System Setup and Software Installation Guide for Cisco NCS 1004

PDF

System Setup and Software Installation Guide for Cisco NCS 1004

Verify status of hardware components

Updated: July 17, 2026

Want to summarize with AI?

Log in

Use this procedure to verify the status of all the hardware components installed on NCS 1004.

Before you begin

Ensure that all required hardware components are installed on NCS 1004. For installation details, see the Cisco Network Convergence System 1004 Hardware Installation Guide.

Procedure

1.

Enter the show platform command in Cisco IOS XR EXEC mode to display the status of Cisco IOS XR.

Example:

RP/0/RP0/CPU0:ios# show platform
Wed Mar  4 06:21:26.929 UTC
Node              Type                       State             Config state
--------------------------------------------------------------------------------
0/0               NCS1K4-LC-FILLER           PRESENT           NSHUT
0/1               NCS1K4-1.2T-K9             OPERATIONAL       NSHUT
0/2               NCS1K4-1.2TL-K9            OPERATIONAL       NSHUT
0/3               NCS1K4-LC-FILLER           PRESENT           NSHUT
0/RP0/CPU0        NCS1K4-CNTLR-K9(Active)    IOS XR RUN        NSHUT
0/FT0             NCS1K4-FAN                 OPERATIONAL       NSHUT
0/FT1             NCS1K4-FAN                 OPERATIONAL       NSHUT
0/FT2             NCS1K4-FAN                 OPERATIONAL       NSHUT
0/PM0             NCS1K4-AC-PSU              OPERATIONAL       NSHUT
0/PM1             NCS1K4-AC-PSU              OPERATIONAL       NSHUT
0/SC0             NCS1004                    OPERATIONAL       NSHUT
RP/0/RP0/CPU0:ios# show platform
Thu May  7 10:03:03.394 UTC
Node              Type                       State             Config state
--------------------------------------------------------------------------------
0/0               NCS1K4-1.2T-K9             OPERATIONAL       NSHUT
0/1               NCS1K4-OTN-XP              OPERATIONAL       NSHUT
0/2               NCS1K4-OTN-XP              OPERATIONAL       NSHUT
0/3               NCS1K4-OTN-XP              OPERATIONAL       NSHUT
0/RP0/CPU0        NCS1K4-CNTLR-K9(Active)    IOS XR RUN        NSHUT
0/FT0             NCS1K4-FAN                 OPERATIONAL       NSHUT
0/FT1             NCS1K4-FAN                 OPERATIONAL       NSHUT
0/FT2             NCS1K4-FAN                 OPERATIONAL       NSHUT
0/PM0             NCS1K4-DC-PSU              OPERATIONAL       NSHUT
0/PM1             NCS1K4-DC-PSU              OPERATIONAL       NSHUT
0/SC0             NCS1004                    OPERATIONAL       NSHUT

  1. If Cisco IOS XR is not operational, no output appears. Use the show sdr command in Cisco IOS XR mode to verify the state of the service domain router (SDR) on the node.

    This example shows sample output of the show sdr command in Cisco IOS XR mode. 

    RP/0/RP0/CPU0:ios# show sdr
Wed Mar  4 06:23:16.143 UTC
Type                  NodeName       NodeState      RedState       PartnerName
--------------------------------------------------------------------------------
NCS1K4-LC-FILLER      0/0            PRESENT                       N/A
NCS1K4-1.2T-K9        0/1            OPERATIONAL                   N/A
NCS1K4-1.2TL-K9       0/2            OPERATIONAL                   N/A
NCS1K4-LC-FILLER      0/3            PRESENT                       N/A
RP                    0/RP0/CPU0     IOS XR RUN     ACTIVE         NONE
NCS1K4-CNTLR-K9       0/RP0          OPERATIONAL                   N/A
NCS1K4-FAN            0/FT0          OPERATIONAL                   N/A
NCS1K4-FAN            0/FT1          OPERATIONAL                   N/A
NCS1K4-FAN            0/FT2          OPERATIONAL                   N/A
NCS1K4-AC-PSU         0/PM0          OPERATIONAL                   N/A
NCS1K4-AC-PSU         0/PM1          OPERATIONAL                   N/A
NCS1004               0/SC0          OPERATIONAL                   N/A

    RP/0/RP0/CPU0:ios# show sdr
Thu May  7 10:50:08.651 UTC
Type                  NodeName       NodeState      RedState       PartnerName
--------------------------------------------------------------------------------
NCS1K4-1.2T-K9        0/0            OPERATIONAL                   N/A
NCS1K4-OTN-XP         0/1            OPERATIONAL                   N/A
NCS1K4-OTN-XP         0/2            OPERATIONAL                   N/A
NCS1K4-OTN-XP         0/3            OPERATIONAL                   N/A
RP                    0/RP0/CPU0     IOS XR RUN     ACTIVE         NONE
NCS1K4-CNTLR-K9       0/RP0          OPERATIONAL                   N/A
NCS1K4-FAN            0/FT0          OPERATIONAL                   N/A
NCS1K4-FAN            0/FT1          OPERATIONAL                   N/A
NCS1K4-FAN            0/FT2          OPERATIONAL                   N/A
NCS1K4-DC-PSU         0/PM0          OPERATIONAL                   N/A
NCS1K4-DC-PSU         0/PM1          OPERATIONAL                   N/A
NCS1004               0/SC0          OPERATIONAL                   N/A
2.

Enter the admin command to enter System Admin EXEC mode.

Example:

 RP/0/RP0/CPU0:ios# admin
3.

Enter the show platform command to display the information and status of each node in the system.

Example:

sysadmin-vm:0_RP0# show platform
Wed Mar  4  06:24:46.700 UTC+00:00
Location  Card Type               HW State      SW State      Config State
----------------------------------------------------------------------------
0/0       NCS1K4-LC-FILLER        PRESENT       N/A           NSHUT
0/1       NCS1K4-1.2T-K9          OPERATIONAL   N/A           NSHUT
0/2       NCS1K4-1.2TL-K9         OPERATIONAL   N/A           NSHUT
0/3       NCS1K4-LC-FILLER        PRESENT       N/A           NSHUT
0/RP0     NCS1K4-CNTLR-K9         OPERATIONAL   OPERATIONAL   NSHUT
0/FT0     NCS1K4-FAN              OPERATIONAL   N/A           NSHUT
0/FT1     NCS1K4-FAN              OPERATIONAL   N/A           NSHUT
0/FT2     NCS1K4-FAN              OPERATIONAL   N/A           NSHUT
0/PM0     NCS1K4-AC-PSU           OPERATIONAL   N/A           NSHUT
0/PM1     NCS1K4-AC-PSU           OPERATIONAL   N/A           NSHUT
0/SC0     NCS1004                 OPERATIONAL   N/A           NSHUT

sysadmin-vm:0_RP0# show platform
Thu May  7  10:58:09.331 UTC+00:00
Location  Card Type               HW State      SW State      Config State
----------------------------------------------------------------------------
0/0       NCS1K4-1.2T-K9          OPERATIONAL   N/A           NSHUT
0/1       NCS1K4-OTN-XP           OPERATIONAL   N/A           NSHUT
0/2       NCS1K4-OTN-XP           OPERATIONAL   N/A           NSHUT
0/3       NCS1K4-OTN-XP           OPERATIONAL   N/A           NSHUT
0/RP0     NCS1K4-CNTLR-K9         OPERATIONAL   OPERATIONAL   NSHUT
0/FT0     NCS1K4-FAN              OPERATIONAL   N/A           NSHUT
0/FT1     NCS1K4-FAN              OPERATIONAL   N/A           NSHUT
0/FT2     NCS1K4-FAN              OPERATIONAL   N/A           NSHUT
0/PM0     NCS1K4-DC-PSU           OPERATIONAL   N/A           NSHUT
0/PM1     NCS1K4-DC-PSU           OPERATIONAL   N/A           NSHUT
0/SC0     NCS1004                 OPERATIONAL   N/A           NSHUT

Ensure that the output displays all NCS 1004 components. Both the hardware and software states must be OPERATIONAL.

The various hardware and software states are:

Hardware states

  • OPERATIONAL: node is operating normally and is fully functional.

  • POWERED_ON: power is on and the node is booting up.

  • FAILED: node is powered on but has encountered an internal failure.

  • PRESENT: node is in intermediate state in the boot sequence.

  • POWERED_OFF: power is off and the node cannot be accessed.

Software states

  • OPERATIONAL: software is operating normally and is fully functional.

  • SW_INACTIVE: software is not completely operational.

4.

Enter the show inventory command in Cisco IOS XR EXEC mode to display the details of the physical entities of NCS 1004 along with the details of QSFPs.

Example:

RP/0/RP0/CPU0:ios# show inventory
Wed Mar  4 05:10:17.107 UTC
NAME: "0/0", DESCR: "Network Convergence System 1004 Filler"
PID: NCS1K4-LC-FILLER, VID: V01, SN: N/A

NAME: "0/1", DESCR: "NCS1K4 12x QSFP28 2 Trunk C-Band DWDM card"
PID: NCS1K4-1.2T-K9, VID: V00, SN: CAT2250B0AE

NAME: "0/1-Optics0/1/0/2", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M   , VID: V03, SN: INL22262339-A

NAME: "0/1-Optics0/1/0/4", DESCR: "Cisco 100GE QSFP28 SR4 Pluggable Optics Module"
PID: QSFP-100G-SR4-S, VID: V03, SN: AVF2219S16U

NAME: "0/1-Optics0/1/0/5", DESCR: "Cisco 100G QSFP28 LR4-S Pluggable Optics Module"
PID: QSFP-100G-LR4-S, VID: V02, SN: JFQ2145701U

NAME: "0/1-Optics0/1/0/6", DESCR: "Cisco 100GE QSFP28 SR4 Pluggable Optics Module"
PID: QSFP-100G-SR4-S, VID: ES1, SN: AVF1925G012

NAME: "0/1-Optics0/1/0/7", DESCR: "Cisco 100G QSFP28 LR4-S Pluggable Optics Module"
PID: QSFP-100G-LR4-S, VID: V02, SN: JFQ2145706N

NAME: "0/1-Optics0/1/0/8", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4, VID: V01, SN: JFQ19026014

NAME: "0/1-Optics0/1/0/9", DESCR: "Cisco 100G QSFP28 LR4-S Pluggable Optics Module"
PID: QSFP-100G-LR4-S, VID: V02, SN: OPM220518HS

NAME: "0/1-Optics0/1/0/10", DESCR: "Cisco 100G QSFP28 SM-SR Pluggable Optics Module"
PID: QSFP-100G-SM-SR, VID: V02, SN: INL21490043

NAME: "0/1-Optics0/1/0/11", DESCR: "Cisco 100G QSFP28 CWDM4 Pluggable Optics Module"
PID: QSFP-100G-CWDM4-S , VID: V01, SN: JFQ211930JL

NAME: "0/1-Optics0/1/0/12", DESCR: "Cisco 100G QSFP28 CWDM4 Pluggable Optics Module"
PID: QSFP-100G-CWDM4-S, VID: V02, SN: JFQ2210801H

NAME: "0/2", DESCR: "NCS1K4 12x QSFP28 2 Trunk L-Band DWDM card"
PID: NCS1K4-1.2TL-K9   , VID: V00, SN: CAT2337B0S4

NAME: "0/2-Optics0/2/0/2", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M, VID: V03, SN: INL22262332-A

NAME: "0/2-Optics0/2/0/4", DESCR: "Cisco 100G QSFP28 SM-SR Pluggable Optics Module"
PID: QSFP-100G-SM-SR, VID: V02, SN: FNS22070HWF

NAME: "0/2-Optics0/2/0/5", DESCR: "Cisco 100G QSFP28 SM-SR Pluggable Optics Module"
PID: QSFP-100G-SM-SR, VID: V02, SN: SPT2225302D

NAME: "0/2-Optics0/2/0/6", DESCR: "Cisco 100G QSFP28 LR4-S Pluggable Optics Module"
PID: QSFP-100G-LR4-S, VID: V02, SN: FNS22310Z1X

NAME: "0/2-Optics0/2/0/8", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4, VID: V01, SN: FNS20520R8Z

NAME: "0/2-Optics0/2/0/9", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M, VID: V03, SN: INL23312282-A

NAME: "0/2-Optics0/2/0/10", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M, VID: V03, SN: INL23312282-B

NAME: "0/2-Optics0/2/0/11", DESCR: "Cisco 100G QSFP28 LR4-S Pluggable Optics Module"
PID: QSFP-100G-LR4-S, VID: V02, SN: FNS23080LKF

NAME: "0/3", DESCR: "Network Convergence System 1004 Filler"
PID: NCS1K4-LC-FILLER, VID: V01, SN: N/A

:
:
:

RP/0/RP0/CPU0:ios# show inventory
Thu May  7 11:05:13.211 UTC
NAME: "0/0", DESCR: "NCS1K4 12x QSFP28 2 Trunk C-Band DWDM card"
PID: NCS1K4-1.2T-K9    , VID: V00, SN: CAT2237B25A

NAME: "0/0-Optics0/0/0/2", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS2333080E

NAME: "0/0-Optics0/0/0/3", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS23330801

NAME: "0/0-Optics0/0/0/4", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS21140GZK

NAME: "0/0-Optics0/0/0/6", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS233209CN

NAME: "0/0-Optics0/0/0/10", DESCR: "Cisco 40GE QSFP+ LR4 Pluggable Optics Module"
PID: QSFP-40G-LR4      , VID: V02, SN: FNS23110TYD

NAME: "0/1", DESCR: "NCS1K4 4xDD,8xQSFP28,2xCFP2 DCO OTNXponder"
PID: NCS1K4-OTN-XP     , VID: V00, SN: CAT2352B007

NAME: "0/1-Optics0/1/0/0", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS2333080J

NAME: "0/1-Optics0/1/0/1", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS23330806

NAME: "0/1-Optics0/1/0/2", DESCR: "Cisco 4x10GE QSFP+ MLR Pluggable Optics Module"
PID: ONS-QSFP-4X10-MLR , VID: V01, SN: INL21010391

NAME: "0/1-Optics0/1/0/4", DESCR: "Cisco 40GE QSFP+ SR4 Pluggable Optics Module"
PID: QSFP-40G-SR4      , VID: V03, SN: JFQ20332007

NAME: "0/1-Optics0/1/0/5", DESCR: "Cisco 40GE QSFP+ SR4 Pluggable Optics Module"
PID: QSFP-40G-SR4      , VID: V03, SN: JFQ20332088

NAME: "0/1-Optics0/1/0/6", DESCR: "Cisco 4x10GE QSFP+ MLR Pluggable Optics Module"
PID: ONS-QSFP-4X10-MLR , VID: V01, SN: INL21010471

NAME: "0/1-Optics0/1/0/7", DESCR: "Cisco 4x10GE QSFP+ MLR Pluggable Optics Module"
PID: ONS-QSFP-4X10-MLR , VID: V01, SN: INL21010376

NAME: "0/2", DESCR: "NCS1K4 4xDD,8xQSFP28,2xCFP2 DCO OTNXponder"
PID: NCS1K4-OTN-XP     , VID: V00, SN: CAT2352B015

NAME: "0/2-Optics0/2/0/0", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS20360V1R

NAME: "0/2-Optics0/2/0/4", DESCR: "Cisco 40GE QSFP+ SR4 Pluggable Optics Module"
PID: QSFP-40G-SR4      , VID: V03, SN: JFQ21502017

NAME: "0/2-Optics0/2/0/5", DESCR: "Cisco 40GE QSFP+ SR4 Pluggable Optics Module"
PID: QSFP-40G-SR4      , VID: V03, SN: JFQ202120DY

NAME: "0/3", DESCR: "NCS1K4 4xDD,8xQSFP28,2xCFP2 DCO OTNXponder"
PID: NCS1K4-OTN-XP     , VID: V00, SN: CAT2352B00A

NAME: "0/3-Optics0/3/0/0", DESCR: "Cisco QSFP-100G-LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01, SN: FNS23320BS3

NAME: "0/3-Optics0/3/0/4", DESCR: "Cisco 40GE QSFP+ SR4 Pluggable Optics Module"
PID: QSFP-40G-SR4      , VID: V03, SN: AVP2217S09L

NAME: "0/3-Optics0/3/0/5", DESCR: "Cisco 40GE QSFP+ SR4 Pluggable Optics Module"
PID: QSFP-40G-SR4      , VID: V03, SN: AVP2107S0RZ

NAME: "0/RP0", DESCR: "Network Convergence System 1004 Controller"
PID: NCS1K4-CNTLR-K9   , VID: V01, SN: CAT2323B0SG
:
:
:
:
NAME: "0/PM1", DESCR: "Network Convergence System 1004 DC Power Supply Unit"
PID: NCS1K4-DC-PSU     , VID: V01, SN: POG2308CT4W