Cisco Unified Contact Center Express Installation and Upgrade Guide, Release 10.5(1)
Server Configuration Table
Downloads: This chapterpdf (PDF - 1.17MB) The complete bookPDF (PDF - 2.27MB) | The complete bookePub (ePub - 177.0KB) | The complete bookMobi (Mobi - 271.0KB) | Feedback

Server Configuration Table

Server Configuration Table

Server Configuration Information for Installation


Note


  • You can use the configuration table for saving your entries either on a printed paper or in the PDF document.

  • Be aware that the field values (namely hostname and passwords) that you enter while you are running the installation program are case sensitive.

  • All the fields may not be applicable to your system and network configuration. Unless mentioned otherwise, you can change the values of most fields after the installation using CLI commands.


Attention:

Changes to some of the configuration parameters may result in changes to the licence MAC, and you may have to rehost the Unified CCX license. For information about the configuration parameters, see Unified CCX Licenses.

Table 1 Node Configuration Table

Parameter

Your Entry

Administrator ID

Attention:

You cannot change the original administrator account user ID; you can create additional administrator accounts.

Caution   

Do not create administrator IDs (for CLI access or Operating System administration) that start with "uccx" or "UCCX" because such IDs conflict with system account names that are used internally within the Unified CCX server.

 

Administrator Password

Attention:

This field specifies the password for the administrator account, which you use for secure shell access to the CLI, for logging in to Cisco Unified Communications Operating System Administration, and for logging in to the Disaster Recovery System. Ensure that the password is at least six characters long; it can contain alphanumeric characters, hyphens, and underscores.

You can change the password after installation.

 

Application User Name

 

Application User Password

Attention:

Use the Application User password as the default password for applications that are installed on the system, including Unified CCX and Unified Communications Manager. Ensure that the password is at least six characters long; it can contain alphanumeric characters, hyphens, and underscores.

You can change the password after installation.

 

DNS Primary

 

DNS Secondary (optional)

 

Domain

 

Gateway Address

 

Hostname

 

IP Address

 

IP Mask

 

MTU Size

Note   

Use the same Maximum Transmission Unit (MTU) value for all servers in the cluster.

 

NIC Duplex

Note   

This parameter is not displayed if automatic negotiation is used.

 

NIC Speed

Note   

This parameter is not displayed if automatic negotiation is used.

 
NTP Server
Attention:

Enter the hostname or IP address of one or more Network Time Protocol (NTP) servers with which you want to synchronize.

You can enter up to five NTP servers.

You can change the NTP server after installation.

 
Security Password
Attention:

Servers in the cluster use the Security password to communicate with one another. The password must contain at least six alphanumeric characters. It can contain hyphens and underscores, but it must start with an alphanumeric character.

Save this password. You will be asked to enter the same Security password when you install the second node to form a cluster.

You can change the password after installation by using the following CLI command:

CLI > set password user security

To avoid losing communications between nodes, you must change the Security password on both nodes in a cluster and reboot both the nodes. For more information, see the description of this command in the Cisco Unified Communications Operating System Administration Guide at http:/​/​www.cisco.com/​en/​US/​products/​sw/​custcosw/​ps1846/​products_​installation_​and_​configuration_​guides_​list.html.

 

SMTP Location

Note   

You must populate this field if you plan to use electronic notification.

 

Organization

Note   

The value you enter is used to generate a CSR.

 

Unit

Note   

The value you enter is used to generate a CSR.

 

Location

 

State

Note   

The value you enter is used to generate a CSR.

 

Country

Note   

The value you enter is used to generate a CSR and self-signed certificates.

 

Time Zone