Configuring IPv6 Client IP Address Learning

Prerequisites for IPv6 Client Address Learning

Before configuring IPv6 client address learning, configure the wireless clients to support IPv6.

Information About IPv6 Client Address Learning

Client Address Learning is configured on switch to learn the wireless client's IPv4 and IPv6 address and clients transition state maintained by the switch on an association, re-association, de-authentication and timeout.

There are three ways for IPv6 client to acquire IPv6 addresses:

  • Stateless Address Auto-Configuration (SLACC)

  • Stateful DHCPv6

  • Static Configuration

For all of these methods, the IPv6 client always sends neighbor solicitation DAD (Duplicate Address Detection) request to ensure there is no duplicate IP address on the network. The switch snoops the client's NDP and DHCPv6 packets to learn about its client IP addresses.

SLAAC Address Assignment

The most common method for IPv6 client address assignment is Stateless Address Auto-Configuration (SLAAC). SLAAC provides simple plug-and-play connectivity where clients self-assign an address based on the IPv6 prefix. This process is achieved

Stateless Address Auto-Configuration (SLAAC) is configured as follows:

  • Host sends a router solicitation message.
  • Hosts waits for a Router Advertisement message.
  • Hosts take the first 64 bits of the IPv6 prefix from the Router Advertisement message and combines it with the 64 bit EUI-64 address (in the case of ethernet, this is created from the MAC Address) to create a global unicast message. The host also uses the source IP address, in the IP header, of the Router Advertisement message, as its default gateway.
  • Duplicate Address Detection is performed by IPv6 clients in order to ensure that random addresses that are picked do not collide with other clients.
  • The choice of algorithm is up to the client and is often configurable.

The last 64 bits of the IP v6 address can be learned based on the following 2 algorithms:

  • EUI-64 which is based on the MAC address of the interface, or
  • Private addresses that are randomly generated.
Figure 1. SLAAC Address Assignment


The following Cisco IOS configuration commands from a Cisco-capable IPv6 router are used to enable SLAAC addressing and router advertisements:

ipv6 unicast-routing
interface Vlan20
description IPv6-SLAAC
ip address 192.168.20.1 255.255.255.0
ipv6 address FE80:DB8:0:20::1 linklocal
ipv6 address 2001:DB8:0:20::1/64
ipv6 enable
end

Stateful DHCPv6 Address Assignment

Figure 2. Stateful DHCPv6 Address Assignment

The use of DHCPv6 is not required for IPv6 client connectivity if SLAAC is already deployed. There are two modes of operation for DHCPv6 called Stateless and Stateful.

The DHCPv6 Stateless mode is used to provide clients with additional network information that is not available in the router advertisement, but not an IPv6 address as this is already provided by SLAAC. This information can include the DNS domain name, DNS server(s), and other DHCP vendor-specific options. This interface configuration is for a Cisco IOS IPv6 router implementing stateless DHCPv6 with SLAAC enabled:

ipv6 unicast-routing
ipv6 dhcp pool IPV6_DHCPPOOL
address prefix 2001:db8:5:10::/64
domain-name cisco.com
dns-server 2001:db8:6:6::1
interface Vlan20
description IPv6-DHCP-Stateless
ip address 192.168.20.1 255.255.255.0
ipv6 nd other-config-flag
ipv6 dhcp server IPV6_DHCPPOOL
ipv6 address 2001:DB8:0:20::1/64
end

The DHCPv6 Stateful option, also known as managed mode, operates similarly to DHCPv4 in that it assigns unique addresses to each client instead of the client generating the last 64 bits of the address as in SLAAC. This interface configuration is for a Cisco IOS IPv6 router implementing stateful DHCPv6 on a local Switch:

ipv6 unicast-routing
ipv6 dhcp pool IPV6_DHCPPOOL
address prefix 2001:db8:5:10::/64
domain-name cisco.com
dns-server 2001:db8:6:6::1
interface Vlan20
description IPv6-DHCP-Stateful
ip address 192.168.20.1 255.255.255.0
ipv6 address 2001:DB8:0:20::1/64
ipv6 nd prefix 2001:DB8:0:20::/64 no-advertise
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
ipv6 dhcp server IPV6_DHCPPOOL
end

This interface configuration is for a Cisco IOS IPv6 router implementing stateful DHCPv6 on an external DHCP server:

ipv6 unicast-routing
domain-name cisco.com
dns-server 2001:db8:6:6::1
interface Vlan20
description IPv6-DHCP-Stateful
ip address 192.168.20.1 255.255.255.0
ipv6 address 2001:DB8:0:20::1/64
ipv6 nd prefix 2001:DB8:0:20::/64 no-advertise
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
ipv6 dhcp_relay destination 2001:DB8:0:20::2
end

Static IP Address Assignment

Statically configured address on a client.

Router Solicitation

A Router Solicitation message is issued by a host controller to facilitate local routers to transmit Router Advertisement from which it can obtain information about local routing or perform Stateless Auto-configuration. Router Advertisements are transmitted periodically and the host prompts with an immediate Router Advertisement using a Router Solicitation such as - when it boots or following a restart operation.

Router Advertisement

A Router Advertisement message is issued periodically by a router or in response to a Router Solicitation message from a host. The information contained in these messages is used by hosts to perform Stateless Auto-configuration and to modify its routing table.

Neighbor Discovery

IPv6 Neighbor Discovery is a set of messages and processes that determine relationships between neighboring nodes. Neighbor Discovery replaces ARP, ICMP Router Discovery, and ICMP Redirect used in IPv4.

IPv6 Neighbor Discovery inspection analyzes neighbor discovery messages in order to build a trusted binding table database, and IPv6 neighbor discovery packets that do not comply are dropped. The neighbor binding table in the switch tracks each IPv6 address and its associated MAC address. Clients are expired from the table according to Neighbor Binding timers.

Neighbor Discovery Suppression

The IPv6 addresses of wireless clients are cached by the switch. When the switch receives an NS multicast looking for an IPv6 address, and if the target address is known to the switch and belongs to one of its clients, the switch will reply with an NA message on behalf of the client. The result of this process generates the equivalent of the Address Resolution Protocol (ARP) table of IPv4 but is more efficient - uses generally fewer messages.


Note

The switch acts like proxy and respond with NA, only when the ipv6 nd suppress command is configured

If the switch does not have the IPv6 address of a wireless client, the switch will not respond with NA and forward the NS packet to the wireless side. To resolve this, an NS Multicast Forwarding knob is provided. If this knob is enabled, the switch gets the NS packet for the IPv6 address that it does not have (cache miss) and forwards it to the wireless side. This packet reaches the intended wireless client and the client replies with NA.

This cache miss scenario occurs rarely, and only very few clients which do not implement complete IPv6 stack may not advertise their IPv6 address during NDP.

RA Guard

IPv6 clients configure IPv6 addresses and populate their router tables based on IPv6 router advertisement (RA) packets. The RA guard feature is similar to the RA guard feature of wired networks. RA guard increases the security of the IPv6 network by dropping the unwanted or rogue RA packets that come from wireless clients. If this feature is not configured, malicious IPv6 wireless clients announce themselves as the router for the network often with high priority, which would take higher precedence over legitimate IPv6 routers.

RA-Guard also examines the incoming RA's and decides whether to switch or block them based solely on information found in the message or in the switch configuration. The information available in the frames received is useful for RA validation:
  • Port on which the frame is received

  • IPv6 source address

  • Prefix list

The following configuration information created on the switch is available to RA-Guard to validate against the information found in the received RA frame:

  • Trusted/Untrusted ports for receiving RA-guard messages

  • Trusted/Untrusted IPv6 source addresses of RA-sender

  • Trusted/Untrusted Prefix list and Prefix ranges

  • Router Preference

RA guard occurs at the switch. You can configure the switch to drop RA messages at the switch. All IPv6 RA messages are dropped, which protects other wireless clients and upstream wired network from malicious IPv6 clients.

//Create a policy for RA Guard//
ipv6 nd raguard policy raguard-router
trusted-port
device-role router
//Applying the RA Guard Policy on port/interface//
interface tengigabitethernet1/0/1 (Katana)
interface gigabitethernet1/0/1 (Edison)

ipv6 nd raguard attach-policy raguard-router

RA Throttling

RA throttling allows the controller to enforce limits to RA packets headed toward the wireless network. By enabling RA throttling, routers that send many RA packets can be trimmed to a minimum frequency that will still maintain an IPv6 client connectivity. If a client sends an RS packet, an RA is sent back to the client. This RA is allowed through the controller and unicasted to the client. This process ensures that the new clients or roaming clients are not affected by the RA throttling.

Configuring IPv6 Unicast (CLI)

IPv6 unicasting must always be enabled on the switch and the controller. IPv6 unicast routing is disabled.

Before you begin

To enable the forwarding of IPv6 unicast datagrams, use the ipv6 unicast-routing command in global configuration mode. To disable the forwarding of IPv6 unicast datagrams, use the no form of this command.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

ipv6 unicast routing

Example:

Switch (config)# ipv6 unicast routing
enable the forwarding of IPv6 unicast datagrams

Configuring RA Guard Policy (CLI)

Configure RA Guard policy on the switch to add IPv6 client addresses and populate the router table based on IPv6 router advertisement packets.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

ipv6 nd raguard policy raguard-router

Example:

Switch(config)# ipv6 nd raguard policy raguard-router
Defines the RA guard policy name and enters RA guard policy configuration mode.
Step 3

trustedport

Example:

Switch(config-ra-guard)# trustedport
(Optional) Specifies that this policy is being applied to trusted ports.
Step 4

device-role router

Example:

Switch(config-ra-guard)# device-role router
Specifies the role of the device attached to the port.
Step 5

exit

Example:

Switch(config-ra-guard)# exit
Exits RA guard policy configuration mode and returns to global configuration mode.

Applying RA Guard Policy (CLI)

Applying the RA Guard policy on the switch will block all the untrusted RA's.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

interface tengigabitethernet 1/0/1

Example:

Switch (config)# interface tengigabitethernet 1/0/1
Specifies an interface type and number, and places the device in interface configuration mode.
Step 3

ipv6 nd raguard attach-policy raguard-router

Example:

Switch(config-if)# ipv6 nd raguard attach-policy raguard-router
Applies the IPv6 RA Guard feature to a specified interface.
Step 4

exit

Example:

Switch(config-if)# exit
Exits interface configuration mode.

Configuring RA Throttle Policy (CLI)

Configure RA Throttle policy to allow the enforce the limits

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

ipv6 nd ra-throttler policy ra-throttler1

Example:

Switch(config)# ipv6 nd ra-throttler policy ra-throttler1
Define the router advertisement (RA) throttler policy name and enter IPv6 RA throttle policy configuration mode.
Step 3

throttleperiod 500

Example:

Switch(config-nd-ra-throttle)# throttleperiod 500
Configures the throttle period in an IPv6 RA throttler policy.
Step 4

max-through 10

Example:

Switch(config-nd-ra-throttle)# max-through 500
Limits multicast RAs per VLAN per throttle period.
Step 5

allow-atleast 5 at-most 10

Example:

Switch(config-nd-ra-throttle)# allow-atleast 5 at-most 10
Limits the number of multicast RAs per device per throttle period in an RA throttler policy.

Applying RA Throttle Policy on VLAN (CLI)

Applying the RA Throttle policy on a VLAN. By enabling RA throttling, routers that send many RA packets can be trimmed to a minimum frequency that will still maintain an IPv6 client connectivity.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

vlan configuration 1

Example:

Switch(config)# vlan configuration 1
Configures a VLAN or a collection of VLANs and enters VLAN configuration mode.
Step 3

ipv6 nd ra throttler attach-policy ra-throttler1

Example:

Switch(config-vlan)# ipv6 nd ra throttler attach-policy ra-throttler1
Attaches an IPv6 RA throttler policy to a VLAN or a collection of VLANs.

Configuring IPv6 Snooping (CLI)

IPv6 snooping must always be enabled on the switch and the controller.

Before you begin

Enable IPv6 on the client machine.

Procedure

  Command or Action Purpose
Step 1

vlan configuration 1

Example:

Switch(config)# vlan configuration 1

Enters Vlan configuration mode.

Step 2

ipv6 snooping

Example:


Switch(config-vlan)# ipv6 snooping

Enables IPv6 snooping on the Vlan.

Step 3

ipv6 nd suppress

Example:


Switch(config-vlan-config)# ipv6 nd suppress

Enables the IPv6 ND suppress on the Vlan.

Step 4

exit

Example:

Switch(config-vlan-config)# exit

Saves the configuration and comes out of the Vlan configuration mode.

Configuring IPv6 ND Suppress Policy (CLI)

The IPv6 neighbor discovery (ND) multicast suppress feature stops as many ND multicast neighbor solicit (NS) messages as possible by dropping them (and responding to solicitations on behalf of the targets) or converting them into unicast traffic. This feature runs on a layer 2 switch or a wireless controller and is used to reduce the amount of control traffic necessary for proper link operations.

When an address is inserted into the binding table, an address resolution request sent to a multicast address is intercepted, and the device either responds on behalf of the address owner or, at layer 2, converts the request into a unicast message and forwards it to its destination.

Procedure

  Command or Action Purpose
Step 1

enable

Example:

Switch(config)# enable
Enables privileged EXEC mode.
  • Enter your password if prompted.
Step 2

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 3

ipv6 nd suppress policy

Example:

Switch (config)# ipv6 nd suppress policy

Defines the ND suppress policy name and enters ND suppress policy configuration mode.

Configuring IPv6 Snooping on VLAN/PortChannel

Neighbor Discover (ND) suppress can be enabled or disabled on either the VLAN or a switchport.

Before you begin

Procedure

  Command or Action Purpose
Step 1

vlan config901

Example:

Switch(config)# vlan config901
Creates a VLAN and enter the VLAN configuration mode
Step 2

ipv6 nd suppress

Example:

Switch(config-vlan)# ipv6 nd suppress
Applies the IPv6 nd suppress on VLAN.
Step 3

end

Example:

Switch(config-vlan)# end
Exits vlan configuration mode and enters the global configuration mode.
Step 4

interface gi1/0/1

Example:

Switch (config)# interface gi1/0/1

Creates a gigabitethernet port interface.

Step 5

ipv6 nd suppress

Example:

Switch(config-vlan)# ipv6 nd suppress
Applies the IPv6 nd suppress on the interface.
Step 6

end

Example:

Switch(config-vlan)# end
Exits vlan configuration mode and enters the global configuration mode.

Configuring IPv6 on Switch (CLI)

Use this configuration example to configure IPv6 on an interface.

Before you begin

Enable IPv6 on the client and IPv6 support on the wired infrastructure.

Procedure

  Command or Action Purpose
Step 1

interface vlan 1

Example:

Switch(config)# interface vlan 1

Creates a interface and enters interface configuration mode.

Step 2

ip address fe80::1 link-local

Example:

Switch(config-if)# ip address 198.51.100.1 255.255.255.0
   Switch(config-if)# ipv6 address fe80::1 link-local
   Switch(config-if)# ipv6 address 2001:DB8:0:1:FFFF:1234::5/64 
   Switch(config-if)# ipv6 address 2001:DB8:0:0:E000::F/64

Configures IPv6 address on the interface using the link-local option.

Step 3

ipv6 enable

Example:

Switch(config)# ipv6 enable

(Optional) Enables IPv6 on the interface.

Step 4

end

Example:

Switch(config)# end

Exits from the interface mode.

Configuring DHCP Pool (CLI)

Procedure

  Command or Action Purpose
Step 1

ipv6 dhcp pool Vlan21

Example:

Switch(config)# ipv6 dhcp pool vlan1

Enters the configuration mode and configures the IPv6 DHCP pool on the Vlan.

Step 2

address prefix 2001:DB8:0:1:FFFF:1234::/64 lifetime 300 10

Example:

Switch(config-dhcpv6)# address prefix 2001:DB8:0:1:FFFF:1234::/64 lifetime 300 10

Enters the configuration-dhcp mode and configures the address pool and its lifetime on a Vlan.

Step 3

dns-server 2001:100:0:1::1

Example:

Switch(config-dhcpv6)# dns-server 2001:20:21::1

Configures the DNS servers for the DHCP pool.

Step 4

domain-name example.com

Example:

Switch(config-dhcpv6)# domain-name example.com

Configures the domain name to complete unqualified host names.

Step 5

end

Example:

Switch(config)# end

Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Configuring Stateless Auto Address Configuration Without DHCP (CLI)

Procedure

  Command or Action Purpose
Step 1

interface vlan 1

Example:

Switch(config)# interface vlan 1

Creates a interface and enters interface configuration mode.

Step 2

ip address fe80::1 link-local

Example:

Switch(config-if)# ip address 198.51.100.1 255.255.255.0
   Switch(config-if)# ipv6 address fe80::1 link-local
   Switch(config-if)# ipv6 address 2001:DB8:0:1:FFFF:1234::5/64 
   Switch(config-if)# ipv6 address 2001:DB8:0:0:E000::F/64

Configures IPv6 address on the interface using the link-local option.

Step 3

ipv6 enable

Example:

Switch(config)# ipv6 enable

(Optional) Enables IPv6 on the interface.

Step 4

no ipv6 nd managed-config-flag

Example:

Switch(config)#interface vlan 1
Switch(config-if)# no ipv6 nd managed-config-flag

Ensures the attached hosts do not use stateful autoconfiguration to obtain addresses.

Step 5

no ipv6 nd other-config-flag

Example:

Switch(config-if)# no ipv6 nd other-config-flag 

Ensures the attached hosts do not use stateful autoconfiguration to obtain non-address options from DHCP (domain etc).

Step 6

end

Example:

Switch(config)# end

Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Configuring Stateless Auto Address Configuration With DHCP (CLI)

Procedure

  Command or Action Purpose
Step 1

interface vlan 1

Example:

Switch(config)# interface vlan 1

Creates a interface and enters interface configuration mode.

Step 2

ip address fe80::1 link-local

Example:

Switch(config-if)# ip address 198.51.100.1 255.255.255.0
   Switch(config-if)# ipv6 address fe80::1 link-local
   Switch(config-if)# ipv6 address 2001:DB8:0:1:FFFF:1234::5/64 
   Switch(config-if)# ipv6 address 2001:DB8:0:0:E000::F/64

Configures IPv6 address on the interface using the link-local option.

Step 3

ipv6 enable

Example:

Switch(config)# ipv6 enable

(Optional) Enables IPv6 on the interface.

Step 4

no ipv6 nd managed-config-flag

Example:

Switch(config)#interface vlan 1
Switch(config-if)# no ipv6 nd managed-config-flag

Ensures the attached hosts do not use stateful autoconfiguration to obtain addresses.

Step 5

ipv6 nd other-config-flag

Example:

Switch(config-if)# no ipv6 nd other-config-flag 

Ensures the attached hosts do not use stateful autoconfiguration to obtain non-address options from DHCP (domain etc).

Step 6

end

Example:

Switch(config)# end

Exits from the interface mode.

Configuring Stateful DHCP Locally (CLI)

This interface configuration is for a Cisco IOS IPv6 router implementing stateful DHCPv6 on a local Switch

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

ipv6 unicast-routing

Example:

Switch(config)# ipv6 unicast-routing

Configures IPv6 for unicasting.

Step 3

ipv6 dhcp pool IPv6_DHCPPOOL

Example:

Switch (config)# ipv6 dhcp pool IPv6_DHCPPOOL

Enters the configuration mode and configures the IPv6 DHCP pool on the VLAN.

Step 4

address prefix 2001:DB8:0:1:FFFF:1234::/64

Example:

Switch (config-dhcpv6)# address prefix
2001:DB8:0:1:FFFF:1234::/64

Specifies the address range to provide in the pool.

Step 5

dns-server 2001:100:0:1::1

Example:

Switch (config-dhcpv6)# dns-server 2001:100:0:1::1

Provides the DNS server option to DHCP clients.

Step 6

domain-name example.com

Example:

Switch (config-dhcpv6)# domain-name example.com

Provides the domain name option to DHCP clients.

Step 7

exit

Example:

Switch (config-dhcpv6)# exit

Returns to the previous mode.

Step 8

interface vlan1

Example:

Switch (config)# interface vlan 1

Enters the interface mode to configure the stateful DHCP.

Step 9

description IPv6-DHCP-Stateful

Example:

Switch (config-if)# description IPv6-DHCP-Stateful

Enter description for the stateful IPv6 DHCP.

Step 10

ipv6 address 2001:DB8:0:20::1/64

Example:

Switch (config-if)# ipv6 address 2001:DB8:0:20::1/64

Enters the IPv6 address for the stateful IPv6 DHCP.

Step 11

ip address 192.168.20.1 255.255.255.0

Example:

Switch (config-if)# ip address 192.168.20.1 255.255.255.0

Enters the IPv6 address for the stateful IPv6 DHCP.

Step 12

ipv6 nd prefix 2001:db8::/64 no-advertise

Example:

Switch (config-if)# ipv6 nd prefix 2001:db8::/64
no-advertise

Configures the IPv6 routing prefix advertisement that must not be advertised.

Step 13

ipv6 nd managed-config-flag

Example:

Switch (config-if)# ipv6 nd managed-config-flag

Configures IPv6 interfaces neighbor discovery to allow the hosts to uses DHCP for address configuration.

Step 14

ipv6 nd other-config-flag

Example:

Switch (config-if)# ipv6 nd other-config-flag

Configures IPv6 interfaces neighbor discovery to allow the hosts to uses DHCP for non-address configuration.

Step 15

ipv6 dhcp server IPv6_DHCPPOOL

Example:

Switch (config-if)# ipv6 dhcp server IPv6_DHCPPOOL

Configures the DHCP server on the interface.

Configuring Stateful DHCP Externally (CLI)

This interface configuration is for a Cisco IOS IPv6 router implementing stateful DHCPv6 on an external DHCP server.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Switch# configure terminal

Enters the global configuration mode.

Step 2

ipv6 unicast-routing

Example:

Switch(config)# ipv6 unicast-routing

Configures the IPv6 for unicasting.

Step 3

dns-server 2001:100:0:1::1

Example:

Switch (config-dhcpv6)# dns-server 2001:100:0:1::1

Provides the DNS server option to DHCP clients.

Step 4

domain-name example.com

Example:

Switch (config-dhcpv6)# domain-name example.com

Provides the domain name option to DHCP clients.

Step 5

exit

Example:

Switch (config-dhcpv6)# exit

Returns to the previous mode.

Step 6

interface vlan1

Example:

Switch (config)# interface vlan 1

Enters the interface mode to configure the stateful DHCP.

Step 7

description IPv6-DHCP-Stateful

Example:

Switch (config-if)# description IPv6-DHCP-Stateful

Enter description for the stateful IPv6 DHCP.

Step 8

ipv6 address 2001:DB8:0:20::1/64

Example:

Switch (config-if)# ipv6 address 2001:DB8:0:20::1/64

Enters the IPv6 address for the stateful IPv6 DHCP.

Step 9

ip address 192.168.20.1 255.255.255.0

Example:

Switch (config-if)# ip address 192.168.20.1 255.255.255.0

Enters the IPv6 address for the stateful IPv6 DHCP.

Step 10

ipv6 nd prefix 2001:db8::/64 no-advertise

Example:

Switch (config-if)# ipv6 nd prefix 2001:db8::/64
no-advertise

Configures the IPv6 routing prefix advertisement that must not be advertised.

Step 11

ipv6 nd managed-config-flag

Example:

Switch (config-if)# ipv6 nd managed-config-flag

Configures IPv6 interfaces neighbor discovery to allow the hosts to uses DHCP for address configuration.

Step 12

ipv6 nd other-config-flag

Example:

Switch (config-if)# ipv6 nd other-config-flag

Configures IPv6 interfaces neighbor discovery to allow the hosts to uses DHCP for non-address configuration.

Step 13

ipv6 dhcp_relay destination 2001:DB8:0:20::2

Example:

Switch (config-if)# ipv6 dhcp_relay destination 2001:DB8:0:20::2

Configures the DHCP server on the interface.

Monitoring IPv6 Clients (GUI)

To view the IPv6 clients associated with the Switch

Procedure


Select Monitor > Clients

The Clients page is displayed. The Clients page contains the following details:

  • Client MAC Address— Displays the MAC address of the client.
  • AP Name— Displays the access point name to which the client is connected to.
  • WLAN— Displays the WLAN associated with the client.
  • State— Displays the client authentication.
  • Protocol— Displays the protocol used.

To view the client related general details, click the Client MAC Address parameter in the Clients page. The Client > Detail page displays IPv6 addresses of the client under the General tab.


Verifying IPv6 Address Learning Configuration

This example displays the output of the show ipv6 dhcp pool command. This command displays the IPv6 service configuration on the switch. The vlan 21 configured pool detail displays 6 clients that are currently using addresses from the pool.

Procedure

Command or Action Purpose

show ipv6 dhcp pool

Example:

Switchshow ipv6 dhcp pool 
DHCPv6 pool: vlan21
Address allocation prefix: 2001:DB8:0:1:FFFF:1234::/64 valid 86400 preferred 86400 (6 in use, 0 conflicts)
DNS server: 2001:100:0:1::1
Domain name: example.com
Active clients: 6

Displays the IPv6 service configuration on the switch.

Additional References

Related Documents

Related Topic Document Title
IPv6 command reference IPv6 Command Reference (Cisco WLC 5700 Series)IPv6 Command Reference (Catalyst 3650 Switches)
IP command reference IP Command Reference (Cisco WLC 5700 Series)IP Command Reference (Catalyst 3650 Switches)

Error Message Decoder

Description Link

To help you research and resolve system error messages in this release, use the Error Message Decoder tool.

https://www.cisco.com/cgi-bin/Support/Errordecoder/index.cgi

MIBs

MIB MIBs Link
All supported MIBs for this release.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

Technical Assistance

Description Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/support

Feature Information for IPv6 Client Address Learning

This table lists the features in this module and provides links to specific configuration information:

Feature

Release

Modification

IPv6 Client Address Learning Functionality

Cisco IOS XE 3.2SECisco IOS XE 3.3SECisco IOS XE 3.3SE

This feature was introduced.