Declarations of conformity and regulatory information

This section provides declarations of conformity and regulatory information for the Cisco Wireless 9174E Wi-Fi 7 Access Point. You can find additional information at: https://www.cisco.com/c/dam/assets/prod/wireless/wireless-compliance-tool/index.html.

Manufacturers Federal Communication Commission declaration of conformity statement



Access Point model

Certification number

CW9174E

UDX-600218020

Manufacturer:

Cisco Systems, Inc.170 West Tasman Drive San Jose, CA 95134-1706 USA

This device complies with Part 15 rules. Operation is subject to the following conditions:

  1. This device may not cause harmful interference.

  2. This device must accept any interference received, including interference that may cause undesired operation.

  3. Authorized 6 GHz operating conditions (FCC)

    Under the Federal Communications (FCC) authorization, installation of the CW9174E, whether within a weatherized enclosure or without and enclosure, does not modify or extend the authorized operating conditions defined by the applicable FCC grant.

    For 6 GHz operation under FCC rules, this device operates as a Low Power Indoor (LPI) access point and is restricted to indoor use only.

  4. Installation considerations (FCC)

    For FCC installations, 6 GHz operation remains permitted only where explicitly authorized under the applicable FCC regulatory certification and installation conditions, including any AFC coordination requirements for Standard Power operation.

    Any 6 GHz operation outside the scope of the FCC-certified authorization is not permitted.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna

  • Increase separation between the equipment and receiver

  • Connect the equipment to an outlet on a circuit different from which the receiver is connected

  • Consult the dealer or an experienced radio/TV technician

  • Professional Installation is recommended


Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to these two conditions:

  • This device may not cause harmful interference, and

  • This device must accept any interference received, including interference that may cause undesired operation.

This device and the antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

For products available in the USA/Canada market, 2.4 GHz operation is limited to channels 1-11.

The operation of this device is prohibited on oil platforms, cars, trains, boats and aircraft.

Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communication with unmanned aircraft systems.

VCCI statement for Japan

Warning

Warning

 

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.



Warning

 


Access Point model:

CW9174E

Guidelines for operating Cisco Wireless Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco Wireless Access Points in Japan. These guidelines are provided in both Japanese and English.

この機器の使用周波数帯では、電子レンジ等の産業・科学・医療用機器のほかエ場の製造ライン等で使用されている移動体識別用の構内無線局（免許を要する無線局）及び特定小電力無線局（免許を要しない無線局）が運用されています。

  1. この機器を使用する前に、近くで移動体臓別用の構内無線局及び特定小電力無線局が運用されていないことを確認して下さい。

  2. 万一、この機器から移動体識別用の構内無線局に対して電波干渉の事例が発生した場合には、速やかに使用周波数を変更するか又は電波の発射を停止した上、下記連絡先にご連絡頂き、混信回避のための処置等（例えぱ、ノくーティションの設置など｝Iこついてご相談して下さい。

  3. その他、この機器から移動体撒別用の特定，ト電力無線局に対して電波干渉の事例が発生した場合など何かお困りのことが起きたときは、次の連絡先へお問い合わせ下さい。

    連絡先：03-6434-6500

English Translation

This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.

  1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.

  2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.

  3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.

    Contact Number: 03-6434-6500

Statement 371—Power Cable and AC Adapter



English Translation

When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products.

Canadian compliance statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  • This device may not cause interference.

  • This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

  • L’appareil ne doit pas produire de brouillage.

  • L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Wi-Fi 7 Device

  • Devices shall not be used for control of or communications with unmanned aircraft systems.

  • Devices shall not be used on oil platforms.

  • Devices shall not be used on automobiles.

  • Devices shall not be used on trains.

  • Devices shall not be used on maritime vessels.

appareil Wi-Fi 7

  • Les dispositifs ne doivent pas être utilisés pour commander des systèmes d’aéronef sans pilote ni pour communiquer avec de tels systèmes.

  • Les dispositifs ne doivent pas être utilisés sur les plateformes de forage pétrolier.

  • Les dispositifs ne doivent pas être utilisés dans les automobiles.

  • Les dispositifs ne doivent pas être utilisés dans les trains.

  • Les dispositifs ne doivent pas être utilisés sur les navires maritimes.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

The transmitter module may not be co-located with any other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.

This radio transmitter [IC: 6961A-600218020] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Le présent émetteur radio [IC: 6961A-600218020] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur.

Antenna Type

Model Number

Antenna Gain(dBi)

Remark

Directional Array

AIR-ANT2513P4M-N

13

For 2.4G

Directional Array

AIR-ANT2513P4M-N

13

For 5G

Directional Patch

C-ANT9103

6

For 6G

Narrow Patch

MA-ANT-3-F6

11.2

For BT & IEEE 802.15.4

Standard power access points

  • The antenna height shall be determined by the installer or operator of the standard-power access point or fixed client device, or by automatic means. This information shall be stored internally in the device. Provision of accurate device information is mandatory.

  • Information for antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the EIRP elevation mask requirement set forth in section 4.5.4 (c) shall be clearly indicated.

  • La hauteur de l'antenne doit être déterminée par l'installateur ou l'opérateur du point d'accès de puissance normale ou du dispositif client fixe, ou par des dispositifs automatiques. Cette information doit être enregistrée dans le dispositif. La fourniture d'information précise sur le dispositif est obligatoire.

  • Le ou les types d'antennes, le ou les modèles d'antennes et le ou les pires angles d'inclinaison nécessaires pour rester conforme à l'exigence de la section 4.5.4 c. s'appliquant au masque de p.i.r.e. doivent être clairement indiqués.

Industry Canada

Access Point model

Certification number

CW9174E

6961A-600218020

Note

For operation in the 5925–7125 MHz band, this device is certified in Canada as a Standard Power access point under Innovation, Science and Economic Development Canada (ISED) RSS-248, and supports operation subject to Automated Frequency Coordination (AFC) requirements, where authorized. Operation must remain within the scope of the applicable ISED certification and AFC authorization.

Standard Power authorization and AFC capability do not imply approval for outdoor installation. The CW9174E is classified and documented as an indoor access point, and installation must comply with the product’s environmental design and applicable regulatory requirements.

European community, Switzerland, Norway, Iceland, and Liechtenstein compliance

The product carries the CE Mark:



The device is restricted to indoor use only when operating between 5150 MHz and 5350 MHz frequency range.

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body.


Note
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.

Access Point model:

CW9174E

Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

United Kingdom compliance

The device is restricted to indoor use only when operating between 5150 MHz and 5350 MHz frequency range. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body.

Access Point model:

CW9174E

Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

Administrative rules for Cisco Wireless Access Points in Taiwan

This section provides administrative rules for operating Cisco Wireless Access Points in Taiwan. The rules for all access points are provided in both Simplified Chinese and English.

Simplified Chinese translation

【低功率射頻器材技術規範】取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。應避免影響附近雷達系統之操作。

【本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者】

English translation

Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Management Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.

The operations near the radar system shall not be influenced.

This section contains special information for operation of Cisco Wireless Access Points in Taiwan.

Access point model

Certification number

CW9174E

TBD

Operation of Cisco Wireless Access Points in Brazil

Figure 1. Brazil Regulatory Information

This section contains special information for operation of Cisco Wireless Access Points in Brazil.

Portuguese

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.

English

This equipment is not entitled to the protection from harmful interference and may not cause interference with duly authorized systems.

equipamento Wi-Fi 7

O uso deste equipamento é restrito a ambientes fechados e proibido em plataformas petrolíferas, carros, trens, embarcações e no interior de aeronaves abaixo de 3.048 m (10.000 pés).

Wi-Fi 7 Device

Indoor use only. Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft.

Access Point model

Certification number

CW9174E

TBD

Declaration of conformity for RF exposure

This section contains information on compliance with guidelines related to RF exposure.

Generic discussion on RF exposure

The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies:

  • US 47 Code of Federal Regulations Part 2 Subpart J

  • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (99)

  • International Commission on Non Ionizing Radiation Protection (ICNIRP) 98

  • Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz

  • Australia Radiation Protection Standard


Note

The 2.4 GHz output power has been lowered for U.S and Canada regulatory domains, for channels one to four, channel 10 and 11.

To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories.

This device meets international guidelines for exposure to radio waves

The CW9174E device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health.

As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

Separation Distance

20 cm (7.87 inches)

The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended.

This device meets FCC guidelines for exposure to radio waves

The CW9174E device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health.

As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

The device has been tested and found compliant with the applicable regulations as part of the radio certification process.

Separation Distance

66 cm (25.98 inches)

The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended or lowering the transmitter power output.

This device meets the industry Canada guidelines for exposure to radio waves

The CW9174E device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health.

As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance with the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

Table 1. Separation Distance

Frequency

Distance

2.4 GHz

38 cm (14.96 inches)

5 GHz

6 GHz

Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output.

Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences radioélectriques

Cet appareil de la gamme CW9174E comprend un émetteur-récepteur radio. Il a été conçu de manière à respecter les limites en matière d'exposition aux fréquences radioélectriques (champs électromagnétiques de fréquence radio), recommandées dans le code de sécurité 6 de Santé Canada. Ces directives intègrent une marge de sécurité importante destinée à assurer la sécurité de tous, indépendamment de l'âge et de la santé.

Par conséquent, les systèmes sont conçus pour être exploités en évitant que l'utilisateur n'entre en contact avec les antennes. Il est recommandé de poser le système là où les antennes sont à une distance minimale telle que précisée par l'utilisateur conformément aux directives réglementaires qui sont conçues pour réduire l'exposition générale de l'utilisateur ou de l'opérateur.

Table 2. Distance d'éloignement

Fréquence

Distance

2.4 GHz

38 cm (14.96 inches)

5 GHz

6 GHz

Santé Canada affirme que la littérature scientifique actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l'utilisation d'un appareil sans fil. Si vous voulez réduire votre exposition encore davantage, selon l'agence, vous pouvez facilement le faire en réorientant les antennes afin qu'elles soient dirigées à l'écart de l'utilisateur, en les plaçant à une distance d'éloignement supérieure à celle recommandée ou en réduisant la puissance de sortie de l'émetteur.

Additional information on RF exposure

You can find additional information on the subject at the following links:

You can obtain additional information from the following organizations:

Declaration of conformity statements

All the Declaration of Conformity statements related to this product can be found at the following location: https://pas.cisco.com/pdtcnc/#/