Configure Devices

This chapter describes the tasks related to device configuration in Cisco Optical Site Manager.

Figure 1. Configure Devices

Create or edit an authorization group

create, modify, or remove authorization groups, enabling you to manage user access and permissions efficiently within the network management application.

  • Create an authorization group.

  • Edit an authorization group.

Authorization groups help you manage user and group attributes used by authentication and authorization processes.

You manage authorization groups from the Devices area.

Before you begin

Log into Cisco Optical Site Manager

Follow these steps to manage authorization groups.

Procedure

Step 1

Click Devices in the left panel.

The Device Configuration page appears.

Step 2

In the Devices area, click Authorization Group to expand it.

The table lists all available authorization groups.

Step 3

Perform these steps, as needed.

To perform these steps
Create a new authorization group

  1. Click Add Auth Group.

    The Add Authorization Group dialog box appears.

  2. Enter values in the Auth Group Name, Remote User Name, and Remote Password fields.

  3. Click Add.

    The new authorization group is added to the table.
Edit an authorization group

  1. Click Edit.

    The fields in the table are now editable.

  2. Update the Remote User Name and Remote Password fields, as needed.

  3. Click Apply.

    The authorization group is updated in the table.

The authorization group table reflects your changes.

Create or edit an SNMP group

Use Cisco Optical Site Manager to manage SNMP groups so you can connect to MPBC devices. Create or edit SNMP groups as needed to enable SNMP-based communication with the MPBC devices.

SNMP groups in Cisco Optical Site Manager define access and authentication methods for MPBC devices. Each group is identified by a unique combination of group name and security level. Ensure the corresponding SNMP configuration exists on the target MPBC device before creating a group. This task allows you to

  • create an SNMP group or

  • edit an SNMP group.

Before you begin

Log into Cisco Optical Site Manager.

Ensure the SNMP configuration is set up on the MPBC device prior to managing SNMP groups.

Follow these steps to create or edit an SNMP group.

Procedure

Step 1

Click Devices in the left panel.

Step 2

In the Devices tab, click Authorization Group to expand it.

Step 3

In the SNMP section, manage SNMP groups as follows:

To Follow these instructions
Create a new SNMP group

  1. Click Add SNMP Group.

    The Add SNMP Group dialog box appears.

  2. From the Security Level drop-down list, select the desired security level (for example, auth-no-priv).

  3. Fill in the SNMP Group Name, Remote Name, Authentication Type, and Authentication Remote Password fields.

  4. Click Apply.

    The new SNMP group is added to the table.
Edit an existing SNMP group

  1. Click Edit next to the desired SNMP group.

    The fields become editable.

  2. Update the relevant fields (Remote Name, Security Level, Authentication Type, Authentication Remote Password) as needed.

  3. Click Apply.

    The changes are saved in the table.

Your changes are reflected in the SNMP group table.

Add a device

Onboard a NCS 1000 or NCS 2000 device so it can be tracked, monitored, and managed within Cisco Optical Site Manager.


Note

Wait for the current device to complete synchronization before you add the next device to Cisco Optical Site Manager.
Figure 2. Add a Device

Follow these steps to add an NCS 1000 or NCS 2000 device to Cisco Optical Site Manager.

Before you begin

Log into Cisco Optical Site Manager

Procedure

Step 1

Click Devices in the left panel.

The Device Configuration page appears.

Step 2

In the Devices tab, click the Devices section to expand it.

A table appears that lists all the devices that are configured.

Step 3

Click the Add Device icon.

The Add Device dialog box appears.

Step 4

Select the Device Type from the drop-down list.

Select

to

ncs1000

add a NCS 1000 device.

ncs2000

add a NCS 2000 device.
unmanaged-network-element

add a device that is not actively managed by NCS 1000 or NCS 2000.

Step 5

Enter the Netconf Port.

Note

 
This field is displayed only if ncs1000 is selected in the Device Type drop-down list.

Step 6

Enter the Device Name and IP Address.

Step 7

Enter the UID.

Note

 
This field is displayed only if ncs1000 or ncs2000 is selected in the Device Type drop-down list.

Step 8

Select an authorization group from the Auth Group drop-down list.

Step 9

Click Add.

The device is added to Cisco Optical Site Manager and displayed in the Devices section.

Add Unmanaged Devices

Use this task to add an unmanaged device in Cisco Optical Site Manager.

  • Allows you to add and configure passive devices on the network.

  • Supports devices that are not actively managed by NCS 1000 or NCS 2000.

Unmanaged devices are devices that are not actively managed by NCS 1000 or NCS 2000. Examples include switches, LAN controllers, and passive optical devices.

The Add Device dialog box includes the unmanaged-network-element option, which enables adding unmanaged devices.

Table 1. Feature History

Feature Name

Release Information

Description

Add Unmanaged Devices

Cisco IOS XR Release 24.3.1

The Add Device dialog box includes the unmanaged-network-element option, allowing the addition of unmanaged devices.

This enhancement allows you to add and configure passive devices on the network.

  • After adding the unmanaged device, add it to a rack unit as a passive unit.

Before you begin

Log into Cisco Optical Site Manager

Follow these steps to add an unmanaged device.

Procedure

Step 1

Click Devices in the left panel.

The Device Configuration page appears.

Step 2

In the Devices tab, click the Devices section to expand it.

The table lists all configured devices.

Step 3

Click the Add Device icon.

The Add Device dialog box appears.

Step 4

In the Add Device dialog box, perform these steps:

  1. Select unmanaged-network-element from the Device Type drop-down list.

  2. Click Add.

    The device is added to Cisco Optical Site Manager and displayed in the Devices section.

Step 5

In the rack view, perform these steps to add a passive unit:

  1. Right-click an empty rack unit and select Add a Passive Unit.

    The Add Passive Unit in Ru Position dialog box appears.

  2. Select the unmanaged device from the Select Device drop-down list.

  3. Select the passive type, slot, and passive UID from the respective drop-down lists.

  4. Click Provision.

A confirmation message appears.

Step 6

Click OK.

Step 7

After adding the unmanaged or passive device to the rack, perform these device management actions, as needed.

To Perform these steps
Delete a device

  1. Right-click the unmanaged or passive device in the rack.

  2. Select Delete.

Move a device to a different rack unit

  1. Right-click the unmanaged or passive device in the rack and select Cut.

  2. Right-click an empty rack unit and select Paste.

View device properties

  1. Right-click the unmanaged or passive device in the rack and select Properties.

The unmanaged device is added to Cisco Optical Site Manager and displayed in the Devices section.

What to do next

After adding or modifying the passive unit, verify that it is displayed correctly in the rack view and in the device list.

Add an MPBC device

Add an MPBC device to Cisco Optical Site Manager to enable effective monitoring and management of the device within your optical network.

MPBC devices are compact packet-optical platforms used with the Cisco NCS 1000 series for high-capacity optical transport deployments, enabling pluggable client signal aggregation and service interface flexibility.

The supported models are:

  • MPB-2RU-MLD-1000-1426-1454-N2-C

  • MPB-2RU-MLDS-1000-1400-1410-N2-C

  • MPB-2RU-SRP-3000-1426-1454-N2-C

Table 2. Feature History

Feature Name

Release Information

Description

Support for MPBC Raman Pump Amplifiers

Cisco IOS XR Release 26.1.1

You can now add and manage MPBC devices using the Add Device dialog box. MPBC devices are primarily used for high-power Raman amplification applications in conjunction with the NCS1010 platform.

The Optical Degrees, Internal Patch Cords, and Optical Cross Connections panels now also support MPBC devices.

Before you begin

Log into Cisco Optical Site Manager

Follow these steps to add an MPBC device.

Procedure

Step 1

Click Devices in the left panel.

Step 2

In the Devices tab, click the Devices section to expand it.

Step 3

Click the Add Device icon.

Step 4

In the Add Device dialog box, perform these steps:

  1. From the Device Type drop-down list, select MPBC.

  2. In the Device Name field, type the name of the device.

  3. Specify the IP Address and SNMP Port.

  4. From the Authorization Group drop-down list, select the SNMP group.

  5. Click Apply.

The MPBC device is added to Cisco Optical Site Manager and displayed in the Devices section.

What to do next

MPBC devices are not added to the rack by default. To add an MPBC device to the rack, follow the steps in Add a chassis.

Manage a device using IOS XR CLI

Table 3. Feature History

Feature Name

Release Information

Description

Direct CLI Access for Managed Devices

Cisco IOS XR Release 25.1.1

You can now directly access the Cisco IOS XR CLI for managed devices from the Devices section.

Cisco Optical Site Manager provides direct access to the Cisco IOS XR CLI for managed devices through the Devices section.

Figure 3. Manage a Device Using IOS XR CLI

Follow these steps to access and manage the device using the IOS XR CLI interface.

Before you begin

Log into Cisco Optical Site Manager

Procedure

Step 1

Click Devices in the left panel.

The Device Configuration page appears.

Step 2

In the Devices tab, click the Devices section to expand it.

A table appears that lists all the devices that are configured.

Step 3

Click the terminal icon next to the device under the Terminal column.

The terminal window is displayed, and the system prompts you to enter the username.

Step 4

Type the username and press Enter.

The system prompts you to enter the password.

Step 5

Type the password and press Enter.

Move a device or view device properties

Manage devices by moving them between rack units or viewing their properties in Cisco Optical Site Manager.

Before you begin

Log into Cisco Optical Site Manager

Follow these steps to move or view properties of a device.

Procedure

Step 1

Click Devices in the left panel.

Step 2

In the Devices tab, click the Devices section.

Step 3

Perform these device management actions as needed.

To Perform these steps
Move a device to a different rack unit

  1. Right-click the device in the rack and select Cut.

  2. Right-click an empty rack unit and select Paste.

View device properties

Right-click the device in the rack and select Properties.

Delete devices, SNMP group, and authorization groups

Maintain network efficiency and security by regularly deleting obsolete devices, SNMP group, and authorization groups from the application.

Follow these steps to delete devices, SNMP groups, and authorization groups:

Before you begin

Log into Cisco Optical Site Manager

Follow these steps to delete a device, SNMP group, or authorizarion group.

Procedure

Step 1

Click Devices in the left panel.

Step 2

Perform these steps as needed.

To Perform these steps
Delete a device

  1. Click the Devices section.

  2. Select the check box corresponding to the devices you want to delete.

  3. Click Delete Device(s).

  4. Confirm the action when prompted.
Delete an SNMP group

  1. Click the SNMP section.

  2. Select the check box corresponding to the SNMP group you want to delete.

  3. Click the - button to delete the SNMP group.

  4. Confirm the deletion.
Delete an authorization group

  1. Click the Username and Password section.

  2. Select the check box corresponding to the authorization groups you want to delete.

  3. Click the - button to delete the authorization group.

  4. Confirm the action.

A confirmation message appears.

Step 3

Click Yes.

The selected device, SNMP group, or autoriazrion group is removed from the system.

Retrieve device diagnostics

Retrieve, download, and review diagnostics on the Diagnostics page.

Follow these steps to retrieve and download the device diagnostics:

Before you begin

Log into Cisco Optical Site Manager

Procedure

Step 1

Click Devices in the left panel.

Step 2

In the Devices tab, click the Diagnostics section to expand it.

The configured devices are listed in a table.

Step 3

Select the Node Diagnostics check box next to the device for which you want to retrieve the diagnostics.

Step 4

Click Retrieve.

A confirmation message appears.

Step 5

Click Yes to proceed.

A Request Accepted message appears.

Step 6

Click OK.

A message appears when the diagnostic action is completed.

Step 7

Select the check box next to the device for which you want to download the diagnostics and click Download.

The system downloads a zip file containing the logs.

The downloaded ZIP file contains diagnostic logs, which can be reviewed for troubleshooting, performance monitoring, or compliance purposes.

SOCKS Proxy

Socket Secure (SOCKS) is a standard proxy protocol for IP-based applications developed by IETF. SOCKS Proxy feature allows the Cisco Optical Site Manager node to access remote NCS 2000 nodes using SOCKS Proxy server. You can set the SOCKS proxy server as an External Network Element (ENE) or a Gateway Network Element (GNE).

Benefits

  • SOCKS Proxy is used when the Cisco Optical Site Manager node cannot connect directly to the remote NCS 2000 node through DCN.

  • OSPF need not be enabled to propagate the routes as routing to the remote node is done by the SOCKS Proxy server.

  • SOCKS Proxy allows the Cisco Optical Site Manager node to connect to remote nodes behind the firewall of a GNE.

Limitations

  • A SOCKS Proxy server must be used only to connect to small remote nodes (OLA nodes).

  • A SOCKS Proxy server must serve only up to five NCS 2000 nodes.

Change the Cooling Profile Control

Use this task to change the cooling profile control of the NCS 2006 node from automatic to manual or the other way round.

Before you begin

Log into Cisco Optical Site Manager

Procedure

Step 1

Click the hamburger icon at the top-left of the page, and select Device Configuration.

Step 2

Click the Configuration > Device Settings tabs.

Step 3

Choose the control from the Cooling Profile Control drop-down list.

Step 4

Click Apply.

A confirmation message appears.

Step 5

Click Yes.

SVO-LC device onboard in R25.1.1

Each Cisco Optical Site Manager instance created in the SVO-LC supports on boarding both NCS 2000 and NCS 1000 devices. Communication with these devices is through the bridge interface (br-devices) as output interface.

SVO-LC utilizes a SOCKS server to facilitate communication with NCS 2000 devices. For NCS 1000 devices, communication is handled through a local bridge integrated into the SVO-LC, which serves as a gateway with the IP address 192.168.254.65/26. This address should be configured as the Gateway IP when adding a new route to access the NCS 1000 device.

Configure additional route for NCS 1000 device

Use this task to establish communication with the NCS 1000 device.

Before you begin

Procedure

Step 1

Click Devices in the left panel.

The Device Configuration page appears.

Step 2

Click the Networking tab.

Step 3

Click the Add Devices Gateway icon under Devices Gateway.

The Add Devices Gateway dialog box appears.

Step 4

Enter the Subnet and Gateway IP address, and click Apply.

The default Gateway IP address is 192.168.254.65

The SVO-LC establishes connection with the NCS 1000 device.
Figure 4. Add Devices Gateway