A Show Commands

show (eigrp)

show { ip eigrp [eigrp-ptag] neighbors [ detail | state ] { [interface] | [address] [ vrf { vrf-name | vrf-known-name | all } ] } | ipv6 eigrp [eigrp-ptag] neighbors [ detail | state ] { [interface] | [ipv6-addr] [ vrf { vrf-name | vrf-known-name | all } ] } } [ __readonly__ TABLE_asn asn TABLE_vrf vrf [ TABLE_peer peer_handle peer_ipaddr peer_ipv6addr peer_ifname peer_holdtime peer_uptime peer_srtt peer_rto peer_xmitq_count peer_last_seqno peer_static peer_nsf_restart_time peer_last_startup_serno peer_ios_major_ver peer_ios_minor_ver peer_eigrp_major_rev peer_eigrp_minor_rev peer_retrans_count peer_retry_count peer_wait_for_init peer_wait_for_init_ack peer_reinit_start_time peer_prefix_count peer_info_stubbed peer_info_receive_only [ peer_info_allow_connected peer_info_allow_statics peer_info_allow_summaries peer_info_allow_redist peer_info_allow_leaking ] [ peer_state_cr_mode peer_state_need_init peer_state_need_init_ack peer_state_going_down peer_state_coming_up peer_state_peer_deleted peer_state_nsf_in_progress peer_state_need_eot peer_state_use_nsf_startup_mode peer_state_await_nsf_convergence peer_state_initiated_gr peer_state_cr_sequence peer_state_rcv_probe_sequence peer_state_send_probe_sequence ] peer_suppress_queries [ TABLE_xmitq_pkts pkt_qtype pkt_index pkt_opcode pkt_ack_seqno pkt_start_seqno pkt_end_seqno pkt_len pkt_time_sent pkt_init_flag pkt_sequenced ] ] [ TABLE_suspended_peer susp_peer_ipaddr susp_peer_ipv6addr susp_peer_ifname susp_peer_restart_reqd susp_peer_restart_time ] ]

Syntax Description

show

Show running system information
ip

Display IP information
ipv6

Display IPv6 information
eigrp

Display EIGRP status and configuration
vrf

Display per-VRF information
vrf-name

Type: vrf

pattern: [-a-zA-Z0-9_:;$#@]*

antipattern: vrf | detail | interface | definition | context | forwarding | member | all | l2-vrf | topology | passive

length: 32

VRF name
vrf-known-name

Type: vrf

Known VRF name
all

Display information for all VRFs
eigrp-ptag

Type: string

pattern: [a-zA-Z0-9_][a-zA-Z0-9_-]*

antipattern: accounting | all | fsm | graceful-restart | interface | interfaces | internal | neighbor | neighbors | notifications | packets | prefix | route | route-map | shutdown | summary | topology | traffic | transmit | urib | vrf | vrf-events

length: 20

Process tag
neighbors

IP-EIGRP neighbors
detail

Show detailed peer information
state

Show detailed peer and state information
interface

Type: interface

Interface
address

Type: ipaddr

IP-EIGRP neighbor address
ipv6-addr

Type: ipv6addr

IPv6 neighbor address
__readonly__

TABLE_asn

asn

Type: uinteger
TABLE_vrf

vrf

Type: string
TABLE_peer

peer_handle

Type: uinteger
peer_ipaddr

Type: ipaddr
peer_ipv6addr

Type: ipv6addr
peer_ifname

Type: interface
peer_holdtime

Type: uinteger
peer_uptime

Type: duration
peer_srtt

Type: uinteger
peer_rto

Type: uinteger
peer_xmitq_count

Type: uinteger
peer_last_seqno

Type: uinteger
peer_static

Type: bool
peer_nsf_restart_time

Type: duration
peer_last_startup_serno

Type: uinteger
peer_ios_major_ver

Type: uinteger
peer_ios_minor_ver

Type: uinteger
peer_eigrp_major_rev

Type: uinteger
peer_eigrp_minor_rev

Type: uinteger
peer_retrans_count

Type: uinteger
peer_retry_count

Type: uinteger
peer_wait_for_init

Type: bool
peer_wait_for_init_ack

Type: bool
peer_reinit_start_time

Type: duration
peer_prefix_count

Type: uinteger
peer_info_stubbed

Type: bool
peer_info_receive_only

Type: bool
peer_info_allow_connected

Type: bool
peer_info_allow_statics

Type: bool
peer_info_allow_summaries

Type: bool
peer_info_allow_redist

Type: bool
peer_info_allow_leaking

Type: bool
peer_state_cr_mode

Type: bool
peer_state_need_init

Type: bool
peer_state_need_init_ack

Type: bool
peer_state_going_down

Type: bool
peer_state_coming_up

Type: bool
peer_state_peer_deleted

Type: bool
peer_state_nsf_in_progress

Type: bool
peer_state_need_eot

Type: bool
peer_state_use_nsf_startup_mode

Type: bool
peer_state_await_nsf_convergence

Type: bool
peer_state_initiated_gr

Type: bool
peer_state_cr_sequence

Type: uinteger
peer_state_rcv_probe_sequence

Type: uinteger
peer_state_send_probe_sequence

Type: uinteger
peer_suppress_queries

Type: bool
TABLE_xmitq_pkts

pkt_qtype

Type: uinteger
pkt_index

Type: uinteger
pkt_opcode

UPDATE  value: 1
REQUEST  value: 2
QUERY  value: 3
REPLY  value: 4
HELLO  value: 5
IPXSAP  value: 6
PROBE  value: 7
ACK  value: 8
STUB  value: 9
SIAQUERY  value: 10
SIAREPLY  value: 11
pkt_ack_seqno

Type: uinteger
pkt_start_seqno

Type: uinteger
pkt_end_seqno

Type: uinteger
pkt_len

Type: uinteger
pkt_time_sent

Type: duration
pkt_init_flag

Type: bool
pkt_sequenced

Type: bool
TABLE_suspended_peer

susp_peer_ipaddr

Type: ipaddr
susp_peer_ipv6addr

Type: ipv6addr
susp_peer_ifname

Type: interface
susp_peer_restart_reqd

Type: bool
susp_peer_restart_time

Type: uinteger

Command Modes

  • /exec

show aaa accounting

show aaa accounting [ __readonly__ [ TABLE_acctMethods service methods ] ]

Syntax Description

show

Show running system information
aaa

Show aaa information
accounting

Show accounting configuration
__readonly__

TABLE_acctMethods

service

Type: string

service type
methods

Type: string

Accounting methods configured for the application

Command Modes

  • /exec

show aaa authentication

show aaa authentication [ __readonly__ [ TABLE_AuthenMethods service method ] ]

Syntax Description

show

Show running system information
aaa

Show aaa information
authentication

Show authentication configuration
__readonly__

TABLE_AuthenMethods

service

Type: string

Service for which authentication is needed
method

Type: string

Authentication method used for the service

Command Modes

  • /exec

show aaa authentication login

show aaa authentication login { mschap | mschapv2 | chap }

Syntax Description

show

Show running system information
aaa

Show aaa information
authentication

Show authentication configuration
login

Show authentication login error message configuration
mschap

Show authentication login MSCHAP enable configuration
mschapv2

Show authentication login MSCHAP V2 enable configuration
chap

Show authentication login CHAP enable configuration

Command Modes

  • /exec

show aaa authentication login ascii-authentication

show aaa authentication login ascii-authentication [ __readonly__ ascii_authen_status ]

Syntax Description

show

Show running system information
aaa

Show aaa information
authentication

Show authentication configuration
login

Show authentication login message configuration
ascii-authentication

Show ascii-authentication configuration
__readonly__

ascii_authen_status

ascii authentication status

disabled  value: 0
enabled  value: 1

Command Modes

  • /exec

show aaa authentication login error-enable

show aaa authentication login error-enable [ __readonly__ [status] ]

Syntax Description

show

Show running system information
aaa

Show aaa information
authentication

Show authentication configuration
login

Show authentication login error message configuration
error-enable

Show authentication login error message enable configuration
__readonly__

status

login error-enable enabled or disabled

disabled  value: 0
enabled  value: 1

Command Modes

  • /exec

show aaa authentication login password-aging

show aaa authentication login password-aging [ __readonly__ passwordAging_status ]

Syntax Description

show

Show running system information
aaa

Show aaa information
authentication

Show authentication configuration
login

Show authentication login error message configuration
password-aging

Show password-aging enable configuration
__readonly__

passwordAging_status

login password-aging

disabled  value: 0
enabled  value: 1

Command Modes

  • /exec

show aaa authorization

show aaa authorization [all] [ __readonly__ [ pki_ssh_cert_author pki_ssh_pubkey_author ] [ TABLE_cmd_methods appl_subtype cmd_type methods ] [ TABLE_app_methods appl methods ] ]

Syntax Description

show

Show running system information
aaa

Show aaa information
authorization

Show authorization configuration
all

Show all(include defaults configurations) authorization info
__readonly__

pki_ssh_cert_author

Type: string
pki_ssh_pubkey_author

Type: string
TABLE_cmd_methods

table containing command authorization methods
appl_subtype

Type: string
cmd_type

Type: string
methods

Type: string
TABLE_app_methods

table containing application authorization methods
appl

Type: string
methods

Type: string

Command Modes

  • /exec

show aaa groups

show aaa groups [ __readonly__ TABLE_groups group ]

Syntax Description

show

Show running system information
aaa

Show aaa information
groups

Show configured groups
__readonly__

TABLE_groups

Table showing aaa groups
group

Type: string

Name of the group

Command Modes

  • /exec

show aaa user default-role

show aaa user default-role [ __readonly__ default_role_status udr_status ]

Syntax Description

show

Show running system information
aaa

Show aaa information
user

Remotely authenticated user
default-role

Default role assigned by aaa-admin for remote authentication
__readonly__

default_role_status

user default role status
udr_status

Status of user default role

disabled  value: 0
enabled  value: 1

Command Modes

  • /exec

show access-lists

show [ip_ipv6_mac] access-lists [name] [ capture session capture_session ] [ expanded | summary | private | brief ] [ __readonly__ TABLE_ip_ipv6_mac op_ip_ipv6_mac acl_name [statistics] [frag_opt_permit_deny] [global_capture_session] [ TABLE_seqno seqno { permitdeny [ proto_str | proto | ip | ipv6 ] { src_any | src_ip_prefix | src_ip_addr src_ip_mask | src_ipv6_prefix | src_ipv6_addr src_ipv6_mask | mac_src mac_src_wild | src_addrgrp } [ src_port_op [src_port1_str] src_port1_num [ src_port2_str | src_port2_num ] | src_portgrp ] { dest_any | dest_ip_prefix | dest_ip_addr dest_ip_mask | dest_ipv6_prefix | dest_ipv6_addr dest_ipv6_mask | mac_dest mac_dest_wild | dest_addrgrp } [ dest_port_op [dest_port1_str] dest_port1_num [ dest_port2_str | dest_port2_num ] | dest_portgrp ] [ { icmp_type [icmp_code] | icmp_str } | { icmpv6_type [icmpv6_code] | icmpv6_str } ] [ igmp_type | igmp_type_str ] [ [ precedence | precedence_str ] [ tos | tos_str ] | [ dscp | dscp_str ] ] [log] [capture_session] [fragments] [ plen_op plen1 [plen2] ] [urg] [ack] [psh] [rst] [syn] [fin] [established] [flow_label] [timerange] [ eth_proto | eth_proto_str ] [vlan] [cos] [match_count] | remark } ] ]

Syntax Description

show

Show running system information
name

Type: string

length: 64

List name
ip_ipv6_mac

IP/IPv6/MAC

ip  value: 9
Display IP information
ipv6  value: 10
Display IPv6 information
mac  value: 11
MAC configuration commands
capture

capture Not available in this release.
session

session
capture_session

Type: uinteger

min: 1  max: 48  

session id
op_ip_ipv6_mac

IP/IPv6/MAC

ip  value: 9
Display IP information
ipv6  value: 10
Display IPv6 information
mac  value: 11
MAC configuration commands
access-lists

List access lists
acl_name

Type: string

length: 64

List name
__readonly__

TABLE_ip_ipv6_mac

frag_opt_permit_deny

frag_op_type

deny-all  value: 3
Drop all fragments
permit-all  value: 2
Alllow all fragments
seqno

Type: uinteger

min: 1  max: 4294967295  

Sequence number
permitdeny

Permit/deny

permit  value: 2
Specify packets to forward
deny  value: 3
Specify packets to reject
proto

Type: uinteger

min: 0  max: 255  

A protocol number
TABLE_seqno

proto_str

Type: string

Protocol name
ip

IP

ip  value: 1
IP Protocol
ipv6

IPV6

ipv6  value: 1
IPv6 Protocol
src_any

SRCAny

any  value: 1
Any IP address
dest_any

DESTAny

any  value: 1
Any IP address
src_ip_prefix

Type: ipprefix

Source IP prefix
src_ip_addr

Type: ipaddr

Source IP address
src_ip_mask

Type: ipaddr

Source IP mask
src_ipv6_prefix

Type: ipv6prefix

Source IPv6 prefix
src_ipv6_addr

Type: ipv6addr

Source IP address
src_ipv6_mask

Type: ipv6addr

Source IP mask
mac_src

Type: ethernet

Source MAC address
mac_src_wild

Type: ethernet

Source MAC mask
dest_ip_prefix

Type: ipprefix

Destination IP prefix
dest_ip_addr

Type: ipaddr

Destination IP address
dest_ip_mask

Type: ipaddr

Destination IP mask
dest_ipv6_prefix

Type: ipv6prefix

Destination IPv6 prefix
dest_ipv6_addr

Type: ipv6addr

Destination IP address
dest_ipv6_mask

Type: ipv6addr

Destination IP mask
mac_dest

Type: ethernet

Destination MAC address
mac_dest_wild

Type: ethernet

Destination MAC mask
src_port_op

Source Port operator

lt  value: 4
Match only packets with a lower port number
gt  value: 5
Match only packets with a greater port number
eq  value: 6
Match only packets on a given port number
neq  value: 7
Match only packets not on a given port number
range  value: 8
Match only packets in the range of port numbers
dest_port_op

Destination Port operator

lt  value: 4
Match only packets with a lower port number
gt  value: 5
Match only packets with a greater port number
eq  value: 6
Match only packets on a given port number
neq  value: 7
Match only packets not on a given port number
range  value: 8
Match only packets in the range of port numbers
src_port1_str

Type: string

Source port name
src_port1_num

Type: uinteger

Source port number
src_port2_str

Type: string

Source port name
src_port2_num

Type: uinteger

Source port number
dest_port1_str

Type: string

Destination port name
dest_port1_num

Type: uinteger

Destination port number
dest_port2_str

Type: string

Destination port name
dest_port2_num

Type: uinteger

Destination port number
icmp_type

Type: uinteger

ICMP type
icmp_code

Type: uinteger

ICMP code
icmp_str

Type: string

ICMP message
icmpv6_type

Type: uinteger

ICMP type
icmpv6_code

Type: uinteger

ICMP code
icmpv6_str

Type: string

ICMP message
igmp_type

Type: uinteger

IGMP type
igmp_type_str

Type: string

IGMP type String
precedence

Type: uinteger

precedence
precedence_str

Type: string

precedence string
tos

Type: uinteger

tos
tos_str

Type: string

tos string
dscp

Type: uinteger

dscp
dscp_str

Type: string

dscp string
capture_session

Type: uinteger

min: 1  max: 48  

capture session
global_capture_session

Type: uinteger

min: 1  max: 48  

capture session
log

Log

enable  value: 1
Log the packet
disable  value: 2
Packet loging disabled
fragments

Fragments

enable  value: 1
Match on fragments
disable  value: 2
No fragment match
urg

URG

enable  value: 1
TCP urg flag set
disable  value: 2
TCP urg flag clear
ack

ACK

enable  value: 1
TCP ack flag set
disable  value: 2
TCP ack flag clear
psh

PSH

enable  value: 1
TCP psh flag set
disable  value: 2
TCP psh flag clear
rst

RST

enable  value: 1
TCP rst flag set
disable  value: 2
TCP rst flag clear
syn

SYN

enable  value: 1
TCP syn flag set
disable  value: 2
TCP syn flag clear
fin

FIN

enable  value: 1
TCP fin flag set
disable  value: 2
TCP fin flag clear
established

ESTABLISHED

enable  value: 1
TCP established connection
disable  value: 2
TCP not established connection
flow_label

Type: uinteger

IPv6 flow label
timerange

Type: string

Time-range
eth_proto

Type: hex

MAC protocol number
eth_proto_str

Type: string

MAC protocol name
vlan

Type: integer

min: 0  max: 4095  

VLAN number
cos

Type: integer

min: 0  max: 7  

CoS value
match_count

Type: longlong

Number of packets matching the ACL
remark

Type: string

Remark String
statistics

STATISTICS

enable  value: 1
Statistics enabled for ACL
disable  value: 2
Statistics not enabled for ACL
src_addrgrp

Type: string

Source address group
dest_addrgrp

Type: string

Destination address group
src_portgrp

Type: string

Source port group
dest_portgrp

Type: string

Destination port group
plen_op

Source Port operator

lt  value: 4
Match only packets with a lower packet length
gt  value: 5
Match only packets with a greater packet length
eq  value: 6
Match only packets on a given packet length
neq  value: 7
Match only packets not on a given packet length
range  value: 8
Match only packets in the range of packet lengths
plen1

Type: uinteger

Packet length minimum
plen2

Type: uinteger

packet length maximum
expanded

EXPANDED

expanded  value: 1
Expand groups
summary

SUMMARY

summary  value: 1
access list summary
private

PRIVATE

dynamic  value: 1
Dynamic ACLs
brief

BRIEF

brief  value: 1
print only aclnames with given capture session

Command Modes

  • /exec

show accounting log

show accounting log [ i0 | start-time SYYYY SMonth SDate STime [ end-time EYYYY EMonth EDate ETime ] ]

Syntax Description

show

Show running system information
accounting

Show Accounting Information
log

Show Accounting Log
i0

Type: integer

min: 0  max: 500000  

Log Size(in bytes)
start-time

Show messages from a given start-time
SYYYY

Type: integer

min: 1970  max: 2030  

Enter year in YYYY format
SMonth

Type: string

length: 3

Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
SDate

Type: integer

min: 1  max: 31  

Enter day of month in dd format
STime

Type: string

length: 8

Enter hour, minutes, seconds as HH:MM:SS
end-time

Show messages from a given end-time
EYYYY

Type: integer

min: 1970  max: 2030  

Enter year in YYYY format
EMonth

Type: string

length: 3

Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
EDate

Type: integer

min: 1  max: 31  

Enter day of month in dd format
ETime

Type: string

length: 8

Enter hour, minutes, seconds as HH:MM:SS

Command Modes

  • /exec

show accounting log all

show accounting log all

Syntax Description

show

Show running system information
accounting

Show accounting configuration
log

Show Accounting Log

all

Display accounting log including show commands (Use <terminal log-all> to enable show command accounting)

Command Modes

  • /exec

show accounting log last-index

show accounting log last-index [ __readonly__ last_index ]

Syntax Description

show

Show running system information
accounting

Show accounting configuration
log

Show Accounting Log

last-index

Show accounting log last index information
__readonly__

last_index

Type: integer

accounting log last index

Command Modes

  • /exec

show accounting log nvram

show accounting log nvram [ i0 | start-time SYYYY SMonth SDate STime [ end-time EYYYY EMonth EDate ETime ] ]

Syntax Description

show

Show running system information
accounting

Show Accounting Information
log

Show Accounting Log
nvram

present in nvram
i0

Type: integer

min: 0  max: 500000  

Log Size(in bytes)
start-time

Show messages from a given start-time
SYYYY

Type: integer

min: 1970  max: 2030  

Enter year in YYYY format
SMonth

Type: string

length: 3

Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
SDate

Type: integer

min: 1  max: 31  

Enter day of month in dd format
STime

Type: string

length: 8

Enter hour, minutes, seconds as HH:MM:SS
end-time

Show messages from a given end-time
EYYYY

Type: integer

min: 1970  max: 2030  

Enter year in YYYY format
EMonth

Type: string

length: 3

Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
EDate

Type: integer

min: 1  max: 31  

Enter day of month in dd format
ETime

Type: string

length: 8

Enter hour, minutes, seconds as HH:MM:SS

Command Modes

  • /exec

show accounting log nvram last-index

show accounting log nvram last-index

Syntax Description

show

Show running system information
accounting

Show accounting configuration
log

Show Accounting Log

nvram

present in nvram
last-index

Show accounting log last index information

Command Modes

  • /exec

show accounting log nvram start-seqnum

show accounting log nvram start-seqnum SSEQNUM [ end-seqnum ESEQNUM ]

Syntax Description

show

Show running system information
accounting

Show Accounting Information
log

Show Accounting Log

nvram

present in nvram
start-seqnum

Show messages starting from a given sequence number
end-seqnum

Show messages ending with a given sequence number
SSEQNUM

Type: integer

min: 1  max: 2000000000  

Enter Starting Sequence Number
ESEQNUM

Type: integer

min: 1  max: 2000000000  

Enter Starting Sequence Number

Command Modes

  • /exec

show accounting log start-seqnum

show accounting log start-seqnum SSEQNUM [ end-seqnum ESEQNUM ]

Syntax Description

show

Show running system information
accounting

Show Accounting Information
log

Show Accounting Log
start-seqnum

Show messages starting from a given sequence number
end-seqnum

Show messages ending with a given sequence number
SSEQNUM

Type: integer

min: 1  max: 2000000000  

Enter Starting Sequence Number
ESEQNUM

Type: integer

min: 1  max: 2000000000  

Enter Starting Sequence Number

Command Modes

  • /exec

show acl status

show acl status [ __readonly__ [status_log_string] ]

Syntax Description

show

Show running system information
acl

Show information about acl
status

Shows the status of last acl operation
__readonly__

status_log_string

Type: string

ppf entry string

Command Modes

  • /exec

show arp access-lists

show arp access-lists [name] [ __readonly__ TABLE_arp arp_name [ TABLE_seqno seqno permitdeny reqresp ip { sender_ip_any | { sender_host sender_ip | sender_net_ip sender_ip_mask } } [ target_ip_any | { target_host target_ip | target_net_ip target_ip_mask } ] mac { sender_mac_any | { sender_mac_host sender_mac | sender_net_mac sender_mac_mask } } [ target_mac_any | { target_mac_host target_mac | target_net_mac target_mac_mask } ] [arp_log] | remark ] ] [ capture session session-id ]

Syntax Description

show

Show running system information
arp

ARP access-lists Not available in this release.
access-lists

List access lists
name

Type: string

length: 64

List name
__readonly__

arp_name

Type: string

Name of the ARP ACL
seqno

Type: uinteger

min: 1  max: 4294967295  

Sequence number
permitdeny

Permit/deny

permit  value: 2
Specify packets to forward
deny  value: 3
Specify packets to reject
ip

Any IP protocol
TABLE_arp

TABLE_seqno

reqresp

ARP_Request

request  value: 1
response  value: 2
sender_ip_any

Any

any  value: 1
Any IP address
sender_host

Host

host  value: 1
host IP address
sender_ip

Type: ipaddr

IP address <a.b.c.d>
sender_net_ip

Type: ipaddr

IP address <a.b.c.d>
sender_ip_mask

Type: ipaddr

IP mask <a.b.c.d>
target_ip_any

Any

any  value: 1
Any IP address
target_host

Host

host  value: 1
host IP address
target_ip

Type: ipaddr

IP address <a.b.c.d>
target_net_ip

Type: ipaddr

IP address <a.b.c.d>
target_ip_mask

Type: ipaddr

IP mask <a.b.c.d>
mac

MAC configuration commands
sender_mac_any

Any

any  value: 1
Any MAC address
sender_mac_host

Host

host  value: 1
host MAC address
sender_mac

Type: ethernet

MAC address EEEE.EEEE.EEEE
sender_net_mac

Type: ethernet

MAC address EEEE.EEEE.EEEE
sender_mac_mask

Type: ethernet

MAC mask EEEE.EEEE.EEEE
target_mac_any

Any

any  value: 1
Any MAC address
target_mac_host

Host

host  value: 1
host MAC address
target_mac

Type: ethernet

MAC address EEEE.EEEE.EEEE
target_net_mac

Type: ethernet

MAC address EEEE.EEEE.EEEE
target_mac_mask

Type: ethernet

MAC mask EEEE.EEEE.EEEE
remark

Type: string

Remark String
arp_log

Log

log  value: 1
capture

Enable packet capture on this filter for session Not available in this release.
session

Session ID <1-48> for this session
session-id

Type: uinteger

min: 1  max: 48  

Session ID <1-48> for this session

Command Modes

  • /exec