File Name for the VTP protocol.​	gen_​text_​input
Password	Password for the VTP protocol.​	gen_​text_​input
VTP mode.​	Select a learning mode for the vlans .​	gen_​text_​input
Pruning	Pruning for the VTP.​
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Configure VXLAN Range

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Configure VXLAN	Select this option to set the Configure VXLAN	Boolean
VXLAN Id	Vx​LAN ID to be updated.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VXLAN_​ID	VXLAN ID on which the selected operation was performed	vlan​ID

Convert To Smart Zone

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Type	Type	gen_​text_​input	Y
VSAN Id	VSAN ID to be associated.​	gen_​text_​input	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
SAN_​ZONE_​NAME	SAN Zone Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Copy Running To Startup Configuration

Summary

Copies the running configuration to the startup configuration.

Description

This task copies the device's running configuration to its startup configuration. This task can be used as last task of network configuration workflow and make the configuration changes permanent to the device flash.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y

Outputs

No Outputs

Create ACL Entry

Summary

Create an ACL entry.

Description

This task creates an ACL entry.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
ACL Name	ACL Name	gen_​text_​input	Y
Type	Specify ACL entry type	gen_​text_​input
Action	Specify permit / deny action for the rule	gen_​text_​input
Protocol	Specify protocol for the rule	gen_​text_​input
Source Type	Specify source type	gen_​text_​input
Source Network Prefix	Specify source network prefix (A.​B.​C.​D/LEN)/(X:X:X:X:X:X:X:X/LEN)	gen_​text_​input	Y
Source Network Address	Specify source network address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Source Wildcard Bits	Specify source wildcard bits (A.​B.​C.​D)[Not applicable for IPv6]	gen_​text_​input	Y
Source Host Address	Specify source host address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Destination Type	Specify destination type	gen_​text_​input
Destination Network Prefix	Specify destination network prefix (A.​B.​C.​D/LEN)/(X:X:X:X:X:X:X:X/LEN)	gen_​text_​input	Y
Destination Network Address	Specify destination network address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Destination Wildcard Bits	Specify destination wildcard bits (A.​B.​C.​D)[Not applicable for IPv6]	gen_​text_​input	Y
Destination Host Address	Specify destination host address (A.​B.​C.​D)/(X:X:X:X:X:X:X:X)	gen_​text_​input	Y
Description	Enter description for this ACL entry	gen_​text_​input
Per ACL Entry stats collection	Select this option to collect stats for each ACL entry
Apply ACL to interface	Apply ACL to interfac
Select Interface	Select Interface	networking_​device_​interface
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​ACL_​NAME	ACL on which selected operation performed.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create Device Alias

Summary

Create a device alias.

Description

This task creates a device alias on a device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Device Alias Name	Device Alias Name	gen_​text_​input	Y
Enter port WWN	[hh:hh:hh:hh:hh:hh:hh:hh] Enter port WWN	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​SAN_​DEV_​ALIAS	Device alias on which selected operation performed.​	networking_​san_​device_​alias_​identity
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SANZONE_​MEMBER	San Zone Member Configured.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create Device FCAlias

Summary

Create a device fcAlias.

Description

This task creates a fiber channel alias on a device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
FC Alias Name	FC Alias Name	gen_​text_​input	Y
VSAN Id	VSAN ID	vsan​ID	Y
Member Type	Type Member	networking_​device_​member_​type	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​SAN_​FC_​ALIAS	FC alias on which selected operation performed.​	FCAlias​Identity

Create HSRP

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Interface Name	Select Interface Name for HSRP Configuration.​	Infra​Network​Interface​Identity	Y
Description	Provide Description for the selected Interface	gen_​text_​input
Enable Interface	Enable Interface.​
Interface IP Address	Interface IP Address in Format i.​i.​i.​i.​	ipaddress
IP Network Mask	IP network mask in format m.​m.​m.​m	ipaddress
HSRP Group Number	HSRP Group Number.​	gen_​text_​input	Y
Authentication Text	Authentication Text.​	password
Min Preempt Delay Time	Min Preempt Delay Time.​	gen_​text_​input
Priority	Priority.​	gen_​text_​input
Set Threshold	If selected, given threshold values will set otherwise default threshold values will be set i.​e.​, lower :1 , upper : priority.​	Boolean
Lower Threshhold Time	Lower Threshhold Time.​	gen_​text_​input
Upper Threshhold Time	Upper Threshhold Time.​	gen_​text_​input
Hello Interval	Hello Interval.​	gen_​text_​input
Hold Time Interval	Hold Time Interval.​	gen_​text_​input
Virtual IP Address	Virtual IP Address in Format i.​i.​i.​i.​	ipaddress
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​INTERFACE_​NAME	The Interface Name set on the device.​	gen_​text_​input
OUTPUT_​NET_​DEVICE_​INTERFACE_​IDENTITY	Identity for network interface.​	Infra​Network​Interface​Identity
OUTPUT_​DESCRIPTION	The Interface Description set on the device.​	gen_​text_​input
OUTPUT_​IS_​ENABLE_​INTERFACE	The Interface is enabled on the device.​	gen_​text_​input
OUTPUT_​INTERFACE_​IP	The Interface IP Address set on the device.​	gen_​text_​input
OUTPUT_​GROUP_​NUMBER	The HSRP Group Number set on the device.​	gen_​text_​input
OUTPUT_​HSRP_​GROUP_​NUMBER_​IDENTITY	The HSRP Group Number Identity.​	HSRPGroup​Number​Identity
OUTPUT_​AUTHENTICATION_​TEXT	The Authentication Text set on the device.​	password
OUTPUT_​PRIORITY	The Priority set on the device.​	gen_​text_​input
OUTPUT_​MIN_​PREEMPT_​DELAY_​TIME	The Min Preempt Delay Time set on the device.​	gen_​text_​input
OUTPUT_​LOWER_​THRESHHOLD_​PERIOD	The Lower Threshhold Period set on the device.​	gen_​text_​input
OUTPUT_​UPPER_​THRESHHOLD_​PERIOD	The Upper Threshhold Period set on the device.​	gen_​text_​input
OUTPUT_​HELLO_​INTERVAL	The Hello Interval set on the device.​	gen_​text_​input
OUTPUT_​HOLD_​INTERVAL	The Hold Interval set on the device.​	gen_​text_​input
OUTPUT_​VIRTUAL_​IP	The Virtual IP Address set on the device.​	gen_​text_​input

Create IP Pool Template

Summary

Create an IP pool template on a Nexus 1000V device.

Description

This task creates an IP pool template on a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
IP Pool Template Name	Provide Ip Pool Template Name	gen_​text_​input	Y
Description	Provide Description	gen_​text_​input
IP Address From Range	Provide Ip Address From Range	ipaddress	Y
IP Address To Range	Provide Ip Address To Range	ipaddress	Y
Network Address	Provide Network Address	ipaddress	Y
Network Subnet Mask	Provide Network Subnet Mask	ipaddress	Y
Default Router	Provide Default Router	ipaddress
DNS Server	Provide DNS Server	ipaddress
DNS Suffix	Provide DNS Suffix	gen_​text_​input
Netbios Name Server	Provide Netbios Name Server	ipaddress
Netbios	Net​Bios	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​IP_​POOL_​TEMPLATE	IP Pool Template	gen_​text_​input
HYPERV_​N1K_​IP_​POOL_​TEMPLATE_​IDENTITY	IP Pool Template Identity	Infra​Network​IPPool​Template​Identity

Create Logical Network

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Logical Network Name	Provide Logical Network Name	gen_​text_​input	Y
Logical Network Description	Provide Logical Network Description	gen_​text_​input
No Mode Isolation	Select this option to configure HNV Logical Network
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​LOGICALNETWORK	Logical Network	gen_​text_​input
HYPERV_​N1K_​LOGICALNETWORK_​IDENTITY	Logical Network Identity	hyperv_​n1k_​logical_​network_​identity
HYPERV_​LOGICAL_​NETWORK_​IDENTITY	Hyper​V Logical Network Identity	hyperv​Logical​Network​Identity

Create N1K HyperV Port Profile

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Profile Name	Provide Port Profile Name	gen_​text_​input	Y
Description	Provide Port Profile Description	gen_​text_​input
Port Profile Type	Provide Port Profile Type	networking_​device_​port_​profile_​type	Y
Channel Group Mode	Select Mode to Configure Ports and Channels	gen_​text_​input
Sub Group Type	Select Sub Group Type	gen_​text_​input
Publish Port Profile	Select to Publish VEthernet Port Profile	gen_​text_​input
Publish Port Profile Name	Select to Publish VEthernet Port Profile Name	gen_​text_​input
Mode	Select Mode Type as Trunk or Access	networking_​device_​port_​profile_​mode
Enable VXLAN Capability	Enable / Disable the VXLAN Capability.​	Boolean
Access VLAN	Select VLAN	vlan​ID	Y
Allowed VLANs	Select list of VLAN to be allowed in trunk mode	vlan​ID	Y
Add to System VLAN	Select this option to add the selected VLANs to System VLAN
System VLANs	Select list of Allowed VLANs to be added to system VLAN	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
VLAN_​ID_​LIST	VLAN IDs on which the selected operation was performed	vlan​ID
HYPERV_​PORT_​PROFILE_​IDENTITY	Hyper​V Port Profile Identity	hyperv​Vna​Port​Profile​Identity

Create N7K VDC

Summary

Create a VDC for a Nexus 7000 device.

Description

This task creates a virtual device context (VDC) for a Nexus 7000 device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VDC Name	VDC Name.​	gen_​text_​input	Y
Module Type	Module Type	gen_​text_​input
HA Policy	To enable High Availability Policy
Select Type	Select a HA Type .​	gen_​text_​input	Y
Select HA Policy Action	Select a HA Action .​	gen_​text_​input	Y
VDC Number	VDC Number.​	gen_​text_​input
VDC password	VDC Password.​	password	Y
VDC Template Name	VDC Template Name.​	gen_​text_​input
Select VDC Type	Select a VDC Type .​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create Network Segment

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Segement Name	Provide Network Segment Name	gen_​text_​input	Y
Network Segment Description	Provide Network Segment Description	gen_​text_​input
Network Segment Type	Specify Ethernet/Vethernet	gen_​text_​input
IP Address / Subnet	Provide IP Address / Subnet	gen_​text_​input
IP Pool Template Name	Provide IP Pool Template Name	Infra​Network​IPPool​Template​Identity
Network Segment Pool Name	Provide Network Segment Pool Name	hyperv_​n1k_​network_​segment_​pool_​identity
Tenant VRF Name	Tenant VRF Name	hyperv_​n1k_​tenant_​vrf_​identity
System Network Segment	Select this option to enable system network segment
Type	Specify VLAN/PVLAN	gen_​text_​input	Y
Vlan	Provide Vlan ID	vlan​ID
Segement ID	Provide Segment ID	gen_​text_​input
Private VLAN Type	Specify Primary/Secondary	gen_​text_​input
Secondary VLAN Type	Specify Host/Promiscuous	gen_​text_​input
Host Type	Specify Community/Isolated	gen_​text_​input
Primary VLAN	Provide Primary VLAN	vlan​ID
Secondary VLAN	Provide Secondary VLAN	vlan​ID
Publish Network Segment
Publish Network Segment Name		gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​SEGMENT	Network Segment	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​IDENTITY	Network Segment Identity	hyperv_​n1k_​network_​segment_​identity
HYPERV_​N1K_​IP_​POOL_​TEMPLATE	IP Pool Template	gen_​text_​input
HYPERV_​N1K_​IP_​POOL_​TEMPLATE_​IDENTITY	IP Pool Template Identity	Infra​Network​IPPool​Template​Identity
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL	Network Segment Pool	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​DEVICE_​VLAN_​IDENTITY	Identity for device vlan	Infra​Network​VLANIdentity
PRIMARY_​VLAN_​ID	Primary VLAN ID on which the selected operation was performed	vlan​ID
SECONDARY_​VLAN_​ID	Secondary VLAN ID on which the selected operation was performed	vlan​ID
HYPERV_​LOGICAL_​NETWORK_​IDENTITY	Hyper​V Logical Network Identity	hyperv​Logical​Network​Identity
HYPERV_​LOGICALNETWORK_​DEF_​IDENTITY	Hyper​V Network Segment Pool Identity	hyperv​Logical​Network​Def​Identity
HYPERV_​IP_​POOL_​IDENTITY	Hyper​V IP Pool Template Identity	hyperv​Ip​Pool​Identity
HYPERV_​VM_​NETWORK_​IDENTITY	Hyper​V VM Network Identity	hyperv​VMNetwork​Identity

Create Network Segment Pool

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Segment Pool Name	Provide Network Segment Pool Name	gen_​text_​input	Y
Logical Network Name	Provide Logical Network Name	hyperv_​n1k_​logical_​network_​identity
Segment Type	Specify VLAN/VXLAN/HNV Segment Types	gen_​text_​input
Multicast IP	Provide Multicast IP	ipaddress
Intra Port Communication	Select for enabling Intra Port Communication
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​LOGICALNETWORK	Logical Network	gen_​text_​input
HYPERV_​N1K_​LOGICALNETWORK_​IDENTITY	Logical Network Identity	hyperv_​n1k_​logical_​network_​identity
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL	Network Segment Pool	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity

Create Port Channel

Summary

Create a port channel.

Description

This task creates a port channel on network device and adds a description to it.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Channel Number	Port Channel Number	gen_​text_​input	Y
Description	Enter description for this port channel	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​CHANNEL_​ID	Port channel number	gen_​text_​input
PORT_​CHANNEL_​NAME	Port channel name	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface

Create Port Profile

Summary

Create a port profile on a Nexus device.

Description

This task creates and enables a port profile on a Nexus device. The port profile is available as a distributed port group on vCenter if there is a connection between the VSM and vCenter.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Profile Name	Enter name for port profile	gen_​text_​input	Y
Description	Enter description for this port profile	gen_​text_​input
Type	Select the type of port profile	networking_​device_​port_​profile_​type
Mode	Select the mode of port profile	networking_​device_​port_​profile_​mode
Enable VXLAN Capability	Enable / Disable the VXLAN Capability.​
IP address	IP address in format i.​i.​i.​i	ipaddress
IP network mask	IP network mask in format m.​m.​m.​m	ipaddress
IP next-hop address	IP next-hop address in format i.​i.​i.​i	ipaddress
Access VLAN	Select VLAN	vlan​ID	Y
Allowed VLANs	Select list of VLAN to be allowed in trunk mode	vlan​ID	Y
QOS Policy Map	Select input QOS policy map	gen_​text_​input
Add to System VLAN	Select this option to add the selected VLANs to System VLAN
System VLANs	Select list of Allowed VLANs to be added to system VLAN	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
VLAN_​ID_​LIST	VLAN IDs on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​NAME	Network device name on which selected operation is performed.​	networking_​device_​name
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​SGT_​IDENTITY	SGT Identity.​	security​Grouptag​ID
PORT_​PROFILE_​TYPE	Name of the port profile type	networking_​device_​port_​profile_​type
PORT_​PROFILE_​MODE	Name of the port profile mode	networking_​device_​port_​profile_​mode

Create Private VLAN

Summary

Create a private VLAN on a Nexus device.

Description

This task creates a primary or secondary private VLAN on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN ID	VLAN ID/Range	vlan​ID	Y
Private VLAN Type	Private VLAN Type		Y
Overwrite Existing Private VLAN	Select this option to overwrite any existing Private VLAN configuration
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create SAN Zone

Summary

Create a SAN zone on a Nexus device to VSAN.

Description

This task creates a SAN zone on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Zone Name	Zone Name	gen_​text_​input	Y
VSAN Id	VSAN ID to be associated.​	gen_​text_​input	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
SAN_​ZONE_​NAME	SAN Zone Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create SAN Zone Set

Summary

Create a SAN zone set on a Nexus device to VSAN.

Description

This task creates a SAN zone set on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Zone Set Name	Zone Name	gen_​text_​input	Y
VSAN Id	VSAN ID to be associated.​	gen_​text_​input	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
SAN_​ZONE_​SET_​NAME	SAN Zone Set Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​SANZONE_​SET_​IDENTITY	Identity for San Zone Set.​	network​SANZone​Set​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create SVI

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN Interface Number	VLAN Interface Number	gen_​text_​input	Y
IP Address	Eg: IPv4/Subnet 10.​10.​10.​0/255.​255.​255.​0,20.​20.​20.​0/8 or IPv6/Subnet X:X:X:X::X/(0-128),Y:Y::/(0-128),Z:Z:Z:Z:Z:Z:Z:Z/(0-128)	gen_​text_​input
Description	Provide Description	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VLAN_​INTERFACE_​NUMBER	VLAN Interface Number on which the selected operation was performed	gen_​text_​input
OUTPUT_​NET_​DEVICE_​INTERFACE_​IDENTITY	Identity for network interface.​	Infra​Network​Interface​Identity
OUTPUT_​DESCRIPTION	The Interface Description set on the device.​	gen_​text_​input

Create SXP Connection Peer

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Enable Device Tracking	Enable Device Tracking.​
Delete Hold Period	Delete Hold Timer Period.​	gen_​text_​input
Enable SXP	Enable SXP.​
Default Source IP Address	Default SXP Connection Peer Source IP Address in Format i.​i.​i.​i.​	ipaddress
Default Password	Default Password.​	password
Peer IP Address	SXP Connection Peer IP Address in Format i.​i.​i.​i.​	ipaddress	Y
Source IP Address	SXP Connection Peer Source IP Address in Format i.​i.​i.​i.​	ipaddress
Password Option	Password Option	gen_​text_​input	Y
Required Password	Required Password.​	password	Y
Mode	Mode	gen_​text_​input	Y
VRF	VRF	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​ISDEVICE_​TRACKING_​ENABLE	The Device Tracking enabled on the device.​	gen_​text_​input
OUTPUT_​DELETE_​HOLD_​PERIOD	The Delete Hold Timer set on the device.​	gen_​text_​input
OUTPUT_​ISSXP_​ENABLE	The SXP is enabled on the device.​	gen_​text_​input
OUTPUT_​DEFAULT_​SOURCE_​IP	The Default Source IP created on the device.​	ipaddress
OUTPUT_​DEFAULT_​PASSWORD	The Default Password created on the device.​	password
OUTPUT_​PEER_​IP	The Peer IP created on device.​	ipaddress
OUTPUT_​SXP_​CONNECTION_​PEER_​IDENTITY	The SXP Connection Peer Identity.​	Sxp​Connection​Peer​Identity
OUTPUT_​SOURCE_​IP	The Source IP created on the device.​	ipaddress
OUTPUT_​PASSWORD_​OPTION	The Password Option created on the device.​	gen_​text_​input
OUTPUT_​REQUIRED_​PASSWORD	The Required Password created on the device.​	password
OUTPUT_​VRF	The VRF created on the device.​	gen_​text_​input

Create Static MACAddress

Summary

Create a static MAC address on a Nexus device.

Description

This task creates a static MAC address entry on a Nexus device. An existing VLAN ID is required.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port.​	networking_​device_​interface	Y
MAC Address	Enter MAC Address​Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE.​	gen_​text_​input	Y
VLAN ID	VLAN ID	Infra​Network​VLANIdentity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​MACADDRESS	Network device MAC Address on which selected operation performed.​	networking_​device_​mac
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create Tenant VRF

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Tenant VRF Name	Tenant VRF Name	gen_​text_​input	Y
Description	Description	gen_​text_​input
Logical Network Name	Provide Logical Network Name	hyperv_​n1k_​logical_​network_​identity
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​TENANT_​VRF	Tenant VRF	gen_​text_​input
HYPERV_​N1K_​NETWORK_​TENANT_​VRF_​IDENTITY	Tenant VRF Identity	hyperv_​n1k_​tenant_​vrf_​identity
HYPERV_​N1K_​LOGICALNETWORK	Logical Network	gen_​text_​input
HYPERV_​N1K_​LOGICALNETWORK_​IDENTITY	Logical Network Identity	hyperv_​n1k_​logical_​network_​identity

Create Uplink Network

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Uplink Name	Provide Network Uplink Name	gen_​text_​input	Y
Network Segement Pool	Provide Network Segment Pool	hyperv_​n1k_​network_​segment_​pool_​identity	Y
Port Profile	Provide Port Profile Name	infra_​network_​port_​profile_​name
Network Segment	Provide Network Segment Name	hyperv_​n1k_​network_​segment_​identity
System Network Uplink
Publish Network Uplink
Publish Network Uplink Name		gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​UPLINK	Network Uplink	gen_​text_​input
HYPERV_​N1K_​NETWORK_​UPLINK_​IDENTITY	Network Uplink Identity	hyperv_​n1k_​network_​uplink_​identity
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL	Network Segment Pool	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
HYPERV_​N1K_​NETWORK_​SEGMENT	Network Segment	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​IDENTITY	Network Segment Identity	hyperv_​n1k_​network_​segment_​identity
HYPERV_​NETWORK_​UPLINK_​IDENTITY	Hyper​V Network Uplink Identity	hyperv​Up​Link​Port​Profile​Identity

Create VFC Interface

Summary

Create a VFC on a Nexus device.

Description

This task creates a virtual fiber channel (VFC) interface on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VFC Id	VFC ID to be created.​	gen_​text_​input	Y
Select Port	Select a port .​	gen_​text_​input	Y
Switch Port Mode	Specify Switch port mode	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
VFC_​INTERFACE_​NAME	VFC Interface name	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create VLAN

Summary

Create a VLAN.

Description

This task creates a virtual LAN (VLAN) on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN ID	VLAN ID/Range	vlan​ID	Y
VLAN Name	VLAN Name	gen_​text_​input
Overwrite Existing VLAN	Select this option to overwrite any existing VLAN configuration
No Shutdown
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
VLAN_​NAME	VLAN Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​DEVICE_​VLAN_​IDENTITY	Identity for device vlan	Infra​Network​VLANIdentity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create VRF

Summary

Create a VRF.

Description

This task creates a VPN routing and forwarding (VRF).

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VRF Name	Provide VRF Context Name	gen_​text_​input	Y
Domain Name	Provide Domain Name	gen_​text_​input
DNS Servers	Provide DNS Servers	gen_​text_​input
Route	Provide Route (A.​B.​C.​D/LEN IP Prefix and Network Mask Length)	gen_​text_​input
Gateway	Provide Gateway IP	ipaddress
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​VRF	The VRF created on the device.​	gen_​text_​input
OUTPUT_​VRF_​IDENTITY	The VRF Identity created on the device.​	gen_​text_​input
OUTPUT_​CREATE_​VRF_​IDENTITY	Create VRF Identity created on the device.​	networking_​vrf_​identity
OUTPUT_​DOMAIN_​NAME	The VRF created on the device.​	gen_​text_​input

Create VSAN

Summary

Create a VSAN.

Description

This task creates a virtual storage area network (VSAN) on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VSAN ID	VSAN ID	vsan​ID	Y
VSAN Name	VSAN Name	gen_​text_​input
Enhance	Enhance the VSAN
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
VSAN_​NAME	VSAN Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Create VXLAN

Summary

Create a VXLAN on a Nexus 1000V device.

Description

This task creates a VXLAN on a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Bridge Name	Domain Name for VXLAN Bridge.​	gen_​text_​input	Y
VXLAN Id	Vx​LAN ID to be created.​	gen_​text_​input	Y
Mode Unicast	Select this option to set the Unicast mode for the VXLAN
VXLAN Group IP Address	The Multicast ip address for the Vx​LAN.​	ipaddress	Y
Distribution learning MAC	Select this option to set the flood less learning using the MAC.​
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VXLAN_​ID	VXLAN ID on which the selected operation was performed	vlan​ID
VXLAN_​DOAMIN_​NAME	VXLAN Domain Name on which the selected operation was performed	gen_​text_​input

Create VXLAN Encapsulate segment

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Bridge Name	Domain Name for VXLAN Bridge.​	gen_​text_​input	Y
encapsulation profile Segment	encapsulation profile Segment	gen_​text_​input	Y
VLAN ID	VLAN ID	Infra​Network​VLANIdentity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
ENCAPSULATION_​PROFILE_​SEGMENT_​NAME	Name of the encapsulation profile segment on which the selected operation was performed	gen_​text_​input
ENCAPSULATION_​PROFILE_​SEGMENT_​NAME_​IDENTITY	Name of the encapsulation profile segment on which the selected operation was performed	infra_​network_​encapsulation_​profile_​segment_​name

Delete ACL Entry

Summary

Delete an ACL entry.

Description

This task deletes an ACL entry.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
ACL Name	ACL Name	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​ACL_​NAME	ACL on which selected operation performed.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Associate Private VLAN

Summary

Delete an associated private VLAN.

Description

This task deletes the association of the primary VLAN to a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Primary VLAN ID	Primary VLAN	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Device Alias

Summary

Delete a device alias.

Description

This task deletes a device alias on a device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Device Alias Name	Device Alias Name	networking_​san_​device_​alias_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​SAN_​DEV_​ALIAS	Device alias on which selected operation performed.​	networking_​san_​device_​alias_​identity
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Device FCAlias

Summary

Delete a device fcAlias.

Description

This task deletes a fiber channel alias from a device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
FC Alias Name	FC Alias Name	FCAlias​Identity
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Host Name

Summary

Delete a host name on a Nexus device.

Description

This task deletes a host name on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Host Name	Select Host Name to be deleted	networking_​device_​host_​name	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
HOST_​NAME	Host Name on which the selected operation was performed	networking_​device_​host_​name
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete IP ACL Rule

Summary

Delete an IP ACL Rule from a Nexus 1000V device.

Description

This task deletes an IP access control list (ACL) rule for Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select IP ACL Rule	Select IP ACL Rule	networking_​nxos_​ip_​acl_​info	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​ACL_​NAME	ACL on which selected operation performed.​	gen_​text_​input

Delete IP Pool Template

Summary

Delete an IP pool template on a Nexus 1000V device.

Description

This task deletes an IP pool template from a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select IP Pool Template Name	Select IP Pool Template Name	Infra​Network​IPPool​Template​Identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​IP_​POOL_​TEMPLATE	IP Pool Template	gen_​text_​input
HYPERV_​N1K_​IP_​POOL_​TEMPLATE_​IDENTITY	IP Pool Template Identity	Infra​Network​IPPool​Template​Identity

Delete Inherit Port Profile

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Uplink	Provide Network Uplink	hyperv_​n1k_​network_​uplink_​identity	Y
Port Profile	Provide Port Profile		Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
HYPERV_​N1K_​NETWORK_​UPLINK	Network Uplink	gen_​text_​input
HYPERV_​N1K_​NETWORK_​UPLINK_​IDENTITY	Network Uplink Identity	hyperv_​n1k_​network_​uplink_​identity

Delete Logical Network

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Logical Network Name	Provide Logical Network Name	hyperv_​n1k_​logical_​network_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​LOGICALNETWORK	Logical Network	gen_​text_​input
HYPERV_​N1K_​LOGICALNETWORK_​IDENTITY	Logical Network Identity	hyperv_​n1k_​logical_​network_​identity

Delete MAC ACL Rule

Summary

Delete a MAC ACL Rule from a Nexus 1000V device.

Description

This task deletes a MAC access control list (ACL) rule from a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select MAC ACL Rule	Select MAC ACL Rule	networking_​nxos_​mac_​acl_​info	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​ACL_​NAME	ACL on which selected operation performed.​	gen_​text_​input

Delete N9K QOS Profile

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Platinum Class	Select this option to configure platinum class parameters
Configure Gold Class	Select this option to configure gold class parameters
Configure Silver Class	Select this option to configure silver class parameters
Configure Default Class	Select this option to configure default class parameters
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
Request Approval	Select this option to request for approval to deliver commands to device

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Delete NAT

Summary

Delete a NAT table.

Description

This task deletes a NAT table from a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select NAT	Select NAT	asa_​device_​nat_​context	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​SECURITY_​CONTEXT_​NAME	Security Context name on which selected operation performed.​	networking_​security_​context_​name
OUTPUT_​NAT_​REAL_​INTERFACE_​IDENTITY	ASA NAT REAL INTERFACE IDENTITY	Network​Named​Interface​Identity
OUTPUT_​NAT_​MAPPED_​INTERFACE_​IDENTITY	ASA NAT MAPPED INTERFACE IDENTITY	Network​Named​Interface​Identity
OUTPUT_​NAT_​SOURCE_​REAL_​OBJECT_​IDENTITY	NAT SOURCE REAL NETWORK OBJECT IDENTITY	NATSource​Or​Destination​Identity
OUTPUT_​NAT_​SOURCE_​MAPPED_​OBJECT_​IDENTITY	NAT SOURCE MAPPED NETWORK OBJECT IDENTITY	NATSource​Or​Destination​Identity

Delete NTP Configurations

Summary

Delete an NTP configuration from a Nexus device.

Description

This task deletes an NTP configurations from a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
NTP Server IP	NTP Server IP	networking_​ntp_​peer_​identity
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NTP_​SERVER_​IP	NTP server IP	ipv4Address

Delete Network Element

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Delete Network Segment

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Segment	Provide Network Segment Name	hyperv_​n1k_​network_​segment_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​SEGMENT	Network Segment	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​IDENTITY	Network Segment Identity	hyperv_​n1k_​network_​segment_​identity

Delete Network Segment Pool

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Segment Pool Name	Provide Network Segment Pool Name	hyperv_​n1k_​network_​segment_​pool_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL	Network Segment Pool	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity

Delete Port Channel

Summary

Delete a port channel.

Description

This task deletes a port channel from a device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Channel Name	Select a port channel name.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​CHANNEL_​NAME	Port channel name	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Port Profile

Summary

Delete the port profile from a Nexus device.

Description

This task deletes a port profile from a Nexus switch.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Profile	Select a port profile for deletion	infra_​network_​port_​profile_​name	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Private VLAN

Summary

Delete a private VLAN from a device.

Description

This task delete a private VLAN from a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN ID	VLAN ID/Range	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete SAN Zone

Summary

Delete a SAN zone.

Description

This task deletes a zone under a VSAN on a networking device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone	Select SAN Zone	network​SANZone​Identity	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
SAN_​ZONE_​NAME	SAN Zone Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete SAN Zone Set

Summary

Delete a SAN zone set on a Nexus device.

Description

This task deletes a SAN zone set on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone Set	Select SAN Zone	network​SANZone​Set​Identity	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
SAN_​ZONE_​NAME	SAN Zone Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​SANZONE_​SET_​IDENTITY	Identity for San Zone Set.​	network​SANZone​Set​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete Tenant VRF

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Tenant VRF Name	Tenant VRF Name	hyperv_​n1k_​tenant_​vrf_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​TENANT_​VRF	Tenant VRF	gen_​text_​input
HYPERV_​N1K_​NETWORK_​TENANT_​VRF_​IDENTITY	Tenant VRF Identity	hyperv_​n1k_​tenant_​vrf_​identity

Delete Uplink Network

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Uplink	Provide Network Uplink	hyperv_​n1k_​network_​uplink_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​UPLINK	Network Uplink	gen_​text_​input
HYPERV_​N1K_​NETWORK_​UPLINK_​IDENTITY	Network Uplink Identity	hyperv_​n1k_​network_​uplink_​identity

Delete VFC Interface

Summary

Delete a VFC interface.

Description

This task deletes a Virtual Fiber Channel (VFC) interface from a configurable fiber channel on ethernet (FCoE) Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select VFC Interface	Select VFC Interface	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VFC_​INTERFACE_​NAME	VFC Interface name	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete VLAN

Summary

Delete a VLAN.

Description

This task deletes a virtual LAN (VLAN) from a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN ID	Select VLAN ID to be deleted	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
VLAN_​NAME	VLAN Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete VRF

Summary

Delete a VRF.

Description

This task removes a VPN routing and forwarding (VRF).

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VRF Name	Provide VRF Context Name	networking_​vrf_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​VRF	The VRF created on the device.​	gen_​text_​input
OUTPUT_​VRF_​IDENTITY	The VRF Identity created on the device.​	gen_​text_​input
OUTPUT_​CREATE_​VRF_​IDENTITY	Create VRF Identity created on the device.​	networking_​vrf_​identity

Delete VSAN

Summary

Delete a VSAN.

Description

This task deletes a virtual storage area network (VSAN) on network devices.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VSAN ID	Select VSAN ID to be deleted	vsan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
VSAN_​NAME	VSAN Name on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Delete VXLAN Encapsulate segment

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
encapsulation profile Segment	encapsulation profile Segment	infra_​network_​encapsulation_​profile_​segment_​name	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
ENCAPSULATION_​PROFILE_​SEGMENT_​NAME	Name of the encapsulation profile segment on which the selected operation was performed	gen_​text_​input
ENCAPSULATION_​PROFILE_​SEGMENT_​NAME_​IDENTITY	Name of the encapsulation profile segment on which the selected operation was performed	infra_​network_​encapsulation_​profile_​segment_​name

Enable SmartZone

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VSAN ID	VSAN ID	vsan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VSAN_​ID	VSAN ID on which the selected operation was performed	vsan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Encapsulate VXLAN Port Profile with Segment

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Profile	Select the port profile	gen_​text_​input	Y
encapsulation profile Segment	encapsulation profile Segment	infra_​network_​encapsulation_​profile_​segment_​name	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
ENCAPSULATION_​PROFILE_​SEGMENT_​NAME	Name of the encapsulation profile segment on which the selected operation was performed	gen_​text_​input
ENCAPSULATION_​PROFILE_​SEGMENT_​NAME_​IDENTITY	Name of the encapsulation profile segment on which the selected operation was performed	infra_​network_​encapsulation_​profile_​segment_​name

Encapsulate VXLAN PortProfile

Summary

Encapsulate a VXLAN to a VLAN.

Description

This task encapsulates a VXLAN into a VLAN in a port profile.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Bridge Name	Domain Name for VXLAN Bridge.​	gen_​text_​input	Y
Select Port Profile	Select the port profile	gen_​text_​input	Y
VLAN ID	VLAN ID	Infra​Network​VLANIdentity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name

Execute Network Device CLI

Summary

Execute CLI commands on a network device.

Description

This task executes CLI commands on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device(s)	Select Device(s)	networking_​device	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration
CLI Commands	CLI commands to execute on the device		Y
Undo CLI Commands	Undo CLI commands to execute on the device
Error	Error string needs to check on this

Outputs

Output	Description	Type
OUTPUT_​SSH_​COMMAND	External service request ID.​	gen_​text_​input

Generic Configure SAN Zoning

Summary

Configure SAN zoning on a UCS CIMC or Nexus device.

Description

This task creates generic SAN zoning on a compute or network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Service Profile Type	Select Service Profile Type
Service Profile	Select Service Profile	ucs​Service​Profile​Identity	Y
Global Service Profile	Select UCS Central service profile to modify	UCS_​CENTRAL_​SERVICE_​PROFILE_​IDENTITY	Y
CIMC Server	Select CIMC Server	cimc​Server​Identity	Y
Configure One to One zones	Select this option to configure one to one zones.​
Activate Zone Set	Activate San Zone set after creation.​
Commit Zone	Commit the San Zone after creation.​
Device Alias	Select this option for device alias
Prefer Smart​Zoning if device supports	Select this option to enable smart zoning on the zones
Select v​HBA	Select v​HBA for Fabric A configuration	gen_​text_​input	Y
Device Alias Fab A v​HBA	Device Alias name for the v​HBA.​	gen_​text_​input
VSAN ID	VSAN ID	gen_​text_​input
Zone Name	Zone A Name	gen_​text_​input
Storage Account Type	Select Storage account type	gen_​text_​input
Storage Account Name (Primary)	Select primary Storage account for Fabric A configuration	gen_​text_​input
Storage FC Adapter (Primary)	Select primary Storage Fiber Channel Adapter for Fabric A configuration	GENERIC_​FC_​ADAPTER_​LIST	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Configure Secondary Head	Select this option to configure secondary head
Storage Account Name (Secondary)	Select secondary Storage account for Fabric A configuration	gen_​text_​input
Storage FC Adapter (Secondary)	Select secondary Storage Fiber Channel Adapter for Fabric A configuration	GENERIC_​FC_​ADAPTER_​LIST	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Secondary Zone Name	Zone A Name	gen_​text_​input
Select Device	Select device for Fabric A configuration	infra​Net​Cisco​San​Device​Identity	Y
Select Source Port	Select a source port to which server is connected.​	gen_​text_​input	Y
Select Mapping VSAN	Select a VSAN to map the VLAN.​	gen_​text_​input	Y
Configure Fabric B	Select this option to configure zones for Fabric B	Boolean
Select v​HBA	Select v​HBA for Fabric B configuration	gen_​text_​input	Y
Device Alias Fab B v​HBA	Device Alias name for the v​HBA.​	gen_​text_​input
VSAN ID	VSAN ID	gen_​text_​input
Zone Name	Zone B Name	gen_​text_​input
Storage Account Type	Select Storage account type	gen_​text_​input
Storage Account Name (Primary)	Select primary Storage account for Fabric B configuration	gen_​text_​input
Storage FC Adapter (Primary)	Select primary Storage Fiber Channel Adapter for Fabric B configuration	GENERIC_​FC_​ADAPTER_​LIST	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Configure Secondary Head	Select this option to configure secondary head
Storage Account Name (Secondary)	Select secondary Storage account for Fabric B configuration	gen_​text_​input	Y
Storage FC Adapter (Secondary)	Select secondary Storage Fiber Channel Adapter for Fabric B configuration	GENERIC_​FC_​ADAPTER_​LIST	Y
Device Alias FC Adapter	Device Alias name for the FC Adapter.​Will be used as prefix if multiple fc adapter.​	gen_​text_​input
Zone Name	Zone B Name	gen_​text_​input
Select Device	Select device for Fabric B configuration	infra​Net​Cisco​San​Device​Identity	Y
Select Source Port	Select a source port to which server is connected.​	gen_​text_​input	Y
Select Mapping VSAN	Select a VSAN to map the VLAN.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
FABRIC_​A_​ZONESET_​NAME	Name of the zoneset on which the selected operation was performed for fabric A	gen_​text_​input
OUTPUT_​FAB_​A_​ZONE_​1_​NAME	Name of the zone1 that was created for fabric A	gen_​text_​input
OUTPUT_​FAB_​A_​ZONE_​2_​NAME	Name of the zone2 that was created for fabric A	gen_​text_​input
FABRIC_​A_​DEVICE_​IP	Switch IP Address (Fabric A)	networking_​device
FABRIC_​A_​VSAN_​ID	VSAN ID on which the selected operation was performed	gen_​text_​input
OUTPUT_​FAB_​A_​ZONE_​1_​IDENTITY	Identity for SAN Zone 1 created for fabric A	gen_​text_​input
OUTPUT_​FAB_​A_​ZONE_​2_​IDENTITY	Identity for SAN Zone 2 created for fabric A	gen_​text_​input
FABRIC_​B_​ZONESET_​NAME	Name of the zoneset on which the selected operation was performed for fabric B	gen_​text_​input
OUTPUT_​FAB_​B_​ZONE_​1_​NAME	Name of the zone1 that was created for fabric B	gen_​text_​input
OUTPUT_​FAB_​B_​ZONE_​2_​NAME	Name of the zone2 that was created for fabric B	gen_​text_​input
FABRIC_​B_​DEVICE_​IP	Switch IP Address (Fabric B)	networking_​device
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
FABRIC_​B_​VSAN_​ID	VSAN ID on which the selected operation was performed	gen_​text_​input
OUTPUT_​FAB_​B_​ZONE_​1_​IDENTITY	Identity for SAN Zone 1 created for fabric B	gen_​text_​input
OUTPUT_​FAB_​B_​ZONE_​2_​IDENTITY	Identity for SAN Zone 2 created for fabric B	gen_​text_​input
OUTPUT_​FAB_​A_​PRIMARY_​PORT_​LIST_​IDENTITY	Port List Identity for SAN Zone 1 created for fabric A	gen_​text_​input
OUTPUT_​FAB_​A_​SECONDARY_​PORT_​LIST_​IDENTITY	Port List Identity for SAN Zone 2 created for fabric A	gen_​text_​input
OUTPUT_​FAB_​B_​PRIMARY_​PORT_​LIST_​IDENTITY	Port List Identity for SAN Zone 1 created for fabric B	gen_​text_​input
OUTPUT_​FAB_​B_​SECONDARY_​PORT_​LIST_​IDENTITY	Port List Identity for SAN Zone 2 created for fabric B	gen_​text_​input
FABRIC_​B_​VDC_​NAME	VDC Name (Fabric B)	nxos​VDCIdentity

Inherit Port Profile

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Uplink	Provide Network Uplink	hyperv_​n1k_​network_​uplink_​identity	Y
Port Profile	Provide Port Profile	infra_​network_​port_​profile_​name	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
HYPERV_​N1K_​NETWORK_​UPLINK	Network Uplink	gen_​text_​input
HYPERV_​N1K_​NETWORK_​UPLINK_​IDENTITY	Network Uplink Identity	hyperv_​n1k_​network_​uplink_​identity

Modify Service Policy

Summary

Modify a Service Policy.

Description

This task modifies a Service Policy on a network device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Interface	Select a port name.​	networking_​device_​interface	Y
Service Policy type	Select Specify Service Policy name for type		Y
Service Policy direction	Select Specify Service Policy name for direction
Select Policy Map	Select Policy Map	ucs​Policy​Map​Identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​SERVICE_​POLICY_​TYPE	Name of service policy on which selected operation was performed.​	gen_​text_​input
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​POLICY_​MAP	Name of policy map on which selected operation was performed.​	gen_​text_​input

Provision Network

Summary

Perform network configuration related to vmWare.

Description

This task configures the VLAN and access control list (ACL) on a device based on the network provisioning policy. When the Network Provisioning Policy is defined with a private VLAN, this task configures both primary and secondary VLANs. If an ESX(i) host is selected, this task configures the VLAN and ACL on a network device associated with the ESX(i) host and creates vSwitches on the host. If network devices are selected, the VLAN and ACL are configured on the device itself. If a Nexus 1000V switch is selected, this task configures port profiles on it.

Inputs

Input	Description	Mappable To Type	Mandatory
Use v​DC	Provision Network v​DC Hosts.​
Select Devices	Select Devices	device​Multi​Select	Y
Select v​DC	Select v​DC the network needs to associated to	v​DC	Y
Network Provisioning Policy	Network Provisioning Policy	gen_​text_​input	Y
VLAN ID	VLAN ID to use	vlan​ID
v​Switch Name	Name of the v​Switch to be created on the selected VMware hosts	v​Switch​Name

Outputs

Output	Description	Type
VLAN_​ID	VLAN ID that was created	gen_​text_​input
PORT_​GROUP	Port group that was created	gen_​text_​input
KERNEL_​PORT_​GROUP	Kernel Port group that was created	gen_​text_​input
OUTPUT_​HOST_​LIST	Comma-separated hosts on which network provision is done.​	vm​Host

Publish to SCVMM

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Object	Provide Network Object to Publish	gen_​text_​input
Network Uplink	Provide Network Uplink	hyperv_​n1k_​network_​uplink_​identity	Y
Port Profile	Provide Port Profile	infra_​network_​port_​profile_​name	Y
Network Segment	Provide Network Segment Name	hyperv_​n1k_​network_​segment_​identity	Y
Publish Name	Provide Publish Name	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
HYPERV_​N1K_​NETWORK_​SEGMENT	Network Segment	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​IDENTITY	Network Segment Identity	hyperv_​n1k_​network_​segment_​identity
HYPERV_​N1K_​NETWORK_​UPLINK	Network Uplink	gen_​text_​input
HYPERV_​N1K_​NETWORK_​UPLINK_​IDENTITY	Network Uplink Identity	hyperv_​n1k_​network_​uplink_​identity
HYPERV_​LOGICAL_​NETWORK_​IDENTITY	Hyper​V Logical Network Identity	hyperv​Logical​Network​Identity
HYPERV_​LOGICALNETWORK_​DEF_​IDENTITY	Hyper​V Network Segment Pool Identity	hyperv​Logical​Network​Def​Identity
HYPERV_​IP_​POOL_​IDENTITY	Hyper​V IP Pool Template Identity	hyperv​Ip​Pool​Identity
HYPERV_​VM_​NETWORK_​IDENTITY	Hyper​V VM Network Identity	hyperv​VMNetwork​Identity
HYPERV_​NETWORK_​UPLINK_​IDENTITY	Hyper​V Network Uplink Identity	hyperv​Up​Link​Port​Profile​Identity
HYPERV_​PORT_​PROFILE_​IDENTITY	Hyper​V Port Profile Identity	hyperv​Vna​Port​Profile​Identity

Purge Network Device Configuration Data

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Purge Type	Select Purge Type	gen_​text_​input
Date Type	Select Date Type	gen_​text_​input
Size Type	Select Size Type	gen_​text_​input
Delete Before	Delete Before	date_​time
Delete After	Delete Before	date_​time
From Date	From Date	date_​time
To Date	To Date	date_​time
Greater Size (Byte)	Provide Size in Byte	gen_​text_​input
Lesser Size (Byte)	Provide Size in Byte	gen_​text_​input
Between Size (Byte)	Provide Size in between in (Byte)	gen_​text_​input
Show Report	Select Show Report	gen_​text_​input
Purge Data Report	Select Multiple Row to Purge	gen_​text_​input

Outputs

Output	Description	Type
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Push NTP Configurations

Summary

Push an NTP configuration to a Nexus device.

Description

This task pushes a network time protocol (NTP) configuration to a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
NTP Server IP	NTP Server IP	ipv4Address
NTP Stratum number	NTP Stratum number	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NTP_​SERVER_​IP	NTP server IP	ipv4Address
OUTPUT_​NTP_​STRATUM_​NUMBER	NTP Stratum number.​	gen_​text_​input
OUTPUT_​NTP_​SERVER_​IP_​IDENTITY	NTP server IP Identity	networking_​ntp_​peer_​identity

Remove HSRP

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
HSRP Group Number	HSRP Group Number.​	HSRPGroup​Number​Identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove Member From SAN Zone

Summary

Remove a member from a SAN zone on a Nexus device.

Description

This task removes a member from a SAN zone on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone	Select SAN Zone	network​SANZone​Identity	Y
Type	Type Member	gen_​text_​input
FCALIAS	Select FCALIAS	FCAlias​Identity
Member	Value for the Member	gen_​text_​input	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​SANZONE_​MEMBER	San Zone Member Configured.​	gen_​text_​input
OUTPUT_​SANZONE_​TYPE	San Zone Type Configured.​	gen_​text_​input
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove N7K VDC

Summary

Remove a VDC from a Nexus 7000 device.

Description

This task removes a virtual device context (VDC) from a Nexus 7000 device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VDC Name	VDC Name.​	nxos​VDCIdentity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove Port From VDC

Summary

Remove a port from a VDC.

Description

This task de-allocates a port from a virtual device channel (VDC).

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VDC Name	VDC Name.​	nxos​VDCIdentity	Y
Select Port	Select a port .​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove Private VLAN Ports

Summary

Remove private VLANs from a port.

Description

This task removes the private VLANs from a port.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port to configure Private VLAN.​	gen_​text_​input	Y
Type	Private VLAN Port Type		Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove SVI

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN Interface	Select VLAN Interface	networking_​vlan_​interface_​identity	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Remove SXP Connection Peer

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Disable Device Tracking	Disable Device Tracking.​
Remove Delete Hold Period	Remove Delete Hold Timer Period.​	gen_​text_​input
Disable SXP	Disable SXP.​
Remove Default Source IP Address	Remove Default Source IP Address.​
Remove Default Password	Remove Default Password.​
Peer IP Address		Sxp​Connection​Peer​Identity	Y
Source IP Address	SXP Connection Peer Source IP Address in Format i.​i.​i.​i.​	ipaddress
Password Option	Password Option	gen_​text_​input
Required Password	Required Password.​	password
Mode	Mode	gen_​text_​input
VRF	VRF.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove San Zone From Zone Set

Summary

Remove SAN zone from zone set for the Nexus device.

Description

This task removes a SAN zone from a SAN zone set on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
SAN Zone Set	Select SAN Zone Set	network​SANZone​Set​Identity	Y
SAN Zone	Select SAN Zone	network​SANZone​Identity	Y
Commit San Zone	Select this option if the SAN Zone mode is enhanced
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​SANZONE_​SET_​IDENTITY	Identity for San Zone Set.​	network​SANZone​Set​Identity
OUTPUT_​SANZONE_​IDENTITY	Identity for San Zone.​	network​SANZone​Identity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove Static MACAddress

Summary

Remove static MAC address from a Nexus device.

Description

This task removes a static MAC address entry from a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
MAC Address	Enter MAC Address​Format: E.​E.​E or EE-EE-EE-EE-EE-EE or EE:EE:EE:EE:EE:EE or EEEE.​EEEE.​EEEE.​	networking_​device_​mac	Y
VLAN ID	VLAN ID	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​MACADDRESS	Network device MAC Address on which selected operation performed.​	networking_​device_​mac
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove System VLAN Undo Configuration

Summary

Remove VLANs from a trunk on a Nexus 1000V device.

Description

This task removes system VLANs from a trunk on a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Profile Name	Enter name for port profile	gen_​text_​input	Y
System VLANs	Select System VLANs to be removed	vlan​ID	Y
Select N1K Uplink Switch A	Select N1K Uplink Switch A Device	networking_​device	Y
Select Trunk Interface	Select trunk interface from which control vlan need to be removed.​	gen_​text_​input	Y
Control VLAN ID	Select Control VLAN ID to be removed from the trunk	vlan​ID	Y
Select N1K Uplink Switch B	Select N1K Uplink Switch B Device
Select Uplink Switch B	Select Uplink Switch B Device	networking_​device	Y
Select Trunk Interface	Select trunk interface from which control vlan need to be removed.​	gen_​text_​input	Y
Control VLAN ID	Select Control VLAN ID to be removed from the trunk	vlan​ID	Y

Outputs

No Outputs

Remove System VLAN from Port Profile

Summary

Remove system VLANs from a port profile.

Description

This task removes system VLANs from a port profile on a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Profile	Select the port profile	gen_​text_​input	Y
Select VLANs	Select System VLANs to be removed	vlan​ID	Y
Select N1K Uplink Switch A	Select N1K Uplink Switch A Device	networking_​device	Y
Select Trunk Interface	Select trunk interface from which control vlan need to be removed.​	gen_​text_​input	Y
Control VLAN ID	Select Control VLAN ID to be removed from the trunk	vlan​ID	Y
Select N1K Uplink Switch B	Select N1K Uplink Switch B Device
Select N1K Uplink Switch B	Select N1K Uplink Switch B Device	networking_​device	Y
Select Trunk Interface	Select trunk interface from which control vlan need to be removed.​	gen_​text_​input	Y
Control VLAN ID	Select Control VLAN ID to be removed from the trunk	vlan​ID	Y

Outputs

No Outputs

Remove VPC PortChannel

Summary

Remove VPC PortChannel.

Description

This task removes a virtual port channel (VPC) from a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Channel Name	Select a port channel name.​	gen_​text_​input	Y
VPC Peer​Link	Select this option Configure port channel as VPC Peer Link
Domain Id	Domain Id.​		Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Remove VXLAN

Summary

Remove a VXLAN from a Nexus 1000V device.

Description

This task removes a VXLAN from a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Bridge Name	Domain Name for VXLAN Bridge.​	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

Reset Password

Summary

Reset a password.

Description

This task resets a password on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select User Name	Select User Name	password_​reset_​username	Y

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​USERNAME	Password Reset User Name	password_​reset_​username

Switch Port Action

Summary

Configure a switch port to UP or DOWN.

Description

This task configures the administrative UP or DOWN state on a switch port.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Switch Port	Select the switch port to act on	switch​Port	Y
Switch Port Action	Switch Port Action		Y

Outputs

No Outputs

UnAssign MACAddress Port

Summary

Remove a static MAC address from the layer 3 interface on a Nexus device.

Description

This task removes the static MAC address entry from a layer 3 interface on a Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port.​	networking_​device_​interface	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NETWORKING_​DEVICE_​INTERFACE	Network device interface on which selected operation performed.​	networking_​device_​interface
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

UnAssign VXLAN PortProfile

Summary

Remove the assignment of a VXLAN from a PortProfile Nexus device.

Description

This task removes the assignment of a VXLAN from a PortProfile Nexus device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port Profile	Select the port profile	gen_​text_​input	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device

UnAssociate VSAN from VLAN

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Vlan	Vlan ID to be associated.​	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​DEVICE_​VLAN_​IDENTITY	Identity for device vlan	Infra​Network​VLANIdentity
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Unassign VLAN from Group

Summary

Unassign a VLAN from a UCS Director group.

Description

This task unassigns a VLAN from a UCS Director group.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VLAN ID	VLAN ID/Range	vlan​ID	Y
Comments	Enter comments	gen_​text_​input

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID

Update Device FCAlias

Summary

Update a device fcAlias.

Description

This task updates a fiber channel alias on a device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
FC Alias Name	FC Alias Name	FCAlias​Identity	Y
Members list	Add one or more Member detail that can be associated with Fcalias.​		Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​SAN_​FC_​ALIAS	FC alias on which selected operation performed.​	FCAlias​Identity

Update HSRP

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
HSRP Group Number	HSRP Group Number.​	HSRPGroup​Number​Identity	Y
Authentication Text	Authentication Text.​	password
Min Preempt Delay Time	Min Preempt Delay Time.​	gen_​text_​input
Priority	Priority.​	gen_​text_​input
Lower Threshhold Time	Lower Threshhold Time.​	gen_​text_​input
Upper Threshhold Time	Upper Threshhold Time.​	gen_​text_​input
Hello Interval	Hello Interval.​	gen_​text_​input
Hold Time Interval	Hold Time Interval.​	gen_​text_​input
Virtual IP Address	Virtual IP Address in Format i.​i.​i.​i.​	ipaddress
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​INTERFACE_​NAME	The Interface Name set on the device.​	gen_​text_​input
OUTPUT_​GROUP_​NUMBER	The HSRP Group Number set on the device.​	gen_​text_​input
OUTPUT_​HSRP_​GROUP_​NUMBER_​IDENTITY	The HSRP Group Number Identity.​	HSRPGroup​Number​Identity
OUTPUT_​AUTHENTICATION_​TEXT	The Authentication Text set on the device.​	password
OUTPUT_​PRIORITY	The Priority set on the device.​	gen_​text_​input
OUTPUT_​MIN_​PREEMPT_​DELAY_​TIME	The Min Preempt Delay Time set on the device.​	gen_​text_​input
OUTPUT_​LOWER_​THRESHHOLD_​PERIOD	The Lower Threshhold Period set on the device.​	gen_​text_​input
OUTPUT_​UPPER_​THRESHHOLD_​PERIOD	The Upper Threshhold Period set on the device.​	gen_​text_​input
OUTPUT_​HELLO_​INTERVAL	The Hello Interval set on the device.​	gen_​text_​input
OUTPUT_​HOLD_​INTERVAL	The Hold Interval set on the device.​	gen_​text_​input
OUTPUT_​VIRTUAL_​IP	The Virtual IP Address set on the device.​	gen_​text_​input

Update Ip Pool Template

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select IP Pool Template Name	Provide Ip Pool Template Name	Infra​Network​IPPool​Template​Identity	Y
IP Address From Range	Provide Ip Address From Range	ipaddress	Y
IP Address To Range	Provide Ip Address To Range	ipaddress	Y
Network Address	Provide Network Address	ipaddress	Y
Network Subnet Mask	Provide Network Subnet Mask	ipaddress	Y
Description	Provide Description	gen_​text_​input
Default Router	Provide Default Router	ipaddress
DNS Server	Provide DNS Server	ipaddress
DNS Suffix	Provide DNS Suffix	gen_​text_​input
Netbios Name Server	Provide Netbios Name Server	ipaddress
Select Netbios Type	Select Net​Bios Type	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​IP_​POOL_​TEMPLATE	IP Pool Template	gen_​text_​input
HYPERV_​N1K_​IP_​POOL_​TEMPLATE_​IDENTITY	IP Pool Template Identity	Infra​Network​IPPool​Template​Identity

Update N1K HyperV Port Profile

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Profile Name	Provide Port Profile Name	infra_​network_​port_​profile_​name	Y
Description	Provide Port Profile Description	gen_​text_​input
Port Profile Type	Provide Port Profile Type	networking_​device_​port_​profile_​type	Y
Channel Group Mode	Select Mode to Configure Ports and Channels	gen_​text_​input
Sub Group Type	Select Sub Group Type	gen_​text_​input
Publish Port Profile	Select to Publish VEthernet Port Profile	gen_​text_​input
Publish Port Profile Name	Select to Publish VEthernet Port Profile Name	gen_​text_​input
Mode	Select Mode Type as Trunk or Access	networking_​device_​port_​profile_​mode
Enable VXLAN Capability	Enable / Disable the VXLAN Capability.​	Boolean
Access VLAN	Select VLAN	vlan​ID	Y
Action	Select action to add or remove VLANs from port profile	gen_​text_​input
System VLAN	Select this option to add/remove the selected VLANs to System VLAN
Allowed VLANs	Select list of VLAN to be allowed in trunk mode	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
VLAN_​ID_​LIST	VLAN IDs on which the selected operation was performed	vlan​ID
HYPERV_​PORT_​PROFILE_​IDENTITY	Hyper​V Port Profile Identity	hyperv​Vna​Port​Profile​Identity

Update N7K VDC

Summary

Update the VDC for a Nexus 7000 device.

Description

This task updates a virtual device context (VDC) for a Nexus 7000 device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VDC Name	VDC Name.​	nxos​VDCIdentity	Y
Module Type	Module Type	gen_​text_​input
HA Policy	To enable High Availability Policy
Select Type	Select a HA Type .​	gen_​text_​input	Y
Select HA Policy Action	Select a HA Action .​	gen_​text_​input	Y
VDC Template Name	VDC Template Name.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Update Network Segment

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Segment	Provide Network Segment Name	hyperv_​n1k_​network_​segment_​identity	Y
Network Segment Description	Provide Network Segment Description	gen_​text_​input
Network Segment Type	Specify Ethernet/Vethernet	gen_​text_​input
IP Address / Subnet	Provide IP Address / Subnet	gen_​text_​input
IP Pool Template Name	Provide IP Pool Template Name	Infra​Network​IPPool​Template​Identity
Network Segment Pool Name	Provide Network Segment Pool Name	hyperv_​n1k_​network_​segment_​pool_​identity
Tenant VRF Name	Tenant VRF Name	hyperv_​n1k_​tenant_​vrf_​identity
System Network Segment	Select this option to enable system network segment
Type	Specify VLAN/PVLAN	gen_​text_​input	Y
Vlan	Provide Vlan ID	vlan​ID
Segement ID	Provide Segment ID	gen_​text_​input
Private VLAN Type	Specify Primary/Secondary	gen_​text_​input
Secondary VLAN Type	Specify Host/Promiscuous	gen_​text_​input
Host Type	Specify Community/Isolated	gen_​text_​input
Primary VLAN	Provide Primary VLAN	vlan​ID
Secondary VLAN	Provide Secondary VLAN	vlan​ID
Publish Network Segment		gen_​text_​input
Publish Network Segment Name		gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​SEGMENT	Network Segment	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​IDENTITY	Network Segment Identity	hyperv_​n1k_​network_​segment_​identity
HYPERV_​N1K_​IP_​POOL_​TEMPLATE	IP Pool Template	gen_​text_​input
HYPERV_​N1K_​IP_​POOL_​TEMPLATE_​IDENTITY	IP Pool Template Identity	Infra​Network​IPPool​Template​Identity
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL	Network Segment Pool	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity
VLAN_​ID	VLAN ID on which the selected operation was performed	vlan​ID
OUTPUT_​DEVICE_​VLAN_​IDENTITY	Identity for device vlan	Infra​Network​VLANIdentity
PRIMARY_​VLAN_​ID	Primary VLAN ID on which the selected operation was performed	vlan​ID
SECONDARY_​VLAN_​ID	Secondary VLAN ID on which the selected operation was performed	vlan​ID
HYPERV_​LOGICAL_​NETWORK_​IDENTITY	Hyper​V Logical Network Identity	hyperv​Logical​Network​Identity
HYPERV_​LOGICALNETWORK_​DEF_​IDENTITY	Hyper​V Network Segment Pool Identity	hyperv​Logical​Network​Def​Identity
HYPERV_​IP_​POOL_​IDENTITY	Hyper​V IP Pool Template Identity	hyperv​Ip​Pool​Identity
HYPERV_​VM_​NETWORK_​IDENTITY	Hyper​V VM Network Identity	hyperv​VMNetwork​Identity

Update Network Segment Pool

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Segment Pool Name	Provide Network Segment Pool Name	hyperv_​n1k_​network_​segment_​pool_​identity	Y
Logical Network Name	Provide Logical Network Name	hyperv_​n1k_​logical_​network_​identity
Segment Type	Specify VLAN/VXLAN/HNV Segment Types	gen_​text_​input
Multicast IP	Provide Multicast IP	ipaddress
Intra Port Communication	Select for enabling Intra Port Communication
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​LOGICALNETWORK	Logical Network	gen_​text_​input
HYPERV_​N1K_​LOGICALNETWORK_​IDENTITY	Logical Network Identity	hyperv_​n1k_​logical_​network_​identity
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL	Network Segment Pool	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity

Update Port Profile

Summary

Add or remove one or more VLANs from a port profile on a Nexus device.

Description

This task updates and enables a port profile on a Nexus switch. VLANs can be added or removed from the port profile. If the port profile is in access mode, the task can change the access VLAN. If the port profile is in trunk mode, the task can add or remove VLANs to or from the trunk.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Port Profile Name	Enter name for port profile	infra_​network_​port_​profile_​name	Y
Description	Enter description for this port profile	gen_​text_​input
Type	Select the type of port profile	networking_​device_​port_​profile_​type
Mode	Select the mode of port profile	networking_​device_​port_​profile_​mode
Enable VXLAN Capability	Enable / Disable the VXLAN Capability.​
IP address	IP address in format i.​i.​i.​i	ipaddress
IP network mask	IP network mask in format m.​m.​m.​m	ipaddress
IP next-hop address	IP next-hop address in format i.​i.​i.​i	ipaddress
Access VLAN	Select VLAN	vlan​ID	Y
Action	Select action to add or remove VLANs from port profile	gen_​text_​input
Allowed VLANs	Allowed VLANs	vlan​ID	Y
Add to System VLAN	Select this option to add the selected VLANs to System VLAN
Primary VLAN ID	Primary VLAN	vlan​ID	Y
Secondary VLAN ID	Secondary VLAN IDs to associate	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​SGT_​IDENTITY	SGT Identity.​	security​Grouptag​ID
PORT_​PROFILE_​TYPE	Name of the port profile type	networking_​device_​port_​profile_​type
PORT_​PROFILE_​MODE	Name of the port profile mode	networking_​device_​port_​profile_​mode

Update SXP Connection Peer

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Enable Device Tracking	Enable Device Tracking.​
Delete Hold Timer Period	Delete Hold Timer Period.​	gen_​text_​input
Enable SXP	Enable SXP.​
Default Source IP Address	Default SXP Connection Peer Source IP Address in Format i.​i.​i.​i.​	ipaddress
Default Password	Default Password.​	password
Source IP Address	SXP Connection Peer Source IP Address in Format i.​i.​i.​i.​	ipaddress
Password Option	Password Option	gen_​text_​input	Y
Required Password	Required Password.​	password	Y
VRF	VRF.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity
OUTPUT_​ISDEVICE_​TRACKING_​ENABLE	The Device Tracking enabled on the device.​	gen_​text_​input
OUTPUT_​DELETE_​HOLD_​PERIOD	The Delete Hold Timer set on the device.​	gen_​text_​input
OUTPUT_​ISSXP_​ENABLE	The SXP is enabled on the device.​	gen_​text_​input
OUTPUT_​DEFAULT_​SOURCE_​IP	The Default Source IP created on the device.​	ipaddress
OUTPUT_​DEFAULT_​PASSWORD	The Default Password created on the device.​	password
OUTPUT_​PEER_​IP	The Peer IP created on device.​	ipaddress
OUTPUT_​SXP_​CONNECTION_​PEER_​IDENTITY	The SXP Connection Peer Identity.​	Sxp​Connection​Peer​Identity
OUTPUT_​SOURCE_​IP	The Source IP created on the device.​	ipaddress
OUTPUT_​PASSWORD_​OPTION	The Password Option created on the device.​	gen_​text_​input
OUTPUT_​REQUIRED_​PASSWORD	The Required Password created on the device.​	password
OUTPUT_​VRF	The VRF created on the device.​	gen_​text_​input

Update Trunk

Summary

Add or remove allowed VLANs on a trunk.

Description

This task adds or removes one or more VLANs to or from the list of allowed VLANs on a trunk.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Select Port	Select a port to configure trunk.​	Infra​Network​Interface​Identity	Y
Action	Select action to add or remove VLANs from port profile	gen_​text_​input
Allowed VLANs	Allowed VLANs	vlan​ID	Y
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
ALLOWED_​VLAN_​IDS	Allowed VLAN IDsf on which the selected operation was performed	gen_​text_​input
PORT_​NAME	Name of port on which selected operation was performed.​	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​NEXUS_​VDC	The VDC created on the Nexus 7000 devices.​	nxos​VDCIdentity

Update Uplink Network

Summary

Description

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Network Uplink	Provide Network Uplink	hyperv_​n1k_​network_​uplink_​identity	Y
Network Segement Pool	Provide Network Segment Pool	hyperv_​n1k_​network_​segment_​pool_​identity
Port Profile	Provide Port Profile Name	infra_​network_​port_​profile_​name
Network Segment	Provide Network Segment Name	hyperv_​n1k_​network_​segment_​identity
System Network Uplink
Publish Network Uplink
Publish Network Uplink Name		gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
HYPERV_​N1K_​NETWORK_​UPLINK	Network Uplink	gen_​text_​input
HYPERV_​N1K_​NETWORK_​UPLINK_​IDENTITY	Network Uplink Identity	hyperv_​n1k_​network_​uplink_​identity
HYPERV_​N1K_​NETWORK_​SEGMENT_​POOL_​IDENTITY	Network Segment Pool Identity	hyperv_​n1k_​network_​segment_​pool_​identity
PORT_​PROFILE_​NAME	Name of the port profile on which the selected operation was performed	infra_​network_​port_​profile_​name
HYPERV_​N1K_​NETWORK_​SEGMENT	Network Segment	gen_​text_​input
HYPERV_​N1K_​NETWORK_​SEGMENT_​IDENTITY	Network Segment Identity	hyperv_​n1k_​network_​segment_​identity
HYPERV_​NETWORK_​UPLINK_​IDENTITY	Hyper​V Network Uplink Identity	hyperv​Up​Link​Port​Profile​Identity

Update VRF

Summary

Update a VRF.

Description

This task updates a VPN routing and forwarding (VRF).

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
VRF Name	Provide VRF Context Name	networking_​vrf_​identity	Y
Add/Delete Route​IP and Gateway	Select this option to Add/Delete Route​IP and Gateway
Route	Provide Route (A.​B.​C.​D/LEN IP Prefix and Network Mask Length)	gen_​text_​input
Gateway	Provide Gateway IP	ipaddress
Route & Gateway	Select Route & Gateway to delete	gen_​text_​input
Domain Name	Provide Domain Name	gen_​text_​input
DNS Servers	More than 1 DNS Servers are allowed separated by ','(Comma) or ' '(Space).​ Maximum 6 DNS Servers are allowed for one VRF.​	gen_​text_​input
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
OUTPUT_​VRF	The VRF created on the device.​	gen_​text_​input
OUTPUT_​VRF_​IDENTITY	The VRF Identity created on the device.​	gen_​text_​input
OUTPUT_​DOMAIN_​NAME	The VRF created on the device.​	gen_​text_​input

Update VXLAN

Summary

Update a VXLAN for a Nexus 1000V.

Description

This task updates a VXLAN for a Nexus 1000V device.

Inputs

Input	Description	Mappable To Type	Mandatory
Select Device	Select Device	networking_​device	Y
Bridge Name	Domain Name for VXLAN Bridge.​	gen_​text_​input	Y
VXLAN Id	Vx​LAN ID to be updated.​	gen_​text_​input	Y
Mode Unicast	Select this option to set the Unicast mode for the VXLAN
VXLAN Group IP Address	The Multicast ip address for the Vx​LAN.​	ipaddress	Y
Distribution learning MAC	Select this option to set the flood less learning using the MAC.​
Copy Running configuration to Startup configuration	Select this option to copy running configuration to startup configuration

Outputs

Output	Description	Type
DATACENTER	Name of the Datacenter on which the selected operation was performed	datacenter​Name
DEVICE_​IP	IP address of the device on which the selected operation was performed	gen_​text_​input
OUTPUT_​NETWORKING_​DEVICE	Network device on which selected operation performed.​	networking_​device
VXLAN_​ID	VXLAN ID on which the selected operation was performed	vlan​ID
VXLAN_​DOAMIN_​NAME	VXLAN Domain Name on which the selected operation was performed	gen_​text_​input