Configure Point to Point Tunneling Protocol (PPTP) Server on RV320 and RV325 VPN Router Series on Windows

Available Languages

Download Options

PDF (2.4 MB)
View with Adobe Reader on a variety of devices
ePub (2.4 MB)
View in various apps on iPhone, iPad, Android, Sony Reader, or Windows Phone
Mobi (Kindle) (933.2 KB)
View on Kindle device or Kindle app on multiple devices

Updated:December 13, 2018

Document ID:SMB4359

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Configure Point to Point Tunneling Protocol (PPTP) Server on RV320 and RV325 VPN Router Series on Windows

Objective

The Point to Point Tunneling Protocol (PPTP) is a network protocol used to create VPN tunnels between public networks. PPTP servers are also known as Virtual Private Dialup Network (VPDN) servers. PPTP is preferred over other VPN protocols because it is faster and it has the ability to work on mobile devices. A total of ten PPTP tunnels can be configured on the PPTP Server.

This article explains how to configure a PPTP (Point-to-Point Tunneling Protocol) server on Windows for the RV32x VPN Router Series.

Applicable Devices

• RV320 Dual WAN VPN Router
• RV325 Gigabit Dual WAN VPN Router

Software Version

• v1.1.0.09

Configure PPTP Server

PPTP IP Range

Step 1. Log in to the web configuration utility and choose VPN > PPTP Server. The PPTP Server page opens:

Step 2. Check the Enable check box to enable the PPTP Server on the RV320.

Step 3. Enter the starting LAN IP address of the range assigned to the first PPTP VPN client in the Range Start field. The default IP is 192.168.1.200.

Step 4. Enter the last LAN IP address of the range assigned to the last PPTP VPN client in the Range End field. The default is 192.168.1.204.

Step 5. Click Save to save the settings.

PPTP Tunnel Status

• Tunnel(s) Used — Represents the number of tunnels that are currently in use by the PPTP Server.

• Tunnel(s) Available — Represents the number of tunnels that are still available to configure the PPTP Server.

Note: You need to add users before you can setup a connection in the connection table. For more information on how to configure users, refer to to the article User and Domain Management Configuration on RV320 and RV325 VPN Router Series.

• Connection Table — The Connection List is a read-only list that shows information of VPN clients. The list shows the Username of the PPTP VPN client, Remote WAN IP address of the PPTP VPN client and the PPTP IP Address that the PPTP server assigns to the client upon connection. You need to configure PPTP VPN connection on Windows to display the user in the Connection Table.

Note: To learn more on how to setup the PPTP connection, refer to the Configure PPTP VPN Connection on Windows section.

Configure PPTP VPN Connection on Windows

Step 1. Log into the computer and choose Start > Control Panel > Network and Internet > Network and Sharing Center. The Network and Sharing Center window appears.

Step 2. Click Set up a new connection or network to create a new connection or network. The Set Up a Connection or Network window appears.

Step 3. Click Connect to a workplace to connect from the work place.

Step 4. Click Next to continue. The Connect to a Workplace window appears:

Step 5. Click Use my Internet connection (VPN) to use your Internet connection.

Step 6. Click I'll set up an Internet connection later to configure the Internet connection later.

Step 7. Enter the IP address of the LAN IP address of the RV320 into the Internet address field.

Step 8. Enter a name for the destination in the Destination name field.

Step 9. Click Create.

Note: If you are on Windows 8, the next procedure applies. If you are on Windows 7, the next three images are different, but the procedure is the same.

Step 10. Click the Network icon on the task bar. This displays all the networks, wireless, VPN, and Dial-up, available to be connected to the computer:

Step 11. Click Connect to connect the specific connection.

Note: You have to configure the user in the User Management page. To know more on how to configure user management, refer to the article User and Domain Management Configuration on RV320 Router. For the Step 12 and Step 13, you have to provide same user name and password you provided in the User Management page.

Step 12. Enter the user name in the Username field.

Step 13. Enter the password in the Password field.

Step 14. Click OK.