Technical Specifications

This chapter contains the following sections:

Switch Specifications

Table 1. Cisco IE 4010 Switch Specifications

Environmental Ranges

Operating temperature

Note

 
Operating temperatures exceeding 60°C are not covered by the product safety certifications and approvals. However, the switch can function in the installations under the environmental conditions listed.

-40°C to +74°C

  • -40°C to +75°C (Vented Enclosure Operating- 40 LFM Air Flow)

  • -40°C to +60°C (Sealed Enclosure Operating- 0 LFM Air Flow)

  • -34°C to +75°C (Fan or Blower equipped Enclosure Operating- 200 LFM Air Flow)

  • -40°C to +85°C (IEC 60068-2-2 Environmental Type Tested to +85°C for 16 hours)

Note

 
The maximum operating temperature of the switch varies depending on the type of SFP module that you use.

Storage temperature

–40 to 185°F (–40 to 85°C)

Relative humidity

5 to 95% (noncondensing)

Operating altitude

Up to 13,800 ft (3049 m)

Storage altitude

Up to 15,000 ft (4570 m)

Thermal spacing

1.75 in. (4.4 cm)

Operational shock

50G at 11ms, half sine and 200G ar 2.11ms, half sine.

Non-Operational Shock

65-80G at 9ms, Trapezoidal

Physical Specifications

Weight

Without power supply: IE-4010-4S24P; 12.1 lbs (5.46 kg, IE-4010-16S12P: 12.7 lbs (5.78 kg)

  • PWR-RGD-AC-DC-H:2.55 lb (1.16 kg)

  • PWR-RGD-LOW-DC-H:2.5 lb (1.13 kg)

Dimensions (H x W x D)

1.75 x 17.5 x 15.0 in. (4.45 x 44.5 x 38.1 cm)
Table 2. Cisco IE 4010 Switch Power Requirements

Nominal input voltage

PWR-RGD-AC-DC-H:

100 to 240 VAC, 50 to 60 Hz

100 to 250 VDC

PWR-RGD-LOW-DC-H:

24 to 60 VDC

Absolute maximum (short term) input voltage

PWR-RGD-AC-DC-H:

85 to 265 VAC, 47 to 63 Hz

88 to 300 VDC

PWR-RGD-LOW-DC-H:

18 to 75 VDC

Maximum PoE power available to Powered Devices (PD), with one power supply module installed

80W

Maximum PoE power available to Powered Devices (PD), with two power supply modules installed

200W
Table 3. Table 15 Cisco IE 4010 Switch Power Consumption

Max Power at 60C

FRU Configuration

FRU Mode

IE-4010-4S24P

IE-4010-16S12P

Watts

BTU/hr

Watts

BTU/hr

With 2 power supplies (150W or 250W), PoE not enabled.

Redundant

65

222

70

239

With 1 power supply (150W or 250W), PoE not enabled.

-NA-

61

208

65

222

With 2 150W power supplies, PoE enabled

Load Shared

112

382

117

399

With 2 250W power supplies, PoE enabled

Load Shared

157

535

156

532

With 2 power supplies(150W and 250W), PoE enabled

Load Shared

133

454

138

471

Power-Supply Module Specifications

Table 4. Power Supply Module Physical Specifications

Weight

PWR-RGD-AC-DC-H

PWR-RGD-LOW-DC-H

2.55 lb (1.15 kg)

2.5 lb (1.13 kg)

Dimensions (H x W x D)

PWR-RGD-AC-DC-H and PWR-RGD-LOW-DC-H

1.58 x 7 x 5 in. (4 x 17.8 x 12.7 cm) (without mounting flanges)

1.58 x 8.15 x 5 in. (4 x 20.7 x 12.7 cm) (with mounting flanges)

Alarm Ratings

Table 5. Alarm Input and Output Ratings

Alarm input electrical specification

No external voltage needed to activate alarm inputs. The open circuit voltage between any Alarm input (1 to 4) and Alarm input Common is 5VDC and the loop current is 2 mA max per input.

Alarm output electrical specification

30VDC @ 1A, 48VDC @ 0.5A