فترات انتهاء المهلة ل PPP لكل مستخدم
المحتويات
المقدمة
يشرح هذا التلميح التقني كيفية تنفيذ حالات انتهاء المهلة الزمنية لكل مستخدم على خوادم الوصول من Cisco. لكي تعمل حالات انتهاء المهلة الزمنية لكل مستخدم بشكل صحيح، يجب عليك تشغيل الإصدار 11.3(8)T من Cisco IOS أو الأحدث. إذا قمت بتشغيل إصدار سابق من Cisco IOS، فقد تعمل وحدات التوقيت فقط في تكوينات أساسية معينة، مثل غير متزامن فقط بدون ملفات تعريف ظاهرية.
يغطي هذا المستند تكوين خادم الوصول إلى الشبكة (NAS) وخادم المصادقة والتفويض والمحاسبة (AAA). كما يوفر إخراج الأمر show وdebug حتى يمكنك تأكيد ما إذا كانت أجهزتك تعمل بشكل صحيح، وحتى يمكنك تصحيح أخطاء أي مشاكل.
المتطلبات الأساسية
المتطلبات
لا توجد متطلبات خاصة لهذا المستند.
المكونات المستخدمة
تستند المعلومات الواردة في هذا المستند إلى إصدارات البرامج والمكونات المادية التالية:
-
IOS الإصدار 11.3(8)T من Cisco أو إصدار أحدث
تم إنشاء المعلومات الواردة في هذا المستند من الأجهزة الموجودة في بيئة معملية خاصة. بدأت جميع الأجهزة المُستخدمة في هذا المستند بتكوين ممسوح (افتراضي). إذا كانت شبكتك مباشرة، فتأكد من فهمك للتأثير المحتمل لأي أمر.
الاصطلاحات
للحصول على مزيد من المعلومات حول اصطلاحات المستندات، ارجع إلى اصطلاحات تلميحات Cisco التقنية.
التفاصيل الفنية
قبل مناقشة الفترات الزمنية لكل مستخدم، والتي تتضمن متغيرات أخرى مثل تكوين المصادقة والتفويض والمحاسبة (AAA) وخوادم RADIUS/TACACS+، سندرس كيفية تكوين خادم وصول لحالات انتهاء المهلة المحددة، وهي فترات انتهاء المهلة التي يتم تطبيقها على أساس شامل ويتم تطبيقها على كل شخص يدخل في النظام.
أمر Cisco IOS هو المتصل وضع الخمول-المهلة والمهلة المطلقة. كلا هذين هما أوامر تكوين الواجهة. وسنناقش أيضا الأمر الثالث، مهلة بروتوكول الاتصال من نقطة إلى نقطة (PPP) في وضع الخمول، والذي يتم إستخدامه على واجهات vAccess.
مهلة وضع الاتصال في وضع الخمول <x>
يمكن تكوين هذا الأمر على أي واجهة قادرة على الطلب ويتحكم في المدة التي يمكن فيها وضع الاتصال في وضع الخمول (بالثواني) قبل إنهائه. فيما يلي أربع نقاط يجب عليك ملاحظتها حول هذا الأمر:
-
يمكن تطبيق هذا الأمر فقط على الواجهات القادرة على الاتصال. بشكل افتراضي، تكون جميع واجهات ISDN (BRI و PRI) قادرة على الاتصال، لذلك فإن إضافة هذا الأمر ليست مشكلة. الواجهات غير المتزامنة (بما في ذلك واجهات المجموعة غير المتزامنة) ليست قادرة على الاتصال بشكل افتراضي، يجب أن تقوم بذلك من خلال إدخال الأمر المتصل داخل النطاق. يمكنك تكوين المتصل الخامل-المهلة فقط بعد إدخال الأمر المتصل داخل النطاق على الواجهة غير المتزامنة. ملاحظة
ملاحظة: لا يدعم قالب vtemplate (وبالتالي واجهات vaccess) الاتصال (من نقطة إلى نقطة فقط) وبالتالي لا يمكنه إستخدام هذا الأمر.
-
على واجهة قادرة على الاتصال (أي بروتوكول ISDN أو غير متزامن مع المتصل داخل النطاق)، يكون الإعداد الافتراضي هو المتصل خامل-timeout 120 (ثوان). وعادة ما يكون هذا الطراز قصيرا للغاية في بيئة مزود خدمة الإنترنت (ISP)، لذا يجب عليك زيادة هذا الأمر دائما تقريبا.
-
يتم فقط إعادة تعيين مهلة خاملة للمطالب بشكل افتراضي على حركة المرور الصادرة (حركة المرور تجاه المستخدم) التي تطابق قائمة المتصل (أي أنها تعتبر مثيرة للاهتمام). من الممكن إعادة ضبطه لحركة المرور المثيرة للاهتمام الواردة أيضا من خلال إضافة أي الكلمة الأساسية في نهاية الأمر (أي، المتصل idle-timeout 600 إما).
-
يتم تحديد حركة المرور التي تعتبر "مثيرة للاهتمام" بواسطة الأمر dialer-list <n>، حيث يتطابق <n>مع الرقم في بيان أوامر dialer-group <n>.
مهلة مطلقة <x> <y>
يمكن تكوين هذا الأمر على أي واجهة شبكة WAN، بما في ذلك واجهات ISDN، وواجهات المتصل، وواجهات vtemplate. وهو يتحكم في المدة التي يمكن خلالها تشغيل الاتصال قبل إنهائه. لاحظ أن الصياغة هي <x> <y> حيث يكون <x> في دقائق و<y> في ثوان.
وضع الخمول لانتهاء مهلة بروتوكول الاتصال من نقطة إلى نقطة (PPP) <x>
يمكن تكوين هذا الأمر فقط على واجهات vtemplate (وهو حتى مخفي في المحلل)، ويتحكم في المدة التي يمكن أن يكون فيها الاتصال خاملا (بالثواني) قبل إنهائه. وعمله مشابه جدا لوظيفة الأمر dialer idle-timeout على واجهات المتصل، وفترة تعطيل بروتوكول الاتصال (PPP) فقط هي لواجهات vtemplate/vaccess. ولأنه يتم إستخدامه بشكل خاص على واجهات vtemplate/vaccess، يعتبر هذا الأمر مناسبا لتكوينات ملف التعريف الظاهري (حيث يتم إنشاء واجهة vaccess دائما للمستخدم) والعبارات الرئيسية لشبكة الطلب الهاتفي الخاصة الظاهرية (VPDN) (حيث يتم إنهاء الواجهات المتوقعة دائما على واجهة vaccess). على عكس الأمر dialer idle-timeout، لا يوجد مفهوم لحركة المرور المثيرة للاهتمام، وبالتالي ستقوم جميع حركة مرور المستخدم بإعادة ضبط المؤقت الخامل. لا تقوم حركة مرور غير المستخدم مثل رسائل keepalive لبروتوكول التحكم في الارتباط (LCP) وحزم تفاوض بروتوكول التحكم في الشبكة (NCP) بإعادة ضبط المؤقت.
التكوين
في هذا القسم، تُقدّم لك معلومات تكوين الميزات الموضحة في هذا المستند.
ملاحظة: للعثور على معلومات إضافية حول الأوامر المستخدمة في هذا المستند، أستخدم أداة بحث الأوامر (للعملاء المسجلين فقط).
يستخدم هذا المستند التكوينات التالية:
- التكوين الأساسي (لم يتم تمكين ملفات التعريف الظاهرية)
- فترات الانتظار العالمية
- فترات انتهاء المهلة لكل مستخدم - تكوين خادم AAA
- فترات الانتظار لكل مستخدم - تكوين NAS
التكوين الأساسي (لم يتم تمكين ملفات التعريف الظاهرية)
لأغراض التعلم، سنفترض تكوين أساسي مثل الموجود أدناه. لم يتم تشغيل ميزة ملفات التعريف الظاهرية.
| التكوين الأساسي |
|---|
! version 11.3 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname access-3 ! aaa new-model aaa authentication login default tacacs+ local aaa authentication login console none aaa authentication login use-radius local radius aaa authentication enable default enable aaa authentication ppp default if-needed local tacacs+ aaa authentication ppp use-radius if-needed local radius aaa authentication arap default local aaa authorization exec default tacacs+ local aaa authorization exec console none aaa authorization exec use-radius local radius if-authenticated aaa authorization network default local tacacs+ if-authenticated aaa authorization network use-radius local radius if-authenticated aaa accounting exec default stop-only tacacs+ aaa accounting network default stop-only tacacs+ aaa accounting system default start-stop tacacs+ enable secret 5 $1$oMKx$kPcop1zxkpxa8fkxXBWp21 ! modem call-record terse modem buffer-size 250 no ip finger ! isdn switch-type primary-5ess clock timezone PST -8 clock summer-time PDT recurring ! controller T1 0 framing esf clock source line primary linecode b8zs pri-group timeslots 1-24 ! interface Loopback0 ip address 10.1.1.1 255.255.255.0 no ip directed-broadcast ! interface Ethernet0 ip address 172.16.1.1 255.255.255.0 no ip directed-broadcast ! interface Virtual-Template1 ip unnumbered Loopback0 no ip directed-broadcast no keepalive peer default ip address pool default ppp authentication chap pap use-radius ppp multilink ! interface Serial0:23 ip unnumbered Loopback0 no ip directed-broadcast encapsulation ppp no logging event link-status no keepalive dialer-group 1 autodetect encapsulation ppp v120 isdn switch-type primary-5ess isdn incoming-voice modem peer default ip address pool default no fair-queue no cdp enable ppp max-bad-auth 3 ppp authentication chap pap use-radius ppp multilink ! ! interface Group-Async1 ip unnumbered Loopback0 no ip directed-broadcast encapsulation ppp no logging event link-status async mode interactive peer default ip address pool default no fair-queue no cdp enable ppp max-bad-auth 3 ppp authentication chap pap use-radius ppp multilink group-range 1 96 hold-queue 10 in ! ip local pool default 10.1.1.2 10.1.1.200 ip classless ip route 0.0.0.0 0.0.0.0 172.16.1.254 ! no logging console dialer-list 1 protocol ip permit tacacs-server host 172.16.1.201 tacacs-server key cisco radius-server host 172.16.1.202 auth-port 1645 acct-port 1646 key cisco ! line con 0 exec-timeout 0 0 authorization exec console login authentication console transport input none line 1 96 autoselect during-login autoselect ppp modem Dialin escape-character BREAK authorization exec use-radius login authentication use-radius line aux 0 line vty 0 4 exec-timeout 60 0 ! end |
فترات الانتظار العالمية
على سبيل المثال التالي، سنفرض مهلة خاملة تبلغ 30 دقيقة (1800 ثانية) وثلاث ساعات (180 دقيقة) كمهلة مطلقة للمستخدمين. سيكون تغيير تكوين دلتا الذي سيؤدي إلى تمكين حالات انتهاء المهلة الزمنية لبروتوكول الاتصال من نقطة إلى نقطة (PPP) العالمية كما يلي:
interface Serial0:23 dialer idle-timeout 1800 timeout absolute 180 ! ! interface Group=Async1 dialer in-band dialer idle-timeout 1800 dialer-group 1 timeout absolute 180
إذا لم يكن لديك قائمة المتصل رقم 1، فستحتاج إلى تعريف واحدة. وسيكون أبسط هذه الشروط هو تصريح بروتوكول الإنترنت (IP) الخاص ببروتوكول قائمة الاتصال 1.
إذا كنت تستخدم ملفات التعريف الظاهرية، فيمكن أن يكون التكوين الخاص بك أكثر سهولة لأنه يمكنك وضع المهلة على واجهة القالب الظاهري، كما هو موضح أدناه:
interface Virtual-Template1 ppp timeout idle 1800 timeout absolute 180
فترات انتهاء المهلة لكل مستخدم - تكوين خادم AAA
الآن وقد عملنا على فترات زمنية عالمية، سوف نوسع هذه المعرفة إلى فترات زمنية لكل مستخدم. سوف تظهر قيم المؤقت لكل مستخدم الخاص بك أثناء تفويض الشبكة، لذلك يجب أن يكون لديك أمر تفويض شبكة AAA مكون على أي طريقة تستخدمها، والتي هي RADIUS أو TACACS+. لاحظ أيضا أن وحدات التوقيت لكل مستخدم ستتجاوز دائما أي قيم عمومية تم تكوينها مسبقا على NAS. الطريقة التي تعمل بها وحدات التوقيت لكل مستخدم هي أنه عندما يستقبل خادم الوصول سمات المهلة أثناء مرحلة تفويض الشبكة، فإنه سيترجم هذه السمات إلى مجموعة من أوامر التكوين التي سيتم إدخالها في الواجهة التي سيتم توصيل المستخدم بها. تكون أوامر التكوين التالية التي يتم إدخالها في الواجهة بواسطة عملية في الخلفية مؤقتة، ويتم إزالتها عند قطع اتصال المستخدم.
توجد أدناه عدة نماذج لملفات تعريف المستخدمين على الخادم:
ملفات تعريف RADIUS
timeout-absolute-ppp Password = "cisco"
Service-Type = Framed,
Framed-Protocol = PPP,
Framed-IP-Address = 255.255.255.254,
Session-Timeout = 600
timeout-idle-ppp Password = "cisco"
Service-Type = Framed,
Framed-Protocol = PPP
Framed-IP-Address = 255.255.255.254,
Idle-Timeout = 300
timeout-both-ppp Password = "cisco"
Service-Type = Framed,
Framed-Protocol = PPP,
Framed-IP-Address = 255.255.255.254,
Session-Timeout = 600,
Idle-Timeout = 300
ملاحظة: قد تختلف الصياغة الخاصة بك بناء على كيفية إعداد القاموس.
ملفات تعريف TACACS+
user = timeout-absolute-ppp {
chap = cleartext cisco
service = ppp protocol = lcp {
timeout = 10
}
service = ppp protocol = ip {
addr-pool = "default"
}
}
user = timeout-idle-ppp {
chap = cleartext cisco
service = ppp protocol = lcp {
idletime = 5
}
service = ppp protocol = ip {
addr-pool = "default"
}
}
user = timeout-both-ppp {
chap = cleartext cisco
service = ppp protocol = lcp {
timeout = 10
idletime = 5
}
service = ppp protocol = multilink { }
service = ppp protocol = ip {
addr-pool = "default"
}
}
فترات الانتظار لكل مستخدم - تكوين NAS
إذا كنت تقوم بتنفيذ غير متزامن (لا يوجد ISDN) فقط ولا تستخدم ملفات التعريف الظاهرية، طالما أن لديك متصل داخل النطاق مكون على واجهات غير متزامنة (أو مجموعة غير متزامنة)، فيجب أن تعمل وحدات التوقيت لكل مستخدم. ستقوم عملية الخلفية بإدراج وحدات التوقيت على الواجهة غير المتزامنة، باستخدام الأوامر المطلقة وخامل مهلة المتصل بالقيم التي تم تمريرها من RADIUS/TACACS+، وإخراجها عند قطع اتصال المستخدم.
إذا كنت تقوم بتنفيذ غير متزامن (لا يوجد ISDN) فقط، وتستخدم ملفات التعريف الظاهرية، فأنت لا تحتاج إلى متصل داخل النطاق تم تكوينه على الواجهة async (أو group-async). يجب أن تعمل فقط. ستقوم عملية الخلفية بإدراج وحدات التوقيت على واجهة vaccess، باستخدام الأوامر المطلقة وتعطيل PPP الخاملة مع القيم التي تم تمريرها من RADIUS/TACACS+، وإخراجها عند قطع اتصال المستخدم.
إذا كان لديك مستخدمو ISDN وعليك إجراء مؤقتات لكل مستخدم، فقد تحتاج إلى إستخدام ملفات التعريف الظاهرية. السبب هو أن عملية الخلفية التي ناقشناها مسبقا لا تعمل لواجهات ISDN؛ أي لا يمكنك تكوين القناة B التي يتم توصيل المستخدم بها. الشيء الوحيد الذي يمكنك تكوينه هو القناة D التي تؤثر على الجميع. ومع ذلك، إذا قام المستخدم بالتفاوض على إرتباط متعدد على جلسة عمل، سيقوم خادم الوصول تلقائيا بإنشاء واجهة وصول ظاهري تعمل كواجهة حزمة للمستخدم. تعمل عملية الخلفية على واجهات الوصول الظاهري، ولكنها لا تعمل على إستدعاء ISDN غير متعدد الارتباطات حيث لا توجد واجهة الوصول الظاهري. لذلك، إذا كان لديك مستخدمو قناة B مفردة لا يتفاوضون على الارتباطات المتعددة وتريد تثبيت فترات المهلة لكل مستخدم لهم، فيجب تمكين ملفات التعريف الظاهرية. يؤدي تمكين ملفات التعريف الظاهرية إلى فرض إنشاء واجهة VACCESS لجميع المستخدمين (وليس فقط المستخدمين متعددي الارتباطات) ويمكن للعملية الأساسية إدراج مهلة PPP في وضع الخمول وأوامر المهلة المطلقة بنجاح. إذا أخترت عدم تمكين ملفات التعريف الظاهرية، سيتمكن المستخدمون غير المتزامنين ومستخدمو ISDN متعدد الارتباطات من تطبيق فترات انتهاء المهلة لكل مستخدم عليهم. ولكن، لا يمكن لمستخدمي ISDN غير المشتركين في إرتباط متعدد أن يتم تطبيق فترات انتهاء المهلة لكل مستخدم عليهم. سيتم تطبيق حالات انتهاء المهلة العمومية التي تم تكوينها بشكل ثابت على الواجهة (إن وجدت) فقط. إذا حاولت تطبيق حالات انتهاء المهلة لكل مستخدم على مستخدم ISDN غير متعدد الارتباطات ولم يتم تشغيل ملفات التعريف الظاهرية، فسيفشل اتصال المستخدم في التخويل لأن خادم الوصول لم يتمكن من معالجة سمات المهلة الإلزامية لكل مستخدم.
وبالإضافة إلى ذلك، تمت إضافة ميزة إلى برنامج Cisco IOS 11.3(8.1)T والإصدارات الأحدث التي تسمح بتطبيق حالات انتهاء المهلة لكل مستخدم على مستخدمي ISDN غير المرتبطين. يتجاوز بشكل أساسي وضع تكوين عملية الخلفية الذي يتم إستخدامه عادة ويضبط أجهزة التوقيت مباشرة على القناة B دون إستخدام واجهة سطر الأوامر.
لتلخيص هذا الإعداد المعقد، إليك قاعدتان يمكنك إتباعهما:
-
إذا لم تكن تستخدم ملفات التعريف الظاهرية، فقم بتكوين المتصل داخل النطاق على الواجهات غير المتزامنة وقم بتشغيل Cisco IOS 11.3(8.1)T أو الإصدارات الأحدث. إذا كنت تقوم بتشغيل Cisco IOS 11.3(8)T، فاحذر من أنه لا يمكن لمستخدمي ISDN غير المشتركين في إرتباط متعدد أن يتم تطبيق فترات انتهاء المهلة لكل مستخدم عليهم، وإلا فسيفشلون في الاتصال.
-
إذا كنت تستخدم ملفات التعريف الظاهرية، فإن برنامج Cisco IOS 11.3(8)T أو إصدار أحدث سيعمل بشكل جيد.
التحقق من الصحة
لا يوجد حاليًا إجراء للتحقق من صحة هذا التكوين.
استكشاف الأخطاء وإصلاحها
يوفر هذا القسم معلومات يمكنك استخدامها لاستكشاف أخطاء التكوين وإصلاحها. ولأغراض تصحيح الأخطاء، يتم تضمين ستة أمثلة لمخرجات المكالمات. للانتقال مباشرة إلى قسم معين، حدد أحد الروابط أدناه:
يتم دعم بعض أوامر العرض بواسطة أداة مترجم الإخراج (العملاء المسجلون فقط)، والتي تتيح لك عرض تحليل إخراج أمر العرض.
ملاحظة: قبل إصدار أوامر تصحيح الأخطاء، راجع المعلومات المهمة في أوامر تصحيح الأخطاء.
- الاتصال غير المتزامن بملفات التعريف الظاهرية - لا يؤدي الاتصال إلى وضع الخمول
- الاتصال غير المتزامن بملفات التعريف الظاهرية - خرج الاتصال
- مكالمة غير متزامنة بدون ملفات التعريف الظاهرية
- إستدعاء ISDN أحادي القناة متعدد الارتباطات بدون ملفات التعريف الظاهرية
- إستدعاء ISDN أحادي القناة غير متعدد الارتباطات بدون ملفات التعريف الظاهرية
- إستدعاء ISDN أحادي القناة غير متعدد الارتباطات مع ملفات التعريف الظاهرية
ملاحظة: لعرض نفس الأوامر والمخرجات التي يتم تقديمها أدناه، يجب أن تكون قد قمت بتشغيل Cisco IOS، الإصدار 11.3AA أو الإصدار 12.0T.
الاتصال غير المتزامن بملفات التعريف الظاهرية - لا يؤدي الاتصال إلى وضع الخمول
فيما يلي مكالمة غير متزامنة مع ملفات التعريف الظاهرية. يقوم ملف التعريف بتثبيت مهلة مطلقة مدتها 90 ثانية ومهلة خاملة مدتها 60 ثانية. في هذا المثال، لن ندع الاتصال يخمد. راجع التعليقات في المخرجات أدناه للحصول على مزيد من التفاصيل. يتم إبراز التعليقات وفي نص مائل.
!--- ISDN setup message comes in.
*Mar 4 19:21:47.772: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x09
*Mar 4 19:21:47.772: Bearer Capability i = 0x9090A2
*Mar 4 19:21:47.772: Channel ID i = 0xA98393
*Mar 4 19:21:47.772: Called Party Number i = 0xC1, '4085703932'
*Mar 4 19:21:47.776: ISDN Se0:23: TX -> CALL_PROC pd = 8 callref = 0x8009
*Mar 4 19:21:47.776: Channel ID i = 0xA98393
*Mar 4 19:21:47.776: ISDN Se0:23: TX -> ALERTING pd = 8 callref = 0x8009
!--- Modem is allocated.
*Mar 4 19:21:47.776: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3D, ces=0x1
bchan=0x12, event=0x1, cause=0x0
*Mar 4 19:21:47.776: VDEV_ALLOCATE: slot 1 and port 28 is allocated.
*Mar 4 19:21:47.776: EVENT_FROM_ISDN:(003D): DEV_INCALL at slot 1 and port 28
*Mar 4 19:21:47.776: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 28
*Mar 4 19:21:47.776: Mica Modem(1/28): Configure(0x1 = 0x0)
*Mar 4 19:21:47.776: Mica Modem(1/28): Configure(0x23 = 0x0)
*Mar 4 19:21:47.776: Mica Modem(1/28): Call Setup
*Mar 4 19:21:47.932: Mica Modem(1/28): State Transition to Call Setup
!--- Modem goes offhook.
*Mar 4 19:21:47.932: Mica Modem(1/28): Went offhook
*Mar 4 19:21:47.932: CSM_PROC_IC1_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 28
*Mar 4 19:21:47.932: ISDN Se0:23: TX -> CONNECT pd = 8 callref = 0x8009
*Mar 4 19:21:47.996: ISDN Se0:23: RX <- CONNECT_ACK pd = 8 callref = 0x09
!--- DS0 is cut-through.
*Mar 4 19:21:47.996: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3D, ces=0x1
bchan=0x12, event=0x4, cause=0x0
*Mar 4 19:21:47.996: EVENT_FROM_ISDN:(003D): DEV_CONNECTED at slot 1 and port 28
*Mar 4 19:21:47.996: CSM_PROC_IC4_WAIT_FOR_CARRIER: CSM_EVENT_ISDN_CONNECTED
at slot 1, port 28
!--- Modem training starts.
*Mar 4 19:21:47.996: Mica Modem(1/28): Link Initiate
*Mar 4 19:21:49.140: Mica Modem(1/28): State Transition to Connect
*Mar 4 19:21:54.276: Mica Modem(1/28): State Transition to Link
*Mar 4 19:22:05.828: Mica Modem(1/28): State Transition to Trainup
*Mar 4 19:22:09.028: Mica Modem(1/28): State Transition to EC Negotiating
*Mar 4 19:22:09.568: Mica Modem(1/28): State Transition to Steady State
!--- Modem training completes.
*Mar 4 19:22:10.128: AAA: parse NAME=tty53 idb TYPE=10 tty=53
*Mar 4 19:22:10.128: AAA: NAME=tty53 flags=0x11 TYPE=4 shelf=0 slot=0 adapter=0 port=53
channel=0
*Mar 4 19:22:10.128: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:22:10.128: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0 adapter=0
port=0 channel=18
!--- PPP begins negotiation.
*Mar 4 19:22:11.332: As53 LCP: Lower layer not up, Fast Starting
*Mar 4 19:22:11.332: As53 PPP: Treating connection as a dedicated line
*Mar 4 19:22:11.332: As53 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
!--- LCP negotiation completes, authentication begins.
*Mar 4 19:22:13.556: As53 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:22:13.556: As53 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar 4 19:22:16.016: As53 AUTH: Started process 0 pid 45
*Mar 4 19:22:16.016: As53 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:22:16.208: As53 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:22:16.208: As53 CHAP: O CHALLENGE id 2 len 26 from "STACK"
!--- CHAP response received from client.
*Mar 4 19:22:16.304: As53 CHAP: I RESPONSE id 2 len 30 from "timeout"
*Mar 4 19:22:16.304: AAA: parse NAME=Async53 idb TYPE=10 tty=53
*Mar 4 19:22:16.304: AAA: NAME=Async53 flags=0x11 TYPE=4 shelf=0 slot=0
adapter=0 port=53 channel=0
*Mar 4 19:22:16.304: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:22:16.304: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
!--- Send RADIUS query.
*Mar 4 19:22:16.304: RADIUS: ustruct sharecount=1
*Mar 4 19:22:16.304: RADIUS: Initial Transmit Async53 id 0 172.16.24.117:1645,
Access-Request, len 92
*Mar 4 19:22:16.304: Attribute 4 6 AC101874
*Mar 4 19:22:16.304: Attribute 5 6 00000035
*Mar 4 19:22:16.304: Attribute 61 6 00000000
*Mar 4 19:22:16.304: Attribute 1 11 74696D65
*Mar 4 19:22:16.304: Attribute 30 12 34303835
*Mar 4 19:22:16.304: Attribute 3 19 0283D0F9
*Mar 4 19:22:16.308: Attribute 6 6 00000002
*Mar 4 19:22:16.308: Attribute 7 6 00000001
!--- Received RADIUS response, note attribute 27 (Session-Timeout -> absolute timeout) !--- is 0x5A (90) and attribute 28 (Idle-Timeout) is 0x3C (60).
*Mar 4 19:22:16.316: RADIUS: Received from id 0 172.16.24.117:1645,
Access-Accept, len 50
*Mar 4 19:22:16.316: Attribute 6 6 00000002
*Mar 4 19:22:16.320: Attribute 7 6 00000001
*Mar 4 19:22:16.320: Attribute 8 6 FFFFFFFE
*Mar 4 19:22:16.320: Attribute 27 6 0000005A
*Mar 4 19:22:16.320: Attribute 28 6 0000003C
!--- Start LCP authorization.
*Mar 4 19:22:16.320: As53 AAA/AUTHOR/LCP: Authorize LCP
*Mar 4 19:22:16.320: AAA/AUTHOR/LCP As53 (3506139973): Port='Async53' list=''
service=NET
*Mar 4 19:22:16.320: AAA/AUTHOR/LCP: As53 (3506139973) send AV service=ppp
*Mar 4 19:22:16.320: AAA/AUTHOR/LCP: As53 (3506139973) send AV protocol=lcp
*Mar 4 19:22:16.320: AAA/AUTHOR/LCP (3506139973) found list "default"
*Mar 4 19:22:16.320: AAA/AUTHOR/LCP: As53 (3506139973) METHOD=RADIUS
*Mar 4 19:22:16.320: AAA/AUTHOR (3506139973): Post authorization status = PASS_REPL
!--- Gleaned per-user timeouts from user profile.
*Mar 4 19:22:16.320: As53 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar 4 19:22:16.320: As53 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar 4 19:22:16.320: As53 AAA/AUTHOR/LCP: Processing AV idletime=60
!--- Translate AAA attributes to interface configuration commands. !--- Since we are using virtual-profiles, we will use the "ppp timeout idle" !--- command instead of the "dialer in-band" command. Note that 90 second absolute timeout !--- translates to the command "timeout absolute 1 30" (1 minute and 30 seconds).
*Mar 4 19:22:16.320: AAA/AUTHOR/LCP As53: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60
!--- PPP authentication succeeds.
*Mar 4 19:22:16.320: As53 CHAP: O SUCCESS id 2 len 4
*Mar 4 19:22:16.320: AAA/ACCT/NET/START User timeout, Port Async53, List ""
*Mar 4 19:22:16.320: AAA/ACCT/NET: Found list "default"
!--- Create new vaccess interface.
*Mar 4 19:22:16.416: VTEMPLATE: No unused vaccess, create new vaccess
*Mar 4 19:22:16.416: Vi1 VTEMPLATE: Set default settings with no ip address, encap ppp
*Mar 4 19:22:16.440: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar 4 19:22:16.440: Vi1 VTEMPLATE: Has a new cloneblk vtemplate, now it has vtemplate
*Mar 4 19:22:16.440: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:22:16.440: Vi1 VTEMPLATE: Clone from Virtual-Template1
interface Virtual-Access1
default ip address
no ip address
encap ppp
ip unnumbered Loopback0
ip access-group 199 in
ip helper-address 172.16.24.118
no ip directed-broadcast
ip accounting output-packets
ip nat inside
no keepalive
peer default ip address pool default
compress mppc
ppp callback accept
ppp authentication chap pap ms-chap
ppp multilink
multilink max-links 2
end
*Mar 4 19:22:16.504: Vi1 CCP: Re-Syncing history using legacy method
!--- Now add the per-user timeouts we constructed for this user.
*Mar 4 19:22:16.520: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has vtemplate/AAA
*Mar 4 19:22:16.520: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:22:16.520: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end
!--- LCP layer is finished, negotiate the appropriate NCPs.
*Mar 4 19:22:16.532: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
*Mar 4 19:22:16.536: Vi1 PPP: Treating connection as a dedicated line
*Mar 4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM Vi1 (1906691625): Port='Async53' list='' service=NET
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (1906691625) send AV service=ppp
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (1906691625) send AV protocol=ip
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM (1906691625) found list "default"
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (1906691625) METHOD=RADIUS
*Mar 4 19:22:16.536: RADIUS: Using NAS default peer
*Mar 4 19:22:16.536: RADIUS: Authorize IP address 0.0.0.0
*Mar 4 19:22:16.536: AAA/AUTHOR (1906691625): Post authorization status = PASS_REPL
*Mar 4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar 4 19:22:16.536: Vi1 AAA/AUTHOR/FSM: (0): Can we start CCP?
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM Vi1 (282953275): Port='Async53' list='' service=NET
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (282953275) send AV service=ppp
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (282953275) send AV protocol=ccp
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM (282953275) found list "default"
*Mar 4 19:22:16.536: AAA/AUTHOR/FSM: Vi1 (282953275) METHOD=RADIUS
*Mar 4 19:22:16.540: AAA/AUTHOR (282953275): Post authorization status = PASS_REPL
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: We can start CCP
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar 4 19:22:16.540: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar 4 19:22:16.656: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar 4 19:22:16.656: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar 4 19:22:16.656: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar 4 19:22:17.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to up
*Mar 4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:22:19.516: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:22:19.608: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:22:19.612: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:22:19.704: Vi1 AAA/AUTHOR/IPCP: Start. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:22:19.704: AAA/AUTHOR/IPCP Vi1 (785695075): Port='Async53' list='' service=NET
*Mar 4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) send AV service=ppp
*Mar 4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) send AV protocol=ip
*Mar 4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) send AV addr*10.1.1.3
*Mar 4 19:22:19.708: AAA/AUTHOR/IPCP (785695075) found list "default"
*Mar 4 19:22:19.708: AAA/AUTHOR/IPCP: Vi1 (785695075) METHOD=RADIUS
*Mar 4 19:22:19.708: RADIUS: Using NAS default peer
*Mar 4 19:22:19.708: RADIUS: Authorize IP address 10.1.1.3
*Mar 4 19:22:19.708: AAA/AUTHOR (785695075): Post authorization status = PASS_REPL
*Mar 4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar 4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:22:19.708: Vi1 AAA/AUTHOR/IPCP: Done. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:22:19.708: Vi1 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar 4 19:22:19.708: Vi1 AAA/PER-USER: processing author params.
!--- PPP negotiation finished, user is connected.
!--- User is connected on line 53, async interface 53 and vaccess 1. The "show caller" !--- command shows active time and idle time for this user in Cisco IOS 11.3(8.1)AA or later.
access-3#show caller
Active Idle
Line User Service Time Time
tty 53 timeout Async 00:00:20 00:00:02
As53 timeout PPP 00:00:13 00:00:02
Vi1 timeout PPP VDP 00:00:13 00:00:11
!--- The "show caller timeout" command shows the installed absolute and idle timeout as well !--- as how much time before the user is disconnected by any timeouts. Note the timeouts !--- only show up on the vaccess interface.
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
tty 53 timeout - - -
As53 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:43
!--- The "show caller user" command gives more detailed information about the user as well as !--- providing a breakdown of the active and idle time, absolute and idle timeout, !--- and time to disconnect for both idle and absolute timeout.
access-3#show caller user timeout
User: timeout, line tty 53, service Async
Active time 00:00:31, Idle time 00:00:12
Timeouts: Absolute Idle Idle
Session Exec
Limits: - - 00:10:00
Disconnect in: - - -
TTY: Line 53, running PPP on As53
Location: MICA V.90 modems
Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
Status: Ready, Active, No Exit Banner, Async Interface Active
HW PPP Support Active
Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
Line usable as async interface, ARAP Permitted
Integrated Modem
Modem State: Ready
User: timeout, line As53, service PPP
Active time 00:00:23, Idle time 00:00:12
Timeouts: Absolute Idle
Limits: - -
Disconnect in: - -
PPP: LCP Open, multilink Closed, CHAP (<- AAA)
IP: Local 10.1.1.1
Counts: 35 packets input, 820 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
22 packets output, 517 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
User: timeout, line Vi1, service PPP VDP
Active time 00:00:24, Idle time 00:00:22
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:01:05 00:00:37
PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP, CCP
Idle timer 60 secs, idle 22 secs
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 24 packets input, 542 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
19 packets output, 167 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
tty 53 timeout - - -
As53 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:35
access-3#show caller
Active Idle
Line User Service Time Time
tty 53 timeout Async 00:00:45 00:00:27
As53 timeout PPP 00:00:38 00:00:27
Vi1 timeout PPP VDP 00:00:38 00:00:36
!--- User has been idle for 36 seconds and will be disconnected in 24 seconds. Let's !--- ping the user to see what happens.
access-3#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 92/108/132 ms
!--- Now the idle timer has been reset, so we won't disconnect the user for another !--- 58 seconds.
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
tty 53 timeout - - -
As53 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:58
!--- Ping again to reset the idle timer.
access-3#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 96/98/108 ms
!--- But note, the disconnect timer did not go back to 1 minute. The reason is because the !--- absolute timer is going to start soon.
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
tty 53 timeout - - -
As53 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:24
access-3#show caller user timeout
User: timeout, line tty 53, service Async
Active time 00:01:23, Idle time 00:00:11
Timeouts: Absolute Idle Idle
Session Exec
Limits: - - 00:10:00
Disconnect in: - - -
TTY: Line 53, running PPP on As53
Location: MICA V.90 modems
Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
Status: Ready, Active, No Exit Banner, Async Interface Active
HW PPP Support Active
Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
Line usable as async interface, ARAP Permitted
Integrated Modem
Modem State: Ready
User: timeout, line As53, service PPP
Active time 00:01:15, Idle time 00:00:11
Timeouts: Absolute Idle
Limits: - -
Disconnect in: - -
PPP: LCP Open, multilink Closed, CHAP (<- AAA)
IP: Local 10.1.1.1
Counts: 45 packets input, 1161 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
32 packets output, 897 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
User: timeout, line Vi1, service PPP VDP
Active time 00:01:16, Idle time 00:00:12
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:00:13 00:00:47
PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP, CCP
Idle timer 60 secs, idle 12 secs
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 34 packets input, 883 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
39 packets output, 547 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
!--- User is disconnected.
*Mar 4 19:23:47.536: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
*Mar 4 19:23:47.536: Vi1 VTEMPLATE: Free vaccess
*Mar 4 19:23:47.540: As53 AAA/ACCT: non-ISDN xmit 50000 recv 28800 hwidb 613307E0 ttynum 53
!--- Send accounting stop record, includes disc-cause 5 (session-timeout) and
!--- disc-cause-ext 1100 (session-timeout).
*Mar 4 19:23:47.540: AAA/ACCT/NET/STOP User timeout, Port Async53:
task_id=9 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=5
disc-cause-ext=1100
pre-bytes-in=184 pre-bytes-out=330 pre-paks-in=7 pre-paks-out=11 bytes_in=950
bytes_out=567 paks_in=37
paks_out=21 pre-session-time=5 elapsed_time=91 nas-rx-speed=28800 nas-tx-speed=50000
*Mar 4 19:23:47.540: Vi1 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar 4 19:23:47.540: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
!--- Modem hangs up.
*Mar 4 19:23:47.580: Mica Modem(1/28): State Transition to Terminating
*Mar 4 19:23:47.640: Mica Modem(1/28): State Transition to Idle
*Mar 4 19:23:47.640: Mica Modem(1/28): Went onhook
*Mar 4 19:23:47.640: CSM_PROC_IC5_OC6_CONNECTED: CSM_EVENT_MODEM_ONHOOK at slot 1, port 28
*Mar 4 19:23:47.640: VDEV_DEALLOCATE: slot 1 and port 28 is deallocated
*Mar 4 19:23:47.640: ISDN Se0:23: Event: Hangup call to call id 0x3D
!--- ISDN call is terminated.
*Mar 4 19:23:47.640: ISDN Se0:23: TX -> DISCONNECT pd = 8 callref = 0x8009
*Mar 4 19:23:47.640: Cause i = 0x8090 - Normal call clearing
*Mar 4 19:23:47.688: ISDN Se0:23: RX <- RELEASE pd = 8 callref = 0x09
*Mar 4 19:23:47.696: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8009
*Mar 4 19:23:47.744: TAC+: (866083896): received acct response status = SUCCESS
!--- Per-user timeouts are taken off the vaccess interface.
*Mar 4 19:23:48.140: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar 4 19:23:48.140: Vi1 VTEMPLATE: Found a dirty vaccess clone with vtemplate/AAA
*Mar 4 19:23:48.140: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:23:48.140: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end
!--- vaccess interface is cleaned up.
*Mar 4 19:23:48.160: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:23:48.176: Vi1 VTEMPLATE: Remove cloneblk AAA with vtemplate/AAA
*Mar 4 19:23:48.180: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:23:48.180: Vi1 VTEMPLATE: Unclone to-be-freed command#15
interface Virtual-Access1
default multilink max-links 2
default ppp multilink
default ppp authentication chap pap ms-chap
default ppp callback accept
default compress mppc
default peer default ip address pool default
default keepalive
default ip nat inside
default ip accounting output-packets
default ip directed-broadcast
default ip helper-address 172.16.24.118
default ip access-group 199 in
default ip unnumbered Loopback0
default encap ppp
default ip address
end
*Mar 4 19:23:48.264: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:23:48.284: Vi1 VTEMPLATE: Remove cloneblk vtemplate with vtemplate/AAA
*Mar 4 19:23:48.284: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1
!--- Here is the call record for the user. Note the disconnect reason is Session-Timeout !--- (absolute timeout).
*Mar 4 19:23:48.300: %CALLRECORD-3-MICA_TERSE_CALL_REC: DS0 slot/contr/chan=2/0/18,
slot/port=1/28, call_id=3D, userid=timeout, ip=10.1.1.3, calling=(n/a), called=4085703932,
std=K56Flx, prot=LAP-M, comp=V.42bis both, init-rx/tx b-rate=28800/50000, finl-rx/tx
b-rate=28800/50000, rbs=0, d-pad=6 dB, retr=0, sq=3, snr=32, rx/tx chars=1274/1477, bad=4,
rx/tx ec=45/61, bad=3, time=118, finl-state=Steady, disc(radius)=Session Timeout/Session Timeout,
disc(modem)=DF03 Tx (host to line) data flushing - OK/Requested by host/DTR dropped
*Mar 4 19:23:48.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to down
*Mar 4 19:23:49.536: As53 AAA/AUTHOR/PER-USER: Event LCP_DOWN
الاتصال غير المتزامن بملفات التعريف الظاهرية - خرج الاتصال
فيما يلي مكالمة غير متزامنة مع ملفات التعريف الظاهرية. تحتوي على نفس اسم المستخدم كما هو المثال أعلاه. يقوم ملف التعريف بتثبيت مهلة مطلقة مدتها 90 ثانية ومهلة خاملة مدتها 60 ثانية. في هذا المثال، سنترك الاتصال في وضع الخمول. لا توجد تعليقات أدناه، لكن تم إبراز مخرجات هامة.
*Mar 4 19:24:38.768: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x0A
*Mar 4 19:24:38.768: Bearer Capability i = 0x9090A2
*Mar 4 19:24:38.768: Channel ID i = 0xA98393
*Mar 4 19:24:38.768: Called Party Number i = 0xC1, '4085703932'
*Mar 4 19:24:38.772: ISDN Se0:23: TX -> CALL_PROC pd = 8 callref = 0x800A
*Mar 4 19:24:38.772: Channel ID i = 0xA98393
*Mar 4 19:24:38.772: ISDN Se0:23: TX -> ALERTING pd = 8 callref = 0x800A
*Mar 4 19:24:38.772: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3E, ces=0x1
bchan=0x12, event=0x1, cause=0x0
*Mar 4 19:24:38.772: VDEV_ALLOCATE: slot 1 and port 29 is allocated.
*Mar 4 19:24:38.772: EVENT_FROM_ISDN:(003E): DEV_INCALL at slot 1 and port 29
*Mar 4 19:24:38.772: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 29
*Mar 4 19:24:38.772: Mica Modem(1/29): Configure(0x1 = 0x0)
*Mar 4 19:24:38.772: Mica Modem(1/29): Configure(0x23 = 0x0)
*Mar 4 19:24:38.772: Mica Modem(1/29): Call Setup
*Mar 4 19:24:38.908: Mica Modem(1/29): State Transition to Call Setup
*Mar 4 19:24:38.908: Mica Modem(1/29): Went offhook
*Mar 4 19:24:38.908: CSM_PROC_IC1_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 29
*Mar 4 19:24:38.912: ISDN Se0:23: TX -> CONNECT pd = 8 callref = 0x800A
*Mar 4 19:24:38.972: ISDN Se0:23: RX <- CONNECT_ACK pd = 8 callref = 0x0A
*Mar 4 19:24:38.976: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x3E, ces=0x1
bchan=0x12, event=0x4, cause=0x0
*Mar 4 19:24:38.976: EVENT_FROM_ISDN:(003E): DEV_CONNECTED at slot 1 and port 29
*Mar 4 19:24:38.976: CSM_PROC_IC4_WAIT_FOR_CARRIER: CSM_EVENT_ISDN_CONNECTED at
slot 1, port 29
*Mar 4 19:24:38.976: Mica Modem(1/29): Link Initiate
*Mar 4 19:24:40.060: Mica Modem(1/29): State Transition to Connect
*Mar 4 19:24:45.256: Mica Modem(1/29): State Transition to Link
*Mar 4 19:24:56.796: Mica Modem(1/29): State Transition to Trainup
*Mar 4 19:24:59.996: Mica Modem(1/29): State Transition to EC Negotiating
*Mar 4 19:25:00.532: Mica Modem(1/29): State Transition to Steady State
*Mar 4 19:25:01.340: AAA: parse NAME=tty54 idb TYPE=10 tty=54
*Mar 4 19:25:01.340: AAA: NAME=tty54 flags=0x11 TYPE=4 shelf=0 slot=0
adapter=0 port=54 channel=0
*Mar 4 19:25:01.340: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:25:01.340: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:25:02.544: As54 LCP: Lower layer not up, Fast Starting
*Mar 4 19:25:02.544: As54 PPP: Treating connection as a dedicated line
*Mar 4 19:25:02.544: As54 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:25:04.744: As54 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:25:04.744: As54 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar 4 19:25:06.628: As54 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:25:06.820: As54 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:25:06.820: As54 CHAP: O CHALLENGE id 2 len 26 from "STACK"
*Mar 4 19:25:06.916: As54 CHAP: I RESPONSE id 2 len 30 from "timeout"
*Mar 4 19:25:06.916: AAA: parse NAME=Async54 idb TYPE=10 tty=54
*Mar 4 19:25:06.916: AAA: NAME=Async54 flags=0x11 TYPE=4 shelf=0 slot=0
adapter=0 port=54 channel=0
*Mar 4 19:25:06.916: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:25:06.916: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:25:06.916: RADIUS: ustruct sharecount=1
*Mar 4 19:25:06.916: RADIUS: Initial Transmit Async54 id 1 172.16.24.117:1645,
Access-Request, len 92
*Mar 4 19:25:06.916: Attribute 4 6 AC101874
*Mar 4 19:25:06.916: Attribute 5 6 00000036
*Mar 4 19:25:06.916: Attribute 61 6 00000000
*Mar 4 19:25:06.916: Attribute 1 11 74696D65
*Mar 4 19:25:06.916: Attribute 30 12 34303835
*Mar 4 19:25:06.916: Attribute 3 19 024525C7
*Mar 4 19:25:06.916: Attribute 6 6 00000002
*Mar 4 19:25:06.916: Attribute 7 6 00000001
*Mar 4 19:25:06.924: RADIUS: Received from id 1 172.16.24.117:1645,
Access-Accept, len 50
*Mar 4 19:25:06.924: Attribute 6 6 00000002
*Mar 4 19:25:06.924: Attribute 7 6 00000001
*Mar 4 19:25:06.924: Attribute 8 6 FFFFFFFE
*Mar 4 19:25:06.924: Attribute 27 6 0000005A
*Mar 4 19:25:06.928: Attribute 28 6 0000003C
*Mar 4 19:25:06.928: As54 AAA/AUTHOR/LCP: Authorize LCP
*Mar 4 19:25:06.928: AAA/AUTHOR/LCP As54 (2013841092): Port='Async54' list='' service=NET
*Mar 4 19:25:06.928: AAA/AUTHOR/LCP: As54 (2013841092) send AV service=ppp
*Mar 4 19:25:06.928: AAA/AUTHOR/LCP: As54 (2013841092) send AV protocol=lcp
*Mar 4 19:25:06.928: AAA/AUTHOR/LCP (2013841092) found list "default"
*Mar 4 19:25:06.928: AAA/AUTHOR/LCP: As54 (2013841092) METHOD=RADIUS
*Mar 4 19:25:06.928: AAA/AUTHOR (2013841092): Post authorization status = PASS_REPL
*Mar 4 19:25:06.928: As54 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar 4 19:25:06.928: As54 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar 4 19:25:06.928: As54 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar 4 19:25:06.928: AAA/AUTHOR/LCP As54: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60
*Mar 4 19:25:06.928: As54 CHAP: O SUCCESS id 2 len 4
*Mar 4 19:25:06.928: AAA/ACCT/NET/START User timeout, Port Async54, List ""
*Mar 4 19:25:06.928: AAA/ACCT/NET: Found list "default"
*Mar 4 19:25:07.028: Vi1 VTEMPLATE: Reuse Vi1, recycle queue size 0
*Mar 4 19:25:07.028: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar 4 19:25:07.028: Vi1 VTEMPLATE: Has a new cloneblk vtemplate, now it has vtemplate
*Mar 4 19:25:07.028: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:25:07.028: Vi1 VTEMPLATE: Clone from Virtual-Template1
interface Virtual-Access1
default ip address
no ip address
encap ppp
ip unnumbered Loopback0
ip access-group 199 in
ip helper-address 172.16.24.118
no ip directed-broadcast
ip accounting output-packets
ip nat inside
no keepalive
peer default ip address pool default
compress mppc
ppp callback accept
ppp authentication chap pap ms-chap
ppp multilink
multilink max-links 2
end
*Mar 4 19:25:07.092: Vi1 CCP: Re-Syncing history using legacy method
*Mar 4 19:25:07.108: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has vtemplate/AAA
*Mar 4 19:25:07.108: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:25:07.108: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end
*Mar 4 19:25:07.120: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
*Mar 4 19:25:07.124: Vi1 PPP: Treating connection as a dedicated line
*Mar 4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM Vi1 (3979277251): Port='Async54' list='' service=NET
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (3979277251) send AV service=ppp
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (3979277251) send AV protocol=ip
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM (3979277251) found list "default"
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (3979277251) METHOD=RADIUS
*Mar 4 19:25:07.124: RADIUS: Using NAS default peer
*Mar 4 19:25:07.124: RADIUS: Authorize IP address 0.0.0.0
*Mar 4 19:25:07.124: AAA/AUTHOR (3979277251): Post authorization status = PASS_REPL
*Mar 4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar 4 19:25:07.124: Vi1 AAA/AUTHOR/FSM: (0): Can we start CCP?
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM Vi1 (1524934880): Port='Async54' list='' service=NET
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (1524934880) send AV service=ppp
*Mar 4 19:25:07.124: AAA/AUTHOR/FSM: Vi1 (1524934880) send AV protocol=ccp
*Mar 4 19:25:07.128: AAA/AUTHOR/FSM (1524934880) found list "default"
*Mar 4 19:25:07.128: AAA/AUTHOR/FSM: Vi1 (1524934880) METHOD=RADIUS
*Mar 4 19:25:07.128: AAA/AUTHOR (1524934880): Post authorization status = PASS_REPL
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: We can start CCP
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar 4 19:25:07.128: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar 4 19:25:07.236: Vi1 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar 4 19:25:07.236: Vi1 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar 4 19:25:07.236: Vi1 AAA/AUTHOR/FSM: Succeeded
*Mar 4 19:25:08.120: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to up
*Mar 4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:25:10.124: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:25:10.220: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.3
*Mar 4 19:25:10.316: Vi1 AAA/AUTHOR/IPCP: Start. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:25:10.316: AAA/AUTHOR/IPCP Vi1 (2714455877): Port='Async54' list='' service=NET
*Mar 4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) send AV service=ppp
*Mar 4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) send AV protocol=ip
*Mar 4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) send AV addr*10.1.1.3
*Mar 4 19:25:10.316: AAA/AUTHOR/IPCP (2714455877) found list "default"
*Mar 4 19:25:10.316: AAA/AUTHOR/IPCP: Vi1 (2714455877) METHOD=RADIUS
*Mar 4 19:25:10.316: RADIUS: Using NAS default peer
*Mar 4 19:25:10.320: RADIUS: Authorize IP address 10.1.1.3
*Mar 4 19:25:10.320: AAA/AUTHOR (2714455877): Post authorization status = PASS_REPL
*Mar 4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar 4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:25:10.320: Vi1 AAA/AUTHOR/IPCP: Done. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:25:10.320: Vi1 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar 4 19:25:10.320: Vi1 AAA/PER-USER: processing author params.
access-3#show caller
Active Idle
Line User Service Time Time
tty 54 timeout Async 00:00:17 00:00:01
As54 timeout PPP 00:00:10 00:00:01
Vi1 timeout PPP VDP 00:00:10 00:00:08
access-3#show caller
Active Idle
Line User Service Time Time
tty 54 timeout Async 00:00:27 00:00:11
As54 timeout PPP 00:00:20 00:00:11
Vi1 timeout PPP VDP 00:00:20 00:00:18
access-3#show caller user timeout
User: timeout, line tty 54, service Async
Active time 00:00:49, Idle time 00:00:34
Timeouts: Absolute Idle Idle
Session Exec
Limits: - - 00:10:00
Disconnect in: - - -
TTY: Line 54, running PPP on As54
Location: MICA V.90 modems
Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
Status: Ready, Active, No Exit Banner, Async Interface Active
HW PPP Support Active
Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
Line usable as async interface, ARAP Permitted
Integrated Modem
Modem State: Ready
User: timeout, line As54, service PPP
Active time 00:00:43, Idle time 00:00:34
Timeouts: Absolute Idle
Limits: - -
Disconnect in: - -
PPP: LCP Open, multilink Closed, CHAP (<- AAA)
IP: Local 10.1.1.1
Counts: 35 packets input, 824 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
22 packets output, 517 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
User: timeout, line Vi1, service PPP VDP
Active time 00:00:43, Idle time 00:00:41
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:00:45 00:00:18
PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP, CCP
Idle timer 60 secs, idle 41 secs
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 24 packets input, 546 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
19 packets output, 167 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
tty 54 timeout - - -
As54 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:05
*Mar 4 19:26:10.320: Vi1 PPP: Idle timeout, dropping connection
*Mar 4 19:26:10.320: As54 AAA/ACCT: non-ISDN xmit 50000 recv 28800 hwidb 613360C8 ttynum 54
*Mar 4 19:26:10.320: AAA/ACCT/NET/STOP User timeout, Port Async54:
task_id=10 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=4
disc-cause-ext=1021 pre-bytes-in=184 pre-bytes-out=330 pre-paks-in=7 pre-paks-out=11
bytes_in=613 bytes_out=187 paks_in=27 paks_out=11 pre-session-time=4 elapsed_time=63
nas-rx-speed=28800 nas-tx-speed=50000
*Mar 4 19:26:10.320: Vi1 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar 4 19:26:10.324: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
*Mar 4 19:26:10.324: Vi1 VTEMPLATE: Free vaccess
*Mar 4 19:26:10.328: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:26:10.376: Mica Modem(1/29): State Transition to Terminating
*Mar 4 19:26:10.436: Mica Modem(1/29): State Transition to Idle
*Mar 4 19:26:10.436: Mica Modem(1/29): Went onhook
*Mar 4 19:26:10.436: CSM_PROC_IC5_OC6_CONNECTED: CSM_EVENT_MODEM_ONHOOK at slot 1,
port 29
*Mar 4 19:26:10.440: VDEV_DEALLOCATE: slot 1 and port 29 is deallocated
*Mar 4 19:26:10.440: ISDN Se0:23: Event: Hangup call to call id 0x3E
*Mar 4 19:26:10.440: ISDN Se0:23: TX -> DISCONNECT pd = 8 callref = 0x800A
*Mar 4 19:26:10.440: Cause i = 0x8090 - Normal call clearing
*Mar 4 19:26:10.488: ISDN Se0:23: RX <- RELEASE pd = 8 callref = 0x0A
*Mar 4 19:26:10.496: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x800A
*Mar 4 19:26:10.528: TAC+: (2047544826): received acct response status = SUCCESS
*Mar 4 19:26:11.180: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar 4 19:26:11.180: Vi1 VTEMPLATE: Found a dirty vaccess clone with vtemplate/AAA
*Mar 4 19:26:11.180: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:26:11.180: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end
*Mar 4 19:26:11.200: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:26:11.216: Vi1 VTEMPLATE: Remove cloneblk AAA with vtemplate/AAA
*Mar 4 19:26:11.216: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:26:11.216: Vi1 VTEMPLATE: Unclone to-be-freed command#15
interface Virtual-Access1
default multilink max-links 2
default ppp multilink
default ppp authentication chap pap ms-chap
default ppp callback accept
default compress mppc
default peer default ip address pool default
default keepalive
default ip nat inside
default ip accounting output-packets
default ip directed-broadcast
default ip helper-address 172.16.24.118
default ip access-group 199 in
default ip unnumbered Loopback0
default encap ppp
default ip address
end
*Mar 4 19:26:11.304: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:26:11.324: Vi1 VTEMPLATE: Remove cloneblk vtemplate with vtemplate/AAA
*Mar 4 19:26:11.324: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1
*Mar 4 19:26:11.324: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to down
*Mar 4 19:26:11.460: Mica Modem(1/29): State Transition to Terminating
*Mar 4 19:26:11.520: Mica Modem(1/29): State Transition to Idle
*Mar 4 19:26:12.200: %CALLRECORD-3-MICA_TERSE_CALL_REC: DS0 slot/contr/chan=2/0/18,
slot/port=1/29, call_id=3E, userid=timeout, ip=10.1.1.3, calling=(n/a), called=4085703932,
std=K56Flx, prot=LAP-M, comp=V.42bis both, init-rx/tx b-rate=28800/50000, finl-rx/tx
b-rate=28800/50000, rbs=0, d-pad=6 dB, retr=0, sq=3, snr=34, rx/tx chars=918/1138, bad=5,
rx/tx ec=35/47, bad=0, time=90, finl-state=Steady, disc(radius)=Idle Timeout/Idle Timeout,
disc(modem)=DF03 Tx (host to line) data flushing - OK/Requested by host/DTR dropped
*Mar 4 19:26:12.320: As54 AAA/AUTHOR/PER-USER: Event LCP_DOWN
مكالمة غير متزامنة بدون ملفات التعريف الظاهرية
فيما يلي مكالمة غير متزامنة بدون تمكين ملفات التعريف الظاهرية. لاحظ أنه يتم إستخدام الأمر dialer idle-timeout بدلا من الأمر ppp timeout idle نظرا لأننا لا نستخدم ملفات التعريف الظاهرية ولا توجد واجهة vaccess. كما سترى أننا نقوم بإنشاء الأمر per-user timeout، وفي الوقت نفسه، الأمر no version من الأوامر. يتم تثبيت أوامر المؤقت لكل مستخدم على الفور، بينما يتم إدراج no version من الأوامر في قائمة الانتظار إلى الواجهة لمعالجتها عند قطع اتصال المستخدم.
*Mar 4 19:30:28.420: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x06
*Mar 4 19:30:28.420: Bearer Capability i = 0x9090A2
*Mar 4 19:30:28.420: Channel ID i = 0xA98393
*Mar 4 19:30:28.420: Called Party Number i = 0xC1, '4085703932'
*Mar 4 19:30:28.420: ISDN Se0:23: TX -> CALL_PROC pd = 8 callref = 0x8006
*Mar 4 19:30:28.420: Channel ID i = 0xA98393
*Mar 4 19:30:28.424: ISDN Se0:23: TX -> ALERTING pd = 8 callref = 0x8006
*Mar 4 19:30:28.424: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x40, ces=0x1
bchan=0x12, event=0x1, cause=0x0
*Mar 4 19:30:28.424: VDEV_ALLOCATE: slot 1 and port 2 is allocated.
*Mar 4 19:30:28.424: EVENT_FROM_ISDN:(0040): DEV_INCALL at slot 1 and port 2
*Mar 4 19:30:28.424: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 2
*Mar 4 19:30:28.424: Mica Modem(1/2): Configure(0x1 = 0x0)
*Mar 4 19:30:28.424: Mica Modem(1/2): Configure(0x23 = 0x0)
*Mar 4 19:30:28.424: Mica Modem(1/2): Call Setup
*Mar 4 19:30:28.552: Mica Modem(1/2): State Transition to Call Setup
*Mar 4 19:30:28.552: Mica Modem(1/2): Went offhook
*Mar 4 19:30:28.552: CSM_PROC_IC1_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 2
*Mar 4 19:30:28.552: ISDN Se0:23: TX -> CONNECT pd = 8 callref = 0x8006
*Mar 4 19:30:28.604: ISDN Se0:23: RX <- CONNECT_ACK pd = 8 callref = 0x06
*Mar 4 19:30:28.604: EVENT_FROM_ISDN::dchan_idb=0x6122CFCC, call_id=0x40, ces=0x1
bchan=0x12, event=0x4, cause=0x0
*Mar 4 19:30:28.604: EVENT_FROM_ISDN:(0040): DEV_CONNECTED at slot 1 and port 2
*Mar 4 19:30:28.604: CSM_PROC_IC4_WAIT_FOR_CARRIER: CSM_EVENT_ISDN_CONNECTED
at slot 1, port 2
*Mar 4 19:30:28.604: Mica Modem(1/2): Link Initiate
*Mar 4 19:30:29.692: Mica Modem(1/2): State Transition to Connect
*Mar 4 19:30:34.888: Mica Modem(1/2): State Transition to Link
*Mar 4 19:30:46.408: Mica Modem(1/2): State Transition to Trainup
*Mar 4 19:30:49.612: Mica Modem(1/2): State Transition to EC Negotiating
*Mar 4 19:30:50.156: Mica Modem(1/2): State Transition to Steady State
*Mar 4 19:30:50.592: AAA: parse NAME=tty27 idb TYPE=10 tty=27
*Mar 4 19:30:50.592: AAA: NAME=tty27 flags=0x11 TYPE=4 shelf=0 slot=0
adapter=0 port=27 channel=0
*Mar 4 19:30:50.592: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:30:50.592: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:30:51.792: As27 LCP: Lower layer not up, Fast Starting
*Mar 4 19:30:51.792: As27 PPP: Treating connection as a callin
*Mar 4 19:30:51.792: As27 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:30:57.468: As27 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:30:57.468: As27 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar 4 19:30:57.564: As27 CHAP: I RESPONSE id 1 len 30 from "timeout"
*Mar 4 19:30:57.564: AAA: parse NAME=Async27 idb TYPE=10 tty=27
*Mar 4 19:30:57.564: AAA: NAME=Async27 flags=0x11 TYPE=4 shelf=0 slot=0
adapter=0 port=27 channel=0
*Mar 4 19:30:57.564: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:30:57.564: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:30:57.564: RADIUS: ustruct sharecount=1
*Mar 4 19:30:57.564: RADIUS: Initial Transmit Async27 id 3 172.16.24.117:1645,
Access-Request, len 92
*Mar 4 19:30:57.564: Attribute 4 6 AC101874
*Mar 4 19:30:57.564: Attribute 5 6 0000001B
*Mar 4 19:30:57.564: Attribute 61 6 00000000
*Mar 4 19:30:57.564: Attribute 1 11 74696D65
*Mar 4 19:30:57.564: Attribute 30 12 34303835
*Mar 4 19:30:57.564: Attribute 3 19 01E5C3F6
*Mar 4 19:30:57.564: Attribute 6 6 00000002
*Mar 4 19:30:57.564: Attribute 7 6 00000001
*Mar 4 19:30:57.572: RADIUS: Received from id 3 172.16.24.117:1645,
Access-Accept, len 50
*Mar 4 19:30:57.572: Attribute 6 6 00000002
*Mar 4 19:30:57.572: Attribute 7 6 00000001
*Mar 4 19:30:57.572: Attribute 8 6 FFFFFFFE
*Mar 4 19:30:57.572: Attribute 27 6 0000005A
*Mar 4 19:30:57.572: Attribute 28 6 0000003C
*Mar 4 19:30:57.572: As27 AAA/AUTHOR/LCP: Authorize LCP
*Mar 4 19:30:57.572: AAA/AUTHOR/LCP As27 (1969884263): Port='Async27' list=''
service=NET
*Mar 4 19:30:57.572: AAA/AUTHOR/LCP: As27 (1969884263) send AV service=ppp
*Mar 4 19:30:57.572: AAA/AUTHOR/LCP: As27 (1969884263) send AV protocol=lcp
*Mar 4 19:30:57.572: AAA/AUTHOR/LCP (1969884263) found list "default"
*Mar 4 19:30:57.572: AAA/AUTHOR/LCP: As27 (1969884263) METHOD=RADIUS
*Mar 4 19:30:57.572: AAA/AUTHOR (1969884263): Post authorization status = PASS_REPL
*Mar 4 19:30:57.572: As27 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar 4 19:30:57.572: As27 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar 4 19:30:57.572: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar 4 19:30:57.576: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:30:57.576: As27 AAA/AUTHOR: Parse 'timeout absolute 1 30'
*Mar 4 19:30:57.580: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:30:57.580: As27 AAA/AUTHOR: enqueue peruser LCP txt=interface Async27
no timeout absolute
*Mar 4 19:30:57.580: As27 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar 4 19:30:57.580: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar 4 19:30:57.584: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:30:57.584: As27 AAA/AUTHOR: Parse 'dialer idle-timeout 60'
*Mar 4 19:30:57.588: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:30:57.588: As27 AAA/AUTHOR: enqueue peruser LCP txt=interface Async27
no dialer idle-timeout
*Mar 4 19:30:57.588: As27 CHAP: O SUCCESS id 1 len 4
*Mar 4 19:30:57.588: AAA/ACCT/NET/START User timeout, Port Async27, List ""
*Mar 4 19:30:57.588: AAA/ACCT/NET: Found list "default"
*Mar 4 19:30:57.692: As27 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar 4 19:30:57.692: AAA/AUTHOR/FSM As27 (2088523207): Port='Async27' list=''
service=NET
*Mar 4 19:30:57.692: AAA/AUTHOR/FSM: As27 (2088523207) send AV service=ppp
*Mar 4 19:30:57.692: AAA/AUTHOR/FSM: As27 (2088523207) send AV protocol=ip
*Mar 4 19:30:57.692: AAA/AUTHOR/FSM (2088523207) found list "default"
*Mar 4 19:30:57.692: AAA/AUTHOR/FSM: As27 (2088523207) METHOD=RADIUS
*Mar 4 19:30:57.692: RADIUS: Using NAS default peer
*Mar 4 19:30:57.692: RADIUS: Authorize IP address 10.1.1.6
*Mar 4 19:30:57.692: AAA/AUTHOR (2088523207): Post authorization status = PASS_REPL
*Mar 4 19:30:57.692: As27 AAA/AUTHOR/FSM: We can start IPCP
*Mar 4 19:30:57.784: As27 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.6
*Mar 4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar 4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:30:57.788: As27 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.6
*Mar 4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.6
*Mar 4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar 4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:31:00.792: As27 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.6
*Mar 4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 10.1.1.6
*Mar 4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar 4 19:31:00.884: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:31:00.888: As27 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 10.1.1.6
*Mar 4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Start. Her address 10.1.1.6, we want 10.1.1.6
*Mar 4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.6
*Mar 4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:31:00.984: As27 AAA/AUTHOR/IPCP: Done. Her address 10.1.1.6, we want 10.1.1.6
*Mar 4 19:31:00.984: As27 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar 4 19:31:00.984: As27 AAA/PER-USER: processing author params.
access-3#show caller
Active Idle
Line User Service Time Time
tty 27 timeout Async 00:00:23 00:00:04
As27 timeout PPP 00:00:22 00:00:20
access-3#show caller user timeout
User: timeout, line tty 27, service Async
Active time 00:00:28, Idle time 00:00:08
Timeouts: Absolute Idle Idle
Session Exec
Limits: - - 00:10:00
Disconnect in: - - -
TTY: Line 27, running PPP on As27
Location: MICA V.90 modems
Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
Status: Ready, Active, No Exit Banner, Async Interface Active
HW PPP Support Active
Capabilities: No Flush-at-Activation, Hardware Flowcontrol In
Hardware Flowcontrol Out, Modem Callout, Modem RI is CD
Line usable as async interface, ARAP Permitted
Integrated Modem
Modem State: Ready
User: timeout, line As27, service PPP
Active time 00:00:27, Idle time 00:00:25
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:01:09 00:00:34
PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP
Dialer: Connected, inbound
Idle timer 60 secs, idle 25 secs
Type is IN-BAND ASYNC, group Async27
IP: Local 10.1.1.1, remote 10.1.1.6
Counts: 31 packets input, 1642 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
15 packets output, 347 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
tty 27 timeout - - -
As27 timeout 00:01:30 00:01:00 00:00:22
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
tty 27 timeout - - -
As27 timeout 00:01:30 00:01:00 00:00:07
access-3#
*Mar 4 19:31:53.824: Mica Modem(1/2): State Transition to Terminating
*Mar 4 19:31:53.884: Mica Modem(1/2): State Transition to Idle
*Mar 4 19:31:53.884: Mica Modem(1/2): Went onhook
*Mar 4 19:31:53.884: CSM_PROC_IC5_OC6_CONNECTED: CSM_EVENT_MODEM_ONHOOK at slot 1, port 2
*Mar 4 19:31:53.884: VDEV_DEALLOCATE: slot 1 and port 2 is deallocated
*Mar 4 19:31:53.888: ISDN Se0:23: Event: Hangup call to call id 0x40
*Mar 4 19:31:53.888: ISDN Se0:23: TX -> DISCONNECT pd = 8 callref = 0x8006
*Mar 4 19:31:53.888: Cause i = 0x8090 - Normal call clearing
*Mar 4 19:31:53.940: ISDN Se0:23: RX <- RELEASE pd = 8 callref = 0x06
*Mar 4 19:31:53.952: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8006
*Mar 4 19:31:55.792: As27 AAA/ACCT: non-ISDN xmit 50000 recv 28800 hwidb 611CEBC0 ttynum 27
*Mar 4 19:31:55.792: AAA/ACCT/NET/STOP User timeout, Port Async27:
task_id=12 timezone=PST service=ppp protocol=ip addr=10.1.1.6 disc-cause=4
disc-cause-ext=1021 pre-bytes-in=135 pre-bytes-out=176 pre-paks-in=5 pre-paks-out=6
bytes_in=1480 bytes_out=171 paks_in=25 paks_out=9 pre-session-time=6 elapsed_time=58
nas-rx-speed=28800 nas-tx-speed=50000
*Mar 4 19:31:55.792: As27 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar 4 19:31:55.792: As27 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:31:55.792: As27 AAA/AUTHOR: down_event: peruser LCP txt=interface Async27
no timeout absolute
*Mar 4 19:31:55.796: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar 4 19:31:55.800: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:31:55.800: As27 AAA/AUTHOR: Parse 'no timeout absolute'
*Mar 4 19:31:55.804: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:31:55.804: As27 AAA/AUTHOR: free peruser LCP txt=interface Async27
no timeout absolute
*Mar 4 19:31:55.804: As27 AAA/AUTHOR: down_event: peruser LCP txt=interface Async27
no dialer idle-timeout
*Mar 4 19:31:55.804: As27 AAA/AUTHOR: Parse 'interface Async27'
*Mar 4 19:31:55.808: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:31:55.808: As27 AAA/AUTHOR: Parse 'no dialer idle-timeout'
*Mar 4 19:31:55.812: As27 AAA/AUTHOR: Parse returned ok (0)
*Mar 4 19:31:55.812: As27 AAA/AUTHOR: free peruser LCP txt=interface Async27
no dialer idle-timeout
*Mar 4 19:31:56.016: TAC+: (3633056702): received acct response status = SUCCESS
*Mar 4 19:32:00.308: %CALLRECORD-3-MICA_TERSE_CALL_REC: DS0 slot/contr/chan=2/0/18,
slot/port=1/2, call_id=40, userid=timeout, ip=10.1.1.6, calling=(n/a), called=4085703932,
std=K56Flx, prot=LAP-M, comp=V.42bis both, init-rx/tx b-rate=28800/50000, finl-rx/tx
b-rate=28800/50000, rbs=0, d-pad=6 dB, retr=0, sq=3, snr=28, rx/tx chars=1727/995, bad=2,
rx/tx ec=31/36, bad=0, time=84, finl-state=Steady, disc(radius)=Idle Timeout/Idle Timeout,
disc(modem)=DF03 Tx (host to line) data flushing - OK/Requested by host/DTR dropped
إستدعاء ISDN أحادي القناة متعدد الارتباطات بدون ملفات التعريف الظاهرية
فيما يلي إستدعاء ISDN متعدد الارتباطات دون تمكين ملفات التعريف الظاهرية. ونظرا لأن مكالمة متعددة الارتباطات تقوم بإنشاء واجهة vAccess، يمكن تثبيت وحدات التوقيت بسهولة.
*Mar 4 19:41:12.208: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x08
*Mar 4 19:41:12.212: Bearer Capability i = 0x8890
*Mar 4 19:41:12.212: Channel ID i = 0xA98393
*Mar 4 19:41:12.212: Calling Party Number i = '!', 0x80, '4085551200'
*Mar 4 19:41:12.212: Called Party Number i = 0xA1, '4085703930'
*Mar 4 19:41:12.212: ISDN Se0:23: TX -> CALL_PROC pd = 8 callref = 0x8008
*Mar 4 19:41:12.212: Channel ID i = 0xA98393
*Mar 4 19:41:12.224: ISDN Se0:23: TX -> CONNECT pd = 8 callref = 0x8008
*Mar 4 19:41:12.224: Channel ID i = 0xA98393
*Mar 4 19:41:12.296: ISDN Se0:23: RX <- CONNECT_ACK pd = 8 callref = 0x08
*Mar 4 19:41:12.536: Se0:18 PPP: Treating connection as a callin
*Mar 4 19:41:12.536: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:41:14.536: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:41:14.552: Se0:18 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:41:14.552: Se0:18 CHAP: O CHALLENGE id 1 len 26 from "STACK"
*Mar 4 19:41:14.584: Se0:18 CHAP: I RESPONSE id 1 len 30 from "timeout"
*Mar 4 19:41:14.964: Se0:18 CHAP: I RESPONSE id 1 len 30 from "timeout"
*Mar 4 19:41:14.964: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:41:14.964: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:41:14.964: AAA: parse NAME= idb TYPE=-1 tty=-1
*Mar 4 19:41:14.964: RADIUS: ustruct sharecount=1
*Mar 4 19:41:14.964: RADIUS: Initial Transmit Serial0:18 id 4 172.16.24.117:1645,
Access-Request, len 104
*Mar 4 19:41:14.964: Attribute 4 6 AC101874
*Mar 4 19:41:14.964: Attribute 5 6 00004E32
*Mar 4 19:41:14.964: Attribute 61 6 00000002
*Mar 4 19:41:14.964: Attribute 1 11 74696D65
*Mar 4 19:41:14.964: Attribute 30 12 34303835
*Mar 4 19:41:14.964: Attribute 31 12 34303835
*Mar 4 19:41:14.964: Attribute 3 19 012C4E14
*Mar 4 19:41:14.964: Attribute 6 6 00000002
*Mar 4 19:41:14.964: Attribute 7 6 00000001
*Mar 4 19:41:14.972: RADIUS: Received from id 4 172.16.24.117:1645, Access-Accept, len 50
*Mar 4 19:41:14.972: Attribute 6 6 00000002
*Mar 4 19:41:14.972: Attribute 7 6 00000001
*Mar 4 19:41:14.972: Attribute 8 6 FFFFFFFE
*Mar 4 19:41:14.972: Attribute 27 6 0000005A
*Mar 4 19:41:14.972: Attribute 28 6 0000003C
*Mar 4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Authorize LCP
*Mar 4 19:41:14.976: AAA/AUTHOR/LCP Se0:18 (4039479425): Port='Serial0:18' list=''
service=NET
*Mar 4 19:41:14.976: AAA/AUTHOR/LCP: Se0:18 (4039479425) send AV service=ppp
*Mar 4 19:41:14.976: AAA/AUTHOR/LCP: Se0:18 (4039479425) send AV protocol=lcp
*Mar 4 19:41:14.976: AAA/AUTHOR/LCP (4039479425) found list "default"
*Mar 4 19:41:14.976: AAA/AUTHOR/LCP: Se0:18 (4039479425) METHOD=RADIUS
*Mar 4 19:41:14.976: AAA/AUTHOR (4039479425): Post authorization status = PASS_REPL
*Mar 4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar 4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar 4 19:41:14.976: Se0:18 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar 4 19:41:14.976: AAA/AUTHOR/LCP Se0:18: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60
*Mar 4 19:41:14.976: Se0:18 CHAP: O SUCCESS id 1 len 4
*Mar 4 19:41:14.976: AAA/ACCT/NET/START User timeout, Port Serial0:18, List ""
*Mar 4 19:41:14.976: AAA/ACCT/NET: Found list "default"
*Mar 4 19:41:14.976: AAA/AUTHOR/MLP Se0:18 (1966034416): Port='Serial0:18' list=''
service=NET
*Mar 4 19:41:14.976: AAA/AUTHOR/MLP: Se0:18 (1966034416) send AV service=ppp
*Mar 4 19:41:14.976: AAA/AUTHOR/MLP: Se0:18 (1966034416) send AV protocol=multilink
*Mar 4 19:41:14.976: AAA/AUTHOR/MLP (1966034416) found list "default"
*Mar 4 19:41:14.976: AAA/AUTHOR/MLP: Se0:18 (1966034416) METHOD=RADIUS
*Mar 4 19:41:14.976: AAA/AUTHOR (1966034416): Post authorization status = PASS_REPL
*Mar 4 19:41:14.976: Vi1 VTEMPLATE: Reuse Vi1, recycle queue size 0
*Mar 4 19:41:14.980: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar 4 19:41:14.980: Vi1 VTEMPLATE: Has a new cloneblk dialer, now it has dialer
*Mar 4 19:41:14.980: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has dialer/AAA
*Mar 4 19:41:14.980: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:41:14.980: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end
*Mar 4 19:41:14.996: Vi1 PPP: Treating connection as a callin
*Mar 4 19:41:14.996: AAA/AUTHOR/MLP Vi1: Processing AV service=ppp
*Mar 4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM Vi1 (921779905): Port='Serial0:18' list='' service=NET
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (921779905) send AV service=ppp
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (921779905) send AV protocol=ip
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM (921779905) found list "default"
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (921779905) METHOD=RADIUS
*Mar 4 19:41:15.000: RADIUS: Using NAS default peer
*Mar 4 19:41:15.000: RADIUS: Authorize IP address 0.0.0.0
*Mar 4 19:41:15.000: AAA/AUTHOR (921779905): Post authorization status = PASS_REPL
*Mar 4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar 4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: (0): Can we start CDPCP?
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM Vi1 (3065122210): Port='Serial0:18' list=''
service=NET
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (3065122210) send AV service=ppp
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (3065122210) send AV protocol=cdp
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM (3065122210) found list "default"
*Mar 4 19:41:15.000: AAA/AUTHOR/FSM: Vi1 (3065122210) METHOD=RADIUS
*Mar 4 19:41:15.000: AAA/AUTHOR (3065122210): Post authorization status = PASS_REPL
*Mar 4 19:41:15.000: Vi1 AAA/AUTHOR/FSM: We can start CDPCP
access-3#show caller
Active Idle
Line User Service Time Time
Se0:18 timeout PPP 00:00:19 00:00:00
Vi1 timeout PPP Bundle 00:00:19 00:00:20
access-3#show caller user timeout
User: timeout, line Se0:18, service PPP
Active time 00:00:25, Idle time 00:00:00
Timeouts: Absolute Idle
Limits: - -
Disconnect in: - -
PPP: LCP Open, multilink Open, CHAP (<- AAA)
Dialer: Connected to 4085551200, inbound
Type is ISDN, group Serial0:23
IP: Local 10.1.1.1
Access list (I/O) is 199/not set
Bundle: Member of timeout/timeout, last input 00:00:00
Counts: 13 packets input, 279 bytes, 0 no buffer
11 input errors, 2 CRC, 3 frame, 0 overrun
23 packets output, 431 bytes, 0 underruns
0 output errors, 0 collisions, 40 interface resets
User: timeout, line Vi1, service PPP Bundle
Active time 00:00:25, Idle time 00:00:26
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:01:04 00:00:33
PPP: LCP Open, multilink Open
Idle timer 60 secs, idle 26 secs
Dialer: Connected to 4085551200, inbound
Type is IN-BAND SYNC, group Serial0:23
IP: Local 10.1.1.1
Access list (I/O) is 199/not set
Bundle: First link of timeout/timeout, 1 link, last input 00:00:27
Counts: 0 packets input, 0 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
13 packets output, 236 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:30
access-3#
*Mar 4 19:42:14.996: Vi1 PPP: Idle timeout, dropping connection
*Mar 4 19:42:14.996: Vi1 VTEMPLATE: Free vaccess
*Mar 4 19:42:14.996: Se0:18 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:42:15.000: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:42:15.004: Se0:18 AAA/ACCT: ISDN xmit 64000 recv 64000 hwidb 612048BC
*Mar 4 19:42:15.004: AAA/ACCT/NET/STOP User timeout, Port Serial0:18:
task_id=13 timezone=PST service=ppp mlp-links-max=1 mlp-links-current=1
mlp-sess-id=0 disc-cause=18 disc-cause-ext=1046 pre-bytes-in=125 pre-bytes-out=99
pre-paks-in=4 pre-paks-out=4 bytes_in=228 bytes_out=436 paks_in=15 paks_out=26
pre-session-time=3 elapsed_time=60 nas-rx-speed=64000 nas-tx-speed=64000
*Mar 4 19:42:15.008: ISDN Se0:23: TX -> DISCONNECT pd = 8 callref = 0x8008
*Mar 4 19:42:15.008: Cause i = 0x8090 - Normal call clearing
*Mar 4 19:42:15.060: ISDN Se0:23: RX <- RELEASE pd = 8 callref = 0x08
*Mar 4 19:42:15.072: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8008
*Mar 4 19:42:15.212: TAC+: (2571416724): received acct response status = SUCCESS
*Mar 4 19:42:15.500: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar 4 19:42:15.500: Vi1 VTEMPLATE: Found a dirty vaccess clone with dialer/AAA
*Mar 4 19:42:15.500: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:42:15.500: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end
*Mar 4 19:42:15.516: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:42:15.536: Vi1 VTEMPLATE: Remove cloneblk AAA with dialer/AAA
*Mar 4 19:42:15.536: Vi1 VTEMPLATE: Remove cloneblk dialer with dialer/AAA
*Mar 4 19:42:15.536: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1
إستدعاء ISDN أحادي القناة غير متعدد الارتباطات بدون ملفات التعريف الظاهرية
فيما يلي إستدعاء ISDN أحادي القناة غير متعدد الارتباطات بدون تمكين ملفات التعريف الظاهرية. في هذا المثال، نقوم بتشغيل برنامج Cisco IOS 11.3(8.2)AA حتى يمكن تثبيت وحدات التوقيت هذه بشكل صحيح. ومع ذلك، لاحظ أنه لم يتم إنشاء أي أوامر تكوين للقيام بذلك؛ تم تعيين وحدات التوقيت داخليا في الرمز.
*Mar 4 19:43:00.404: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x0E
*Mar 4 19:43:00.404: Bearer Capability i = 0x8890
*Mar 4 19:43:00.404: Channel ID i = 0xA98393
*Mar 4 19:43:00.404: Calling Party Number i = '!', 0x80, '4085551200'
*Mar 4 19:43:00.404: Called Party Number i = 0xA1, '4085703930'
*Mar 4 19:43:00.404: ISDN Se0:23: TX -> CALL_PROC pd = 8 callref = 0x800E
*Mar 4 19:43:00.408: Channel ID i = 0xA98393
*Mar 4 19:43:00.416: ISDN Se0:23: TX -> CONNECT pd = 8 callref = 0x800E
*Mar 4 19:43:00.416: Channel ID i = 0xA98393
*Mar 4 19:43:00.488: ISDN Se0:23: RX <- CONNECT_ACK pd = 8 callref = 0x0E
*Mar 4 19:43:00.720: Se0:18 PPP: Treating connection as a callin
*Mar 4 19:43:00.720: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:43:02.744: Se0:18 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:43:02.744: Se0:18 CHAP: O CHALLENGE id 2 len 26 from "STACK"
*Mar 4 19:43:02.776: Se0:18 CHAP: I RESPONSE id 2 len 30 from "timeout"
*Mar 4 19:43:02.776: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:43:02.776: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:43:02.776: AAA: parse NAME= idb TYPE=-1 tty=-1
*Mar 4 19:43:02.780: RADIUS: ustruct sharecount=1
*Mar 4 19:43:02.780: RADIUS: Initial Transmit Serial0:18 id 5 172.16.24.117:1645,
Access-Request, len 104
*Mar 4 19:43:02.780: Attribute 4 6 AC101874
*Mar 4 19:43:02.780: Attribute 5 6 00004E32
*Mar 4 19:43:02.780: Attribute 61 6 00000002
*Mar 4 19:43:02.780: Attribute 1 11 74696D65
*Mar 4 19:43:02.780: Attribute 30 12 34303835
*Mar 4 19:43:02.780: Attribute 31 12 34303835
*Mar 4 19:43:02.780: Attribute 3 19 02AE5572
*Mar 4 19:43:02.780: Attribute 6 6 00000002
*Mar 4 19:43:02.780: Attribute 7 6 00000001
*Mar 4 19:43:02.784: RADIUS: Received from id 5 172.16.24.117:1645, Access-Accept, len 50
*Mar 4 19:43:02.784: Attribute 6 6 00000002
*Mar 4 19:43:02.784: Attribute 7 6 00000001
*Mar 4 19:43:02.784: Attribute 8 6 FFFFFFFE
*Mar 4 19:43:02.784: Attribute 27 6 0000005A
*Mar 4 19:43:02.784: Attribute 28 6 0000003C
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Authorize LCP
*Mar 4 19:43:02.788: AAA/AUTHOR/LCP Se0:18 (900316608): Port='Serial0:18' list=''
service=NET
*Mar 4 19:43:02.788: AAA/AUTHOR/LCP: Se0:18 (900316608) send AV service=ppp
*Mar 4 19:43:02.788: AAA/AUTHOR/LCP: Se0:18 (900316608) send AV protocol=lcp
*Mar 4 19:43:02.788: AAA/AUTHOR/LCP (900316608) found list "default"
*Mar 4 19:43:02.788: AAA/AUTHOR/LCP: Se0:18 (900316608) METHOD=RADIUS
*Mar 4 19:43:02.788: AAA/AUTHOR (900316608): Post authorization status = PASS_REPL
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar 4 19:43:02.788: Se0:18 CHAP: O SUCCESS id 2 len 4
*Mar 4 19:43:02.788: AAA/ACCT/NET/START User timeout, Port Serial0:18, List ""
*Mar 4 19:43:02.788: AAA/ACCT/NET: Found list "default"
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar 4 19:43:02.788: AAA/AUTHOR/FSM Se0:18 (3608739008): Port='Serial0:18' list=''
service=NET
*Mar 4 19:43:02.788: AAA/AUTHOR/FSM: Se0:18 (3608739008) send AV service=ppp
*Mar 4 19:43:02.788: AAA/AUTHOR/FSM: Se0:18 (3608739008) send AV protocol=ip
*Mar 4 19:43:02.788: AAA/AUTHOR/FSM (3608739008) found list "default"
*Mar 4 19:43:02.788: AAA/AUTHOR/FSM: Se0:18 (3608739008) METHOD=RADIUS
*Mar 4 19:43:02.788: RADIUS: Using NAS default peer
*Mar 4 19:43:02.788: RADIUS: Authorize IP address 0.0.0.0
*Mar 4 19:43:02.788: AAA/AUTHOR (3608739008): Post authorization status = PASS_REPL
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/FSM: We can start IPCP
*Mar 4 19:43:02.788: Se0:18 AAA/AUTHOR/FSM: (0): Can we start CDPCP?
*Mar 4 19:43:02.792: AAA/AUTHOR/FSM Se0:18 (3955392150): Port='Serial0:18' list=''
service=NET
*Mar 4 19:43:02.792: AAA/AUTHOR/FSM: Se0:18 (3955392150) send AV service=ppp
*Mar 4 19:43:02.792: AAA/AUTHOR/FSM: Se0:18 (3955392150) send AV protocol=cdp
*Mar 4 19:43:02.792: AAA/AUTHOR/FSM (3955392150) found list "default"
*Mar 4 19:43:02.792: AAA/AUTHOR/FSM: Se0:18 (3955392150) METHOD=RADIUS
*Mar 4 19:43:02.792: AAA/AUTHOR (3955392150): Post authorization status = PASS_REPL
*Mar 4 19:43:02.792: Se0:18 AAA/AUTHOR/FSM: We can start CDPCP
*Mar 4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:43:02.804: Se0:18 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:43:02.808: Se0:18 AAA/AUTHOR/FSM: Check for unauthorized mandatory AV's
*Mar 4 19:43:02.808: Se0:18 AAA/AUTHOR/FSM: Processing AV service=ppp
*Mar 4 19:43:02.808: Se0:18 AAA/AUTHOR/FSM: Succeeded
*Mar 4 19:43:02.816: Se0:18 AAA/AUTHOR/IPCP: Start. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:43:02.816: AAA/AUTHOR/IPCP Se0:18 (2267743837): Port='Serial0:18' list=''
service=NET
*Mar 4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) send AV service=ppp
*Mar 4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) send AV protocol=ip
*Mar 4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) send AV addr*10.1.1.3
*Mar 4 19:43:02.816: AAA/AUTHOR/IPCP (2267743837) found list "default"
*Mar 4 19:43:02.816: AAA/AUTHOR/IPCP: Se0:18 (2267743837) METHOD=RADIUS
*Mar 4 19:43:02.816: RADIUS: Using NAS default peer
*Mar 4 19:43:02.816: RADIUS: Authorize IP address 10.1.1.3
*Mar 4 19:43:02.816: AAA/AUTHOR (2267743837): Post authorization status = PASS_REPL
*Mar 4 19:43:02.816: Se0:18 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:43:02.820: Se0:18 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar 4 19:43:02.820: Se0:18 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:43:02.820: Se0:18 AAA/AUTHOR/IPCP: Done. Her address 10.1.1.3,
we want 10.1.1.3
*Mar 4 19:43:02.824: Se0:18 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar 4 19:43:02.824: Se0:18 AAA/PER-USER: processing author params.
access-3#show caller
Active Idle
Line User Service Time Time
Se0:18 timeout PPP 00:00:19 00:00:19
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout 00:01:30 00:01:00 00:00:37
access-3#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout 00:01:30 00:01:00 00:00:57
access-3#show caller user timeout
User: timeout, line Se0:18, service PPP
Active time 00:00:38, Idle time 00:00:10
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:00:51 00:00:49
PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP, CDPCP
Dialer: Connected to 4085551200, inbound
Idle timer 60 secs, idle 10 secs
Type is ISDN, group Serial0:23
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 51 packets input, 2104 bytes, 0 no buffer
11 input errors, 2 CRC, 3 frame, 0 overrun
58 packets output, 2233 bytes, 0 underruns
0 output errors, 0 collisions, 45 interface resets
access-3#show caller user timeout
User: timeout, line Se0:18, service PPP
Active time 00:00:45, Idle time 00:00:17
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:00:44 00:00:42
PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP, CDPCP
Dialer: Connected to 4085551200, inbound
Idle timer 60 secs, idle 17 secs
Type is ISDN, group Serial0:23
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 52 packets input, 2120 bytes, 0 no buffer
11 input errors, 2 CRC, 3 frame, 0 overrun
59 packets output, 2249 bytes, 0 underruns
0 output errors, 0 collisions, 45 interface resets
access-3#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/34/40 ms
access-3#show caller user timeout
User: timeout, line Se0:18, service PPP
Active time 00:01:02, Idle time 00:00:04
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:00:27 00:00:55
PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP, CDPCP
Dialer: Connected to 4085551200, inbound
Idle timer 60 secs, idle 4 secs
Type is ISDN, group Serial0:23
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 60 packets input, 2688 bytes, 0 no buffer
11 input errors, 2 CRC, 3 frame, 0 overrun
67 packets output, 2817 bytes, 0 underruns
0 output errors, 0 collisions, 45 interface resets
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout 00:01:30 00:01:00 00:00:21
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout 00:01:30 00:01:00 00:00:07
access-3#
*Mar 4 19:44:33.788: ISDN Se0:23: TX -> DISCONNECT pd = 8 callref = 0x800E
*Mar 4 19:44:33.788: Cause i = 0x8090 - Normal call clearing
*Mar 4 19:44:33.840: ISDN Se0:23: RX <- RELEASE pd = 8 callref = 0x0E
*Mar 4 19:44:33.852: Se0:18 AAA/ACCT: ISDN xmit 64000 recv 64000 hwidb 612048BC
*Mar 4 19:44:33.852: AAA/ACCT/NET/STOP User timeout, Port Serial0:18:
task_id=14 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=5
disc-cause-ext=1100 pre-bytes-in=101 pre-bytes-out=102 pre-paks-in=5 pre-paks-out=5
bytes_in=2258 bytes_out=2276 paks_in=38 paks_out=38 pre-session-time=2 elapsed_time=91
nas-rx-speed=64000 nas-tx-speed=64000
*Mar 4 19:44:33.852: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x800E
*Mar 4 19:44:33.856: Se0:18 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar 4 19:44:33.856: Se0:18 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:44:34.060: TAC+: (3492368360): received acct response status = SUCCESS
إستدعاء ISDN أحادي القناة غير متعدد الارتباطات مع ملفات التعريف الظاهرية
أدناه نفس مستخدم ISDN أحادي القناة غير متعدد الارتباطات ولكن هذه المرة مع تمكين ملفات التعريف الظاهرية. لاحظ أنه يتم إنشاء واجهة vaccess حتى ولو لم يتم التفاوض حول الارتباط المتعدد ونقوم بإنشاء أوامر التكوين لتثبيت وحدات التوقيت.
*Mar 4 19:45:00.480: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x0C
*Mar 4 19:45:00.480: Bearer Capability i = 0x8890
*Mar 4 19:45:00.480: Channel ID i = 0xA98393
*Mar 4 19:45:00.480: Calling Party Number i = '!', 0x80, '4085551200'
*Mar 4 19:45:00.480: Called Party Number i = 0xA1, '4085703930'
*Mar 4 19:45:00.480: ISDN Se0:23: TX -> CALL_PROC pd = 8 callref = 0x800C
*Mar 4 19:45:00.480: Channel ID i = 0xA98393
*Mar 4 19:45:00.492: ISDN Se0:23: TX -> CONNECT pd = 8 callref = 0x800C
*Mar 4 19:45:00.492: Channel ID i = 0xA98393
*Mar 4 19:45:00.564: ISDN Se0:23: RX <- CONNECT_ACK pd = 8 callref = 0x0C
*Mar 4 19:45:00.804: Se0:18 PPP: Treating connection as a callin
*Mar 4 19:45:00.804: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:45:02.804: Se0:18 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:45:02.828: Se0:18 PPP: Phase is AUTHENTICATING, by this end
*Mar 4 19:45:02.828: Se0:18 CHAP: O CHALLENGE id 3 len 26 from "STACK"
*Mar 4 19:45:02.860: Se0:18 CHAP: I RESPONSE id 3 len 30 from "timeout"
*Mar 4 19:45:02.860: AAA: parse NAME=Serial0:18 idb TYPE=12 tty=-1
*Mar 4 19:45:02.860: AAA: NAME=Serial0:18 flags=0x51 TYPE=1 shelf=0 slot=0
adapter=0 port=0 channel=18
*Mar 4 19:45:02.860: AAA: parse NAME= idb TYPE=-1 tty=-1
*Mar 4 19:45:02.860: RADIUS: ustruct sharecount=1
*Mar 4 19:45:02.860: RADIUS: Initial Transmit Serial0:18 id 6 172.16.24.117:1645,
Access-Request, len 104
*Mar 4 19:45:02.860: Attribute 4 6 AC101874
*Mar 4 19:45:02.860: Attribute 5 6 00004E32
*Mar 4 19:45:02.860: Attribute 61 6 00000002
*Mar 4 19:45:02.864: Attribute 1 11 74696D65
*Mar 4 19:45:02.864: Attribute 30 12 34303835
*Mar 4 19:45:02.864: Attribute 31 12 34303835
*Mar 4 19:45:02.864: Attribute 3 19 03D4E134
*Mar 4 19:45:02.864: Attribute 6 6 00000002
*Mar 4 19:45:02.864: Attribute 7 6 00000001
*Mar 4 19:45:02.868: RADIUS: Received from id 6 172.16.24.117:1645, Access-Accept, len 50
*Mar 4 19:45:02.868: Attribute 6 6 00000002
*Mar 4 19:45:02.868: Attribute 7 6 00000001
*Mar 4 19:45:02.868: Attribute 8 6 FFFFFFFE
*Mar 4 19:45:02.868: Attribute 27 6 0000005A
*Mar 4 19:45:02.868: Attribute 28 6 0000003C
*Mar 4 19:45:02.868: Se0:18 AAA/AUTHOR/LCP: Authorize LCP
*Mar 4 19:45:02.868: AAA/AUTHOR/LCP Se0:18 (2825271150): Port='Serial0:18' list=''
service=NET
*Mar 4 19:45:02.868: AAA/AUTHOR/LCP: Se0:18 (2825271150) send AV service=ppp
*Mar 4 19:45:02.868: AAA/AUTHOR/LCP: Se0:18 (2825271150) send AV protocol=lcp
*Mar 4 19:45:02.868: AAA/AUTHOR/LCP (2825271150) found list "default"
*Mar 4 19:45:02.868: AAA/AUTHOR/LCP: Se0:18 (2825271150) METHOD=RADIUS
*Mar 4 19:45:02.872: AAA/AUTHOR (2825271150): Post authorization status = PASS_REPL
*Mar 4 19:45:02.872: Se0:18 AAA/AUTHOR/LCP: Processing AV service=ppp
*Mar 4 19:45:02.872: Se0:18 AAA/AUTHOR/LCP: Processing AV timeout=90
*Mar 4 19:45:02.872: Se0:18 AAA/AUTHOR/LCP: Processing AV idletime=60
*Mar 4 19:45:02.872: AAA/AUTHOR/LCP Se0:18: Per-user interface config created:
timeout absolute 1 30
ppp timeout idle 60
*Mar 4 19:45:02.872: Se0:18 CHAP: O SUCCESS id 3 len 4
*Mar 4 19:45:02.872: AAA/ACCT/NET/START User timeout, Port Serial0:18, List ""
*Mar 4 19:45:02.872: AAA/ACCT/NET: Found list "default"
*Mar 4 19:45:02.872: Vi1 VTEMPLATE: Reuse Vi1, recycle queue size 0
*Mar 4 19:45:02.872: Vi1 VTEMPLATE: Hardware address 00e0.1e81.636c
*Mar 4 19:45:02.872: Vi1 VTEMPLATE: Has a new cloneblk vtemplate, now it has vtemplate
*Mar 4 19:45:02.872: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:45:02.872: Vi1 VTEMPLATE: Clone from Virtual-Template1
interface Virtual-Access1
default ip address
no ip address
encap ppp
ip unnumbered Loopback0
ip access-group 199 in
ip helper-address 172.16.24.118
no ip directed-broadcast
ip accounting output-packets
ip nat inside
no keepalive
peer default ip address pool default
compress mppc
ppp callback accept
ppp authentication chap pap ms-chap
ppp multilink
multilink max-links 2
end
enabling payload compression on this interface.
*Mar 4 19:45:02.952: Vi1 VTEMPLATE: Has a new cloneblk AAA, now it has vtemplate/AAA
*Mar 4 19:45:02.952: Vi1 VTEMPLATE: ************* CLONE VACCESS1 *****************
*Mar 4 19:45:02.952: Vi1 VTEMPLATE: Clone from AAA
interface Virtual-Access1
timeout absolute 1 30
ppp timeout idle 60
end
*Mar 4 19:45:02.976: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
*Mar 4 19:45:02.976: Vi1 PPP: Treating connection as a dedicated line
*Mar 4 19:45:02.976: Vi1 AAA/AUTHOR/FSM: (0): LCP succeeds trivially
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/FSM: (0): Can we start IPCP?
*Mar 4 19:45:02.980: AAA/AUTHOR/FSM Vi1 (2657898442): Port='Serial0:18' list='' service=NET
*Mar 4 19:45:02.980: AAA/AUTHOR/FSM: Vi1 (2657898442) send AV service=ppp
*Mar 4 19:45:02.980: AAA/AUTHOR/FSM: Vi1 (2657898442) send AV protocol=ip
*Mar 4 19:45:02.980: AAA/AUTHOR/FSM (2657898442) found list "default"
*Mar 4 19:45:02.980: AAA/AUTHOR/FSM: Vi1 (2657898442) METHOD=RADIUS
*Mar 4 19:45:02.980: RADIUS: Using NAS default peer
*Mar 4 19:45:02.980: RADIUS: Authorize IP address 0.0.0.0
*Mar 4 19:45:02.980: AAA/AUTHOR (2657898442): Post authorization status = PASS_REPL
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/FSM: We can start IPCP
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Start. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=0.0.0.0
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:45:02.980: Vi1 AAA/AUTHOR/IPCP: Done. Her address 0.0.0.0, we want 0.0.0.0
*Mar 4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Start. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:45:02.996: AAA/AUTHOR/IPCP Vi1 (1804338759): Port='Serial0:18' list=''
service=NET
*Mar 4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) send AV service=ppp
*Mar 4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) send AV protocol=ip
*Mar 4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) send AV addr*10.1.1.3
*Mar 4 19:45:02.996: AAA/AUTHOR/IPCP (1804338759) found list "default"
*Mar 4 19:45:02.996: AAA/AUTHOR/IPCP: Vi1 (1804338759) METHOD=RADIUS
*Mar 4 19:45:02.996: RADIUS: Using NAS default peer
*Mar 4 19:45:02.996: RADIUS: Authorize IP address 10.1.1.3
*Mar 4 19:45:02.996: AAA/AUTHOR (1804338759): Post authorization status = PASS_REPL
*Mar 4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Processing AV service=ppp
*Mar 4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Processing AV addr=10.1.1.3
*Mar 4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Authorization succeeded
*Mar 4 19:45:02.996: Vi1 AAA/AUTHOR/IPCP: Done. Her address 10.1.1.3, we want 10.1.1.3
*Mar 4 19:45:03.004: Vi1 AAA/AUTHOR/PER-USER: Event IP_UP
*Mar 4 19:45:03.004: Vi1 AAA/PER-USER: processing author params.
*Mar 4 19:45:03.996: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to up
access-3#show caller
Active Idle
Line User Service Time Time
Se0:18 timeout PPP 00:00:11 00:00:10
Vi1 timeout PPP VDP 00:00:11 00:00:10
access-3#show caller timeout
User: timeout, line Se0:18, service PPP
Active time 00:00:15, Idle time 00:00:15
Timeouts: Absolute Idle
Limits: - -
Disconnect in: - -
PPP: LCP Open, multilink Closed, CHAP (<- AAA)
Dialer: Connected to 4085551200, inbound
Idle timer 60 secs, idle 15 secs
Type is ISDN, group Serial0:23
IP: Local 10.1.1.1
Access list (I/O) is 199/not set
Counts: 81 packets input, 3291 bytes, 0 no buffer
11 input errors, 2 CRC, 3 frame, 0 overrun
87 packets output, 3419 bytes, 0 underruns
0 output errors, 0 collisions, 47 interface resets
User: timeout, line Vi1, service PPP VDP
Active time 00:00:15, Idle time 00:00:15
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:01:13 00:00:44
PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP
Idle timer 60 secs, idle 15 secs
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 7 packets input, 370 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
19 packets output, 404 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:40
access-3#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:58
access-3#show caller user timeout
User: timeout, line Se0:18, service PPP
Active time 00:00:34, Idle time 00:00:09
Timeouts: Absolute Idle
Limits: - -
Disconnect in: - -
PPP: LCP Open, multilink Closed, CHAP (<- AAA)
Dialer: Connected to 4085551200, inbound
Idle timer 60 secs, idle 9 secs
Type is ISDN, group Serial0:23
IP: Local 10.1.1.1
Access list (I/O) is 199/not set
Counts: 88 packets input, 3843 bytes, 0 no buffer
11 input errors, 2 CRC, 3 frame, 0 overrun
94 packets output, 3971 bytes, 0 underruns
0 output errors, 0 collisions, 47 interface resets
User: timeout, line Vi1, service PPP VDP
Active time 00:00:34, Idle time 00:00:09
Timeouts: Absolute Idle
Limits: 00:01:30 00:01:00
Disconnect in: 00:00:54 00:00:50
PPP: LCP Open, multilink Closed, CHAP (<- none), IPCP
Idle timer 60 secs, idle 9 secs
IP: Local 10.1.1.1, remote 10.1.1.3
Access list (I/O) is 199/not set
Counts: 14 packets input, 922 bytes, 0 no buffer
0 input errors, 0 CRC, 0 frame, 0 overrun
33 packets output, 956 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
access-3#show caller timeout
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:42
access-3#show caller timeouts
Session Idle Disconnect
Line User Timeout Timeout User in
Se0:18 timeout - - -
Vi1 timeout 00:01:30 00:01:00 00:00:22
access-3#show caller
Active Idle
Line User Service Time Time
Se0:18 timeout PPP 00:01:22 00:00:57
Vi1 timeout PPP VDP 00:01:22 00:00:57
access-3#
*Mar 4 19:46:28.996: Vi1 PPP: Idle timeout, dropping connection
*Mar 4 19:46:28.996: Se0:18 AAA/ACCT: ISDN xmit 64000 recv 64000 hwidb 612048BC
*Mar 4 19:46:28.996: AAA/ACCT/NET/STOP User timeout, Port Serial0:18:
task_id=15 timezone=PST service=ppp protocol=ip addr=10.1.1.3 disc-cause=4
disc-cause-ext=1021 pre-bytes-in=101 pre-bytes-out=102 pre-paks-in=5 pre-paks-out=5
bytes_in=1024 bytes_out=1036 paks_in=21 paks_out=21 pre-session-time=2 elapsed_time=86
nas-rx-speed=64000 nas-tx-speed=64000
*Mar 4 19:46:29.000: ISDN Se0:23: TX -> DISCONNECT pd = 8 callref = 0x800C
*Mar 4 19:46:29.000: Cause i = 0x8090 - Normal call clearing
*Mar 4 19:46:29.000: Vi1 AAA/AUTHOR/PER-USER: Event IP_DOWN
*Mar 4 19:46:29.000: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
*Mar 4 19:46:29.004: Vi1 VTEMPLATE: Free vaccess
*Mar 4 19:46:29.004: Vi1 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:46:29.052: ISDN Se0:23: RX <- RELEASE pd = 8 callref = 0x0C
*Mar 4 19:46:29.064: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x800C
*Mar 4 19:46:29.064: Se0:18 AAA/AUTHOR/PER-USER: Event LCP_DOWN
*Mar 4 19:46:29.208: TAC+: (3109010012): received acct response status = SUCCESS
*Mar 4 19:46:29.580: VTEMPLATE: Clean up dirty vaccess queue, size 1
*Mar 4 19:46:29.580: Vi1 VTEMPLATE: Found a dirty vaccess clone with vtemplate/AAA
*Mar 4 19:46:29.580: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:46:29.580: Vi1 VTEMPLATE: Unclone to-be-freed command#2
interface Virtual-Access1
default ppp timeout idle 60
default timeout absolute 1 30
end
*Mar 4 19:46:29.596: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:46:29.616: Vi1 VTEMPLATE: Remove cloneblk AAA with vtemplate/AAA
*Mar 4 19:46:29.616: Vi1 VTEMPLATE: ************ UNCLONE VACCESS1 **************
*Mar 4 19:46:29.616: Vi1 VTEMPLATE: Unclone to-be-freed command#15
interface Virtual-Access1
default multilink max-links 2
default ppp multilink
default ppp authentication chap pap ms-chap
default ppp callback accept
default compress mppc
default peer default ip address pool default
default keepalive
default ip nat inside
default ip accounting output-packets
default ip directed-broadcast
default ip helper-address 172.16.24.118
default ip access-group 199 in
default ip unnumbered Loopback0
default encap ppp
default ip address
end
*Mar 4 19:46:29.704: Vi1 VTEMPLATE: Set default settings with no ip address
*Mar 4 19:46:29.720: Vi1 VTEMPLATE: Remove cloneblk vtemplate with vtemplate/AAA
*Mar 4 19:46:29.720: Vi1 VTEMPLATE: Add vaccess to recycle queue, queue SIZE=1
*Mar 4 19:46:30.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1,
changed state to down
معلومات ذات صلة
محفوظات المراجعة
| المراجعة | تاريخ النشر | التعليقات |
|---|---|---|
1.0 |
04-Feb-2010 |
الإصدار الأولي |
التعليقات