This document provides information and solutions for some issues that occur while navigating from System > Enterprise Parameters on Cisco Unified Communications Manager (CUCM) 7.x/8.x.
Cisco recommends that you have knowledge of these topics:
Cisco Unified Communications Manager 5.x
Cisco Unified Communications Manager 7.x
Cisco Unified Communications Manager 8.x
The information in this document is based on the Cisco Unified Communications Manager (CallManager) 5.x/7.x/8.x.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
While navigating from System > Enterprise Parameters on Cisco Unified Communications Manager (CUCM) 7.x., the error message No parameter available for this service. appears. The error message is followed by low active partition disk alerts.
This error occurs after the upgrade of Cisco Unified Communications Manager 5.x to 7.x.
Note: Cisco Unified Communications Manager 5.x provides dual partition, and an upgrade to a newer version is done from the Cisco Unified Operating System Administration web page to the inactive partition. After installing the new version, reboot the system with option switch versions and swapping inactive partition set to active.
After upgrading the CUCM cluster from 5.1.3-8000 to CUCM 7.1.3 there is an alert in the Real-Time Monitoring Tool (RTMT) that reads LowActivePartitionAvailableDiskSpace. The available disk space is at 3%.
Date: Feb 18 03:00:08 Machine Name: <Name> Severity: Critical App ID: Cisco AMC Service Message: : 88: <Date & Time> UTC : %CCM_RTMT-RTMT-2-RTMT-ERROR-ALERT: RTMT Alert Name:LowActivePartitionAvailableDiskSpace Detail: Active Partition available disk space below 4 Percent. LowActivePartitionAvailableDiskSpace partition has 2 percent of available disk space. The alert is generated on <Date & TIME> MST <Year> on node <ip address> Cluster ID: Node ID:CM1 admin:show status Host Name : <Name> Date : <Day Date Time> Time Zone : Mountain Standard Time (America/Phoenix) Locale : en_US.UTF-8 Product Ver : 22.214.171.124000-1 Platform Ver : 126.96.36.199-1 License MAC : 00145E95B357 Uptime: 09:03:21 up 12:08, 1 user, load average: 1.03, 0.74, 0.78 CPU Idle: 57.21% System: 32.34% User: 08.46% IOWAIT: 01.99% IRQ: 00.00% Soft: 00.00% Intr/sec: 1045.45 Memory Total: 2073724K Free: 30800K Used: 2042924K Cached: 329920K Shared: 0K Buffers: 38548K Total Free Used Disk/active 12317944K 271188K 11921612K (98%) Disk/inactive 12317912K 1135212K 11057556K (91%) Disk/logging 49848948K 21311604K 26005100K (55%)
Also, the service parameters and enterprise parameters web page is displaying the No parameter available for this service. error message as shown here:
The low active partition disk alert is popping up while upgrading from CUCM 5.x to 6.x or greater release because CM5.x is using static partition sizing. CUCM 6.1 and later install media use relative partition sizing which results in larger partitions.
In order to suppress the alert, which is a temporary solution, the threshold for the low active partition disk space warning should be lowered to less than 4%.
Perform these steps in order to resolve the issue:
Back up Cisco Unified Communications Manager 7.x using the Disaster Recovery System.
Perform a fresh installation using Cisco Unified Communications Manager 7.x.
Note: In order to do this, you will need to request an installation disk from your sales engineer or call the Cisco sales department.
By doing this, the disk will be reformatted and repartitioned to the new, more efficient structure.
Restore Cisco Unified Communications Manager 7.x .
The problem with the Service Parameters and Enterprise Parameters is a variant of the CSCsg09337 (registered customers only) software bug. This is known to happen during an upgrade to a new CUCM version, usually as the result of an old, corrupt device file being on the machine prior to the upgrade. CUCM 6.0 has enhanced logs to help track down the offending file in these scenarios.
Perform these steps in order to resolve the issue:
Install the proper device pack for your load.
If you have recently installed a device pack or locale on a subscriber and have lost your service parameters, either issue the run loadxml command or install the same device pack (or locale) on the publisher. This should recover the service parameters.
admin:run loadxml This command is processor intensive, and may take a few minutes to run. It should only be run on the publisher. Some services may require a restart afterwards. This is a CPU intensive command and will take a considerable amount of time to complete. Do you want to continue (y/n)? y Starting loadxml disablenotify dsn[DSN=ccm_super] disablenotify rc xml DSN=ccm_super /usr/local/cm/db/xml/xml installXml rc enablenotify dsn[DSN=ccm_super] enablenotify rc installdb Success[-x] loadxml function complete admin:
Note: If the issue is not resolved after performing these steps, open a Service Request using TAC Service Request Tool (registered customers only) , because root privilege access is needed to run the XML fix script.
CUCM 8.0 Service Parameters and Enterprise Service Parameters is blank. The failed installation of an older QED file (when a newer QED file is already installed) can cause this issue.
This error is received while trying to update a Device on the CUCM webpage:
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; InfoPath.3; Tablet PC 2.0) Timestamp: Fri, 18 Nov 2011 09:28:24 UTC
In order to resolve this problem, issue this command on the publisher:
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.