Controller Self-Signed Certificate for Wireless AP Join

Use Cases

Use Case-1

Cisco Catalyst 9800-CL platform does not contain manufacturer installed SUDI certificates. You will need to configure Self-Signed Certificates on your controller.

Use Case-2

APs running on earlier versions and having Manufacturer Installed Certificate (MIC) issued by a SHA1 Cisco Trusted CA cannot join the controller with SHA2 SUDI certificate. During CAPWAP join process, the AP displays a bad certificate error and tears down the DTLS handshake.

Workaround: To upgrade APs, configure controller Self-Signed certificates. Once done, you can delete the Self-Signed certificates and revert back to the SUDI certificate.

Note

This workaround does not apply to the Embedded Wireless Controller running Catalyst 9k switches. But applies to other hardware appliance controllers, such as Cisco Catalyst 9800-40, Cisco Catalyst 9800-80, and Cisco Catalyst 9800-L.

Note

Certificate used in DTLS connections (AP and mobility) must use RSA key of size equal or more than 2048 bits. Otherwise, the APs and mobility connections will fail after reload. Run the show crypto pki certificate verbose _tp-name_ command to display the key size of the device certificate.

Prerequisites

Ensure that the VLAN interface is up and it’s IP is reachable.
Ensure that the ip http server is enabled. For more information, see Enabling HTTP Server.
Set the clock calendar-valid command appropriately. For more information, see Configuring Clock Calendar (CLI).

Check if the PKI CA server is already configured or not. If configured, you will need to delete the existing CA server configuration.

Note

The show crypto pki server command output should not display anything.

Configuring Clock Calendar (CLI)

Procedure

Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

clock calendar-valid

Example:

Device(config)# clock calendar-valid

Enables clock calendar.

Step 3

exit

Example:

Device(config)# exit

Exits configuration mode.

Enabling HTTP Server (CLI)

Procedure

	Command or Action	Purpose
Step 1	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 2	ip http server Example: `Device(config)# ip http server`	Enables the HTTP server on your IP or IPv6 system, including a Cisco web browser user interface. By default, the HTTP server uses the standard port 80.
Step 3	ip http secure-server Example: `Device(config)# ip http secure-server`	Enables the HTTP server on your IP or IPv6 system, including a Cisco web browser user interface. By default, the HTTP server uses the standard port 80.
Step 4	exit Example: `Device(config)# exit`	Exits configuration mode.

Configuring CA Server (CLI)

Procedure

Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

crypto key generate rsa general-keys modulus size_of_key_module label keypair_name

Example:

Device(config)# crypto key generate rsa general-keys modulus 2048 label WLC_CA

Configures a certificate for the controller.

When you generate RSA keys, you are prompted to enter a modulus length. A longer modulus length might be more secure, but it takes longer to generate and to use.

Note

The recommended key-pair name is WLC_CA and key modulus is 2048 bits .

Step 3

crypto pki server certificate_server_name

Example:

Device(config)# crypto pki server WLC_CA

Enables IOS certificate server.

Note

The certificate_server_name must be the same name as the keypair_name .

Step 4

issuer-name

Example:

Device(config)# issuer-name O=Cisco Virtual Wireless LAN Controller, CN=CA-vWLC

Configures X.509 distinguished name for the issuer CA certificate.

Note

You need to configure the same issuer-name as suggested for AP join.

Step 5

grant auto

Example:

Device(config)# grant auto

Grants certificate requests automatically.

Step 6

hash sha256

Example:

Device(config)# hash sha256

(Optional) Specifies the hash function for the signature used in the granted certificates.

Step 7

lifetime ca-certificate time-interval

Example:

Device(config)# lifetime ca-certificate 3650

(Optional) Specifies the lifetime in days of a CA certificate.

Step 8

lifetime certificate time-interval

Example:

Device(config)# lifetime certificate 3650

(Optional) Specifies the lifetime in days of a granted certificate.

Step 9

database archive pkcs12 password password

Example:

Device(config)# database archive pkcs12 password 0 cisco123

Sets the CA key and CA certificate archive format and password to encrypt the file.

Step 10

no shutdown

Example:

Device(config)# no shutdown

Enables the certificate server.

Note

Issue this command only after you have completely configured your certificate server.

Step 11

end

Example:

Device(config)# end

Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Configuring Trustpoint (CLI)

Procedure

Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

crypto key generate rsa exportable general-keys modulus size-of-the-key-modulus label label

Example:

Device(config)# crypto key generate rsa exportable general-keys modulus 2048 label ewlc-tp1

When you generate RSA keys, you are prompted to enter a modulus length. A longer modulus length might be more secure, but it takes longer to generate and to use.

Step 3

crypto pki trustpoint trustpoint_name

Example:

Device(config)# crypto pki trustpoint ewlc-tp1

Creates a new trust point for an external CA server. Here, trustpoint_name refers to the trustpoint name.

Note

Ensure that same names are used for key-pair (label ) and trustpoint_name .

Step 4

rsakeypair RSA_key key_size

Example:

Device(ca-trustpoint)# rsakeypair ewlc-tp1

Maps RSA key with that of the trustpoint.

RSA_key—Refers to the RSA key pair label.
key_size—Refers to the signature key length. The value ranges from 360 to 4096.

Step 5

subject-name subject_name

Example:

Device(ca-trustpoint)# subject-name O=Cisco Virtual Wireless LAN Controller, CN=DEVICE-vWLC

Creates subject name parameters for the trustpoint.

Step 6

revocation-check none

Example:

Device(ca-trustpoint)# revocation-check none

Checks revocation.

Step 7

hash sha256

Example:

Device(ca-trustpoint)# hash sha256

Specifies the hash algorithm.

Step 8

serial-number

Example:

Device(ca-trustpoint)# serial-number

Specifies the serial number.

Step 9

eku request server-auth client-auth

Example:

Device(ca-trustpoint)# eku request server-auth client-auth

(Optional) Sets certificate key-usage purpose.

Step 10

password password

Example:

Device(config)# password 0 cisco123

Enables password.

Step 11

enrollment url url

Example:

Device(config)# enrollment url http://<management-IPv4>:80

Enrolls the URL.

Note

Replace the dummy IP with management VLAN interface IP of the controller where CA server is configured.

Step 12

exit

Example:

Device(config)# exit

Exits the configuration.

Authenticating and Enrolling the PKI TrustPoint with CA Server (CLI)

Procedure

	Command or Action	Purpose
Step 1	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 2	crypto pki authenticate `trustpoint_name` Example: `Device(config)# crypto pki authenticate ewlc-tp1 Certificate has the following attributes: Fingerprint MD5: 64C5FC9A C581D827 C25FC3CF 1A7F42AC Fingerprint SHA1: 6FAFF812 7C552783 6A8FB566 52D95849 CC2FC050 % Do you accept this certificate? [yes/no]: yes Trustpoint CA certificate accepted.`	Fetches the CA certificate.
Step 3	crypto pki enroll `trustpoint_name` Example: `Device(config)# crypto pki enroll ewlc-tp1 Enter following answers for UI interaction: % Include an IP address in the subject name? [no]: no Request certificate from CA? [yes/no]: yes`	Enrolls for client certificate.
Step 4	end Example: `Device(config)# end`	Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Tagging Wireless Management TrustPoint Name (CLI)

Procedure

Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

wireless management trustpoint trustpoint_name

Example:

Device(config)# wireless management trustpoint ewlc-tp1

Tags the wireless management trustpoint name.

Step 3

end

Example:

Device(config)# end

Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Verifying Controller Certificates for Wireless AP Join

To view the CA server details, use the following command:


Device# show crypto pki server
Certificate Server WLC_CA:
Status: enabled
State: enabled
Server's configuration is locked (enter "shut" to unlock it)
Issuer name: O=Cisco Virtual Wireless LAN Controller, CN=CA-vWLC
CA cert fingerprint: 79A3DBD5 59A7E384 73ABD152 C133F4E2
Granting mode is: auto
Last certificate issued serial number (hex): 1
CA certificate expiration timer: 12:04:00 UTC Mar 8 2029
CRL NextUpdate timer: 18:04:00 UTC Mar 11 2019
Current primary storage dir: nvram:
Database Level: Minimum - no cert data written to storage

To view the trustpoint details, use the following command:


Device# show crypto pki trustpoint ewlc-tp1 status
Trustpoint ewlc-tp1:
...
State:
Keys generated ............. Yes (General Purpose, exportable)
Issuing CA authenticated ....... Yes
Certificate request(s) ..... Yes

To view the wireless management trustpoint details, use the following command:


Device# do show wireless management trustpoint
Trustpoint Name : ewlc-tp1
Certificate Info : Available
Certificate Type : SSC
Certificate Hash : 4a5d777c5b2071c17faef376febc08398702184e
Private key Info : Available
FIPS suitability : Not Applicable

To view the HTTP server status, use the following command:


Device# show ip http server status | include server status
HTTP server status: Enabled
HTTP secure server status: Enabled

Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Bengaluru 17.4.x

Bias-Free Language

Results

Chapter: Controller Self-Signed Certificate for Wireless AP Join

Controller Self-Signed Certificate for Wireless AP Join

Use Cases

Use Case-1

Use Case-2

Prerequisites

Configuring Clock Calendar (CLI)

Procedure

Example:

Example:

Example:

Enabling HTTP Server (CLI)

Procedure

Example:

Example:

Example:

Example:

Configuring CA Server (CLI)

Procedure

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Configuring Trustpoint (CLI)

Procedure

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Authenticating and Enrolling the PKI TrustPoint with CA Server (CLI)

Procedure

Example:

Example:

Example:

Example:

Tagging Wireless Management TrustPoint Name (CLI)

Procedure

Example:

Example:

Example:

Verifying Controller Certificates for Wireless AP Join

Was this Document Helpful?

Contact Cisco