Step 1

Choose the Basic Mode or Advanced Mode and click Go To Account Creation Page.

Step 2

Enter the username and password. Reenter the password to confirm.

Step 3

Click Create and Launch Wizard.

Step 4

Enter the device name and domain name.

Step 5

Select the appropriate time zone from the Time Zone drop-down list.

Step 6

Select the appropriate date and time mode from the Date and Time drop-down list.

Step 7

Click LAN Settings.

Step 1

Choose the Web DHCP Pool/DHCP Pool name or the Create and Associate Access VLAN option.

1. If you choose the Web DHCP Pool, specify the following:

   Pool Name—Enter the DHCP Pool Name. Network—Enter network address and the subnet mask.

2. If you choose the Create and Associate Access VLAN option, specify the following:

   Access VLAN—Enter the Access VLAN identification number. The range is from 1 to 4094. Network—Enter the IP address of the VLAN. Management Interfaces—Select the interface and move to the selected list box using the right and left arrows. You can also double click or drag and drop to move the interface to the selected list box.

Step 2

Click Primary WAN Settings.

Step 1

Select the primary WAN type. You con configure Serial, 3G/4G, Ethernet, or Broadband (xDSL) as primary WAN depending on the WAN types supported by the router.

Step 2

Select the interface from the drop-down list.

Step 3

Check the Get DNS Server info directly from ISP check box to get the DNS server information directly from the service provider. You can also manually enter the Primary DNS and Secondary DNS.

Step 4

Check the Get IP automatically from ISP check box to get the IP address information directly from the service provider. You can also manually enter the IP address and subnet mask.

Step 5

Check the Enable NAT check box to enable NAT. It is recommended to enable NAT.

Step 6

Check the Enable PPPOE check box to enable PPPoE. If you have enabled PPPoE, select the required authentication mode. The options are: PAP and CHAP.

Step 7

Enter the user name and password provided by the service provider.

Step 8

Click Security / APP Visibility WAN Settings.

Step 1

Select the secondary WAN type. You con configure Serial, 3G/4G, Ethernet, or Broadband (xDSL) as a secondary WAN depending on the WAN types supported by the router.

Step 2

Select the interface from the drop-down list.

Step 3

Check the Get DNS Server info directly from ISP check box to get the DNS server information directly from the service provider. You can also manually enter the Primary DNS and Secondary DNS.

Step 4

Check the Get IP automatically from ISP check box to get the IP address information directly from the service provider. You can also manually enter the IP address and subnet mask.

Step 5

Check the Enable NAT check box to enable NAT. It is recommended to enable NAT.

Step 6

Check the Enable PPPOE check box to enable PPPoE. If you have enabled PPPoE, select the required authentication mode. The options are PAP and CHAP .

Step 7

Enter the user name and password provided by the service provider.

Step 8

Click Security / APP Visibility WAN Settings.

Step 1

Check the Enable Cisco Recommended Security Settings check box to ensure that all passwords are not shown in plain text. The passwords are encrypted.

Step 2

Click Day 0 Config Summary.

Step 3

To preview the configuration, click CLI Preview to preview the configuration.

Step 4

Click Finish to complete the Day Zero setup.

Step 1

Configure the HTTP server. By default, the HTTP server configuration should be present on the device. Ensure the configuration by checking if the ip http server and ip http secure-server commands are present in the running configuration.

Device #configure terminal
Device (config)#ip http server
Device (config)#ip http secure-server

Step 2

Set up the authentication options to log into Web UI. You can use one of these methods to authenticate:

1. You can authenicate using local database. To use a local database for Web UI authentication, ensure to have the ip http authentication local command in the running configuration. This command is preconfigured on the device. If the command is not present, configure the device as shown in this example:

   Device #configure terminal 
   Device (config)#ip http authentication local

   Note	You need a user with privilege 15 to access the configuration screens on Web UI. If the privilege is less than 15, you can access only the Dashboard and Monitoring screens on Web UI.

   To create a user account, use the username <username> privilege <privilege> password 0 <passwordtext>

   Device #configure terminal
   Device (config)# username <username> privilege <privilege> password 0 <passwordtext>

2. Authenticate using AAA options. To use AAA authentication for Web UI, ensure to configure ‘ip http authentication aaa’ on the device. Also, ensure that the required AAA server configuration is present on the device.

   Device #configure terminal
   Device (config)#ip http authentication local
    

Step 3

Launch the browser. In the address bar, type the IP address of the device. For a secure connection, type https://ip-address.

Step 4

Enter the default username (cisco) and password provided with the device

Step 5

Click Log In.