Spectrum Intelligence

Spectrum Intelligence

The Spectrum Intelligence feature scans for non-Wi-Fi radio interference on 2.4-GHz and 5-GHz bands. Spectrum intelligence provides basic functions to detect interferences of three types, namely microwave, continuous wave (like video bridge and baby monitor), wi-fi and frequency hopping (Bluetooth and frequency-hopping spread spectrum (FHSS) cordless phone).

For information about APs that support this feature see https://www.cisco.com/c/en/us/td/docs/wireless/access_point/feature-matrix/ap-feature-matrix.html.


Note

You must enable Spectrum Intelligence feature on the Cisco Aironet 1832 and 1852 series APs to get radio details, such as noise, air-quality, interference, and radio utilization on the Cisco Catalyst Center Assurance AP health.

Restrictions

  • SI APs only report a single interference type in Local mode.

  • SI does not support high availability for air quality or interference reports. High Availability is not supported because interference report/device reported will not be copied to standby after switchover. We expect AP to send it again, if at all interferer is still there.

  • Spectrum Intelligence detects only three types of devices:

    • Microwave

    • Continuous wave—(video recorder, baby monitor)

    • SI-FHSS—(Bluetooth, Frequency hopping Digital European Cordless Telecommunications (DECT) phones)

Configuring Spectrum Intelligence

Follow the procedure given below to configure spectrum intelligence:

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

ap dot11 { 24ghz | 5ghz} SI

Example:

Device(config)# ap dot11 24ghz SI

Configures the 2.4-GHz or 5-GHz Spectrum Intelligence feature on the 802.11a or 802.11b network.

Add no form of the command to disable SI on the 802.11a or 802.11b network.

Verifying Spectrum Intelligence Information

Use the following commands to verify spectrum intelligence information:

To display the SI information for a 2.4-GHz or 5-GHz band, use the following command:

Device# show ap dot11 24ghz SI config

SI Solution...................................... : Enabled
Interference Device Settings:
        SI_FHSS.................................. : Enabled
    Interference Device Types Triggering Alarms:
        SI_FHSS.................................. : Disabled

To display SI interferers of type Continuous transmitter for a 2.4-GHz band, use the following command:

Device# show ap dot11 24ghz SI device type cont_tx

DC    = Duty Cycle (%)
ISI = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID
AP type = CA, clean air, SI spectrum intelligence

No  ClusterID       DevID  Type     AP Type AP Name                 ISI  RSSI  DC   Channel
--- --------------- ------ -------- ------- ----------------- ---- ----- ----  ---  ------
   xx:xx:xx:xx  0014  BT     CA    myAP1              --   -69 00  133
   xx:xx:xx:xx  0014  BT     SI    myAP1              --   -69 00  133

To display 802.11a interference devices information for the given AP for 5-GHz, use the following command:

Device# show ap dot11 5ghz SI device type ap

DC    = Duty Cycle (%)
ISI   = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID
AP type = CA, clean air, SI spectrum intelligence

No  ClusterID/BSSID    DevID  Type    AP Type AP Name                 ISI  RSSI  DC   Channel
--- ------------------ ------ ------- ------  ------------------------ ---- ----- ---- ----------

To display all Cisco CleanAir interferers for a 2.4-GHz band, use the following command:

Device# show ap dot11 24ghz cleanair device type all

Debugging Spectrum Intelligence on Supported APs (CLI)

You need to enter these commands in the AP console. For information about APs that support this feature see https://www.cisco.com/c/en/us/td/docs/wireless/access_point/feature-matrix/ap-feature-matrix.html.

Procedure

  • Generate major Spectrum Intelligence logs for an AP by entering this command:

    debug cleanair major


  • Verify the Spectrum Intelligence scan schedule of 5 seconds on an AP by entering this command:

    debug cleanair event


  • Generate logs at 10-minute interval, when interference is not detected or reported by the AP, by entering this command:

    debug cleanair raw 10

    This command creates three files under /tmp directory from dev shell.

    • spectrum.fft

    • spectrum.dbg

    • spectrum.int


  • View the Spectrum Intelligence detected interfering devices by entering this command:

    show cleanair interferers


  • View the Spectrum Intelligence configuration status by entering this command:

    show cleanair status