NetApp ONTAP Tasks

This chapter contains the following sections:

Abort NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
System Path The system path of the snapvault.​ Net​App​Snap​Vault​Identity Y
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity

Add Disk to NetApp 7-Mode Aggregate

Summary
Assign disk(s) to the aggregate.
Description
The available spare disk(s) can be assigned to an aggregrate.
Inputs
Input Description Mappable To Type Mandatory
Aggregate Name Select an aggregate in which disk(s) to be added.​ aggregate​Identity Y
Disk Name Select disk(s) to add to aggregate.​ gen_​text_​input Y
Outputs
Output Description Type
OUTPUT_​AGGREGATE_​NAME Name of the Aggregate.​ netapp​Aggregate​Name
OUTPUT_​AGGREGATE_​IDENTITY Identity of the Aggregate aggregate​Identity

Add Existing Initiator to NetApp 7-Mode iGroup

Summary
Add an existing initiator of an host node to the existing Initiator Group.
Description
This task will add the initiator to the initiator group of same type(iSCSI/FCP). Task will list out all the existing iSCSI and FCP initiators followed by the type iSCSI/FCP for the selected host node. So that we can select the appropriate initiator based on the selected initiator group of type iSCSI/FCP. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer.​ filer​Identity Y
Hostnode Select a Hostnode.​ vm​Host Y
Initiator Group Type Select type of the initiator group.​ gen_​text_​input
Initiator Name Select the Initiator that needs to be deleted.​ gen_​text_​input Y
Initiator Group Name Select the Initiator Group.​ net​App​Initiator​Group​Name Y
Outputs
Output Description Type
INITIATOR_​GROUP_​NAME Name of the Initiator Group on which the selected operation was performed net​App​Initiator​Group​Name
INITIATOR_​NAME Name of the Initiator on which the selected operation was performed initiator​Name
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​HOST_​NAME Host Name vm​Host

Add IP Address to NetApp 7-Mode vFiler

Summary
Add multiple IP Addresses to a vFiler.
Description
This task will add more than one IP Addresses to a selected vfiler. So that vFiler IP addresses can be configured to different network traffic. We can give comma separated IP Address as input. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name v​Filer​Identity Y
IP Address Enter new IP Address for the selected v​Filer.​ gen_​text_​input Y
Outputs
Output Description Type
VFILER_​NAME Name of the v​Filer gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
VFILER_​IP_​ADDRESS IP Address of the v​Filer on which the selected operation was performed gen_​text_​input

Add License to NetApp 7-Mode Controller

Summary
Apply license to the Filer
Description
When a new Filer is discovered the license needs to be added.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Filer Identity Name gen_​text_​input Y
License Code Enter the License Code.​ gen_​text_​input Y
Outputs
No Outputs

Add NetApp 7-Mode NFS Export

Summary
Mount NFS storage.
Description
This task enables pathnames for mounting according to the rules specified. New rules for the pathnames take effect immediately, ignoring previous rules for specified pathnames. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Export Path Enter the path that will be exported to NFS clients.​ gen_​text_​input
Actual Path Enter the actual path mounted when the NFS client mounts the exported path.​ volume​Identity Y
Read-Write Hosts Enter comma-separated list of hosts that should have read-write access.​ gen_​text_​input Y
Root Hosts Enter comma-separated list of hosts that should have root access.​ gen_​text_​input Y
All Hosts Permissions to all hosts? Y
Persist NFS Export Rule Check this option to persist NFS Export rule.​ Y
nosuid nosuid Y
Outputs
Output Description Type
NFS_​EXPORT_​PATH NFS Export Path gen_​text_​input
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT NFS_​EXPORT_​IDENTITY Identity of the Nfs Export Netappnfs​Export​Identity
OUTPUT_​NETAPP_​ACCOUNT_​IDENTITY Identity of Netapp Account Identity net​App​Account​Identity

Add NetApp 7-Mode Qtree NFS Export

Summary
Create a NFS export rule for the QTree in the storage system using ONTAP.
Description
This task will create a NFS export rule with the access permissions for the QTree i.e., QTree to accesses the host servers. If we choose peristent option in the task, the export rule will be persisted in the file /etc/exportfs which is stored in the storage system, otherwise the rule will be stored in the teporary RAM memory of the storage system. The main advantage for choosing persistent option is the export rule will not delete from the storage system even the system restarts. The non persistent export rule will erase from the temporary memory when the system restarts. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Export Path Enter the path that will be exported to NFS clients.​ gen_​text_​input Y
Actual Path Enter the actual path mounted when the NFS client mounts the exported path.​ v​Filer​Qtree​Identity Y
Read-Write Hosts Enter comma-separated list of hosts that should have read-write access.​ gen_​text_​input Y
Root Hosts Enter comma-separated list of hosts that should have root access.​ gen_​text_​input Y
Security Select the security flavors that apply for this export.​ gen_​text_​input Y
Persist NFS Export Rule Check this option to persist NFS Export rule.​ Y
nosuid nosuid Y
Outputs
Output Description Type
NFS_​EXPORT_​PATH NFS Export Path gen_​text_​input
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input

Add NetApp CIFS Volume Share

Summary
Configure and display CIFS shared volume information.
Description
This task will configure a volume as shared resource and make this shared volume visible to the user who is authenticated to access. This task will work only for ONTAP accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the Volume in which CIFS share to be created v​Filer​CIFSVolume​Identity Y
Share Name Enter Share Path gen_​text_​input Y
Description Enter share description
Outputs
Output Description Type
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
OUTPUT_​VFILER_​VOLUME_​IDENTITY Identity of the v​Filer Volume v​Filer​Volume​Identity
OUTPUT_​VFILER_​CIFS_​VOLUME_​IDENTITY Identity of the v​Filer CIFS Volume v​Filer​CIFSVolume​Identity
OUTPUT_​CIFS_​SHARE_​NAME Name of the CIFS Share.​ cifs​Share​Name

Add NetApp Initiator to Initiator Group

Summary
Add an Initiator to an Initiator group.
Description
An Initiator provides the link between a host node and a LUN. This initiator is managed by the Initiator group. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Select the Initiator Group in which new Initiator needs to be added.​ i​Group​Identity Y
Initiator Name Enter the name of the Initiator that needs to be created.​ gen_​text_​input Y
Force Forcibly Add
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
INITIATOR_​GROUP_​NAME Name of the Initiator Group on which the selected operation was performed net​App​Initiator​Group​Name
INITIATOR_​NAME Name of the Initiator on which the selected operation was performed initiator​Name
OUTPUT_​IGROUP_​IDENTITY Identity of the i​Group i​Group​Identity
OUTPUT_​ALL_​VFILER_​IDENTITY Identity of the All v​Filers net​App​All​VFilers​Identity

Add NetApp vFiler Initiator to Initiator Group

Summary
Add an Initiator to an vFiler Initiator group.
Description
An Initiator provides the link between a host node and a LUN. This initiator is managed by the Initiator group. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Select the Initiator Group in which new Initiator needs to be added.​ v​Filer​IGroup​Identity Y
Initiator Name Enter the name of the Initiator that needs to be created.​ gen_​text_​input Y
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VFILER_​INITIATOR_​GROUP_​NAME Name of the vfiler Initiator Group on which the selected operation was performed vfiler​Initiator​Group​Name
VFILER_​INITIATOR_​_​NAME Name of the vfiler Initiator on which the selected operation was performed vfiler​Initiator
OUTPUT_​VFILER_​IGROUP_​IDENTITY Identity of the v​Filer Initiator Group v​Filer​IGroup​Identity
OUTPUT_​ALL_​VFILER_​IDENTITY Identity of the All v​Filers net​App​All​VFilers​Identity

Add NetApp vFiler NFS Volume Export

Summary
Create a NFS export rule for the volume in the storage system.
Description
This task will create a NFS export rule with the access permissions for the vfiler storage path i.e., volume to accesses the host servers. If we choose peristent option in the task, the export rule will be persisted in the file /etc/exportfs which is stored in the storage system, otherwise the rule will be stored in the teporary RAM memory of the storage system. The main advantage for choosing persistent option is the export rule will not delete from the storage system even the system restarts. The non persistent export rule will erase from the temporary memory when the system restarts. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Export Path Enter the path that will be exported to NFS clients.​ gen_​text_​input
Actual Path Enter the actual path mounted when the NFS client mounts the exported path.​ v​Filer​Volume​Identity Y
Read-Write Hosts Enter comma-separated list of hosts that should have read-write access.​ gen_​text_​input Y
Root Hosts Enter comma-separated list of hosts that should have root access.​ gen_​text_​input Y
Security Select the security flavors that apply for this export.​ gen_​text_​input Y
Persist NFS Export Rule Check this option to persist NFS Export rule.​ Y
nosuid nosuid Y
Outputs
Output Description Type
NFS_​EXPORT_​PATH NFS Export Path gen_​text_​input
VFILER_​NAME v​Filer Name gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity

Add Quota to NetApp 7-Mode Volume

Summary
Creates a Quota for the Qtree under the volume.
Description
This task will creates a quota rule for the QTree under the volume. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select a Volume Allv​Filer​Volume​Identity Y
Qtree Name Select Qtree Name net​App​QTree​Name Y
Quota Type Select Quota Type gen_​text_​input Y
Disk Space Hard Limit (GB) Enter disk space hard limit in GB gen_​text_​input
Files Hard Limit Enter files hard limit gen_​text_​input
Threshold (GB) Enter threshold value in GB gen_​text_​input
Disk Space Soft Limit (GB) Enter disk space soft limit in GB gen_​text_​input
Files Soft Limit Enter files soft limit gen_​text_​input
Outputs
Output Description Type
OUTPUT_​ALL_​VFILER_​VOLUME_​IDENTITY Identity of the All v​Filers volume Allv​Filer​Volume​Identity

Add Storage to NetApp vFiler

Summary
Add Storage components to vFiler
Description
Adding storage to vFiler involves creating Volumes, LUNs, Qtrees or any other storage units and adding them to the vFiler. Security style NTFS option can be choosed to create a volume having the security style as NTFS otherwise volume will be created with style as UNIX. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Identity Select a v​Filer to add storage.​ gen_​text_​input Y
Aggregate Name Select an aggregate in which Volume needs to be created.​ aggregate​Identity Y
Storage Name Enter the Name of the Storage to be created.​ gen_​text_​input
Storage Size Enter the size of Storage.​ net​App​Vol​Size Y
Volume Size Units Select the Volume Size Units.​ size​Unit Y
Space Guarantee Select the Space Guarantee.​ space​Guarantee Y
Snapshot Size (%) Enter the percentage of the volume snapshot.​ net​App​Volume​Snapshot​Percent
Security Style NTFS Do you want to set security style as NTFS?
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VFILER_​NAME Name of the v​Filer on which the selected operation was performed gen_​text_​input
VFILER_​IP_​ADDRESS IP Address of the v​Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
VOLUME_​NAME Name of the Volume on which the selected operation was performed volume
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​VFILER_​VOLUME_​IDENTITY Identity of the v​Filer Volume v​Filer​Volume​Identity
OUTPUT_​VFILER_​CIFS_​VOLUME_​IDENTITY Identity of the v​Filer CIFS Volume v​Filer​CIFSVolume​Identity
OUTPUT_​ALL_​VFILER_​VOLUME_​IDENTITY Identity of the All v​Filers volume Allv​Filer​Volume​Identity
OUTPUT_​ONTAP_​ALL_​VFILER_​IDENTITY Identity of the All ONTAP vfilers including vfiler0 net​App​ONTAPAll​VFilers​Identity

Assign VLAN to NetApp IP Space

Summary
Assigns selected interface to IP Space.
Description
This task will assign the selected VLAN interface to the IP Space. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
IP Space Name Select the IP Space that need to be assigned to the VLAN Interface.​ ip​Space​Identity Y
Interface Name Select the VLAN interface to which the IP Space need to be assigned.​ un​Assigned​Interface​Identity Y
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
IPSPACE_​NAME Name of the IP Space on which the selected operation was performed ip​Space​Name
OUTPUT_​IPSPACE_​IDENTITY Identity of the IP Space ip​Space​Identity
VLAN_​INTERFACE_​NAME Name of the v​Lan Interface on which the selected operation was performed v​LANinterface​Name
OUTPUT_​VLAN_​ID VLAN ID vlan​ID
OUTPUT_​INTERFACE_​IDENTITY Identity of the interface un​Assigned​Interface​Identity

Associate NetApp 7-Mode Volume as VMware NFS Datastore

Summary
Associate a volume as NFS Datastore.
Description
This task associates an existing volume as NFS datastore. In this task we can select the NFS Enabled IP Address which is NFS protocol enabled IP Address for NFS traffic only.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Filer Identity Name filer​Identity Y
NFS Enable IP Address Select a IP Address.​ ipaddress Y
Hostnode Select a hostnode.​ vmware​Host​Multi​Select Y
NFS Path Enter the NFS Path.​ gen_​text_​input Y
Datastore Name Enter the datastore name.​ gen_​text_​input
Access Mode Select an access mode.​ gen_​text_​input Y
Success Criteria Success Criteria gen_​text_​input Y
Outputs
Output Description Type
OUTPUT_​VMWARE_​ACCOUNT_​NAME VMware account name.​ gen_​text_​input
OUTPUT_​VMWARE_​DATASTORE_​NAME Datastore name data​Store​Name
OUTPUT_​VMWARE_​DATASTORE_​IDENTITY Datastore name identity vmware​Datastore​Identity
OUTPUT_​VMWARE_​DATASTORE_​INFO_​IDENTITY Datastore Info identity gen_​text_​input
OUTPUT_​VMWARE_​HOST_​NODE_​IDENTITY VMware Host Node Identity vmware​Host​Node​Identity
OUTPUT_​VMWARE_​HOST_​NODE_​NAME Host Node Name.​ vmware​Host​Multi​Select

Associate NetApp vFiler Volume as NFS Datastore

Summary
Associate a vFiler volume as NFS Datastore.
Description
This task associates an existing vFiler volume as NFS datastore. In this task we can select the NFS Enabled IP Address which is NFS protocol enabled IP Address for NFS traffic only.\ This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name v​Filer​Identity Y
NFS Enable IP Address Select a IP Address.​ ipaddress Y
Hostnode Select a hostnode.​ vmware​Host​Multi​Select Y
NFS Path Enter the NFS Path.​ gen_​text_​input Y
Datastore Name Enter the datastore name.​ gen_​text_​input
Access Mode Select an access mode.​ gen_​text_​input Y
Success Criteria Success Criteria gen_​text_​input Y
Outputs
Output Description Type
OUTPUT_​VMWARE_​ACCOUNT_​NAME VMware account name.​ gen_​text_​input
OUTPUT_​VMWARE_​DATASTORE_​NAME Datastore name data​Store​Name
OUTPUT_​VMWARE_​DATASTORE_​IDENTITY Datastore name identity vmware​Datastore​Identity
OUTPUT_​VMWARE_​DATASTORE_​INFO_​IDENTITY Datastore Info identity gen_​text_​input
OUTPUT_​VMWARE_​HOST_​NODE_​IDENTITY VMware Host Node Identity vmware​Host​Node​Identity
OUTPUT_​VMWARE_​HOST_​NODE_​NAME Host Node Name.​ vmware​Host​Multi​Select

Clone NetApp LUN

Summary
Clones selected LUN.
Description
Starts a LUN clone operation asynchronously. If the clone operation starts successfully, a unique clone-id is returned. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select LUN to be renamed lun​Identity Y
New LUN Name Enter the new LUN Name.​ gen_​text_​input Y
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
LUN_​IDENTITY Identity of the LUN lun​Identity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity

Configure NetApp SnapMirror

Summary
Sets up a connection.
Description
This task will sets up a new connection or modify existing connection.
Inputs
Input Description Mappable To Type Mandatory
Filer/v​Filer Name Select Filer Name or v​Filer Name net​App​All​VFilers​Identity Y
Connection Name Name of the connection to add or modify.​ gen_​text_​input Y
Mode Type of the mode gen_​text_​input
Address Pair 1 Connection's first source and destination address pair.​ In multi mode, first address pair provides a connection path; while in failover mode, first address pair provides the prefer connection path.​
Source Address Source address in the form of filer name or IP.​ gen_​text_​input Y
Destination Address Destination address in the form of filer name or IP.​ gen_​text_​input Y
Address Pair 2 Connection's second source and destination address pair.​ In multi mode, second address pair provides another connection path; while in failover mode, second address pair provides the connection path in case first path fails.​.​
Source Address Source address in the form of filer name or IP.​ gen_​text_​input
Destination Address Destination address in the form of filer name or IP.​ gen_​text_​input
Remote Access
Snapmirror Access IPs Enter destination filer/vfiler IP Addesses to access the selected source filer/vfiler.​ gen_​text_​input Y
Outputs
No Outputs

Configure NetApp VLAN Interface

Summary
Configure network interfaces of filer.
Description
This task will configures network interface and persist in the /etc/rc file.
Inputs
Input Description Mappable To Type Mandatory
IP Space Name Select the IP Space that need to be assigned to the VLAN Interface.​ ip​Space​Identity Y
Interface Name Select the VLAN interface to which the IP Space need to be assigned.​ un​Assigned​Interface​Identity Y
MTU Size Enter MTU size gen_​text_​input
Configure Partner Select partner v​LAN interface
Partner Interface Name Select Partner v​LAN Interface un​Assigned​Interface​Identity Y
Partner IPSpace Name Select the IP Space that need to be assigned to the VLAN Interface.​ ip​Space​Identity Y
IP Address Enter IP Address for the partner v​LAN interface gen_​text_​input
Subnet mask Enter netmask for the partner v​LAN interface gen_​text_​input
Creator Entity responsible for creation of address(vfiler/SVM).​ gen_​text_​input
Make Configuration Persistent Do you want to persist the configuration?
Negotiated Failover Do you want to enable negotiated failover?
Outputs
No Outputs

Create NetApp Aggregate

Summary
Creation of the aggregate.
Description
This task will create an aggregrate.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Filer Identity Name filer​Identity Y
Aggregate Name Enter Aggregate Name.​ netapp​Aggregate​Name Y
Disk Count Enter Number of disks.​ gen_​text_​input
Disk List Select disks to be aggregated.​ netapp​Spare​Disk​List
Raid Type Choose raid type.​ netapp​Raid​Type
Outputs
Output Description Type
OUTPUT_​AGGREGATE_​NAME Name of the Aggregate.​ netapp​Aggregate​Name
OUTPUT_​AGGREGATE_​IDENTITY Identity of the Aggregate aggregate​Identity
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity

Create NetApp Flexible Volume

Summary
Create a flexible volume.
Description
A traditional volume can be resized to a bigger size but cannot be reduced in size. A flexible volume on the other hand can be resized to either a bigger or smaller size. A traditional volume is tightly coupled with its containing aggregate. In order to increase the size of the traditional volume additional disk can be added. A flexible volume is loosely coupled with its containing aggregate and hence size can be increased or decreased. Security style NTFS option can be choosed to create a volume having the security style as NTFS otherwise volume will be created with style as UNIX. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Aggregate Name Select an aggregate in which Volume needs to be created.​ aggregate​Identity Y
Volume Name Enter the Name of the Volume to be created.​ gen_​text_​input
Volume Size Enter the size of Volume.​ net​App​Vol​Size Y
Volume Size Units Select the Volume Size Units.​ size​Unit Y
Space Guarantee Select the Space Guarantee.​ space​Guarantee Y
Snapshot Size (%) Enter the percentage of the volume snapshot.​ net​App​Volume​Snapshot​Percent
Security Style NTFS Do you want to set security style as NTFS?
NFS Export Do you want to create NFS export path automatically?
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​ONCOMMAND_​FILER_​IDENTITY Identity of the On​Command Filer dfm​Filer​Identity
VOLUME_​NAME Name of the Volume on which the selected operation was performed volume
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​AGGREGATE_​IDENTITY Identity of the Aggregate aggregate​Identity
OUTPUT_​VFILER_​CIFS_​VOLUME_​IDENTITY Identity of the v​Filer CIFS Volume v​Filer​CIFSVolume​Identity
OUTPUT_​ALL_​VFILER_​VOLUME_​IDENTITY Identity of the All v​Filers volume Allv​Filer​Volume​Identity
OUTPUT_​NETAPP_​ACCOUNT_​IDENTITY Identity of Netapp Account Identity net​App​Account​Identity
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
NFS_​EXPORT_​PATH NFS Export Path gen_​text_​input

Create NetApp IP Space

Summary
Create a new IP Space.
Description
Creates a new IP Space with the given name in specified filer. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer in which the new IP Space need to be created.​ filer​Identity Y
IP Space Name Enter the Name of the IP Space to be created.​ ip​Space​Name
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
IPSPACE_​NAME Name of the IP Space on which the selected operation was performed ip​Space​Name
OUTPUT_​IPSPACE_​IDENTITY Identity of the IP Space ip​Space​Identity
OUTPUT_​UNASSIGNED_​IPSPACE_​IDENTITY Identity of the Un​Assigned IP Space un​Assignedip​Space​Identity

Create NetApp Initiator Group

Summary
Create a Initiator Group
Description
Initiator group is a list of initiators (iSCSI or fabric adapters). Create an Initiator group which can used to group initiators in a separate task. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer in which new Initiator Group need to be created.​ filer​Identity Y
Initiator Group Name Enter a group name for the initiator group.​ gen_​text_​input
Group Type Select a Type for the initiator group.​ net​App​Initiator​Group​Type Y
OS Type Select the operating system type of the initiators in this group.​ ostype Y
Port Set Port Set net​App​Bind​Port​Set
Outputs
Output Description Type
INITIATOR_​GROUP_​NAME Name of the Initiator Group on which the selected operation was performed net​App​Initiator​Group​Name
OUTPUT_​IGROUP_​IDENTITY Identity of the i​Group i​Group​Identity
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​ALL_​VFILER_​IDENTITY Identity of the All v​Filers net​App​All​VFilers​Identity

Create NetApp LUN

Summary
Create a LUN
Description
A LUN is a Storage Unit (Logical Unit Number). This task is for creating the LUN storage unit. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select a Volume in which new LUN needs to be created.​ volume​Identity Y
LUN Name Enter the Name of the LUN that is to be created.​ lun​Name
OS Type Select the operating system type.​ ostype Y
LUN Size The size of the LUN.​ net​App​Lun​Size Y
LUN Size Units Select the LUN Size Units.​ size​Unit Y
Reserve Space Reserve Space
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
LUN_​IDENTITY Identity of the LUN lun​Identity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​NETAPP_​ACCOUNT_​IDENTITY Identity of Netapp Account Identity net​App​Account​Identity

Create NetApp QTree

Summary
Creates a new QTree under the selected volume.
Description
This task will create new QTree under the selected volume. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select a Volume Allv​Filer​Volume​Identity Y
Qtree Name Enter qtree name net​App​QTree​Name
Outputs
Output Description Type
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
OUTPUT_​VFILER_​VOLUME_​IDENTITY Identity of the v​Filer Volume v​Filer​Volume​Identity
OUTPUT_​VFILER_​QTREE_​IDENTITY Identity of the v​Filer Qtree v​Filer​Qtree​Identity
OUTPUT_​ALL_​VFILER_​VOLUME_​IDENTITY Identity of the All v​Filers volume Allv​Filer​Volume​Identity
OUTPUT_​QTREE_​IDENTITY Identity of the Qtree net​App​QTree​Identity
OUTPUT_​QTREE_​NAME Name of the QTree.​ net​App​QTree​Name

Create NetApp SnapMirror Schedule

Summary
Creates Snapmirror Schedule
Description
This task will be used to schedule snap mirrors
Inputs
Input Description Mappable To Type Mandatory
Source Location Source location of a schedule to set.​ Allv​Filer​Volume​Identity Y
Select Option Option to choose existing volume or create a new volume as destination in the current filer or vfiler.​
Destination Location Destination location of a schedule to set.​ gen_​text_​input Y
v​Filer Name Select a v​Filer to add storage.​ gen_​text_​input Y
Aggregate Select aggregate to create a flexible volume.​ gen_​text_​input Y
Volume Name Enter new destination volume name.​ gen_​text_​input
Volume Size (GB) Enter new destination volume size.​ gen_​text_​input Y
Space Guarantee Select the Space Guarantee.​ gen_​text_​input Y
Minutes Minutes in the hour for which the schedule is set.​Possible values:(-)=match nothing, (1)=match minute 1, (1,3)=match minute 1 and 3, (*)=match all possible legal values.​ gen_​text_​input Y
Hours Hours in the day for which the schedule is set.​Possible values:(-)=match nothing, (1)=match hour 1, (1,3)=match hour 1 and 3, (*)=match all possible legal values.​ gen_​text_​input Y
Days of Month Minutes in the hour for which the schedule is set.​Possible values: (-)=match nothing, (1)=match day 1, (1,3)=match day 1 and 3, (2-5)=match day 2,3,4,5 , (*)=match all possible legal values.​ gen_​text_​input Y
Days of Week Days in the week for which the schedule is set.​ 0 represents sunday, and 6 represents saturday.​Possible values:(-)=match nothing, (1)=match day 1(Monday), (1,3)=match day 1(Monday) and 3(Wednesday), (2-5)=match day 2,3,4,5(Tuesady to Friday) , (*)=match all possible legal values.​ gen_​text_​input Y
Max Transfer Rate (KB) Maximun transfer rate kilobytes per second.​ Default is as fast as filer can transfer.​ gen_​text_​input
Outputs
Output Description Type
OUTPUT_​ALL_​VFILER_​SNAPMIRROR_​DESTINATION_​IDENTITY Identity of the all vfiler and vfiler0 snapmirror destination identity.​ net​App​Allv​Filers​Snapmirror​Destination​Identity

Create NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
Primary System Primary system filer​Identity Y
Source Path Source Path.​ net​App​QTree​Identity Y
Destination Volume Destination volume.​ volume​Identity Y
New Destination QTree Name New Destination qtree name.​ gen_​text_​input Y
Maximum Transfer Rate Maximim transfer rate in KBs.​ gen_​text_​input
Tries Count Maximum value is 120.​ gen_​text_​input
Connection Mode Connection mode.​ gen_​text_​input
Allow Open File Backup Select checkbox to allow open file backup Boolean
Ignore Access time Change Select checkbox to ignore access time change Boolean
Use Compression Select action to specify whether to use compression or not.​ gen_​text_​input
Primary Path UTF8 Encoded Select checkbox to enable primary path utf8 encoding.​ Boolean
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity

Create NetApp Volume Snapshot

Summary
Create a Volume Snapshot.
Description
A volume can be backed up using the snapshot feature. Snapshot can be used for the purpose of backup and recovery of a Volume. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the volume for which snapshot to be created.​ volume​Identity Y
Snapshot Name Enter the name of the snapshot to be created.​ net​App​Vol​Snapshot Y
Is Valid Lun Clone Snapshot Is Valid Lun Clone Snapshot gen_​text_​input
Async Async gen_​text_​input
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VOLUME_​NAME Name of the Volume on which the selected operation was performed volume
SNAPSHOT_​NAME Name of the Snapshot on which the selected operation was performed net​App​Vol​Snapshot
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity

Create NetApp vFiler Initiator Group

Summary
Create an vFiler Initiator Group
Description
Initiator group is a list of initiators (iSCSI or fabric adapters). Create an Initiator group which can used to group initiators in a separate task. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select the v​Filer in which new Initiator Group need to be created.​ v​Filer​Identity Y
Initiator Group Name Enter a group name for the initiator group.​ vfiler​Initiator​Group​Name
Group Type Select a Type for the initiator group.​ net​App​Initiator​Group​Type Y
OS Type Select the operating system type of the initiators in this group.​ ostype Y
Port Set Port Set net​App​Bind​Port​Set
Outputs
Output Description Type
VFILER_​INITIATOR_​GROUP Name of the vfiler Initiator Group on which the selected operation was performed vfiler​Initiator​Group
OUTPUT_​VFILER_​IGROUP_​IDENTITY Identity of the v​Filer Initiator Group v​Filer​IGroup​Identity
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
OUTPUT_​ALL_​VFILER_​IDENTITY Identity of the All v​Filers net​App​All​VFilers​Identity

Create NetApp vFiler LUN

Summary
Creates a vFiler LUN.
Description
This task creates a vFiler LUN.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select a Volume in which new LUN needs to be created.​ v​Filer​Volume​Identity Y
LUN Name Enter the Name of the LUN that is to be created.​ lun​Name
OS Type Select the operating system type.​ ostype Y
LUN Size The size of the LUN.​ net​App​Lun​Size Y
LUN Size Units Select the LUN Size Units.​ size​Unit Y
Reserve Space Reserve Space
Outputs
Output Description Type
VFILER_​LUN_​PATH Path of the vfiler LUN on which the selected operation was performed net​App​Lun​Path
OUTPUT_​VFILER_​LUN_​IDENTITY Identity of the v​Filer LUN v​Filer​LUNIdentity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity

Create NetApp vFiler Setup

Summary
Sets up services for selected vFiler.
Description
Set up services for a vFiler that has already been created. At least one of the optional arguments must be specified. If vfiler IP address is desired to map from previous task (Add IP Address to vFiler), then user should check the Alternate vFiler IP checkbox option in this task. Enter the DNS domain name for the vfiler and the IP addresses of the vfiler's domain servers which are helpful to CIFS setup. This task will work only for ONTAP account.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name v​Filer​Identity Y
Alternate v​Filer IP Select alternate v​Filer IP Address for setup
IP Address Enter IP Address for the selected v​Filer gen_​text_​input
Subnet mask Enter Subnet mask gen_​text_​input Y
DNS Domain Enter DNS Domain gen_​text_​input
DNS Server Addresses Enter list of DNS Server IP Addresses gen_​text_​input
Interface Name Interface Name gen_​text_​input
Default Gateway Enter default gateway gen_​text_​input
Protocols Select the Protocols.​ vfiler​Protocol
Outputs
Output Description Type
VFILER_​NAME Name of the v​Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
OUTPUT_​ONTAP_​ALL_​VFILER_​IDENTITY Identity of the All ONTAP vfilers including vfiler0 net​App​ONTAPAll​VFilers​Identity

Create NetApp vLAN Interface

Summary
Creates a new vLAN.
Description
Creates a new vLAN interface using the specified physical and virtual interface names and VLAN ID. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Interface Name Enter the Physical Interface Name.​ v​LANPhys​Inf​Identity Y
VLAN ID Enter the VLAN ID.​ vlan​ID Y
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VLAN_​INTERFACE_​NAME Name of the v​Lan Interface on which the selected operation was performed v​LANinterface​Name
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​ONCOMMAND_​FILER_​IDENTITY Identity of the On​Command Filer dfm​Filer​Identity
OUTPUT_​VLAN_​ID VLAN ID vlan​ID
OUTPUT_​INTERFACE_​IDENTITY Identity of the interface un​Assigned​Interface​Identity

Create vFiler using NetApp OnTap

Summary
Create a vFiler using ONTAP
Description
A vFiler is a logical unit of storage. We can manage a single Filer using ONTAP. In this task we create a vFiler using ONTAP.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer in which the new v​Filer need to be created.​ filer​Identity Y
v​Filer Name Enter the Name of the v​Filer to be created.​ gen_​text_​input Y
IP Address Provide IP address range or comma separated IP addresses or both gen_​text_​input Y
Storage Unit Select the Storage Units.​ gen_​text_​input Y
IP Space Name Enter the Name of the IP Space to be used for v​Filer.​ ip​Space​Identity Y
Setup vfiler setup
Subnet Mask Enter Subnet Mask gen_​text_​input Y
DNS Domain Enter DNS Domain gen_​text_​input
DNS Server Addresses Enter list of DNS Server IP Addresses gen_​text_​input
Interface Name Select interface name gen_​text_​input
Default Gateway Enter default gateway gen_​text_​input
Protocols Select the Protocols.​ vfiler​Protocol
Outputs
Output Description Type
VFILER_​NAME Name of the v​Filer gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
VFILER_​IP_​ADDRESS IP Address of the v​Filer on which the selected operation was performed gen_​text_​input
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
IPSPACE_​NAME Name of the IP Space on which the selected operation was performed ip​Space​Name
VLAN_​INTERFACE_​NAME Name of the v​Lan Interface on which the selected operation was performed v​LANinterface​Name
OUTPUT_​VFILER_​INTERFACE_​IDENTITY Identity of the interface which is assigned to vfiler.​ vfiler​Interface​Identity
OUTPUT_​ONTAP_​ALL_​VFILER_​IDENTITY Identity of the All ONTAP vfilers including vfiler0 net​App​ONTAPAll​VFilers​Identity

Delete NetApp Aggregate

Summary
Deletes the selected aggregate
Description
This task will delete the selected aggregate
Inputs
Input Description Mappable To Type Mandatory
Aggregate Name Select an aggregate to be deleted.​ aggregate​Identity Y
Make offline if aggregate is online Select this checkbox for force deletion of aggregate
Outputs
Output Description Type
OUTPUT_​AGGREGATE_​NAME Name of the Aggregate.​ netapp​Aggregate​Name
OUTPUT_​AGGREGATE_​IDENTITY Identity of the Aggregate aggregate​Identity

Delete NetApp IP Space

Summary
Deletes an IP Space.
Description
Destroys selected IP Space. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
IP Space Name Select the IP Space that need to be deleted.​ ip​Space​Identity Y
Force Forcibly Delete.​
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
IPSPACE_​NAME Name of the IP Space on which the selected operation was performed ip​Space​Name
OUTPUT_​IPSPACE_​IDENTITY Identity of the IP Space ip​Space​Identity

Delete NetApp Initiator Group

Summary
Delete an Initiator Group
Description
An Initiator group can be deleted when the LUN that it is mapped to does not have any usage. When deleting an Initiator Group all the initiators within this group are deleted. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Select the Initiator Group that needs to be deleted.​ i​Group​Identity Y
Force Forcibly Delete.​ Boolean
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
INITIATOR_​GROUP_​NAME Name of the Initiator Group on which the selected operation was performed net​App​Initiator​Group​Name
OUTPUT_​IGROUP_​IDENTITY Identity of the i​Group i​Group​Identity

Delete NetApp SnapMirror Schedule

Summary
Deletes Snapmirror Schedule
Description
This task will delete snap mirror schedules
Inputs
Input Description Mappable To Type Mandatory
Destination Location The destination location of the snapmirrored Schedule.​ gen_​text_​input Y
Outputs
No Outputs

Delete NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
Destination Path The secondary path of the snapvault.​ Net​App​Snap​Vault​Identity Y
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity

Delete NetApp vFiler Initiator Group

Summary
Delete an vFiler Initiator Group
Description
An Initiator group can be deleted when the LUN that it is mapped to does not have any usage. When deleting an Initiator Group all the initiators within this group are deleted. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Select the Initiator Group that needs to be deleted.​ v​Filer​IGroup​Identity Y
Force Forcibly Delete.​ Boolean
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VFILER_​INITIATOR_​GROUP_​NAME Name of the vfiler Initiator Group on which the selected operation was performed vfiler​Initiator​Group​Name
OUTPUT_​VFILER_​IGROUP_​IDENTITY Identity of the v​Filer Initiator Group v​Filer​IGroup​Identity

Delete Quota

Summary
Deletes a Quota for the Qtree under the volume.
Description
This task will deletes a quota rule for the QTree under the volume. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select a Volume Allv​Filer​Volume​Identity Y
Qtree Name Select Qtree Name gen_​text_​input Y
Outputs
No Outputs

Delete VLAN Interface

Summary
Deletes a vLAN.
Description
Deletes the selected vLAN.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer from which VLAN Interface need to be deleted.​ filer​Identity Y
Virtual Interface Name Enter the Virtual Interface Name.​ gen_​text_​input Y
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VLAN_​INTERFACE_​NAME Name of the v​Lan Interface on which the selected operation was performed v​LANinterface​Name
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity

Destroy NetApp Flexible Volume

Summary
Delete an existing flexible Volume.
Description
A traditional volume can be resized to a bigger size but cannot be reduced in size. A flexible volume on the other hand can be resized to either a bigger or smaller size. A traditional volume is tightly coupled with its containing aggregate. In order to increase the size of the traditional volume additional disk can be added. A flexible volume is loosely coupled with its containing aggregate and hence size can be increased or decreased. This task is to delete an existing flexible volume. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the Volume that needs to be destroyed.​ volume​Identity Y
Force Forcibly Delete.​
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VOLUME_​NAME Name of the Volume on which the selected operation was performed volume
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity

Destroy NetApp LUN

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be destroyed.​ lun​Identity Y
Force Forcibly Delete.​ Boolean
Outputs
No Outputs

Destroy NetApp QTree

Summary
Destroy a selected QTree under the volume.
Description
Destroy a selected QTree under the volume.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Qtree Name Select Qtree Name v​Filer​Qtree​Identity Y
Force Forcibly Delete.​
Outputs
Output Description Type
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
OUTPUT_​VFILER_​VOLUME_​IDENTITY Identity of the v​Filer Volume v​Filer​Volume​Identity

Destroy NetApp vFiler LUN

Summary
Destroys a vFiler LUN.
Description
This task destroys a vFiler LUN.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be destroyed.​ v​Filer​LUNIdentity Y
Force Forcibly Delete.​ Boolean
Outputs
No Outputs

Destroy NetApp vFiler using OnTap

Summary
Destroy the vfiler permanantly on the storage system using ONTAP.
Description
This task will destroy the selected vfiler permanantly from the storage system.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name v​Filer​Identity Y
Force Forcibly Delete.​
Outputs
No Outputs

Execute NetApp CLI

Summary
An Interface to the Command Line
Description
Executes the CLI command on the filer and returns either true or false based on the output and the expected value. This task will work only for ONTAP accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Filer Identity Name filer​Identity Y
CLI Command Enter CLI Command gen_​text_​input
Expected Output Enter Expected Output gen_​text_​input
Undo CLI Command Enter CLI Command gen_​text_​input
Outputs
Output Description Type
OUTPUT_​NETAPP_​CLI_​OUTPUT Output of Net​App CLI Task.​ gen_​text_​input

Get NetApp partner info

Summary
Gets NetApp partner information
Description
This task will get the partner information of selected filer
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer.​ filer​Identity Y
Outputs
Output Description Type
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​NETAPP_​STORAGE_​PARTNER_​IDENTITY Identity of the Filer partner identity netapp​Storage​Partner​Identity

Map LUN to NetApp Initiator Group

Summary
Map an existing LUN to an existing Initiator Group
Description
Each Initiator under Initiator Group are mapped to individual host nodes. The host node information is stored in the specified LUN which is mapped to this Initiator Group This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Select the Filer.​ filer​Identity Y
Initiator Group Name Select the Initiator Group that will be mapped to the LUN.​ net​App​Initiator​Group​Name Y
Specify LUN ID If not specified, system will generate LUN ID automatically.​
LUN ID LUN ID for LUN lun​Id Y
LUN Path Select the LUN Path that needs to be mapped to the Initiator Group.​ net​App​Lun​Path Y
Outputs
Output Description Type
INITIATOR_​GROUP_​NAME Name of the Initiator Group on which the selected operation was performed net​App​Initiator​Group​Name
LUN_​ID ID of the LUN gen_​text_​input
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
LUN_​IDENTITY Identity of the LUN lun​Identity
OUTPUT_​IGROUP_​IDENTITY Identity of the i​Group i​Group​Identity

Map NetApp vFiler LUN to Initiator Group

Summary
Map an existing LUN in vfiler to an existing Initiator Group in vfiler
Description
Each Initiator under Initiator Group is mapped to individual host nodes. The host node information is stored in the specified LUN which is mapped to this Initiator Group This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Initiator Group Name v​Filer​IGroup​Identity Y
Specify LUN ID If not specified, system will generate LUN ID automatically.​
LUN ID LUN ID for LUN lun​Id
LUN Path Select the LUN Path that needs to be mapped to the Initiator Group.​ net​App​Lun​Path Y
Outputs
Output Description Type
VFILER_​INITIATOR_​GROUP_​NAME Name of the vfiler Initiator Group on which the selected operation was performed vfiler​Initiator​Group​Name
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​VFILER_​IGROUP_​IDENTITY Identity of the v​Filer Initiator Group v​Filer​IGroup​Identity
OUTPUT_​VFILER_​LUN_​IDENTITY Identity of the v​Filer LUN v​Filer​LUNIdentity

Modify NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
Primary System Select the Primay Device Name.​ filer​Identity Y
Destination Path Select the Destination Path for which Source Path should be changed.​ net​App​Destination​Path Y
Primary Path Select the Source Path net​App​QTree​Identity Y
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity

Modify NetApp Volume Status

Summary
Modify the status of selected flexible Volume
Description
This task can modify the status of any flexible volume. It can be used to bring the volume online or take it offline.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the volume to modify status Allv​Filer​Volume​Identity Y
Online Select checkbox to bring the volume Online NETAPP_​VOLUME_​STATUS
Outputs
Output Description Type
OUTPUT_​VFILER_​VOLUME_​IDENTITY Identity of the v​Filer Volume v​Filer​Volume​Identity
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​ACCOUNT_​IDENTITY Identity of the Account gen_​text_​input

Move NetApp LUN

Summary
Changing the LUN Path within Volume
Description
This task is for changing the LUN Path within the Volume This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be Moved.​ lun​Identity Y
LUN Name Enter the New LUN Name.​ lun​Dest​Name Y
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
LUN_​IDENTITY Identity of the LUN lun​Identity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity

NetApp SnapMirror Destination Actions

Summary
Perform snapmirror action like Initialize, Break, Quiesce, Resume, Resync on destination location volume.
Description
This task will support multiple actions on snapmirror destination volume. Based on the input selection of action type, appropriate action will be executed. Initialize - Starts an initial transfer over the network for a specific destination. Break - Breaks a snapmirrored relationship. No checking on whether the operation is legal, or whether it is successful. Result will be updated after the inventory collected in this task. Quiesce - Pauses transfer to the destination. Resume - Resumes transfers to the destination that were quisced. Resync - Kicks off a resync of a broken snapmirrored pair.
Inputs
Input Description Mappable To Type Mandatory
Destination Location The destination location of the snapmirrored pair to perform action.​ net​App​Allv​Filers​Snapmirror​Destination​Identity Y
Select Action Select action to be performed on the destination location.​ gen_​text_​input Y
Outputs
No Outputs

Persist NetApp Network Configuration

Summary
Persists all filer network configurations in a file.
Description
This task will write and persists all network interface configurations in to a filers /etc/rc file. So that network configuration settings will not loose when the filer restarts. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Filer Identity Name Filer Identity Name gen_​text_​input Y
Outputs
No Outputs

Release NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
Destination Path The secondary path of the snapvault.​ Net​App​Snap​Vault​Identity Y
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity

Remove IP Address from NetApp vFiler

Summary
Remove selected IP Address which are assigned to a vFiler.
Description
This task will remove the selected IP Address from the list of IP's that are configured network traffic for a vfiler. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name gen_​text_​input Y
IP Address Select IP Address for the selected v​Filer.​ gen_​text_​input
Outputs
Output Description Type
VFILER_​NAME Name of the v​Filer gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity
VFILER_​IP_​ADDRESS IP Address of the v​Filer on which the selected operation was performed gen_​text_​input

Remove NetApp CIFS Volume Share

Summary
Removes the sharing of volume resource.
Description
This task will removes the configured CIFS volume share for the selected volume.This task will work only for ONTAP accounts.
Inputs
Input Description Mappable To Type Mandatory
Select Filer/v​Filer Volume Select Filer Name or v​Filer Name v​Filer​CIFSVolume​Identity Y
Share Name Select Share Path gen_​text_​input Y
Outputs
No Outputs

Remove NetApp Initiator from Initiator Group

Summary
Remove an Initiator from an Initiator Group
Description
Remove the Initiator from the Initiator Group. Once removed the host node will not be able to access the LUN. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Select the Initiator Group from which an Initiator needs to be deleted.​ i​Group​Identity Y
Initiator Name Select the Initiator that needs to be deleted.​ gen_​text_​input Y
Force Forcibly Delete.​
Outputs
Output Description Type
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​IGROUP_​IDENTITY Identity of the i​Group i​Group​Identity

Remove NetApp QTree NFS Export

Summary
Removes a NFS export rule for QTree.
Description
This task will deleted a NFS Export rule which is created for the QTree. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Actual Path Enter the actual path mounted when the NFS client mounts the exported path.​ v​Filer​Qtree​Identity Y
Force Forcibly Delete.​
Outputs
No Outputs

Remove NetApp Volume NFS Export

Summary
Removes NFS export rule for the volume in the storage system using ONTAP.
Description
This task will remove a NFS export rule for the volume.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Actual Path Enter the actual path mounted when the NFS client mounts the exported path.​ Allv​Filer​Volume​Identity Y
Force Forcibly Delete.​
Outputs
No Outputs

Remove NetApp vFiler Initiator from Initiator Group

Summary
Remove an Initiator from an vFiler Initiator Group
Description
Remove the Initiator from the Initiator Group. Once removed the host node will not be able to access the LUN. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Initiator Group Name Select the Initiator Group from which an Initiator needs to be deleted.​ v​Filer​IGroup​Identity Y
Initiator Name Select the Initiator that needs to be deleted.​ gen_​text_​input Y
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VFILER_​INITIATOR_​GROUP_​NAME Name of the vfiler Initiator Group on which the selected operation was performed vfiler​Initiator​Group​Name
VFILER_​INITIATOR_​_​NAME Name of the vfiler Initiator on which the selected operation was performed vfiler​Initiator
OUTPUT_​VFILER_​IGROUP_​IDENTITY Identity of the v​Filer Initiator Group v​Filer​IGroup​Identity

Remove NetApp vFiler NFS Volume Export

Summary
Remove vFiler NFS Volume Export
Description
Removes the NFS rule for the pathname.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name v​Filer​Identity Y
Export Path Enter the path that will be exported to NFS clients.​ gen_​text_​input Y
Outputs
No Outputs

Remove Storage from NetApp vFiler

Summary
Remove Storage components from vFiler.
Description
Remove existing Storage components from vFiler like Volumes, LUNs, Qtrees etc.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select the v​Filer from which Storage need to be removed.​ gen_​text_​input Y
Storage Path Enter the Path of the storage that needs to removed.​ volume Y
Force Force destroy?
Outputs
Output Description Type
VFILER_​NAME Name of the v​Filer vfiler​Name
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity

Resize NetApp Flexible Volume

Summary
Resize an existing flexible volume.
Description
To increase/decrease the capacity of a flexible volume user needs to mention the required size of the flexible volume. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the Volume that need to be Resized.​ volume​Identity Y
Volume Size Enter the new Volume Size.​ net​App​Vol​Size Y
Volume Size Units Enter the Volume Size Units.​ size​Unit Y
Outputs
Output Description Type
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
VOLUME_​NAME Name of the Volume on which the selected operation was performed volume
OUTPUT_​VOLUME_​IDENTITY Identity of the Volume volume​Identity
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity
OUTPUT_​ONCOMMAND_​FILER_​IDENTITY Identity of the On​Command Filer dfm​Filer​Identity

Resize NetApp LUN

Summary
Resize the LUN size within volume
Description
This task is for resizing the LUN size within the volume This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be Resized.​ lun​Identity Y
LUN Size Enter the New LUN Resize Value net​App​Lun​Size Y
LUN Size Units Select the LUN Size Units.​ size​Unit Y
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
LUN_​IDENTITY Identity of the LUN lun​Identity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity

Resize NetApp vFiler LUN

Summary
Resizes a vFiler LUN.
Description
This task resizes a vFiler LUN.This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be Resized.​ v​Filer​LUNIdentity Y
LUN Size Enter the New LUN Resize Value net​App​Lun​Size Y
LUN Size Units Select the LUN Size Units.​ size​Unit Y
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
OUTPUT_​VFILER_​LUN_​IDENTITY Identity of the v​Filer LUN v​Filer​LUNIdentity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity

Resize NetApp vFiler Volume

Summary
Resizes vFiler volume
Description
This task will resize selected vFiler volume to specified new size
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the v​Filer Volume that need to be resized.​ v​Filer​Volume​Identity Y
Volume Size Enter the new Volume Size.​ net​App​Vol​Size Y
Volume Size Units Select the Volume Size Units.​ size​Unit
Outputs
Output Description Type
OUTPUT_​VFILER_​VOLUME_​IDENTITY Identity of the v​Filer Volume v​Filer​Volume​Identity

Resize VM Datastore(NetApp)

Summary
Selected VMware VM's Datastore can be resized using VSC.
Description
This task resizes the datastore which is associated for the selected VM in the vCenter server and is mapped the storage target either NFS Volume or VMFS LUN to the Storage system by the VSC pluggined to the vCenter Server. we can either increase or decrease the datastore of type NFS exported as volume, but the we cannot decrease the datatstore of type VMFS mapped to storage target as LUN.
Inputs
Input Description Mappable To Type Mandatory
Select VM Optionally select a VM for resizing the storage on vm Y
Datastore Name Select a Datastore Name.​ data​Store​Name
Storage Size (GB) Enter the size of Storage.​ data​Store​Size Y
Outputs
Output Description Type
OUTPUT_​DATASTORE_​NAME Datastore name data​Store​Name

Restore NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
Snapvault to Restore Select Snapvault to restore.​ Net​App​Snap​Vault​Identity Y
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity

Set NetApp CIFS Volume Share Access

Summary
Makes the volume shareable by CIFS access
Description
This task will make the volume sharable by CIFS access
Inputs
Input Description Mappable To Type Mandatory
Volume Name Select the Volume in which CIFS share to be created v​Filer​CIFSVolume​Identity Y
Share Name Enter Share Path cifs​Share​Name Y
Select Role Select role to provide permission for cifs share directory.​ net​App​Cifs​Role
Role ID Enter domain user name or group name.​ gen_​text_​input Y
Domain Name Enter domain name.​ gen_​text_​input
Access Type Select type of access permissions.​ net​App​Cifs​Access
Description Enter share description
Outputs
No Outputs

Setup NetApp CIFS on vFiler

Summary
Setup filer/vfiler CIFS service.
Description
This task will configure the filer/vfiler's CIFS service. The CIFS service will start automatically once this task completes successfully.
Inputs
Input Description Mappable To Type Mandatory
v​Filer Name Select v​Filer Name net​App​ONTAPAll​VFilers​Identity Y
Authentication Select Authentication style gen_​text_​input
Security Style Select Secuirty style gen_​text_​input
DNS Domain Name Enter name of the domain that the CIFS server will join gen_​text_​input Y
Login User The name of a domain user that has the ability to add the CIFS server to the domain given in domain-name gen_​text_​input Y
Login Password The password for login-user password Y
Organizational Unit The distinguished name of the organizational unit gen_​text_​input
Site Name The name of the site CIFS service will become member gen_​text_​input
v​Filer Root Password The password for root user under v​Filer password Y
Outputs
Output Description Type
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity

Unmap NetApp LUN from Initiator Group

Summary
Un-map the LUN from the Initiator Group.
Description
Once the LUN is unmapped from the initiator group, the host node information stored in the LUN is no longer accessible. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be Unmapped from the Initiator Group.​ lun​Identity Y
Initiator Group Name Select the Initiator Group.​ net​App​Initiator​Group​Name Y
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
INITIATOR_​GROUP_​NAME Name of the Initiator Group on which the selected operation was performed net​App​Initiator​Group​Name
LUN_​IDENTITY Identity of the LUN lun​Identity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​FILER_​IDENTITY Identity of the Filer filer​Identity

Unmap NetApp vFiler LUN from Initiator Group

Summary
Un-Map the LUN from the Initiator Group.
Description
Once the LUN is unmapped from the initiator group, the host node information stored in the LUN is no longer accessible. This task will work for both ONTAP and OnCommand accounts.
Inputs
Input Description Mappable To Type Mandatory
LUN Name Select the LUN that needs to be Unmapped from the Initiator Group.​ v​Filer​LUNIdentity Y
Initiator Group Name Select the Initiator Group.​ vfiler​Initiator​Group​Name Y
Outputs
Output Description Type
LUN_​PATH Path of the LUN on which the selected operation was performed net​App​Lun​Path
VFILER_​INITIATOR_​GROUP Name of the vfiler Initiator Group on which the selected operation was performed vfiler​Initiator​Group
OUTPUT_​VFILER_​LUN_​IDENTITY Identity of the v​Filer LUN v​Filer​LUNIdentity
DATACENTER Name of the Datacenter on which the selected operation was performed datacenter​Name
ACCOUNT_​NAME Name of the Account on which the selected operation was performed netapp​Account​Name
FILER_​NAME Name/IP Address of the Filer on which the selected operation was performed gen_​text_​input
OUTPUT_​VFILER_​IDENTITY Identity of the v​Filer v​Filer​Identity

Update NetApp SnapVault

Summary
Description
Inputs
Input Description Mappable To Type Mandatory
Destination Path The destination path of the snapvault.​ Net​App​Snap​Vault​Identity Y
Outputs
Output Description Type
OUTPUT_​NETAPP_​SNAPVAULT_​IDENTITY Net​App Snapvault Identity.​ Net​App​Snap​Vault​Identity