Cisco Nexus 9000 Series NX-OS Release Notes, Release 10.6(3)F

April 27, 2026

Release 10.6(3)F became available.

Ease of Use

VXLAN GPO: Intra Group Isolation and segmenting within the same host

Beginning with Cisco NX-OS Release 10.6(3)F, you can restrict communication among the endpoints within the same ESG (also known as SG) using intra-ESG isolation feature. This feature minimizes the risk of unauthorized access within ESG and enhances security posture.

For more information, refer to Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

Arp/ND qualification due to enhancement brought in as part of intra-host isolation feature

Beginning with Cisco NX-OS Release 10.6(3)F, support is added for the enhanced proxy ARP or neighbor discovery to allow packets to switch across the ports after configuring Layer 2 isolation.

For more information, refer to Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

VXLAN GPO: SGACL support for ESI multi-homing

Beginning with Cisco NX-OS Release 10.6(3)F, ESI multi homing is support in SGACL. Intra-ESG isolation and ESI multi-homing support in SGACL are mutually exclusive.

For more information, see Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

Regenerate virtual UDI  for cloned Nexus 9300v and 9500v VMs

In previous releases, cloned virtual machines (VM) retained the same virtual UDI (serial number) as the source VM, making it difficult to distinguish between instances. The enhancement provided in NX-OS Release 10.6(3)F introduces an option to regenerate the virtual UDI during cloning, ensuring each cloned VM receives a unique serial number for accurate identification and network traffic management.

For more information, refer to Cisco Nexus 9000v (9300v/9500v) Guide, Release 10.6(x).

FIPS MACSec Certification

Beginning with 10.6(3), the bootup diagnostic process is enhanced by introducing a mandatory security check for these devices:

For more information, refer to Cisco Nexus 9000 Series NX-OS System Management Configuration Guide, Release 10.6(x).

OLS SNMP support

The Optical Line System (OLS) SNMP support feature improves the existing Optical Transport Section (OTS) Management Information Base (MIB) and adds support for Optical Line System (OLS) pluggable modules. The QDD OLS pluggable integrates dual OTS controllers representing its COM and LINE ports, managing optical parameters and amplifier gains through SNMP MIBs to provide comprehensive monitoring, control, and enhanced network operation capabilities.

For more information, refer to Cisco Nexus 9000 Series Interfaces Configuration Guide, Release 10.6(x).

Feature Set

Application Select Code for transceivers following CMIS

This feature enables the host device to select the operating mode of a QDD module. It consists of codes advertised by transceivers that follow the CMIS standard.

For more information, refer to Cisco Nexus 9000 Series Interfaces Configuration Guide, Release 10.6(x).

VXLAN EVPN Resilient ECMP

Beginning with Cisco NX-OS Release 10.6(3)F, resilient ECMP hashing at the VRF level is supported for VXLAN EVPN overlays on Cisco Nexus FX2, FX3, GX, GX2, and HX platform switches.

For more information, see Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

Exclude control packets from packet truncation

Beginning with NX-OS Release 10.6(3)F, the control packets from truncation can be excluded either at the system level or at the interface level.

For more information, refer to Cisco Nexus 9000 Series System Management Configuration Guide, Release 10.6(x).

MPLS Encapsulation Statistics for SR-MPLS

Beginning with Cisco NX-OS Release 10.6(3)F, MPLS encapsulation statistics for SR-MPLS are supported on these switches:

For more information, refer to Cisco Nexus 9000 Series NX-OS Label Switching Configuration Guide, Release 10.6(x).

Licensing (SLP) Support on N9348Y12C-SE1 switches

Beginning with NX-OS Release 10.6(3)F, Smart Licensing using Policy is supported on N9348Y12C-SE1 switch.

For more information, refer to Cisco Nexus 9000 and 3000 Series NX-OS Smart Licensing Using Policy User Guide.

ND Suppression

Beginning with Cisco NX-OS Release 10.6(3)F, you can enable ND suppression feature on these switches:

For more information, see Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

Interface QoS support for QoS classification policies

Beginning with Cisco NX-OS Release 10.6(3)F, interface QoS support for QoS classification policies is provided on Cisco Nexus 9300-SE1 Series switches and N9300 Smart switches.

For more information see, Cisco Nexus 9000 Series NX-OS Quality of Service Configuration Guide, Release 10.6(x).

Support Symmetric Hashing

Beginning with Cisco NX-OS Release 10.6(3)F, support for symmetric hashing is available on Nexus 9396T12C-SE1 switches.

For more information, see Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide, Release 10.6(x).

Support IPv6 Multicast/MLD Snooping

Beginning with Cisco NX-OS Release 10.6(3)F, IPv6 Multicast routing and MLD snooping is supported on these Cisco Nexus platforms:

For more information, see Cisco Nexus 9000 Series NX-OS Multicast Routing Configuration Guide, Release 10.6(x).

Support SVI Autostate on S1 platforms

Beginning with Cisco NX-OS Release 10.6(3)F, SVI Autostate feature is supported on Cisco Nexus 9396T12C-SE1 platform switches.

For more information, see Cisco Nexus 9000 Series NX-OS Layer 2 Switching Configuration Guide, Release 10.6(x).

Static mac and Learn Disable support

Beginning with Cisco NX-OS Release 10.6(3)F, Static mac and Learn Disable Cisco Nexus 9396T12C-SE1 platform switches.

For more information, see Cisco Nexus 9000 Series NX-OS Layer 2 Switching Configuration Guide, Release 10.6(x).

QinQ Multi Tag support

Beginning with Cisco NX-OS Release 10.6(3)F, QinQ Multi Tag on all Silicon One switches.

For more information, see Cisco Nexus 9000 Series NX-OS Layer 2 Switching Configuration Guide, Release 10.6(x).

UDLD support on Cisco Nexus 9300-SE1 switches

Beginning with Cisco NX-OS Release 10.6(3)F, UDLD is supported on Cisco Nexus 9300-SE1 switches.

For more information, see Cisco Nexus 9000 Series NX-OS Layer 2 Switching Configuration Guide, Release 10.6(x).

Min-disruptive ISSU support on Nexus 9364E-SG2 switch

Beginning with NX-OS Release 10.6(3)F, minimally disruptive ISSU or min-disruptive (MD) ISSU is introduced on Nexus 9364E-SG2 Silicon One based TORs. During MD ISSU, any minimal packet disruption is displayed to the user.

For more information, refer to Cisco Nexus 9000 Series Software Upgrade and Downgrade Guide, Release 10.6(x).

TCP Keepalive for Syslog Logging

Beginning with Cisco NX-OS Release 10.6(3)F, configurable TCP keepalive idle timeout is supported for syslog TCP connections to improve reliability and prevent session drops due to idle timeouts.

For more information, refer to Cisco Nexus 9000 Series NX-OS System Management Configuration Guide, Release 10.6(x).

IPSLA/ UDP Jitter for Unnumbered Interfaces

Beginning with Cisco NX-OS Release 10.6(3)F, IP addresses for unnumbered interfaces are allocated dynamically. You can configure the interface as source for UDP Jitter and track the destination.

For more information, refer to Cisco Nexus 9000 Series Interfaces Configuration Guide, Release 10.6(x).

New HW templates for N9K-C9364C-H1

Beginning with Cisco NX-OS Release 10.6(3)F, you can use template l3-host-heavy on Cisco Nexus C9364C-H platform switches.

For more information, refer to Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 10.6(x).

vPC BGW (with IPv6 underlay)

Prior to Cisco NX-OS Release 10.6(3)F, vPC BGW supported only IPv4 underlay. Starting with Cisco NX-OS Release 10.6(3)F, vPC BGW also supports IPv6 underlay.

For more information, refer to Cisco Nexus 9000 Series NX-OS VXLAN Guide, Release 10.6(x).

IPv6 ND cache limit at the SVI

Beginning with Cisco NX-OS Release 10.6(3)F, you can configure the neighbor discovery cache limit at the SVI level. This feature improves resource optimization, security, and network performance.

For more information, see Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 10.6(x).

PIM Bidir V6 support

Beginning with Cisco NX-OS Release 10.6(3)F, support is added for PIMv6 Bidir on Cisco Nexus 9300-FX/FX2/FX3/GX/GX2/HX switches and Cisco Nexus 9700-EX/FX/GX/FX3 line cards.

For more information, refer to Cisco Nexus 9000 Series NX-OS Multicast Routing Configuration Guide, Release 10.6(x).

DLB on BGP Unnumbered Link Local IPv6 with WCMP

Beginning with Cisco NX-OS Release 10.6(3)F, you can configure DLB on BGP Unnumbered Link Local IPv6 with WCMP.

For more information, see Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 10.6(x).

Media eXchange Layer (MXL) Use for AI/ML applications in media industry

Beginning with Cisco NX-OS Release 10.6(3)F, Media Exchange Layer(MXL)traffic can co-exist along with Multicast NBM PIM Active traffic in two different VRFs.

For more information, refer to Cisco Nexus 9000 Series NX-OS IP Fabric for Media Solution Guide, Release 10.6(x).

High-Speed PID Provisioning

The feature introduces an optimized provisioning path for specific hardware identified as "high-speed PIDs". By prioritizing the Management (MGMT) interface for DHCP discovery, the device can potentially speed up the PowerOn Auto Provisioning (POAP) process.

For more information, refer to Cisco Nexus 9000 Series NX-OS Fundamentals Configuration Guide, Release 10.6(x).

SMET route for multi-site with TRM

Beginning with Cisco NX-OS Release 10.6(3)F, SMET route for multi-site with TRM is supported on all Nexus 9000 switches.

For more information, see Cisco Nexus 9000 Series NX-OS VXLAN Routing Configuration Guide, Release 10.6(x).

Undefined Policy "Permit by Default"

The new feature allows administrators to change this default action to "permit," ensuring traffic continuity while configurations are being applied or updated.

For more information, refer to Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 10.6(x).

MultiHop BFD Support for VXLAN with IPv6 Underlay

Beginning with Cisco NX-OS Release 10.6(3)F, MultiHop BFD is supported for VXLAN overlays operating over an IPv6 underlay.

For more information, refer to Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

Proportional Multipath for VNF Support for VXLAN Overlays with IPv6 Underlay

Beginning with Cisco NX-OS Release 10.6(3)F, Proportional Multipath for VNF is supported for VXLAN overlays operating over an IPv6 underlay.

For more information, refer to Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

ZR firmware upgrade support on N9K-C93600CD-GX and N9K-C9316D-GX TORs

Beginning with NX-OS Release 10.6(3)F, ZR, ZRP and Bright ZR firmware upgrade is supported on N9K-C93600CD-GX and N9K-C9316D-GX TORs.

For more information, refer to Cisco Nexus 9000 Series Interfaces Configuration Guide, Release 10.6(x).

Syslog Console Logging Performance Improvement

Beginning with Cisco NX-OS Release 10.6(3)F, syslog console logging is processed asynchronously to prevent slow or unresponsive console output from blocking syslog processing. Console-specific drop and error statistics are provided to monitor logging drop counts.

For more information, refer to Cisco Nexus 9000 Series NX-OS System Management Configuration Guide, Release 10.6(x).

Multisite Support for Private VLANs over VXLAN

Beginning with Cisco NX-OS Release 10.6(3)F, multisite support for Private VLANs over VXLAN is introduced on Cisco Nexus platform switches.

For more information, refer to Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.6(x).

ONS-QDD-OLS= support on H2R

Beginning with 10.6(3)F, N9K-C9332D-H2R is supported for Optical Line System.

For more information, refer to Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide, Release 10.6(x).

PFM-SD Multisite Support

Beginning with Cisco NX-OS Release 10.6(3)F, PIM Flooding Mechanism - Source Discovery (PFM-SD) Multisite support is introduced. This feature enables the integration of the PIM Flooding Mechanism (PFM) with the Multicast source Discovery Protocol (MSDP).

For more information, refer to:

Queuing and scheduling support on 9800 EoR line cards

Beginning with Cisco NX-OS Release 10.6(3)F, added support for Queuing and scheduling on Cisco Nexus 9800 Series switches with N9K-X9836DM-A and N9K-X98900CD-A line cards.

For more information, refer to Cisco Nexus 9000 Series NX-OS Quality of Service Configuration Guide, Release 10.6(x).

Priority flow control support on 9800 EoR line cards

Beginning with Cisco NX-OS Release 10.6(3)F, added support for Priority flow control on Cisco Nexus 9800 Series switches with N9K-X9836DM-A and N9K-X98900CD-A line cards.

For more information, refer to Cisco Nexus 9000 Series NX-OS Quality of Service Configuration Guide, Release 10.6(x).

Programmability

Configuration Candidate Session

Beginning with Release 10.6(3)F this configuration management feature allows you to stage, review, and validate configuration changes before committing them to the running configuration on Cisco Nexus 9000 Series Switches.

For more information, refer to Cisco Nexus 9000 Series NX-OS System Management Configuration Guide, Release 10.6(x).

Openconfig Model Up-Rev

Beginning with Cisco NX-OS Release 10.6(3)F, support is added to upgrade OpenConfig models to version v5.3.0.

For more information, see Cisco Nexus 9000 Series NX-OS Programmability Guide, Release 10.6(x).

Support for pushing OpenConfig + Vendor CLI config via gNMI.Set (BETA)

Beginning with Cisco NX-OS Release 10.6(3)F, gNMI Set RPC supports message type union-replace that allows a single gNMI Set RPC to carry both the CLI text configuration as well as the Openconfig YANG JSON payloads. This feature is introduced to replace the switch configuration with the union of the CLI and Openconfig.

For more information, refer to Cisco Nexus 9000 Series NX-OS Programmability Guide, Release 10.6(x).

Splunk HTTP Event Collector (HEC) Support

Beginning with 10.6(3)F, native integration between Cisco NX-OS and Splunk is enabled by allowing telemetry data to be streamed using the HTTP Event Collector (HEC) protocol.

For more information, refer to Cisco Nexus 9000 Series NX-OS Programmability Guide, Release 10.6(x).

Scalability

PTP support on N9300 Smart switches

Beginning with Cisco NX-OS Release 10.6(3)F, PTP is supported on Cisco N9324C-SE1U and N9348Y2C6D-SE1U Smart switches.

For more information, refer to:

Layer 2 support on Nexus 9800 Series EoR line cards

Beginning with Cisco NX-OS Release 10.6(3)F, Added support for Layer 2 features on Cisco Nexus 9800 Series switches with N9K-X9836DM-A and N9K-X98900CD-A line cards.

For more information, refer to:

Security

Support for 802.1X authentication mode open on MDA ports

Beginning with Cisco NX-OS Release 10.6(3)F, added support for open authentication mode to provide immediate network access for quick connectivity but still maintain security by running authentication in parallel.

For more information, refer to Cisco Nexus 9000 Series NX-OS Security Configuration Guide, Release 10.6(x).

Support command for 802.1X authentication violation restrict

Beginning with Cisco NX-OS Release 10.6(3)F, added a new command to handle security violations by creating DROP entries for violating MAC addresses instead of shutting down the port.

For more information, refer to Cisco Nexus 9000 Series NX-OS Security Configuration Guide, Release 10.6(x).

Support Change of Authorization (COA) for Voice and Data traffic

Beginning with Cisco NX-OS Release 10.6(3)F, Added support for COA to enable real-time authorization updates from ISE without client disconnection.

For more information, refer to Cisco Nexus 9000 Series NX-OS Security Configuration Guide, Release 10.6(x).

Support Dynamic ACL for Voice VLAN and Data VLAN

Beginning with Cisco NX-OS Release 10.6(3)F, Added support for DACL multi-domain mode to provide granular per-client traffic control with rules specific to each MAC address and VLAN.

For more information, refer to Cisco Nexus 9000 Series NX-OS Security Configuration Guide, Release 10.6(x).

Securing NX-OS with Live Protect enhancements

The enhancements to the Live Protect feature that secures NX-OS feature in 10.6(3)F are

For more information, refer to Cisco Nexus 9000 Series NX-OS Security Configuration Guide, Release 10.6(x).

MACsec ND ISSU

Although Nexus 9300-FX, FX2, and FX3 switches supported non-disruptive(ND) ISSU, ND ISSU was not supported on these switches when MACsec was enabled. Beginning with NX-OS Release 10.6(3)F, these switches support ND ISSU even when MACsec is enabled on their interfaces.

For more information, refer to Cisco Nexus 9000 Series Security Configuration Guide, Release 10.6(x).

CSCwe59034

Dual Active Detection Status mismatch b/w 'show vpc role' and 'show vpc internal role snmp role'

CSCwf66873

BGP Advertise-map non-exist-map will not function with match attribute statements

CSCwi76298

n9k/vsh/syslog: show run, show run inter, show logging is blocked when high rate of syslog is logged

CSCwi78803

Port w/ 10gig SFP stays down post reload in N3500-XL

CSCwp17208

Flap N9K SPAN destination port may cause forward LACP PDU to other LACP peer

CSCwq16614

N9K FX3P 1G ports with MACsec enabled drop Layer 2 (L2) traffic

CSCwq46504

"max-metric router-lsa on-startup" incorrect default config logic

CSCwq83045

Nexus 9000: Reinit Port-Channel Member Upon Receiving Unexpected flags instead of Err-Disable.

CSCwr37796

Packets drop observed during FCoE uplink PO member port update

CSCwr42548

External application should not be allowed to remove CoPP from config

CSCwr48487

Fs-daemon failures with large amount of files in bootflash

CSCwr51176

GRE traffic is dropped if it needs to cross the Peer-Link and a tunnel interface is configured on the switch

CSCwr59911

N9K/FX2/FX: AN - 100G link might take longer to come up due to repeated/failed FEC checks

CSCwr69167

N9K-C9332D-GX2B and N9K-C93180YC-FX with 4x10G CU5M :On Peer side shut/no shut , complete traffic will be lost

CSCwr69853

n9k/ptp - After GM failover or path change to current GM, MPD value might stay constant

CSCwr79751

Missing IPv6 ACL for HTTP/NTP/FTP/etc. traffic under class-management

CSCwr85409

Traffic Drop seen with multiple sak rekeys on N9396Y12C-SE1,N9336C-SE1,N9396T12C-SE1,N9348Y2C6D-SE1U,N9324C-SE1U

CSCwr86171

Nginx Crash in NX-OS 10.4

CSCwr87622

OTM Crash after reconfiguring track N9k running 10.3

CSCws02056

In Nexus NDB switches, tunnel termination with tunnel profile config + Redirect ACL leads to drops

CSCws09585

Observing no mirror packets when ERSPAN SPAN destination is a port-channel in GX and FX3 LC cards.

CSCws10107

N9K stops advertising BGP routes after flapping BGP sessions with low advertisement-interval

CSCws19374

N9K-C93108TC-FX3 speed negotiation includes unsupported 2.5/5GB speeds on Base-T ports

CSCws19451

system memory-thresholds cli does not show up on show run

CSCws24607

The EEM policy configured as a combination of event triggers does not work as expected

CSCws26199

show bgp regexp command crashes BGP process

CSCws26585

Incorrect cVpcDualActiveDetectionStatus MIB Value

CSCws26629

Eltm alarms are appearing frequently on a Nexus 9300 series switch when logging into the device

CSCws31847

Service "bloggerd" signal 11 segmentation fault

CSCws32445

VACL with MAC ACL Incorrectly Programmed in Hardware for IPv6 Underlay

CSCws33719

N9300 unexpected SG state when configured as igmp host-proxy and rcv-ing *G pim join

CSCws35761

COPP Dense profile default value is incorrectly in pps

CSCws36619

N3500-XL black-holing L2 mcast traffic in pure L2 topology

CSCws37242

DME Consistency Checker Fails for License

CSCws38283

Block FTE configurations on EX/FX chassis on N9k EOR

CSCws40028

"Match dscp tunnel" doesn't match traffic for non-IP traffic in VXLAN

CSCws42257

SSH Cipher Deny - Connection Closed

CSCws43219

TCP-AO BGP neighborship between Nexus & third-party switch fails when using crypto-algorithm hmac-sha-256

CSCws45858

IPFIB crashes when Multiple NDFC peers are upgraded at once

CSCws47647

Dynamic-Buffer-Sharing CLI Present but Non-Functional

CSCws49629

'system flash sda resize extended' fails on systems utilizing emmc flash

CSCws50158

SNMP and CLI outputs showing different values for memory utilization for Nexus running in LXC mode

CSCws50647

Openconfig interfaces/aggregate lag-speed not reflecting available port-channel bandwidth

CSCws51399

NXAPI Authorization failure with no TACACS traffic generated

CSCws52563

Inherit Port-Profile command missing post upgrade

CSCws53332

Vulnerabilities in curl 8.7.1-r0

CSCws55370

vsan_debug.log file is not truncating when using FCOE, leading to memory leak

CSCws61299

Unable to configure "icam monitor scale" in N9K-C93180YC-FX3H

CSCws61687

VXLAN traffic dropped at remote VTEP when typically reserved VLAN is used for VNI

CSCws61810

N9k: After the upgrade, the PBR becomes inactive.

CSCws66644

Sundown (FX3) Policer Deviation for Low CIR value ( <= 500Kbps)

CSCws69383

Unable to login to console after numerous failed SSH login attempts

CSCws75763

telemetry : arp process core with sys/arp/inst ephemeral sensor

CSCws80252

NX-100 : Vman core in idle state of G200 after S1 ISSU

CSCws83739

N9K-C9364C-GX ICAM LPM scale number issue

CSCws84657

NETCONF/XML broken with ISSU

CSCws90013

Executing the ex command will result in an error and will not complete successfully

CSCws92849

NETCONF L3 Configuration Push May Crash Device Agent

CSCws93840

UFDM process crash on N9K-C9348GC-FX3PH during interface flap testing

CSCwt01093

Dot1x authentication fails as Nexus sending eap-failure post ISE patch 3.3P8 and above

CSCwt01139

PBR statistics not show the stats properly

CSCwt08893

Switch doesn't re-establish BMP session after monitoring station reload.

CSCwt13956

N9K will propagate TC out from the root port when (Root Inconsistent) interface receiving the TC

CSCwt15427

L2 multicast traffic drops in IGMP setup with consistency checker failure for MET PTR in hardware and software

CSCwt21248

Nexus9800 downgrade from 10.6.3 to 10.5.x incompatibility-check doesn't detect pim-sparse on L3 PO interface

CSCwt21539

show interface brief command showing incorrect native vlan

CSCwt25882

NXOS Upgrade failure leaves Nexus stuck in bash prompt

CSCwt30826

Vlan mapping configuration stuck in ethernet port configuration

CSCwt31353

n9k/infra: infra convert log might fill logflash FS in case of binary config corruption

CSCwt31552

n9k/nfm: invalid ifindex in binary config pss

CSCwt33727

SNMP Hangs after continuous polling + stuck snmp mts buffers

CSCwt36003

tahusd crash when QSFP with 200g+ speed inserted and "no shut" on N9K type EX/FX/FX2/FX3

CSCwt36004

LLDP process is crashing continuously and generating core files.

CSCwt38794

N9K-C9516 NX-OS 10.4(4) diagmgr segfault in diagmgr_mts_send_hm_cfg during LC offline handling triggers HA policy reset / chassis reload

CSCwt39793

Anycast SVI interface IPv6 enter to TEN State after config replace or chassis reload

CSCwt40258

N9K-C93180YC-FX3 100G QSFP MACsec interface stays up despite remote shutdown/reload.

CSCwt43381

N9k BUM Encapsulation failure for Traffic from Private Vlan Host ports

CSCwt48469

MACsec in Nexus9K using 10.5(4) version is stuck in PENDING state while in Cat9K is up and SECURED

CSCwt49006

Non-ISSU ready HIFs on FEX (N9K-C93108TC-FX3P) are not properly listed when running "show lacp issu-impact"

CSCwt49540

Ingress-NAT flows leave switch without NAT for few milliseconds during OIF addition/deletion

CSCwt50336

N9k: OSPF route remains in routing table despite neighbor state being 'Init'

CSCwt50391

NX-OS: BGP process traceback/assertion failure 'tmp_com == del_com' during community deletion

CSCwt51843

Unexpected reload after upgrade due to aclqos hap reset

CSCwt52171

default interface command does not clear all VLANs from allowed list on the first execution

CSCwt57234

ECMP IPv6 Route learnt over VXLAN EVPN as Type-5 Route programmed incorrectly in FIB

CSCwt57903

switch can not process CDP packets on impacted port-channel interfaces

CSCwt59437

RPF not updated properly for PIM Bidir with phantom RP when route for RP is updated

CSCwt62258

monitor hap reset after removing SAN port-channel

CSCwt65140

C93180YC-FX3 with vlan policy-map, does not map non-ip packets with COS to qos groups on output to spine (Vxlan Fabric)

CSCwt81214

Exported flow-record Duration is negative, StartTime more than EndTime

CSCwt89636

"vn-segment xxx" added under VLAN while adding name to the VLAN in without VXLAN features enabled.

CSCwt35981

After firmware upgrade, functionality is not effective unless Explicit OIR is done

CSCvt37624

'The BGP instance is not in expected state' after quick bgp unconfig / reconfig with 700K ipv4 pfx

CSCvz63028

traditional mpls strip not working with Multicast dst-mac

CSCwh44244

DME inconsistency in sys/mplsta-[eth1/7/1] object after some CLI sequence

CSCwh88451

URIB crashed on urib_chlist_segv_handler after restarting bgp and urib together

CSCwi22304

TTL is not decremented for decap L3 VPN traffic on N9800

CSCwi24238

With NDFC/auto-config, VPC peer-link stays down on disable 'feature tunnel-encryption'

CSCwi57646

ESG_SGACL: Source of MAC detail is not seen in json output of MAC table

CSCwi87175

slight drop in L2 multicast performance in N9K-C9364C-H1 switch

CSCwi95768

Loopback Ping is not working after enabling MPLS LDP at Interface

CSCwi95977

DME CC failure for mutiisite virtual rmac

CSCwq46356

Link down during firmware activation from 71.110.17 to latest version on DP04QSDD-E25-001(ZR)

CSCwr42082

0 unicast packets  0 multicast packets  0 broadcast packets not working on N9336C-SE1 pids - N9K-C9808,N9K-C9804

CSCwr44095

On 800g optics, xcvr type is changed

CSCwr44194

Auth Mode is not "remote" for remote users post ISSU from 10.6(1) to 10.6.(2)

CSCwr50915

N9396T12C-SE1 QSFP port (97-108) with link having Copper cable does not come up as these ports does not support auto negotiation. For copper cables "no negotiate auto" needs to be configured.

CSCwr99585

NFM-RTP-SCALE: gNMIC get fails for RTP flows greater than 16K

N9K-C9808

16-RU modular switch with slots for up to 8 Line Cards in addition to 2 supervisors, 8 fabric modules, 4 fan trays, and 3 power trays.

N9K-C9804

10-RU modular switch with slots for up to 4 Line Cards in addition to 2 supervisors, 8 fabric modules, 4 fan trays, and 2 power trays.

N9K-X9836DM-A

Cisco Nexus 9800 36-port 400G QSFP-DD Line Card with MACsec.

N9K-X98900CD-A

Cisco Nexus 9800 14-port 400G QSFP-DD + 34-port 100G QSFP28 Line Card.

N9K-C9808-FM-A

Cisco Nexus 9800 Fabric Module for 8-slot Chassis

N9K-C9804-FM-A

Cisco Nexus 9800 Fabric Module for 4-slot Chassis

N9K-C9800-SUP-A

Cisco Nexus 9800 Platform Supervisor Module

N9K-C9800-SUP-B

Cisco Nexus 9800 Platform Supervisor Module

N9K-C9808-FAN-A

Cisco Nexus 9800 8-slot chassis fan tray (1^st Generation)

N9K-C9804-FAN-A

Cisco Nexus 9800 4-slot chassis fan tray (1^st Generation)

N9K-HV 6.3KW 20A-A

Cisco Nexus 9800 6,300W 20A AC and HV Power Supply

N9K-C9504

7-RU modular switch with slots for up to 4 Line Cards in addition to two supervisors, 2 system controllers, 3–6 fabric modules, 3 fan trays, and up to 4 power supplies.

N9K-C9508

13-RU modular switch with slots for up to 8 Line Cards in addition to two supervisors, 2 system controllers, 3–6 fabric modules, 3 fan trays, and up to 8 power supplies.

N9K-C9516

21-RU modular switch with slots for up to 16 Line Cards in addition to two supervisors, 2 system controllers, 3–6 fabric modules, 3 fan trays, and up to 10 power supplies.

N9K-X9716D-GX

Cisco Nexus 9500 16-port 400G QSFP-DD Line Card

4

8

N/A

N9K-X9736C-FX

Cisco Nexus 9500 36-port 40/100 Gigabit Ethernet QSFP28 Line Card

4

8

16

N9K-X9788TC-FX

Cisco Nexus 9500 48-port 1/10-G BASE-T Ethernet and 4-port 40/100 Gigabit Ethernet QSFP28 Line Card

4

8

16

N9K-X97160YC-EX

Cisco Nexus 9500 48-port 10/25-Gigabit Ethernet SFP28 and 4-port 40/100 Gigabit Ethernet QSFP28 Line Card

4

8

16

N9K-X9732C-FX

Cisco Nexus 9500 32-port 40/100 Gigabit Ethernet QSFP28 Line Card

4

8

16

N9K-X9736C-FX3

Cisco Nexus 9500 36-port 100-Gigabit Ethernet QSFP28 line card

4

8

16

N9K-X9636C-R

Cisco Nexus 9500 36-port 40/100 Gigabit Ethernet QSFP28 Line Card

4

8

N9K-X9636C-RX

Cisco Nexus 9500 36-port 40/100 Gigabit Ethernet QSFP28 Line Card

4

8

N9K-X9636Q-R

Cisco Nexus 9500 36-port 40-Gigabit Ethernet QSFP Line Card

4

8

N9K-X96136YC-R

Cisco Nexus 9500 16-port 1/10 Gigabit, 32-port 10/25 Gigabit, and 4-port 40/100 Gigabit Ethernet Line Card

4

8

N9K-X9624D-R2

Cisco Nexus 9500 24-port 400-Gigabit QDD Line Card

Not supported

8

N9K-C9504-FM-E

Cisco Nexus 9504 100-Gigabit cloud scale fabric module

4

5

N9K-C9504-FM-G

Cisco Nexus 9500 4-slot 1.6Tbps cloud scale fabric module

4

5

N9K-C9508-FM-E

Cisco Nexus 9508 100-Gigabit cloud scale fabric module

4

5

N9K-C9508-FM-E2

Cisco Nexus 9508 100-Gigabit cloud scale fabric module

4

5

N9K-C9508-FM-G

Cisco Nexus 9500 8-slot 1.6Tbps cloud-scale fabric module

4

5

N9K-C9516-FM-E2

Cisco Nexus 9516 100-Gigabit cloud scale fabric module

4

5

N9K-C9504-FM-R

Cisco Nexus 9504 100-Gigabit R-Series fabric module

4

6

N9K-C9508-FM-R

Cisco Nexus 9508 100-Gigabit R-Series fabric module

4

6

N9K-C9508-FM-R2

Cisco Nexus 9508 400-Gigabit R-Series fabric module

4

6

N9K-SUP-A

1.8-GHz supervisor module with 4 cores, 4 threads, and 16 GB of memory

2

N9K-SUP-A+

1.8-GHz supervisor module with 4 cores, 8 threads, and 16 GB of memory

2

N9K-SUP-B

2.2-GHz supervisor module with 6 cores, 12 threads, and 24 GB of memory

2

N9K-SUP-B+

1.9-GHz supervisor module with 6 cores, 12 threads, and 32 GB of memory

2

N9K-SC-A

Cisco Nexus 9500 Platform System Controller Module

2

N9K-C9504-FAN

Fan tray for 4-slot modular chassis

3

N9K-C9504-FAN2

Fan tray that supports the Cisco N9K-C9504-FM-G fabric module

3

N9K-C9508-FAN

Fan tray for 8-slot modular chassis

3

N9K-C9508-FAN2

Fan tray that supports the Cisco N9K-C9508-FM-G fabric module

3

N9K-C9516-FAN

Fan tray for 16-slot modular chassis

3

N9K-C9504-FAN-PWR

Cisco Nexus 9500 4-slot chassis 400G cloud scale fan tray power connector

1

2

N9K-C9508-FAN-PWR

Cisco Nexus 9500 4-slot chassis 400G cloud scale fan tray power connector

1

2

N9K-PAC-3000W-B

3-KW AC power supply

Up to 4

Up to 8

Up to 10

Cisco Nexus 9504

Cisco Nexus 9508

Cisco Nexus 9516

N9K-PDC-3000W-B

3-KW DC power supply

Up to 4

Up to 8

Up to 10

Cisco Nexus 9504

Cisco Nexus 9508

Cisco Nexus 9516

N9K-PUV-3000W-B

3-KW Universal AC/DC power supply

Up to 4

Up to 8

Up to 10

Cisco Nexus 9504

Cisco Nexus 9508

Cisco Nexus 9516

N9K-PUV2-3000W-B

3.15-KW Dual Input Universal AC/DC Power Supply

Up to 4

Up to 8

Up to 10

Cisco Nexus 9504

Cisco Nexus 9508

Cisco Nexus 9516

N9K-C9408

4-RU, 8-slot centralized modular chassis switch, which is configurable with up to 128 200-Gigabit QSFP56 (256 100 Gigabit by breakout) ports or 64 400-Gigabit ports.

N9K-C9400-SUP-A

Cisco Nexus 9400 Supervisor Card

N9K-C9400-SW-GX2A

Cisco Nexus 9400 25.6Tbps Switch Card

N9K-X9400-8D

Cisco Nexus 9400 8p 400G QSFP-DD LEM

N9K-X9400-16W

Cisco Nexus 9400 16p 200G QSFP56 LEM

N9K-X9400-22L

Cisco Nexus 9400 LEM with 22 10G/25G/50G ports.

N9K-C92348GC-FX3

1 RU fixed-port switch 48 10/100/1000M copper RJ-45 downlink ports, 4 10-/25G SFP28 uplink ports, and 2 40-/100G QSFP28 uplink ports.

N9K-C93400LD-H1

1-RU fixed-port, L2/L3 switch with 48 50G SFP56 ports and 4 400G QSFP-DD uplink ports.

N9K-C93108TC-FX3

1 RU fixed-port switch Forty-eight 100M/1G/10GBASE-T ports (ports 1–48), Six 40/100-Gigabit ports QSFP28 (ports 49–54), Two management ports (one 10/100/1000BASE-T port and one SFP port), One console port (RS-232), and one USB port.

N9K-C9332D-H2R

1-RU fixed-port switch with 400-Gigabit QSFP-DD ports (32), 10-Gigabit SFP+ ports (2), Management ports (one 10/100/1000BASE-T port and one SFP port), console port (RS-232), and USB port.

N9K-C9348GC-FX3

1 RU fixed-port switch 48 10/100/1000M copper RJ-45 downlink ports, 4 10-/25G SFP28 uplink ports, and 2 40-/100G QSFP28 uplink ports.

N9K-C9348GC-FX3PH

1-RU fixed-port switch 40 10M/100M/1G copper RJ-45 downlink ports that support PoE/PoE+/PoE++ and 8 10M/100M copper RJ-45 downlink ports that support PoE/PoE+/PoE++, 4 10-/25G SFP28 uplink ports, and 2 40-/100G QSFP28 uplink ports.

N9K-C93180YC-FX3H

1-RU fixed-port switch with 24 100M/1/10/25-Gigabit Ethernet SFP28 ports (ports 1–24), 6 10/25/40/50/100-Gigabit QSFP28 ports (ports 49–54), One management port (one 10/100/1000BASE-T port), and One console port (RS-232)

N9K-C9316D-GX

1-RU switch with 16x400/100/40-Gbps ports.

N9K-C9364C-GX

2-RU fixed-port switch with 64 100-Gigabit SFP28 ports.

N9K-C93600CD-GX

1-RU fixed-port switch with 28 10/40/100-Gigabit QSFP28 ports (ports 1–28), 8 10/40/100/400-Gigabit QSFP-DD ports (ports 29–36)

N9K-C9364C-H1

2-RU fixed-port switch with 64 100G SFP28 ports.

N9K-C9332D-GX2B

1-Rack-unit (1-RU) spine switch with 32p 400/100-Gbps QSFP-DD ports and 2p 1/10 SFP+ ports.

N9K-C9348D-GX2A

48p 40/100/400-Gigabit QSFP-DD ports and 2p 1/10G/10G SFP+ ports

N9K-C9364D-GX2A

64p 400/100-Gigabit QSFP-DD ports and 2p 1/10 SFP+ ports

N9K-C93180YC-FX3

48 1/10/25 Gigabit Ethernet SFP28 ports (ports 1–48)

6 10/25/40/50/100-Gigabit QSFP28 ports (ports 49–54)

N9K-C93180YC-FX3S

48 1/10/25 Gigabit Ethernet SFP28 ports (ports 1–48)

6 10/25/40/50/100-Gigabit QSFP28 ports (ports 49–54)

N9K-C9336C-FX2-E

1-RU switch with 36 40-/100-Gb QSFP28 ports

N9K-C9336C-FX2

1-RU switch with 36 40-/100-Gb Ethernet QSFP28 ports

N9K-C93360YC-FX2

2-RU switch with 96 10-/25-Gigabit SFP28 ports and 12 40/100-Gigabit QSFP28 ports

N9K-C93240YC-FX2

1.2-RU Top-of-Rack switch with 48 10-/25-Gigabit SFP28 fiber ports and 12 40-/100-Gigabit Ethernet QSFP28 ports.

N9K-C93216TC-FX2

2-RU switch with 96 100M/1G/10G RJ-45 ports, 12 40/100-Gigabit QSFP28 ports, 2 management ports (one RJ-45 and one SFP port), 1 console port, and 1 USB port.

N9K-C93180YC-FX

1-RU Top-of-Rack switch with 10-/25-/32-Gigabit Ethernet/FC ports and 6 40-/100-Gigabit QSFP28 ports. You can configure the 48 ports as 1/10/25-Gigabit Ethernet ports or as FCoE ports or as 8-/16-/32-Gigabit Fibre Channel ports.

N9K-C93180YC-FX-24

1 RU 24 1/10/25-Gigabit Ethernet SFP28 front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports. The SFP28 ports support 1-, 10-, and 25-Gigabit Ethernet connections and 8-, 16-, and 32-Gigabit Fibre Channel connections.

N9K-C93108TC-FX

1-RU Top-of-Rack switch with 48 100M/1/10GBASE-T (copper) ports and 6 40-/100-Gigabit QSFP28 ports

N9K-C93108TC-FX-24

1 RU 24 1/10GBASE-T (copper) front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports.

N9K-C93108TC-FX3P

1-RU fixed-port switch with 48 100M/1/2.5/5/10GBASE-T ports and 6 40-/100-Gigabit QSFP28 ports

N9K-C9348GC-FXP [1]

Cisco Nexus 9300 with 48p 100M/1 G, 4p 10/25 G SFP+ and 2p 100 G QSFP

NXA-SFAN-30CFM-PE

Fan module with port-side exhaust airflow (blue coloring)

3

9348GC-FX3

NXA-SFAN-30CFM-PI

Fan module with port-side intake airflow (burgundy coloring)

3

9348GC-FX3

NXA-SFAN-30CFM-PE

Fan module with port-side exhaust airflow (blue coloring)

3

9348GC-FX3PH

NXA-SFAN-30CFM-PI

Fan module with port-side intake airflow (burgundy coloring)

3

9348GC-FX3PH

NXA-SFAN-35CFM-PI

Fan module with port-side intake airflow (burgundy coloring)

6

5

4

9332D-H2R

93400LD-H1

93108TC-FX3

NXA-SFAN-35CFM-PE

Fan module with port-side exhaust airflow (blue coloring)

6

5

4

9332D-GX2B

93400LD-H1

93108TC-FX3

NXA-SFAN-35CFM-PI

Fan module with port-side intake airflow (burgundy coloring)

6

9332D-GX2B

NXA-FAN-160CFM-PE

Fan module with port-side exhaust airflow (blue coloring)

3

9364C [2]

93360YC-FX2

NXA-FAN-160CFM-PI

Fan module with port-side intake airflow (burgundy coloring)

3

9364C ^[1]

93360YC-FX2

NXA-FAN-160CFM2-PE

Fan module with port-side exhaust airflow (blue coloring)

4

9364C-GX

NXA-FAN-160CFM2-PI

Fan module with port-side intake airflow (burgundy coloring)

4

9364C-GX

NXA-FAN-30CFM-B

Fan module with port-side intake airflow (burgundy coloring)

3

93108TC-FX
93180YC-FX
9348GC-FXP

NXA-FAN-30CFM-F

Fan module with port-side exhaust airflow (blue coloring)

3

93108TC-FX
93180YC-FX
9348GC-FXP

NXA-FAN-35CFM-PE

Fan module with port-side exhaust airflow (blue coloring)

4

6

92300YC ^[1]
9332C ^[1]
93180YC-FX3S [3]
93180YC-FX3
93108TC-FX3P
93180YC-FX3H

9336C-FX2-E
9316D-GX
93600CD-GX

NXA-FAN-35CFM-PI

Fan module with port-side intake airflow (burgundy coloring)

Fan module with port-side exhaust airflow (blue coloring)

4

6

6

92300YC ^[1]
9332C ^[1]
93180YC-FX3S ^[2]
93180YC-FX3
93108TC-FX3P
93180YC-FX3H

9316D-GX
93600CD-GX

9336C-FX2-E

NXA-FAN-65CFM-PE

Fan module with port-side exhaust airflow (blue coloring)

3

93240YC-FX2 ^[1]
9336C-FX2 ^[1]

NXA-FAN-65CFM-PI

Fan module with port-side exhaust airflow (burgundy coloring)

3

93240YC-FX2
9336C-FX2 ^[1]

NXA-PDC-715W-PI

715-W DC power supply with port-side intake airflow (blue coloring)

2

93108TC-FX3P

NXA-PDC-440W-PE

440-W DC power supply with port-side exhaust airflow (blue coloring)

2

9348GC-FX3
9348GC-FX3PH

NXA-PDC-440W-PI

440-W DC power supply with port-side intake airflow (burgundy coloring)

2

9348GC-FX3

9348GC-FX3PH

NXA-PHV-350W-PE

350-W AC power supply with port-side exhaust airflow (blue coloring)

2

9348GC-FX3
9348GC-FX3PH

NXA-PHV-350W-PI

350-W AC power supply with port-side intake airflow (burgundy coloring)

2

9348GC-FX3

9348GC-FX3PH

NXA-PAC-350W-PE2

350-W AC power supply with port-side exhaust airflow (blue coloring)

2

9348GC-FX3
9348GC-FX3PH

NXA-PAC-350W-PI2

350-W AC power supply with port-side intake airflow (burgundy coloring)

2

9348GC-FX3

9348GC-FX3PH

NXA-PAC-1900W-PE

1900-W AC power supply with port-side exhaust airflow (blue coloring)

2

9348GC-FX3

9348GC-FX3PH

NXA-PAC-1900W-PI

1900-W AC power supply with port-side intake airflow (burgundy coloring)

2

9348GC-FX3

9348GC-FX3PH

NXA-PHV-2KW-PI

2000-W HVDC power supply with port-side intake airflow (burgundy coloring)

2

9332D-H2R

93400LD-H1

NXA-PAC-1500W-PE

1500-W AC power supply with port-side exhaust airflow (blue coloring)

2

9332D-GX2B

NXA-PAC-1500W-PI

1500-W AC power supply with port-side intake airflow (burgundy coloring)

2

9332D-GX2B

NXA-PAC-500W-PE

500-W AC power supply with port-side exhaust airflow (blue coloring)

2

93180YC-FX
93108TC-FX3

NXA-PAC-500W-PI

500-W AC power supply with port-side intake airflow (burgundy coloring)

2

93180YC-FX
93108TC-FX3

NXA-PAC-650W-PE

650-W AC power supply with port-side exhaust (blue coloring)

2

92300YC
93180YC-FX3S
93180YC-FX3

93180YC-FX3H

NXA-PAC-650W-PI

650-W AC power supply with port-side intake (burgundy coloring)

2

92300YC
93180YC-FX3S
93180YC-FX3

93180YC-FX3H

NXA-PAC-750W-PE

750-W AC power supply with port-side exhaust airflow (blue coloring) 1

2

9336C-FX2
9336C-FX2-E
9332C
93240YC-FX2

NXA-PAC-750W-PI

750-W AC power supply with port-side intake airflow (burgundy coloring) 1

2

9336C-FX2
9336C-FX2-E
9332C
93240YC-FX2

NXA-PAC-1100W-PE3

1100-W AC power supply with port-side exhaust airflow (blue coloring)

9316D
93240YC-FX2
93540CD-GX
9336C-FX2
9336C-FX2-E
9336C-SE1
93600CD-GX

NXA-PAC-1100W-PI3

1100-W AC power supply with port-side intake airflow (burgundy coloring)

9316D
93240YC-FX2
93540CD-GX
9336C-FX2
9336C-FX2-E
9336C-SE1
93600CD-GX

NXA-PAC-1100W-PE2

1100-W AC power supply with port-side exhaust airflow (blue coloring)

2

93240YC-FX2
9332C
9316D-GX
9336C-FX2
9336C-FX2-E
93600CD-GX

NXA-PAC-1100W-PI2

1100-W AC power supply with port-side intake airflow (burgundy coloring)

2

93240YC-FX2
9332C
9316D-GX
9336C-FX2
9336C-FX2-E
93600CD-GX

NXA-PAC-1100W-PI

Cisco Nexus 9000 PoE 1100W AC PS, port-side intake

2

93108TC-FX3P

NXA-PAC-1100W-PE

Cisco Nexus 9000 PoE 1100W AC PS, port-side exhaust

2

93108TC-FX3P

NXA-PAC-1900W-PI

Cisco Nexus 9000 PoE 1900W AC PS, port-side intake

2

93108TC-FX3P

NXA-PAC-1200W-PE

1200-W AC power supply with port-side exhaust airflow (blue coloring)

2

93360YC-FX2
9364C

NXA-PAC-1200W-PI

1200-W AC power supply with port-side intake airflow (burgundy coloring)

2

93360YC-FX2
9364C

NXA-PAC-1400W-PE

1400-W AC power supply with port-side exhaust airflow (blue coloring)

2

93400LD-H1

NXA-PAC-1400W-PI

1400-W AC power supply with port-side intake airflow (burgundy coloring)

2

93400LD-H1

N9K-PUV-1200W

1200-W Universal AC/DC power supply with bidirectional airflow (white coloring)

2

92300YC
93108TC-FX
93360YC-FX2
93180YC-FX3S
93180YC-FX
9364C
93108TC-FX3

NXA-PDC-930W-PE

930-W DC power supply with port-side exhaust airflow (blue coloring)

2

93360YC-FX2
93180YC-FX3S
93180YC-FX
9364C
93180YC-FX3H
93108TC-FX3

NXA-PDC-930W-PI

930-W DC power supply with port-side intake airflow (burgundy coloring)

2

93360YC-FX2
93180YC-FX3S
93180YC-FX
9364C
93180YC-FX3H
93108TC-FX3

NXA-PDC-1100W-PE

1100-W DC power supply with port-side exhaust airflow (blue coloring)

2

93240YC-FX2
93600CD-GX
9316D-GX
9332C
9336C-FX2
9336C-FX2-E

NXA-PDC-1100W-PI

1100-W DC power supply with port-side intake airflow (burgundy coloring)

2

93240YC-FX2
93600CD-GX
9316D-GX
9332C
9336C-FX2
9336C-FX2-E

NXA-PHV-1100W-PE

1100-W AC power supply with port-side exhaust airflow (blue coloring)

2

93240YC-FX2
9336C-FX2

NXA-PHV-1100W-PI

1100-W AC power supply with port-side intake airflow (burgundy coloring)

2

93240YC-FX2
9336C-FX2

NXA-PAC-2KW-PE

2000-W AC power supply with port-side exhaust airflow (blue coloring)

2

9364C-GX

NXA-PAC-2KW-PI

2000-W AC power supply with port-side intake airflow (burgundy coloring)

2

9364C-GX
9332D-H2R

NXA-PDC-2KW-PE

2000-W DC power supply with port-side exhaust airflow (blue coloring

2

9364C-GX

93400LD-H1

NXA-PDC-2KW-PI

2000-W DC power supply with port-side intake airflow (burgundy coloring)

2

9364C-GX

9332D-H2R

93400LD-H1

N2200-PAC-400W

400-W AC power supply with port-side exhaust airflow (blue coloring)

2

92348GC-X

N2200-PAC-400W-B

400-W AC power supply with port-side intake airflow (burgundy coloring)

2

92348GC-X

N2200-PDC-350W-B

350-W DC power supply with port-side intake airflow

2

92348GC-X

N2200-PDC-400W

400-W DC power supply with port-side exhaust airflow (blue coloring)

2

92348GC-X

N9K-X9716D-GX

4

4

No

No

No

No

N9K-X9736C-FX

5

5

5

5

5

5

N9K-X9788TC-FX

4

4

4

4

4

4

N9K-X97160YC-EX

4

4

4

4

4

4

N9K-X9732C-FX

4

5 (n+1 redundancy)

4

5 (n+1 redundancy)

4

5 (n+1 redundancy)

4

5 (n+1 redundancy)

4

5 (n+1 redundancy)

4

5 (n+1 redundancy)

N9K-X9736C-FX3

5 (n+1 redundancy)

5 (n+1 redundancy)

5 (n+1 redundancy)

5 (n+1 redundancy)

5 (n+1 redundancy)

5 (n+1 redundancy)

N9K-X9636C-RX

6

6

N9K-X9636Q-R

4

6 (n+2 redundancy)

4

6 (n+2 redundancy)

N9K-X9636C-R

5

6 (n+1 redundancy)

5

6 (n+1 redundancy)

N9K-X96136YC-R

6

6

N9K-X9624D-R2

6

nxos64-cs.<version>.bin

64-bit NX-OS core system image for most Cisco Nexus 9000 series switches

10.6(3)F

nxos64-s1.<version>.bin

64-bit NX-OS core system image for Silicon One Cisco Nexus 9000 series switches

10.6(3)F

nxos64-msll.<version>.bin

64-bit NX-OS core system image for Nexus 9000 -R and -R2 modular switches

10.6(3)F

nxos64-s1-dpu.<version>.bin

64-bit NX-OS core system image, mandatory for Cisco Nexus Smart Switches (N9324C-SE1U and N9348Y2C6D-SE1U)

10.6(3)F

nexus9300v.<version>.qcow2
nexus9300v.<version>.ova
nexus9300v.<version>.box

nexus9500v.<version>.qcow2
nexus9500v.<version>.ova
nexus9500v.<version>.box

64-bit NX-OS core system image, mandatory for Cisco Nexus 9000v Series switches

10.6(3)F

Cisco Nexus 9000 Series Switches

Cisco Nexus 9000 Series Switches documentation

Cisco NX-OS Software Strategy and Lifecycle Guide

Cisco NX-OS Software Release and Image-naming Convention

Cisco Nexus 3000 and 9000 Series NXAPI REST SDK User Guide and API Reference

Cisco Nexus 3000 and 9000 Series NX-NX-API REST SDK User Guide and API Reference

Cisco NX-OS Licensing Guide

Cisco Nexus 9000 and 3000 Series NX-OS Switch License Navigator

Cisco Nexus Smart Licensing Using Policy User Guide

Licensing Information

When you downgrade from Cisco NX-OS Release 10.6(1)F to an earlier release, the features that use the ACI+NX-OS Essentials, Advantage, and add-on licenses or the Hardware Streaming Telemetry license continue to work in honor mode in the downgraded version. In addition, the output of the show license usage command continues to include entries for these unsupported licenses.

Cisco Nexus 9000 Series NX-OS Software Upgrade and Downgrade Guide

Cisco Nexus 9000 Series Software Upgrade and Downgrade Guide

Cisco Nexus 9000 Series FPGA/EPLD Upgrade Release Notes

Cisco Nexus 9000 Series FPGA/EPLD Upgrade Release Notes

https://cisco.github.io/cisco-mibs/supportlists/nexus9000/Nexus9000MIBSupportList.html

Cisco NX-OS Supported MIBs

Cisco Nexus 9000 Series Switch FEX Support Matrix

Supported FEX modules

Cisco Nexus 9000 Series Hardware Installation Guides

Cisco Nexus 9000 Series Hardware Installation Guides