Supported Hardware
These sections describe the hardware supported in Release 12.2(33)SXH and later releases:
Note ● Enter the show power command to display current system power usage.
- Flash Memory Device Summary
– bootflash: on the RP of all supervisor engines.
– sup-bootdisk: on the SP of these supervisor engines:
Supervisor Engine 720-10GE.
Supervisor Engine 720 with a CompactFlash adapter and CompactFlash card sold by Cisco Systems, Inc., for use in Supervisor Engine 720-10GE.
Supervisor Engine 32.
– sup-bootflash: on the SP of these supervisor engines:
Supervisor Engine 720 without a CompactFlash adapter and CompactFlash card sold by Cisco Systems, Inc., for use in Supervisor Engine 720.
ME 6500.
– disk0: on these supervisor engines:
Supervisor Engine 720-10GE.
Supervisor Engine 720.
Supervisor Engine 32.
ME 6500.
– disk1: on a Supervisor Engine 720.
Supervisor Engine 720-10GE (CAT6000-VS-S720-10G/MSFC3)
Supervisor Engine 720-10GE Common Features
– Internal 1-GB CompactFlash card (sup-bootdisk:).
– 1-GB DRAM.
– Internal 64-MB bootflash.
– 1-GB DRAM.
– Policy Feature Card 3CXL (PFC3CXL).
– Policy Feature Card 3C (PFC3C).
– See the “Policy Feature Cards” section.
- Integrated 720-Gbps Switch Fabric.
- One external slot:
– disk0:
– For CompactFlash Type II flash PC cards sold by Cisco Systems, Inc., for use in Supervisor Engine 720-10GE.
- Console port—EIA/TIA-232 (RS-232) port.
- Ports 1 and 2:
– QoS architecture: 2q4t / 1p3q4t
– Support for Gigabit Ethernet SFP Modules
– 10/100/1000 Mbps RJ-45
– QoS architecture: 2q4t / 1p3q4t
– Support for 10-Gigabit Ethernet X2 tranceivers
– QoS architecture: 2q4t / 1p3q4t or 8q4t / 1p7q4t
Note The 1-Gigabit Ethernet ports and the 10-Gigabit Ethernet ports have the same QoS port architecture (2q4t/1p3q4t) unless you disable the 1-Gigabit Ethernet ports with the mls qos 10g-only global configuration command, which is required to configure DSCP-based queueing. With the 1-Gigabit Ethernet ports disabled, the QoS port architecture of the 10-Gigabit Ethernet ports is 8q4t/1p7q4t.
- One port group: ports 1 through 5.
- Two Universal Serial Bus (USB) 2.0 ports (not currently enabled)
Supervisor Engine 720-10GE with PFC3C and PFC3CXL
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Supervisor Engine 720-10GE with PFC3CXL |
12.2(33)SXH
|
|
Supervisor Engine 720-10GE with PFC3C |
12.2(33)SXH
1 |
Supervisor Engine 720-10GE Restrictions
- In RPR redundancy mode, the ports on a Supervisor Engine 720-10GE in standby mode are disabled.
- Supervisor Engine 720-10GE requires a high-capacity fan tray (see the “Fan Trays” section). All E-series chassis have a high-capacity fan tray.
- There are no memory-only upgrade options for the Supervisor Engine 720-10GE.
Supervisor Engine 720 (CAT6000-SUP720/MSFC3)
Supervisor Engine 720 Common Features
– As an upgrade, WS-CF-UPG=
– See this publication:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_17277.html
- Two external slots (disk0: and disk1:) for CompactFlash Type II flash PC cards sold by Cisco Systems, Inc., for use in Supervisor Engine 720.
Note Some Supervisor Engine 720 Release 12.2SX images are larger than the bootflash device and must be stored on a CompactFlash card (sup-bootdisk: or disk0: or disk1:).
- Two Ethernet uplink ports:
– 512-KB packet buffer per port
– Port 1—Gigabit Interface Converter (GBIC)
– Port 2—Configurable as either:
• Gigabit Interface Converter (GBIC)
• 10/100/1000 Mbps RJ-45
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Port grouping:
– Number of ports: 2
– Number of port groups: 1
– Port ranges per port group: 1–2
- Supervisor Engine 720 requires a high-capacity fan tray (see the “Fan Trays” section). All E-series chassis have a high-capacity fan tray.
Supervisor Engine 32 (CAT6000-SUP32/MSFC2A)
Supervisor Engine 32 Restrictions
- Supervisor Engine 32 requires a high-capacity fan tray (see the “Fan Trays” section). All E-series chassis have a high-capacity fan tray.
- In some chassis, Supervisor Engine 32 requires a high-capacity power supply (see the “Power Supplies” section).
- Supervisor Engine 32 cannot support this hardware:
– DFCs (switching modules with DFCs do not power up with a Supervisor Engine 32)
– WS-X6700 series switching modules
– WS-X6816-GBIC switching modules
– The WS-SVC-WISM-1-K9 Wireless Services Module (WiSM)
– 7600-SIP-600 SPA Interface Processor-600 and SPAs supported only in 7600-SIP-600.
- Supervisor Engine 32 does not support this hardware:
– WS-F6K-PFC3A Policy Feature Card 3A (PFC3A)
– WS-F6K-PFC3BXL Policy Feature Card 3BXL (PFC3BXL)
– CISCO7603 3-slot chassis
- Supervisor Engine 32 cannot support these software features and commands:
– Egress multicast replication
– Multicast replication mode detection
– All fabric configuration commands
Supervisor Engine 32 Features
Note ● See this publication for Supervisor Engine 32 hardware information:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Module_Installation/Sup_Eng_Guide/supe_gd.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-SUP32-10GE-3B
WS-SUP32-GE-3B
|
Supervisor Engine 32:
- One 10/100/1000 Mbps RJ-45 port
- WS-SUP32-10GE
– Two 10-Gigabit Ethernet ports – Requires XENPAKs
– Eight SFP ports – Requires Gigabit or 10/100/1000 Mbps Ethernet SFPs
- QoS port architecture (Rx/Tx): 2q8t/1p3q8t
- One external slot (disk0:) for CompactFlash Type II flash PC cards sold by Cisco Systems, Inc., for use in Supervisor Engine 32
- Switch processor
– Internal 256 MB CompactFlash card (sup-bootdisk:) – 512-MB or more DRAM (some images require more DRAM)
– Internal 64-MB bootflash – 512-MB or more DRAM (some images require more DRAM)
|
12.2(18)SXF
|
Cisco ME 6500 Series Ethernet Switches (ME6524)
Product ID
(append “=” for spares)
|
|
|
|
Cisco ME 6500 Series Ethernet switches:
– 256-MB DRAM – 128-MB bootflash
- Policy Feature Card 3C (PFC3C):
– Supports a theoretical maximum of 96 K MAC addresses (64 K MAC addresses recommended maximum). – The PFC3C operates in PFC3C mode. Enter the show platform hardware pfc mode command to display the PFC3 mode.
- Route processor (RP)—Multilayer Switch Feature Card 2A (MSFC2A):
– 512-MB DRAM – 64-MB bootflash
- Fan tray: FAN-C6524
- Power supplies: PWR-400W-DC
- 64 chassis MAC addresses
- Eight Gigabit Ethernet SFP ports:
– Requires Gigabit Ethernet SFPs – 1 port group: ports 25–32 – QoS port architecture (Rx/Tx): 2q8t/1p3q8t
– 24 Gigabit Ethernet SFP ports (requires Gigabit Ethernet SFPs) – 4 port groups: ports 1–6, 7–12, 13–18, 19–24 – QoS port architecture (Rx/Tx): 1q2t/1p3q8t
– 24 10/100/1000 Mbps RJ-45 Ethernet ports – 4 port groups: ports 1–6, 7–12, 13–18, 19–24 – QoS port architecture (Rx/Tx): 1q2t/1p3q8t |
12.2(33)SXH Not supported in 12.2(33)SXJ and later releases. |
|
|
Note See this publication for Cisco ME 6500 Series Ethernet switch hardware information: http://www.cisco.com/en/US/products/ps6845/prod_installation_guides_list.html |
Policy Feature Card Guidelines and Restrictions
- The PFC3C supports a theoretical maximum of 96 K MAC addresses (64 K MAC addresses recommended maximum).
- The PFC3A, PFC3B, and PFC3BXL support a theoretical maximum of 64 K MAC addresses (32 K MAC addresses recommended maximum).
- The PFC3 partitions the hardware FIB table to route IPv4 unicast, IPv4 multicast, MPLS, and IPv6 unicast and multicast traffic in hardware. Traffic for routes that do not have entries in the hardware FIB table are processed by the route processor in software.
The defaults for XL mode are:
– IPv4 unicast and MPLS—512,000 routes
– IPv4 multicast and IPv6 unicast and multicast—256,000 routes
The defaults for Non-XL mode are:
– IPv4 unicast and MPLS—192,000 routes
– IPv4 multicast and IPv6 unicast and multicast—32,000 routes
Note The size of the global internet routing table plus any local routes might exceed the non-XL mode default partition sizes.
These are the theoretical maximum numbers of routes for the supported protocols (the maximums are not supported simultaneously):
– XL mode :
• IPv4 and MPLS—Up to 1,007,000 routes
• IPv4 multicast and IPv6 unicast and multicast—Up to 503,000 routes
– Non-XL mode :
• IPv4 and MPLS—Up to 239,000 routes
• IPv4 multicast and IPv6 unicast and multicast—Up to 119,000 routes
Enter the mls cef maximum-routes command to repartition the hardware FIB table. IPv4 unicast and MPLS require one hardware FIB table entry per route. IPv4 multicast and IPv6 unicast and multicast require two hardware FIB table entries per route. Changing the partition for one protocol makes corresponding changes in the partitions of the other protocols. You must enter the reload command to put configuration changes made with the mls cef maximum-routes command into effect.
Note With a non-XL-mode system, if your requirements cannot be met by repartitioning the hardware FIB table, upgrade components as necessary to operate in XL mode.
- You cannot use one type of PFC3 on one supervisor engine and a different type on the other supervisor engine for redundancy. You must use identical policy feature cards for redundancy.
- PFC3A—These restrictions apply to a configuration with a PFC3A and these DFCs:
– PFC3A and DFC3A—No restrictions (PFC3A mode; does not support virtual switch mode).
– PFC3A and DFC3B—The PFC3A restricts DFC3B functionality: the DFC3B functions as a DFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3A and DFC3BXL—The PFC3A restricts DFC3BXL functionality: the DFC3BXL functions as a DFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3A and DFC3C—The PFC3A restricts DFC3C functionality: the DFC3C functions as a DFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3A and DFC3CXL—The PFC3A restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3A (PFC3A mode; does not support virtual switch mode).
- PFC3B—These restrictions apply to a configuration with a PFC3B and these DFCs:
– PFC3B and DFC3A—PFC3B functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3B functions as a PFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3B and DFC3B—No restrictions (PFC3B mode; does not support virtual switch mode).
– PFC3B and DFC3BXL—The PFC3B restricts DFC3BXL functionality: after a reload with a DFC3BXL-equipped module installed, the DFC3BXL functions as a DFC3B (PFC3B mode; does not support virtual switch mode).
– PFC3B and DFC3C—The PFC3B restricts DFC3C functionality: the DFC3C functions as a DFC3B (PFC3B mode; does not support virtual switch mode).
– PFC3B and DFC3CXL—The PFC3B restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3B (PFC3B mode; does not support virtual switch mode).
- PFC3BXL—These restrictions apply to a configuration with a PFC3BXL and these DFCs:
– PFC3BXL and DFC3A—PFC3BXL functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3BXL functions as a PFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3BXL and DFC3B—PFC3BXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3BXL functions as a PFC3B (PFC3B mode; does not support virtual switch mode).
– PFC3BXL and DFC3BXL—No restrictions (PFC3BXL mode; does not support virtual switch mode).
– PFC3BXL and DFC3C—Each restricts the functionality of the other: the PFC3BXL functions as a PFC3B and the DFC3C functions as a DFC3B (PFC3B mode; does not support virtual switch mode).
– PFC3BXL and DFC3CXL—The PFC3BXL restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3BXL (PFC3BXL mode; does not support virtual switch mode).
- PFC3C—These restrictions apply to a configuration with a PFC3C and these DFCs:
– PFC3C and DFC3A—PFC3C functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3C functions as a PFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3C and DFC3B—PFC3C functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3C functions as a PFC3B (PFC3B mode; does not support virtual switch mode).
– PFC3C and DFC3BXL—PFC3C functionality is restricted by the DFC3BXL: after a reload with a DFC3BXL-equipped module installed, the PFC3C functions as a PFC3BXL (PFC3BXL mode; does not support virtual switch mode).
– PFC3C and DFC3C—No restrictions (PFC3C mode).
– PFC3C and DFC3CXL—The PFC3C restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3C (PFC3C mode).
- PFC3CXL—These restrictions apply to a configuration with a PFC3CXL and these DFCs:
– PFC3CXL and DFC3A—PFC3CXL functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3CXL functions as a PFC3A (PFC3A mode; does not support virtual switch mode).
– PFC3CXL and DFC3B—PFC3CXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3CXL functions as a PFC3B (PFC3B mode; does not support virtual switch mode).
– PFC3CXL and DFC3BXL—PFC3CXL functionality is restricted by the DFC3BXL: after a reload with a DFC3BXL-equipped module installed, the PFC3CXL functions as a PFC3BXL (PFC3BXL mode; does not support virtual switch mode).
– PFC3CXL and DFC3C—PFC3CXL functionality is restricted by the DFC3C: after a reload with a DFC3C-equipped module installed, the PFC3CXL functions as a PFC3C (PFC3C mode).
– PFC3CXL and DFC3CXL—No restrictions (PFC3CXL mode).
- Switching modules that you install after bootup that are equipped with a DFC that imposes a more restricted PFC mode than the current PFC mode remain powered down.
- You must reboot to use a switching module equipped with a DFC that imposes a more restricted PFC mode than the current PFC mode.
- Enter the show platform hardware pfc mode command to display the PFC mode.
Policy Feature Card 3C
(append “=” for spares)
|
|
Minimum
Software
Versions
|
VS-F6K-PFC3C
ME-C6524-PFC3C
|
Policy Feature Card 3C (PFC3C) |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Cisco ME 6500 Series Ethernet switches |
12.2(33)SXH
|
Policy Feature Card 3A
Note WS-F6K-PFC3A is available only on WS-SUP720. It is not orderable.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Policy Feature Card 3A (PFC3A) |
Supported only with Supervisor Engine 720 |
12.2(14)SX
|
Distributed and Centralized Forwarding Cards
Note See the “Policy Feature Cards” section for Policy Feature Cards (PFC) and Distributed Forwarding Card (DFC) restrictions.
Distributed Forwarding Card 3BXL
WS-F6700-DFC3BXL
Note ● WS-F6700-DFC3BXL uses memory that is installed on the switching module.
- See this publication for information about WS-F6700-DFC3BXL upgrades:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Distributed Forwarding Card 3BXL (DFC3BXL) for use on CEF720 modules |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17d)SXB6
|
WS-F6K-DFC3BXL
Note ● See this publication for information about WS-F6K-DFC3BXL memory upgrades:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html
- Supervisor Engine 720 supports a WS-F6K-DFC3BXL on these WS-X6516-GBIC switching module hardware revisions:
– Lower than 5.0
– 5.5 and higher
- Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
- Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
- With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
- See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/en/US/ts/fn/200/fn24494.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Distributed Forwarding Card 3BXL (DFC3BXL) for use on dCEF256 and CEF256 modules |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXD3
|
Distributed Forwarding Card 3B
WS-F6700-DFC3B
Note ● WS-F6700-DFC3B uses memory that is installed on the switching module.
- See this publication for information about WS-F6700-DFC3B upgrades:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Distributed Forwarding Card 3B (DFC3B) for use on CEF720 modules |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17d)SXB6
|
WS-F6K-DFC3B
Note ● See this publication for information about WS-F6K-DFC3B memory upgrades:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html
- Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
- Supervisor Engine 720 supports a WS-F6K-DFC3B on these WS-X6516-GBIC switching module hardware revisions:
– Lower than 5.0
– 5.5 and higher
- Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
- With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
- See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/en/US/ts/fn/200/fn24494.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Distributed Forwarding Card 3B (DFC3B) for use on dCEF256 and CEF256 modules |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXD3
|
Distributed Forwarding Card 3A
WS-F6700-DFC3A
Note ● WS-F6700-DFC3A uses memory that is installed on the switching module.
- See this publication for information about WS-F6700-DFC3A memory upgrades:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Distributed Forwarding Card 3A (DFC3A) for use on CEF720 modules |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17a)SX
|
WS-F6K-DFC3A
Note ● Not supported in virtual switch mode.
- See this publication for information about WS-F6K-DFC3A memory upgrades:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html
- Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
- Supervisor Engine 720 supports a WS-F6K-DFC3A on these WS-X6516-GBIC switching module hardware revisions:
– Lower than 5.0
– 5.5 and higher
- Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
- With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
- See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/en/US/ts/fn/200/fn24494.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Distributed Forwarding Card 3A (DFC3A) for use on dCEF256 and CEF256 modules |
Supported only with Supervisor Engine 720 |
12.2(14)SX
|
Centralized Forwarding Card (WS-F6700-CFC)
Note ● There are no memory upgrade options for WS-F6700-CFC.
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Centralized Forwarding Card (CFC) for use on CEF720 modules |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17a)SX
|
10-Gigabit Ethernet Switching Modules
76-ES+XT-4TG3CXL, 76-ES+XT-4TG3C
Note ● Not supported in PFC3A mode.
- CDP is disabled by default on ES+ line card ports ( CSCtk12860).
(append “=” for spares)
|
|
Minimum
Software
Versions
|
76-ES+XT-4TG3CXL
(has DFC3CXL)
76-ES+XT-4TG3C
(has DFC3C)
|
Four-port Ethernet Services Plus Extended Transport (ES+XT) Line Card
- Four 10GE ports
- Dual fabric connections
- Network Processors (NP):
– Port 1: NP0 – Port 2: NP1 – Port 3: NP2 – Port 4: NP3
- Transceivers: LAN/WAN PHY, OTN/G.709
|
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
76-ES+XT-2TG3CXL, 76-ES+XT-2TG3C
Note ● Not supported in PFC3A mode.
- CDP is disabled by default on ES+ line card ports ( CSCtk12860).
(append “=” for spares)
|
|
Minimum
Software
Versions
|
76-ES+XT-2TG3CXL
(has DFC3CXL)
76-ES+XT-2TG3C
(has DFC3C)
|
Two-port Ethernet Services Plus Extended Transport (ES+XT) Line Card
- Two 10GE ports
- Single fabric connection
- Network Processors (NP):
– Port 1: NP0 – Port 2: NP1
- Transceivers: LAN/WAN PHY, OTN/G.709
|
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
7600-ES+4TG3CXL, 7600-ES+4TG3C
Note ● Not supported in PFC3A mode.
- CDP is disabled by default on ES+ line card ports ( CSCtk12860).
(append “=” for spares)
|
|
Minimum
Software
Versions
|
7600-ES+4TG3CXL
(has DFC3CXL)
7600-ES+4TG3C
(has DFC3C)
|
Four-port Ethernet Services Plus (ES) Line Card
- Four 10GE ports
- Dual fabric connections
- Network Processors (NP):
– Port 1: NP0 – Port 2: NP1 – Port 3: NP2 – Port 4: NP3 |
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
7600-ES+2TG3CXL, 7600-ES+2TG3C
Note ● Not supported in PFC3A mode.
- CDP is disabled by default on ES+ line card ports ( CSCtk12860).
(append “=” for spares)
|
|
Minimum
Software
Versions
|
7600-ES+2TG3CXL
(has DFC3CXL)
7600-ES+2TG3C
(has DFC3C)
|
Two-port Ethernet Services Plus (ES) Line Card
- Two 10GE ports
- Single fabric connection
- Network Processors (NP):
– Port 1: NP0 – Port 2: NP1 |
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
WS-X6716-10T 16-port 10-Gigabit Ethernet Copper Switching Module
Note ● When not configured in oversubscription mode, supported in virtual switch links with Release 12.2(33)SXI and later releases.
- The orderable product IDs are WS-X6716-10T-3C and WS-X6716-10T-3CXL.
- The front panel is labeled WS-X6716-10T.
- Cisco IOS software commands display “WS-X6716-10T” with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
- To configure WS-X6716-10T port oversubscription, use the hw-module slot command.
- In these chassis, operation of a WS-X6716-10T switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:
- WS-C6513
- CISCO7613
- WS-C6509
- OSR-7609
- WS-C6506
- CISCO7606
- Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6716-10T.
- All E-Series chassis provide NEBS compliance.
- Support in the WS-C6509-NEB-A chassis requires two FAN-MOD-09 modules.
- Not supported in the WS-C6503, CISCO7603, or WS-C6509-NEB chassis.
- In a 13-slot chassis, supported only in slots 9 through 13 and does not power up in other slots.
- Does not support ISL encapsulation.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6716-10T-3C (WS-X6716-10T with WS-F6700-DFC3C) |
16-port 10-Gigabit Ethernet copper (RJ-45) module
- dCEF720
- Supports egress multicast replication
- QoS port architecture (Rx/Tx):
– Oversubscription mode : 1p7q2t/1p7q4t – Performance mode: 8q4t/1p7q4t – Both modes support DSCP-based queueing
- Dual switch-fabric connections
Fabric Channel #1: ports 1–8 Fabric Channel #2: ports 9–16
- Number of ports: 16
Number of port groups: 4 Port ranges per port group: 1–4, 5–8, 9–12, 13–16
|
With Supervisor Engine 720-10GE |
12.2(33)SXI4 (12.2(33)SXI4a
or later recommended)
|
With Supervisor Engine 720 |
WS-X6716-10G 16-port 10-Gigabit Ethernet X2 Switching Module
Note ● The orderable product IDs are WS-X6716-10G-3C and WS-X6716-10G-3CXL.
- The front panel is labeled WS-X6716-10GE.
- Cisco IOS software commands display “WS-X6716-10G” with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
- To configure WS-X6716-10G port oversubscription, use the hw-module slot command.
- In these chassis, operation of a WS-X6716-10G switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:
– WS-C6513
– CISCO7613
– WS-C6509
– WS-C6509-NEB
– OSR-7609
– WS-C6506
– CISCO7606
Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6716-10G.
Note All E-Series chassis provide NEBS compliance.
- Support in the WS-C6509-NEB-A chassis requires two FAN-MOD-09 modules.
- WS-X6716-10G is not supported in the WS-C6503 and CISCO7603 chassis.
- In a 13-slot chassis, WS-X6716-10G is supported only in slots 9 through 13 and does not power up in other slots.
- With Release 12.2(33)SXH1, WS-X6716-10G ports in oversubscription mode do not support VACL capture. ( CSCsm46682)
- Not supported in virtual switch links with Releases earlier than Release 12.2(33)SXI.
- When not configured in oversubscription mode, supported in virtual switch links with Release 12.2(33)SXI and later releases.
- Does not support ISL encapsulation.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6716-10G-3C (WS-X6716-10G with WS-F6700-DFC3C) |
16-port 10-Gigabit Ethernet X2 module
- dCEF720
- Supports egress multicast replication
- QoS port architecture (Rx/Tx):
– Oversubscription mode : 1p7q2t/1p7q4t – Performance mode: 8q4t/1p7q4t – Both modes support DSCP-based queueing
- Dual switch-fabric connections
Fabric Channel #1: ports 1–8 Fabric Channel #2: ports 9–16
- Number of ports: 16
Number of port groups: 4 Port ranges per port group: 1–4, 5–8, 9–12, 13–16
|
With Supervisor Engine 720-10GE |
12.2(33)SXH2
|
With Supervisor Engine 720 |
12.2(33)SXH2
|
WS-X6708-10GE 8-port 10-Gigabit Ethernet X2 Switching Module
Note ● WS-X6708-10G-3C and WS-X6708-10G-3CXL are the orderable product IDs.
- The front panel is labeled WS-X6708-10GE.
- Cisco IOS software commands display WS-X6708-10GE with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
- To configure WS-X6708-10GE port oversubscription, use the hw-module oversubscription command.
- In these chassis, operation of a WS-X6708-10GE switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:
– WS-C6513
– CISCO7613
– WS-C6509
– WS-C6509-NEB
– OSR-7609
– WS-C6506
– CISCO7606
Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6708-10GE.
Note All E-Series chassis provide NEBS compliance.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6708-10G-3CXL (WS-X6708-10GE with WS-F6700-DFC3CXL) |
8-port 10-Gigabit Ethernet X2 module
- dCEF720
- Supports egress multicast replication
- QoS port architecture (Rx/Tx):
– Oversubscription mode : 1p7q2t/1p7q4t – Performance mode: 8q4t/1p7q4t – Both modes support DSCP-based queueing
- Dual switch-fabric connections
Fabric Channel #1: Ports 2, 3, 6, 8 Fabric Channel #2: Ports 1, 4, 5, 7
- Number of ports: 8
Number of port groups: 8 Port ranges per port group: 1 port in each group
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF5
|
WS-X6704-10GE 4-port 10-Gigabit Ethernet XENPAK Switching Module
Note ● WS-X6704-10GE requires one of the following:
– WS-F6700-DFC3CXL
– WS-F6700-DFC3C
– WS-F6700-DFC3BXL (not supported in virtual switch mode)
– WS-F6700-DFC3B (not supported in virtual switch mode)
– WS-F6700-DFC3A (not supported in virtual switch mode)
– WS-F6700-CFC
- WS-X6704-10GE ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
- WS-X6704-10GE is supported in the WS-C6503-E chassis.
- WS-X6704-10GE is not supported in the WS-C6503 and CISCO7603 chassis.
- In a 13-slot chassis, WS-X6704-10GE is supported only in slots 9 through 13 and does not power up in other slots.
- On WS-X6704-10GE ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6704-10GE ports that interconnect network devices.
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
- Does not support ISL encapsulation.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
4-port 10-Gigabit Ethernet XENPAK
- dCEF720 with a DFC
- CEF720 with WS-F6700-CFC
- Supports egress multicast replication
- QoS port architecture (Rx/Tx):
– With DFC3: 8q8t/1p7q8t – With CFC: 1q8t/1p7q8t
- Dual switch-fabric connections
Fabric Channel #1: Ports 3 and 4 Fabric Channel #2: Ports 1 and 2
- Number of ports: 4
Number of port groups: 4 Port ranges per port group: 1 port in each group
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 and DFC3C or DFC3CXL |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17a)SX
|
WS-X6502-10GE 1-port 10-Gigabit Ethernet Switching Module
Note ● WS-X6502-10GE does not support ISL encapsulation.
- Use with Release 12.2(33)SXH or later and a DFC requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
1-port 10-Gigabit Ethernet
- dCEF256 with a DFC
- QoS port architecture (Rx/Tx): 1p1q8t/1p2q1t
- Number of ports: 1
Number of port groups: 1 Port ranges per port group: 1 port in 1 group
|
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Optical Interface Module (OIM) for WS-X6502-10GE
|
|
10GBASE-LR serial 1310 nm long-reach OIM |
12.2(14)SX
|
|
10GBASE-ER serial 1550 nm extended-reach OIM |
12.2(14)SX
|
Gigabit Ethernet Switching Modules
WS-X6748-SFP 48-port Gigabit Ethernet SFP Switching Module
Note ● WS-X6748-SFP requires one of the following:
– WS-F6700-DFC3CXL
– WS-F6700-DFC3C
– WS-F6700-DFC3BXL
– WS-F6700-DFC3B
– WS-F6700-DFC3A
– WS-F6700-CFC
- WS-X6748-SFP ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
- WS-X6748-SFP is supported in the WS-C6503-E chassis.
- WS-X6748-SFP is not supported in the WS-C6503 and CISCO7603 chassis.
- In a 13-slot chassis, WS-X6748-SFP is supported only in slots 9 through 13 and does not power up in other slots.
- On WS-X6748-SFP ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6748-SFP ports that interconnect network devices.
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port Gigabit Ethernet SFP
– With DFC3: 2q8t/1p3q8t – With CFC: 1q8t/1p3q8t
- Dual switch-fabric connections
Fabric Channel #1: Ports 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48 Fabric Channel #2: Ports 1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23, 25, 27, 29, 31, 33, 35, 37, 39, 41, 43, 45, 47
- Number of ports: 48
Number of port groups: 4 Port ranges per port group: 1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 25, 27, 29, 31, 33, 35, 37, 39, 41, 43, 45, 47 26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 and DFC3C or DFC3CXL |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17d)SXB
|
WS-X6724-SFP 24-port Gigabit Ethernet SFP Switching Module
Note ● WS-X6724-SFP requires one of the following:
– WS-F6700-DFC3CXL
– WS-F6700-DFC3C
– WS-F6700-DFC3BXL (not supported in virtual switch mode)
– WS-F6700-DFC3B (not supported in virtual switch mode)
– WS-F6700-DFC3A (not supported in virtual switch mode)
– WS-F6700-CFC
- WS-X6724-SFP ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
- WS-X6724-SFP is supported in the WS-C6503-E chassis.
- WS-X6724-SFP is not supported in the WS-C6503 and CISCO7603 chassis.
- WS-X6724-SFP is supported in all slots of a 13-slot chassis.
- On WS-X6724-SFP ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6724-SFP ports that interconnect network devices.
- Use with Release 12.2(33)SXH or later requires switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
24-port Gigabit Mbps Ethernet SFP
- dCEF720 with a DFC
- CEF720 with WS-F6700-CFC
- Supports egress multicast replication
- QoS architecture:
– With DFC3: 2q8t/1p3q8t – With CFC: 1q8t/1p3q8t
- Number of ports: 24
Number of port groups: 2 Port ranges per port group: 1–12, 13–24
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 and DFC3C or DFC3CXL |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17a)SX
|
WS-X6816-GBIC 16-port Gigabit Ethernet GBIC Switching Module
Note ● WS-X6816-GBIC requires one of these for use with Supervisor Engine 720-10GE or Supervisor Engine 720:
– WS-F6K-DFC3BXL
– WS-F6K-DFC3B
– WS-F6K-DFC3A
- In a 13-slot chassis, WS-X6816-GBIC is supported only in slots 9 through 13 and does not power up in other slots.
- Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
16-port Gigabit Ethernet GBIC
- dCEF256
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Dual switch-fabric connections
Fabric Channel #1: Ports 1–8 Fabric Channel #2: Ports 9–16
- Number of ports: 16
Number of port groups: 2 Port ranges per port group: 1–8, 9–16
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
WS-X6516A-GBIC 16-Port Gigabit Ethernet GBIC Switching Module
Note ● Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
16-port Gigabit Ethernet GBIC
- dCEF256 with a DFC
- CEF256
- 1-MB per-port packet buffers
- Supports egress multicast replication
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Number of ports: 16
Number of port groups: 2 Port ranges per port group: 1–8, 9–16
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6516-GBIC 16-Port Gigabit Ethernet GBIC Switching Module
Note ● Use with Release 12.2(33)SXH or later and a DFC requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
- Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:
– Lower than 5.0
– 5.5 and higher
- Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.4 do not power up.
- With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.
- See external field notice 24494 for more information:
http://www.cisco.com/en/US/ts/fn/200/fn24494.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
16-port Gigabit Ethernet GBIC
- dCEF256 with a DFC
- CEF256
- 512-KB per-port packet buffers
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Number of ports: 16
Number of port groups: 2 Port ranges per port group: 1–8, 9–16
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6416-GBIC 16-port Gigabit Ethernet GBIC Switching Module
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
16-port Gigabit Ethernet GBIC
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Number of ports: 16
Number of port groups: 2 Port ranges per port group: 1–8, 9–16
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6408A-GBIC 8-port Gigabit Ethernet GBIC Switching Module
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
8-port Gigabit Ethernet GBIC
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Number of ports: 8
Number of port groups: 1 Port ranges per port group: 1–8
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6408-GBIC 8-port Gigabit Ethernet GBIC Switching Module
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
8-port Gigabit Ethernet GBIC
- QoS port architecture (Rx/Tx): 1q4t / 2q2t
- Number of ports: 8
Number of port groups: 1 Port ranges per port group: 1–8
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
10/100/1000 Ethernet Switching Modules
WS-X6748-GE-TX
Note ● WS-X6748-GE-TX requires one of the following:
– WS-F6700-DFC3CXL
– WS-F6700-DFC3C
– WS-F6700-DFC3BXL (not supported in virtual switch mode)
– WS-F6700-DFC3B (not supported in virtual switch mode)
– WS-F6700-DFC3A (not supported in virtual switch mode)
– WS-F6700-CFC
- WS-X6748-GE-TX ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3CXL, WS-F6700-DFC3C, WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.
- WS-X6748-GE-TX is supported in the WS-C6503-E chassis.
- WS-X6748-GE-TX is not supported in the WS-C6503 and CISCO7603 chassis.
- In a 13-slot chassis, WS-X6748-GE-TX is supported only in slots 9 through 13 and does not power up in other slots.
- On WS-X6748-GE-TX ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6748-GE-TX ports that interconnect network devices.
- Use with Release 12.2(33)SXH or later and a DFC requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port 10/100/1000 RJ-45
- dCEF720 with a DFC
- CEF720 with WS-F6700-CFC
- Supports egress multicast replication
- QoS architecture:
– With DFC3: 2q8t/1p3q8t – With CFC: 1q8t/1p3q8t
- Dual switch-fabric connections
Fabric Channel #1: Ports 25–48 Fabric Channel #2: Ports 1–24
- Number of ports: 48
Number of port groups: 4 Port ranges per port group: 1–12, 13–24, 25–36, 37–48
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17a)SX
|
WS-X6548-GE-TX, WS-X6548V-GE-TX, WS-X6548-GE-45AF
Note ● Release 12.2(17b)SXA and later releases provide support for more than 1 Gbps of traffic per EtherChannel on the WS-X6548-GE-TX (and voice-power daughtercard equipped) switching modules.
- WS-X6548-GE-TX (and voice-power daughtercard equipped) switching modules do not support these features:
– DFCs
– ISL trunking
– Jumbo frames
– 802.1Q tunneling
– Traffic storm control
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6548-GE-TX
WS-X6548V-GE-TX
WS-X6548-GE-45AF
|
48-port 10/100/1000 Mbps
- RJ-45
- CEF256
- WS-X6548-GE-TX supports:
– WS-F6K-VPWR-GE – WS-F6K-GE48-AF – WS-F6K-48-AF
- WS-X6548V-GE-TX has WS-F6K-VPWR-GE
- WS-X6548-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
- With WS-F6K-GE48-AF, supports up to 45 ports of ePoE (16.8W).
- QoS port architecture (Rx/Tx): 1q2t/1p2q2t
- Number of ports: 48
Number of port groups: 2 Port ranges per port group: 1–24, 25–48
- The aggregate bandwidth of each set of 8 ports (1–8, 9–16, 17–24, 25–32, 33–40, and 41–48) is 1 Gbps.
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 (except WS-F6K-GE48-AF or WS-F6K-48-AF) |
12.2(17a)SX
|
WS-F6K-GE48-AF or WS-F6K-48-AF with Supervisor Engine 720 |
12.2(17d)SXB
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-F6K-GE48-AF or WS-F6K-48-AF with Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6148E-GE-45AT
Note ● WS-X6148E-GE-45AT does not support:
– DFC
– Traffic storm control
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port 10/100/1000 Mbps
- RJ-45
- WS-X6148E-GE-45AT has WS-F6K-48-AT (IEEE 802.3at PoE)
– With Release 12.2(33)SXJ2 and later releases, supports Class 4 PoE+: 30.00 W at the PSE (12.95 W to 25.50 W at the PD). – With Releases earlier than Release 12.2(33)SXJ2, supports up to 45 ports of ePoE (16.8 W at the PSE, ePoE for 45 ports maximum).
- QoS port architecture (Rx/Tx): 1q2t/1p3q8t
- Number of ports: 48
Number of port groups: 6 Port ranges per port group: 1–8, 9–16, 17–24, 25–32, 33–40, 41–48
- The aggregate bandwidth of each set of 8 ports (1–8, 9–16, 17–24, 25–32, 33–40, and 41–48) is 1 Gbps.
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXI4
|
With Supervisor Engine 720 |
With Supervisor Engine 32 |
WS-X6148A-GE-TX, WS-X6148A-GE-45AF
Note ● WS-X6148A-GE-TX and WS-X6148A-GE-45AF do not support these features:
– WS-F6K-DFC3A, WS-F6K-DFC3B, or WS-F6K-DFC3BXL
– Traffic storm control
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6148A-GE-TX
WS-X6148A-GE-45AF
|
48-port 10/100/1000 Mbps
- RJ-45
- WS-X6148A-GE-TX supports WS-F6K-GE48-AF or WS-F6K-48-AF
- WS-X6148A-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
- With WS-F6K-GE48-AF, supports up to 45 ports of ePoE (16.8W).
- QoS port architecture (Rx/Tx): 1q2t/1p3q8t
- Number of ports: 48
Number of port groups: 6 Port ranges per port group: 1–8, 9–16, 17–24, 25–32, 33–40, 41–48
- The aggregate bandwidth of each set of 8 ports (1–8, 9–16, 17–24, 25–32, 33–40, and 41–48) is 1 Gbps.
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6148-GE-TX, WS-X6148V-GE-TX, WS-X6148-GE-45AF
Note ● WS-X6148-GE-TX, WS-X6148V-GE-TX, and WS-X6148-GE-45AF do not support these features:
– More than 1 Gbps of traffic per EtherChannel
– WS-F6K-DFC3A, WS-F6K-DFC3B, or WS-F6K-DFC3BXL
– ISL trunking
– Jumbo frames
– 802.1Q tunneling
– Traffic storm control
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6148-GE-TX
WS-X6148V-GE-TX
WS-X6148-GE-45AF
|
48-port 10/100/1000 Mbps
- RJ-45
- WS-X6148-GE-TX supports:
– WS-F6K-VPWR-GE – WS-F6K-GE48-AF – WS-F6K-48-AF
- WS-X6148V-GE-TX has WS-F6K-VPWR-GE
- WS-X6148-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
- With WS-F6K-GE48-AF, supports up to 45 ports of ePoE (16.8W).
- QoS port architecture (Rx/Tx): 1q2t/1p2q2t
- Number of ports: 48
Number of port groups: 2 Port ranges per port group: 1–24, 25–48
- The aggregate bandwidth of each port group is 1 Gbps.
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 (except WS-F6K-GE48-AF or WS-F6K-48-AF) |
12.2(17a)SX
|
WS-F6K-GE48-AF or WS-F6K-48-AF with Supervisor Engine 720 |
12.2(17d)SXB
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-F6K-GE48-AF or WS-F6K-48-AF with Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6516-GE-TX
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
16-port 10/100/1000BASE-T
- dCEF256 with a DFC
- CEF256
- QoS port architecture (Rx/Tx): 1p1q4t / 1p2q2t
- Number of ports: 16
Number of port groups: 2 Port ranges per port group: 1–8, 9–16
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Fast Ethernet Switching Modules
Note Fast Ethernet switching modules are not supported in VSS mode.
WS-X6148-FE-SFP
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port 100BASE-FX
- Requires Fast Ethernet SFPs
- QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t
- Number of ports: 48
Number of port groups: 3 Port ranges per port group: 1–16, 17–32, and 33–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6524-100FX-MM
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
24-port 100FX Ethernet multimode
- dCEF256 with a DFC
- CEF256
- QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
- Number of ports: 24
Number of port groups: 1 Port ranges per port group: 1–24
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6324-100FX-MM
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
24-port 100FX Ethernet
- Single mode and multimode MT-RJ
- 128-KB per-port packet buffers
- QoS port architecture (Rx/Tx): 1q4t / 2q2t
- Number of ports: 24
Number of port groups: 2 Port ranges per port group: 1–12, 13–24
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Ethernet/Fast Ethernet (10/100) Switching Modules
- WS-X6548-RJ-45
- WS-X6548-RJ-21
- WS-X6148X2-RJ-45, WS-X6148X2-45AF
- WS-X6196-RJ-21, WS-X6196-21AF
- WS-X6348-RJ-45, WS-X6348-RJ-45V
- WS-X6348-RJ-21V
- WS-X6148A-RJ-45, WS-X6148A-45AF
- WS-X6148-RJ-45, WS-X6148-RJ45V, WS-X6148-45AF
- WS-X6148-RJ-21, WS-X6148-RJ21V, WS-X6148-21AF
- WS-F6K-FE48X2-AF
- WS-F6K-GE48-AF, WS-F6K-48-AF
- WS-F6K-GE48-AF, WS-F6K-48-AF
Note Ethernet/Fast Ethernet (10/100) switching modules are not supported in VSS mode.
WS-X6548-RJ-45
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port 10/100TX RJ-45
- dCEF256 with a DFC
- CEF256
- QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
- Number of ports: 48
Number of port groups: 1 Port ranges per port group: 1–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6548-RJ-21
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port 10/100TX RJ-21
- dCEF256 with a DFC
- CEF256
- QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
- Number of ports: 48
Number of port groups: 1 Port ranges per port group: 1–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6148X2-RJ-45, WS-X6148X2-45AF
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6148X2-RJ-45
WS-X6148X2-45AF
|
96-port 10/100TX RJ-45
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF3
|
With Supervisor Engine 32 |
12.2(18)SXF3
|
WS-X6196-RJ-21, WS-X6196-21AF
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6196-RJ-21
WS-X6196-21AF
|
96-port 10/100TX RJ-21
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF3
|
With Supervisor Engine 32 |
12.2(18)SXF3
|
WS-X6348-RJ-45, WS-X6348-RJ-45V
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6348-RJ-45
WS-X6348-RJ-45V
|
48-port 10/100TX RJ-45
- 128-KB per-port packet buffers
- QoS port architecture (Rx/Tx): 1q4t / 2q2t
- WS-X6348-RJ-45 supports WS-F6K-VPWR
- WS-X6348-RJ-45V has WS-F6K-VPWR
- Number of ports: 48
Number of port groups: 4 Port ranges per port group: 1–12, 13–24, 25–36, 37–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6348-RJ-21V
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
48-port 10/100TX RJ-21
- 128-KB per-port packet buffers
- QoS port architecture (Rx/Tx): 1q4t / 2q2t
- Has WS-F6K-VPWR
- Number of ports: 48
Number of port groups: 4 Port ranges per port group: 1–12, 13–24, 25–36, 37–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6148A-RJ-45, WS-X6148A-45AF
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6148A-RJ-45
WS-X6148A-45AF
|
48-port 10/100TX RJ-45
- 5.3-MB per-port packet buffers
- QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t
- WS-X6148A-RJ-45 supports WS-F6K-GE48-AF or WS-F6K-48-AF
- WS-X6148A-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF
- Number of ports: 48
Number of port groups: 6 Port ranges per port group: 1–8, 9–16, 17–24, 25–32, 33–40, 41–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-X6148-RJ-45, WS-X6148-RJ45V, WS-X6148-45AF
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6148-RJ-45
WS-X6148-RJ45V
WS-X6148-45AF
|
48-port 10/100TX RJ-45
- 128-KB per-port packet buffers
- QoS port architecture (Rx/Tx): 1q4t / 2q2t
- WS-X6148-RJ-45 supports WS-F6K-VPWR
- WS-X6148-RJ-45V has WS-F6K-VPWR
- WS-X6148-45AF has WS-F6K-48-AF
- Number of ports: 48
Number of port groups: 4 Port ranges per port group: 1–12, 13–24, 25–36, 37–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 (except with WS-F6K-48-AF) |
12.2(14)SX
|
WS-F6K-48-AF with Supervisor Engine 720 |
12.2(17d)SXB
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-F6K-48-AF with Supervisor Engine 32 |
WS-X6148-RJ-21, WS-X6148-RJ21V, WS-X6148-21AF
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-X6148-RJ-21
WS-X6148-RJ21V
WS-X6148-21AF
|
48-port 10/100TX RJ-21
- 128-KB per-port packet buffers
- QoS port architecture (Rx/Tx): 1q4t / 2q2t
- WS-X6148-RJ-21 supports WS-F6K-VPWR
- WS-X6148-RJ-21V has WS-F6K-VPWR
- WS-X6148-21AF has WS-F6K-48-AF
- Number of ports: 48
Number of port groups: 4 Port ranges per port group: 1–12, 13–24, 25–36, 37–48
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 (except with WS-F6K-48-AF) |
12.2(14)SX
|
WS-F6K-48-AF with Supervisor Engine 720 |
12.2(17d)SXB
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-F6K-48-AF with Supervisor Engine 32 |
Power over Ethernet Daughtercards
Note The IEEE 802.3at power over ethernet (PoE) daughtercard is available only with the WS-X6148E-GE-45AT switching module.
WS-F6K-FE48X2-AF
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
IEEE 802.3af PoE daughtercard for WS-X6148X2-RJ-45 and WS-X6196-RJ-21. |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-F6K-GE48-AF, WS-F6K-48-AF
Note ● WS-F6K-GE48-AF and WS-F6K-48-AF are not FRUs for these switching modules:
– WS-X6148-RJ-45 or WS-X6148-RJ-45V (replace with WS-X6148-45AF-UG=).
– WS-X6148-RJ-21 or WS-X6148-RJ-21V (replace with WS-X6148-21AF-UG=).
- With WS-X6548-GE-TX, WS-X6148-GE-TX, and WS-X6148A-GE-TX, supports up to 45 ports of ePoE (16.8W).
(append “=” for spares)
|
|
Minimum
Software
Versions
|
WS-F6K-GE48-AF
WS-F6K-48-AF
|
IEEE 802.3af PoE daughtercard for:
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17d)SXB
|
WS-F6K-VPWR-GE
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Prestandard PoE daughtercard for WS-X6548-GE-TX and WS-X6148-GE-TX |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17a)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
WS-F6K-VPWR
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Prestandard PoE daughtercard for:
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
X2 Modules
Note ● WS-X6708-10GE and WS-X6716-10G do not support X2 modules shipped before the release of WS-X6708-10GE with Release 12.2(18)SXF5. The unsupported X2 modules are labeled with a number that ends with -01. (This restriction does not apply to X2-10GB-LRM.)
- All X2 modules shipped since WS-X6716-10G became available provide EMI compliance with WS-X6716-10G.
- Some X2 modules shipped before WS-X6716-10G became available might not provide EMI compliance with WS-X6716-10G. See the information listed for each type of X2 module in the following table.
- For information about X2 modules, see the Cisco 10GBASE X2 Modules data sheet:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6574/product_data_sheet0900aecd801f92aa.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
10G X2 to SFP+ Converter |
12.2(33)SXI2
|
10 Gbps Ethernet SFP+ Modules |
SFP-10G-LR—10GBASE-LR 1310 nm SMF |
12.2(33)SXJ1
|
SFP-10G-LRM—10GBASE-LRM 1310 nm MMF and SMF |
12.2(33)SXI4 (12.2(33)SXI4a
or later recommended)
|
SFP-10G-SR—10GBASE-SR 850 nm MMF |
12.2(33)SXI2
|
SFP-H10GB-CU1M—1m Twinax cable, passive, 30AWG cable assembly |
SFP-H10GB-CU3M—3m Twinax cable, passive, 30AWG cable assembly |
SFP-H10GB-CU5M—5m Twinax cable, passive, 24AWG cable assembly |
|
10GBASE-DWDM 1560.61 nm X2 (100-GHz ITU grid) |
ITU 21
|
12.2(33)SXI
|
|
10GBASE-DWDM 1559.79 nm X2 (100-GHz ITU grid) |
ITU 22
|
|
10GBASE-DWDM 1558.98 nm X2 (100-GHz ITU grid) |
ITU 23
|
|
10GBASE-DWDM 1558.17 nm X2 (100-GHz ITU grid) |
ITU 24
|
|
10GBASE-DWDM 1556.55 nm X2 (100-GHz ITU grid) |
ITU 26
|
|
10GBASE-DWDM 1555.75 nm X2 (100-GHz ITU grid) |
ITU 27
|
|
10GBASE-DWDM 1554.94 nm X2 (100-GHz ITU grid) |
ITU 28
|
|
10GBASE-DWDM 1554.13 nm X2 (100-GHz ITU grid) |
ITU 29
|
|
10GBASE-DWDM 1552.52 nm X2 (100-GHz ITU grid) |
ITU 31
|
|
10GBASE-DWDM 1551.72 nm X2 (100-GHz ITU grid) |
ITU 32
|
|
10GBASE-DWDM 1550.92 nm X2 (100-GHz ITU grid) |
ITU 33
|
|
10GBASE-DWDM 1550.12 nm X2 (100-GHz ITU grid) |
ITU 34
|
|
10GBASE-DWDM 1548.51 nm X2 (100-GHz ITU grid) |
ITU 36
|
|
10GBASE-DWDM 1547.72 nm X2 (100-GHz ITU grid) |
ITU 37
|
|
10GBASE-DWDM 1546.92 nm X2 (100-GHz ITU grid) |
ITU 38
|
|
10GBASE-DWDM 1546.12 nm X2 (100-GHz ITU grid) |
ITU 39
|
|
10GBASE-DWDM 1544.53 nm X2 (100-GHz ITU grid) |
ITU 41
|
|
10GBASE-DWDM 1543.73 nm X2 (100-GHz ITU grid) |
ITU 42
|
|
10GBASE-DWDM 1542.94 nm X2 (100-GHz ITU grid) |
ITU 43
|
|
10GBASE-DWDM 1542.14 nm X2 (100-GHz ITU grid) |
ITU 44
|
|
10GBASE-DWDM 1540.56 nm X2 (100-GHz ITU grid) |
ITU 46
|
|
10GBASE-DWDM 1539.77 nm X2 (100-GHz ITU grid) |
ITU 47
|
|
10GBASE-DWDM 1538.98 nm X2 (100-GHz ITU grid) |
ITU 48 |
|
10GBASE-DWDM 1538.19 nm X2 (100-GHz ITU grid) |
ITU 49 |
|
10GBASE-DWDM 1536.61 nm X2 (100-GHz ITU grid) |
ITU 51 |
|
10GBASE-DWDM 1535.82 nm X2 (100-GHz ITU grid) |
ITU 52 |
|
10GBASE-DWDM 1535.04 nm X2 (100-GHz ITU grid) |
ITU 53 |
|
10GBASE-DWDM 1534.25 nm X2 (100-GHz ITU grid) |
ITU 54 |
|
10GBASE-DWDM 1532.68 nm X2 (100-GHz ITU grid) |
ITU 56 |
|
10GBASE-DWDM 1531.90 nm X2 (100-GHz ITU grid) |
ITU 57 |
|
10GBASE-DWDM 1531.12 nm X2 (100-GHz ITU grid) |
ITU 58 |
|
10GBASE-DWDM 1530.33 nm X2 (100-GHz ITU grid) |
ITU 59 |
|
10GBASE-T X2 Module for CAT6A/CAT7 copper cable |
12.2(33)SXJ1 |
|
10GBASE-ZR X2 Module for SMF |
12.2(33)SXI
|
|
10GBASE for CX4 (copper) cable |
12.2(18)SXF5
|
|
10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF) Note X2-10GB-ER modules labeled with a number that ends with -02 do not provide EMI compliance with WS-X6716-10G. |
12.2(18)SXF5
|
|
10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF) Note X2-10GB-LR modules labeled with a number that ends with -02 or -03 do not provide EMI compliance with WS-X6716-10G. |
12.2(18)SXF5
|
|
10GBASE-LRM for FDDI-grade multimode fiber (MMF) Note Not supported by the show idprom command. (CSCsj35671) |
12.2(18)SXF8
|
|
10GBASE-LX4 Serial 1310-nm multimode (MMF) Note
- See field notice 62840 for information about unsupported 10GBASE-LX4 modules:
http://www.cisco.com/en/US/ts/fn/misc/FN62840.html
|
12.2(18)SXF5
|
|
10GBASE-SR Serial 850-nm short-reach multimode (MMF) |
12.2(18)SXF5
|
XENPAKs
Note ● For information about DWDM XENPAKs, see the Cisco 10GBase DWDM XENPAK Modules data sheet:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6576/product_data_sheet0900aecd801f9333.html
- For information about other XENPAKs, see the Cisco 10GBASE XENPAK Modules data sheet:
http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps5138/product_data_sheet09186a008007cd00_ps5251_Products_Data_Sheet.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
10GBASE-LRM XENPAK Module for MMF Note Not supported by the show idprom command. (CSCsl21260) |
12.2(33)SXH1
|
|
10GBASE dense wavelength-division multiplexing (DWDM) 100-GHz ITU grid |
12.2(18)SXE
|
|
10GBASE receive-only wavelength division multiplexing (WDM) |
12.2(18)SXE
|
|
10GBASE for CX4 (copper) cable; uses Infiniband connectors |
12.2(17d)SXB1
|
|
10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF) Note XENPAK-10GB-ER units with Part No. 800-24557-01 are not supported, as described in this external field notice (CSCee47030): http://www.cisco.com/en/US/ts/fn/200/fn29736.html |
12.2(17a)SX
|
|
10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF) |
12.2(17a)SX
|
|
10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF) |
12.2(17a)SX
|
|
10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF) |
12.2(17a)SX
|
|
10GBASE-LW XENPAK Module with WAN PHY for SMF Note XENPAK-10GB-LW operates at an interface speed compatible with SONET/SDH OC-192/STM-64. XENPAK-10GB-LW links might go up and down if the data rate exceeds 9Gbs. (CSCsi58211) |
12.2(18)SXE
|
|
10GBASE-LX4 Serial 1310-nm multimode (MMF) |
12.2(17a)SX1
|
|
10GBASE-SR Serial 850-nm short-reach multimode (MMF) |
12.2(17a)SX1
|
|
10GBASE for any SMF type |
12.2(18)SXF
|
Small Form-Factor Pluggable (SFP) Modules
These sections describe SFPs:
Gigabit Ethernet SFP Modules
Note ● For information about coarse wavelength-division multiplexing (CWDM) SFPs, see the Cisco CWDM GBIC and SFP Solutions data sheet:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6575/product_data_sheet09186a00801a557c_ps4999_Products_Data_Sheet.html
- For information about DWDM SFPs, see the Cisco Dense Wavelength-Division Multiplexing Small Form-Factor Pluggable Module data sheet:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6576/product_data_sheet0900aecd80582763.html
- See the “Unsupported Hardware” section for information about unsupported DWDM-SFPs.
- For information about other SFPs, see the Cisco SFP Optics For Gigabit Ethernet Applications data sheet:
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
1000BASE-BX10 SFP module for single-strand SMF, 1490-nm TX/1310-nm RX wavelength |
12.2(18)SXE
|
|
1000BASE-BX10 SFP module for single-strand SMF, 1310-nm TX/1490-nm RX wavelength |
12.2(18)SXE
|
|
1000BASE-LX/LH SFP |
12.2(17a)SX
|
|
1000BASE-SX SFP |
12.2(14)SX
|
|
1000BASE-T 10/100/1000 SFP module Note Supported only at 1000 Mbps. |
12.2(17a)SX
|
|
1000BASE-ZX SFP module |
12.2(17d)SXB1
|
|
CWDM 1470-nm (Gray) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1490-nm (Violet) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1510-nm (Blue) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1530-nm (Green) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1550-nm (Yellow) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1570-nm (Orange) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1590-nm (Red) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
CWDM 1610-nm (Brown) Gigabit Ethernet, 1 and 2 Gb Fibre Channel SFP module |
12.2(17a)SX
|
|
1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid) SFP module |
12.2(33)SXH
|
|
1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
|
1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid) SFP module |
12.2(18)SXF8
|
Gigabit Interface Converters (GBICs)
Note The support listed in this section applies to all modules that use GBICs.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Receive-only wavelength division multiplexing (WDM) GBIC |
12.2(18)SXE
|
|
Dense wavelength division multiplexing (DWDM) GBIC |
12.2(17a)SX
|
|
Cisco 1000BASE-CWDM GBIC, 1470 nm (Gray) |
12.2(17a)SX
|
|
Cisco 1000BASE-CWDM GBIC, 1490 nm (Violet) |
|
Cisco 1000BASE-CWDM GBIC, 1510 nm (Blue) |
|
Cisco 1000BASE-CWDM GBIC, 1530 nm (Green) |
|
Cisco 1000BASE-CWDM GBIC, 1550 nm (Yellow) |
|
Cisco 1000BASE-CWDM GBIC, 1570 nm (Orange) |
|
Cisco 1000BASE-CWDM GBIC, 1590 nm (Red) |
|
Cisco 1000BASE-CWDM GBIC, 1610 nm (Brown) |
|
1000BASET GBIC |
12.2(14)SX
|
|
Short wavelength, 1000BASE-SX |
12.2(14)SX
|
|
Long wavelength/long haul, 1000BASE-LX/LH |
12.2(14)SX
|
|
Extended distance, 1000BASE-ZX |
12.2(14)SX
|
Shared Port Adapter (SPA) Interface Processors (SIPs)
Note ● SIPs are supported only in images that contain “_wan” in the image name.
- See the “FPD Image Packages” section for information about additional procedures required to support SIPs with Release 12.2(18)SXE and later releases.
Product ID
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
SPA Interface Processor-600 Note
- 7600-SIP-600 has a WS-F6700-DFC3BXL.
- Not supported with Supervisor Engine 32.
- In Release 12.2(33)SXJ1 and later releases, CDP is disabled by default on 7600-SIP-600 ports ( CSCtk12860).
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXI |
With Supervisor Engine 720 Note
- Not supported in PFC3A mode.
- Not supported in release 12.2(33)SXH and rebuilds.
|
12.2(18)SXF 12.2(33)SXI |
|
SPA Interface Processor-400 |
With Supervisor Engine 720-10GE
in VSS mode
|
12.2(33)SXI4 |
With Supervisor Engine 720-10GE |
12.2(33)SXH |
With Supervisor Engine 720 (not supported in PFC3A mode) |
12.2(18)SXE |
With Supervisor Engine 32 |
12.2(18)SXF |
|
SPA Interface Processor-200 |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(18)SXE |
With Supervisor Engine 32 |
12.2(18)SXF |
Shared Port Adapters (SPAs)
These sections describe SPAs:
Ethernet SPAs
These sections describe Ethernet SPAs:
10-Gigabit Ethernet SPAs
Note Release 12.2(33)SXH and rebuilds do not support 7600-SIP-600.
(append “=” for spares)
|
|
|
Minimum
Software
Versions
|
|
7600-SIP-400 |
1-Port 10 Gigabit Ethernet SPA |
12.2(33)SXI2
|
|
7600-SIP-600 |
1-port 10-Gigabit Ethernet SPA |
12.2(33)SXI
|
XFP Modules Supported in 10-Gigabit Ethernet SPAs
|
|
10-Gigabit Ethernet LR (10 km) |
Gigabit Ethernet SPAs
Note Release 12.2(33)SXH and rebuilds do not support 7600-SIP-600.
(append “=” for spares)
|
|
|
Minimum
Software
Versions
|
|
7600-SIP-600 |
10-port Gigabit Ethernet SPA, SFP Optics |
12.2(33)SXI
|
|
7600-SIP-600 |
5-port Gigabit Ethernet SPA, SFP Optics |
12.2(33)SXJ
|
|
7600-SIP-600 |
5-port Gigabit Ethernet SPA, SFP Optics |
12.2(33)SXI
|
|
7600-SIP-400 |
2-port Gigabit Ethernet SPA, SFP Optics, version 2 |
12.2(33)SXI
|
|
7600-SIP-400 |
2-port Gigabit Ethernet SPA, SFP Optics |
12.2(18)SXF
|
SFPs Supported in Gigabit Ethernet SPAs
|
|
Extended Temperature SX SFP |
12.2(18)SXF
|
|
Extended Temperature LX/LH SFP |
|
Extended Temperature ZX SFP |
|
Cisco 1000BASE-T SFP (NEBS 3 ESD) |
12.2(33)SXH
|
10/100 Mbps Ethernet SPAs
(append “=” for spares)
|
|
|
Minimum
Software
Versions
|
|
7600-SIP-200 |
8-port 10/100 Ethernet SPA TX |
12.2(33)SXH
|
|
7600-SIP-200 |
4-port 10/100 Ethernet SPA TX |
12.2(33)SXH
|
POS SPAs
Note ● Release 12.2(33)SXH and rebuilds do not support 7600-SIP-600.
- With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.
(append “=” for spares)
|
|
|
Minimum
Software
Versions
|
|
7600-SIP-600 |
1-port OC-192c/STM-64 POS/RPR SPA, VSR-1 |
12.2(33)SXI
|
|
7600-SIP-600 |
1-port OC-192c/STM-64 POS/RPR SPA, SM-LR |
12.2(33)SXI
|
|
7600-SIP-600 |
1-port OC-192c/STM-64 POS/RPR SPA, XFP Optics |
12.2(33)SXI
|
XFP Modules Supported in SPA-OC192POS-XFP
|
XFP-10GLR-OC192SR Single-Mode (SM) Short Reach (SR) |
XFP-10GER-OC192IR Single-Mode (SM) Intermediate Reach (IR-2) |
|
7600-SIP-600 |
1-port OC-192c/STM-64 POS/RPR SPA, VSR-1 |
12.2(33)SXI
|
|
7600-SIP-400 |
2-Port OC-48 POS/RPR SPA Note Requires SFPs. |
12.2(33)SXI
|
|
7600-SIP-400 |
1-Port OC-48 POS/RPR SPA Note Requires SFPs. |
12.2(18)SXF10
|
|
7600-SIP-200 7600-SIP-400 |
2-port OC-3c/STM-1c POS SPA Note Requires SFPs. |
12.2(18)SXE
|
|
7600-SIP-200 7600-SIP-400 |
4-port OC-3c/STM-1c POS SPA Note Requires SFPs. |
12.2(18)SXE
|
|
7600-SIP-400 |
1-port OC-12c/STM-4c POS SPA Note Requires an SFP. |
12.2(18)SXE
|
ATM SPAs
Note ● Release 12.2(33)SXH and rebuilds do not support ATM SPAs.
- With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.
SFPs for OC3 and OC12 POS and ATM SPAs
(append “=” for spares)
|
|
|
OC-3/STM-1 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, MMF, LC connector |
|
OC-3/STM-1 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, LC connector |
|
OC-3/STM-1 pluggable intermediate-reach (15 km) transceiver module, 1310-nm wavelength, LC connector |
|
OC-3/STM-1 pluggable long-reach (40 km) transceiver module, 1310-nm wavelength, LC connector |
|
OC-3/STM-1 pluggable long-reach (80 km) transceiver module, 1550-nm wavelength, LC connector |
|
OC-12/STM-4 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, MMF, LC connector |
|
OC-12/STM-4 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, LC connector |
|
OC-12/STM-4 pluggable intermediate-reach (15 km) transceiver module, 1310-nm wavelength |
|
OC-12/STM-4 pluggable long-reach (40 km) transceiver module, 1310-nm wavelength, LC connector |
|
OC-12/STM-4 pluggable long-reach (80 km) transceiver module, 1550-nm wavelength, LC connector |
Serial SPAs
Note With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.
Services SPA Carrier (SSC) and Services SPAs
Note If you are upgrading from a Release 12.2(18)SXF or rebuild image to a Release 12.2(33)SXH or later image, be aware of CSCsv30090, “SPA-IPsec-2G VRF: vlan 1 mistakenly trunked on upgrade from SXF to SXH.”
Product ID
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Services SPA Carrier (SSC) and IPsec SPA |
With Supervisor Engine 720-10GE
in VSS mode
|
12.2(33)SXJ1 |
With Supervisor Engine 720-10GE |
12.2(33)SXI |
With Supervisor Engine 720 |
With Supervisor Engine 32 |
7600-SSC-400
SPA-IPSEC-2G
|
Services SPA Carrier (SSC) and IPsec SPA Note
- 7600-SSC-400 does not maintain state when an NSF with SSO redundancy mode switchover occurs.
- See the “FPD Image Packages” section for information about additional procedures required to support SPA-IPSEC-2G with Release 12.2(18)SXE and later releases.
- SPA-IPSEC-2G does not support TACACS+ authentication for IPsec.
|
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(18)SXE2 |
With Supervisor Engine 32 |
12.2(18)SXF2 |
Enhanced FlexWAN Module
Note ● Supported only in images that contain "_wan" in the image name.
- With Release 12.2(33)SXI and later releases where CSCso97991 is not resolved, you must configure an appropriate burst size when you configure QoS policing on WAN ports. Do not rely on the burst size calculated by QoS.
(append “=” for spares)
|
|
|
|
Enhanced FlexWAN Module; CEF256 |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(17b)SXA
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Enhanced FlexWAN Module Port Adapters
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
2-port Fast Ethernet Port Adapter |
12.2(18)SXE
|
|
1-port Fast Ethernet Port Adapter |
12.2(18)SXE
|
|
1-port Packet over SONET OC3c/STM1 Port Adapter |
12.2(18)SXE
|
|
2-port POS OC3c/STM1
– SFP-OC3-MM, short range, multimode fiber – SFP-OC3-IR1, intermediate range, single-mode fiber – SFP-OC3-LR1, long range, single-mode fiber |
12.2(17b)SXA
|
PA-POS-OC3MM
PA-POS-OC3SMI
PA-POS-OC3SML
|
Packet over SONET (OC-3) |
12.2(14)SX
|
|
1-port ATM OC-3c/STM-1 multimode port adapter, enhanced |
12.2(14)SX
|
|
1-port ATM OC-3c/STM-1 single-mode (IR) port adapter, enhanced |
12.2(14)SX
|
|
1-port ATM OC-3c/STM-1 single-mode (LR) port adapter, enhanced |
12.2(14)SX
|
|
1-port ATM DS3 port adapter, enhanced |
12.2(14)SX
|
|
1-port ATM E3 port adapter, enhanced |
12.2(14)SX
|
PA-A3-OC3MM
PA-A3-OC3SMI
PA-A3-T3
PA-A3-OC3SML
PA-A3-E3
PA-A3-8T1IMA
PA-A3-8E1IMA
|
ATM with traffic shaping Note These port adapters do not support LANE when installed in the FlexWAN module. |
12.2(14)SX
|
PA-T3
PA-T3+
PA-2T3
PA-2T3+
PA-E3
PA-2E3
PA-MC-T3
PA-MC-E3
PA-MC-2T3+
|
T3/E3 (clear-channel and channelized) |
12.2(14)SX
|
PA-4T+
PA-8T-V35
PA-8T-X21
PA-8T-232
PA-MC-2E1/120
PA-MC-8T1
PA-MC-8E1/120
PA-MC-2T1
PA-MC-4T1
|
T1/E1 |
12.2(14)SX
|
|
T1/E1 |
12.2(17)SX
|
|
Multichannel T1/E1 8PRI Note This port adapter does not support ISDN PRI when installed in the FlexWAN module. |
12.2(14)SX
|
|
HSSI |
12.2(14)SX
|
|
Multichannel STM-1 |
12.2(14)SX
|
Service Modules
Note ● For service modules that run their own software, see the service module software release notes for information about the minimum required service module software version.
- With SPAN configured to include a port-channel interface to support a service module, be aware of CSCth03423 and CSCsx46323.
- EtherChannel configuration can impact some service modules. In particular, distributed EtherChannels (DECs) can interfere with service module traffic. See this field notice for more information:
http://www.cisco.com/en/US/ts/fn/610/fn61935.html
Application Control Engine (ACE) Module
Note ● ACE30-MOD-K9, ACE10-6500-K9, and ACE20-MOD-K9 run their own software—See these publications:
http://www.cisco.com/en/US/products/ps6906/tsd_products_support_model_home.html
See the module software release notes for information about the minimum required service module software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Application Control Engine (ACE) module |
With Supervisor Engine 720-10GE |
12.2(33)SXI4
|
With Supervisor Engine 720 |
ACE10-6500-K9
ACE20-MOD-K9
|
Application Control Engine (ACE) module Note With releases earlier than Release 12.2(33)SXI, not supported in virtual switch mode. |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF4
|
Anomaly Guard Module(AGM)
Note ● WS-SVC-AGM-1-K9 runs its own software—See these publications:
http://www.cisco.com/en/US/products/ps6236/tsd_products_support_model_home.html
- See the WS-SVC-AGM-1-K9 software release notes for information about the minimum required WS-SVC-AGM-1-K9 software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Anomaly Guard Module (AGM) |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH1
|
With Supervisor Engine 720 |
12.2(18)SXD3
|
Traffic Anomaly Detector Module (ADM)
Note ● WS-SVC-ADM-1-K9 runs its own software—See these publications:
http://www.cisco.com/en/US/products/ps6236/tsd_products_support_model_home.html
- See the WS-SVC-ADM-1-K9 software release notes for information about the minimum required WS-SVC-ADM-1-K9 software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Traffic Anomaly Detector Module (ADM) |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH1
|
With Supervisor Engine 720 |
12.2(18)SXD3
|
ASA Services Module
Note ● Supported only with 6500 E-series chassis: WS-C6513-E, WS-C6509-V-E, WS-C6509-E, WS-C6506-E, WS-C6504-E, and WS-C6503-E.
- Not supported in PFC3A mode.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
ASA Services Module |
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
|
ASA Services Module |
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
|
ASA Services Module |
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
Communication Media Module (CMM)
Note ● WS-SVC-CMM runs its own software—See these publications:
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/cmm/release/notes/OL_4847.html
- See the WS-SVC-CMM software release notes for information about the minimum required WS-SVC-CMM software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Communication Media Module |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Communication Media Module Port Adapters for WS-SVC-CMM
|
|
6-Port E1 Interface Port Adapter |
|
6-Port T1 Interface Port Adapter |
|
Adhoc Conferencing and Transcoding Port Adapter |
|
24-Port FXS Interface Port Adapter |
Content Switching Module (CSM)
Note ● WS-X6066-SLB-APC runs its own software—See these publications:
http://www.cisco.com/en/US/products/hw/modules/ps2706/ps780/tsd_products_support_model_home.html
- See the WS-X6066-SLB-APC software release notes for information about the minimum required WS-X6066-SLB-APC software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Content Switching Module (CSM) |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXI2
(Not supported in Release 12.2(33)SXJ and rebuilds)
|
With Supervisor Engine 720 |
Content Switching Module with SSL (CSM-S)
Note ● WS-X6066-SLB-S-K9 runs its own software—See these publications:
http://www.cisco.com/en/US/products/hw/modules/ps2706/ps780/tsd_products_support_model_home.html
- See the WS-X6066-SLB-S-K9 software release notes for information about the minimum required WS-X6066-SLB-S-K9 software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Content Switching Module with SSL (CSM-S) |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXI2
(Not supported in Release 12.2(33)SXJ and rebuilds)
|
With Supervisor Engine 720 |
Firewall Services Module (FWSM)
Note ● With Firewall Services Module Software Release 2.3(1) and later releases, WS-SVC-FWM-1-K9 maintains state when an NSF with SSO redundancy mode switchover occurs.
- The FWSM runs its own software—See these publications:
http://www.cisco.com/en/US/products/hw/modules/ps2706/ps4452/tsd_products_support_model_home.html
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Firewall Services Module; CEF256 |
With Supervisor Engine 720-10GE
in VSS mode
|
12.2(33)SXI |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX1
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Intrusion Detection System Modules (IDSMs)
Note ● The IDSM runs its own software—See these publications:
http://www.cisco.com/en/US/products/hw/modules/ps2706/ps5058/tsd_products_support_model_home.html
See the IDSM software release notes for information about the minimum required IDSM software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Intrusion Detection System Module 2; CEF256 |
With Supervisor Engine 720-10GE
in VSS mode
|
12.2(33)SXI |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX1
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Network Analysis Modules (NAMs)
Note ● Network Analysis Modules run their own software—See this publication for more information:
http://www.cisco.com/en/US/products/sw/cscowork/ps5401/prod_release_notes_list.html
- See the NAM software release notes for information about the minimum required NAM software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Network Analysis Module 3 |
With Supervisor Engine 720-10GE |
12.2(33)SXJ1
|
With Supervisor Engine 720 |
- Supported only with 6500 E-series chassis: WS-C6513-E, WS-C6509-V-E, WS-C6509-E, WS-C6506-E, WS-C6504-E, and WS-C6503-E.
- Not supported in PFC3A mode.
|
WS-SVC-NAM-2
WS-SVC-NAM-1
|
Network Analysis Module 2 Network Analysis Module 1 |
With Supervisor Engine 720-10GE
(not supported in VSS mode)
|
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX1
|
With Supervisor Engine 32 |
12.2(18)SXF
|
Secure Sockets Layer (SSL) Services Module
Note ● Supported in virtual switch mode.
- WS-SVC-SSL-1 does not maintain state when an NSF with SSO redundancy mode switchover occurs.
- WS-SVC-SSL-1 runs its own software—See the publications listed here for more information:
http://www.cisco.com/en/US/products/hw/switches/ps708/prod_release_notes_list.html
- See the WS-SVC-SSL-1 software release notes for information about the minimum required WS-SVC-SSL-1 software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Secure Sockets Layer (SSL) Services Module |
With Supervisor Engine 720-10GE |
12.2(33)SXI4
- 12.2(33)SXI4a
or later recommended
- Not supported in Release 12.2(33)SXJ and rebuilds
|
With Supervisor Engine 720 |
With Supervisor Engine 32 |
Wireless Services Modules
Wireless Services Module 2 (WiSM2)
Note ● Supervisor Engine 32 does not support WS-SVC-WISM2-K9.
- In a 13-slot chassis, WS-SVC-WISM2-K9 is supported only in slots 9 through 13 and does not power up in other slots.
- WS-SVC-WISM2-K9 runs its own software—See these publications:
http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html
- See the WS-SVC-WISM2-K9 software release notes for information about the minimum required WS-SVC-WISM-1-K9 software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Wireless Services Module 2 (WiSM2) |
With Supervisor Engine 720-10GE |
12.2(33)SXJ
|
With Supervisor Engine 720 |
Wireless Services Module (WiSM)
Note ● With releases earlier than Release 12.2(33)SXI, not supported in virtual switch mode.
- In a 13-slot chassis, WS-SVC-WISM-1-K9 is supported only in slots 9 through 13 and does not power up in other slots.
- WS-SVC-WISM-1-K9 runs its own software—See these publications:
http://www.cisco.com/en/US/products/ps6526/tsd_products_support_eol_model_home.html
- See the WS-SVC-WISM-1-K9 software release notes for information about the minimum required WS-SVC-WISM-1-K9 software version.
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Wireless Services Module (WiSM) |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF2
|
Fan Trays
Note Enter the show environment status | include fan command or the show environment cooling command to display information about the installed fan trays.
CISCO7606 Power Supplies
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
2700 W AC power supply |
12.2(18)SXE
|
|
2700 W DC power supply |
12.2(18)SXE
|
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
2700 W AC power supply |
12.2(18)SXE
|
|
2700 W DC power supply |
12.2(18)SXE
|
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
1,400 W AC power supply |
12.2(17a)SX
|
|
950 W AC power supply |
12.2(14)SX
|
|
950 W DC power supply |
12.2(14)SX
|
All Other Power Supplies
Note The power supplies in this section are not supported in these chassis:
- Catalyst 6503
- Catalyst 6503-E
- CISCO7603
- Catalyst 6504-E
- CISCO7604
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
8,700 W AC power supply |
12.2(18)SXF8
|
Note
- Limited to 4,500 W inthe WS-C6509-NEB-A chassis.
- Limited to 4,000 W in these chassis:
– WS-C6509 – WS-C6506 – WS-C6509-NEB
- WS-CAC-8700W-E supports a remote power cycling feature.
- See this publication for more information:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Chassis_Installation/Cat6500/6500_ins.html |
|
6,000 W DC power supply |
12.2(18)SXF13
12.2(33)SXH2
|
Note
- Limited to 4,500 W in the WS-C6509-NEB-A chassis.
- Limited to 4,000 W in these chassis:
– WS-C6509 – WS-C6506 – WS-C6509-NEB |
|
6,000 W AC power supply |
12.2(18)SXD
|
Note
- Limited to 4,500 W inthe WS-C6509-NEB-A chassis.
- Limited to 4,000 W in these chassis:
– WS-C6509 – WS-C6506 – WS-C6509-NEB |
|
4,000 W DC power supply |
12.2(14)SX
|
|
4,000 W AC power supply |
12.2(14)SX
|
|
3,000 W AC power supply |
12.2(17a)SX
|
Note
- Required with Supervisor Engine 720 or Supervisor Engine 720-10GE in WS-C6509-NEB or OSR7609.
- Included in the WS-6509-NEB-UPGRD= upgrade kit.
|
|
3,000 W AC power supply |
12.2(14)SX
|
|
2,500 W AC power supply |
12.2(14)SX
|
|
2,500 W DC power supply |
12.2(14)SX
|
13-Slot Chassis
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Catalyst 6513-E chassis:
- 13 slots
- 64 chassis MAC addresses
- These modules are supported only in slots 9 through 13 and do not power up in other slots:
– WS-X6700 series switching modules except WS-X6724-SFP – WS-X6816-GBIC switching modules – WS-SVC-WISM-1-K9 |
With Supervisor Engine 720-10GE |
12.2(33)SXI1
12.2(33)SXH2
|
With Supervisor Engine 720 |
12.2(33)SXI1
12.2(33)SXH2
12.2(18)SXF14
|
With Supervisor Engine 32 |
12.2(33)SXI1
12.2(33)SXH2
12.2(18)SXF14
|
|
Catalyst 6513 chassis:
- 13 slots
- 64 chassis MAC addresses
- Use with Supervisor Engine 720-10GE or Supervisor Engine 720 requires WS-C6K-13SLT-FAN2
- These modules are supported only in slots 9 through 13 and do not power up in other slots:
– WS-X6700 series switching modules except WS-X6724-SFP – WS-X6816-GBIC switching modules – WS-SVC-WISM-1-K9 |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
|
Cisco 7613 chassis:
- 13 slots
- 64 chassis MAC addresses
- Use with Supervisor Engine 720-10GE or Supervisor Engine 720 requires WS-C6K-13SLT-FAN2
- These modules are supported only in slots 9 through 13 and do not power up in other slots:
– WS-X6700 series switching modules – WS-X6816-GBIC switching modules – WS-SVC-WISM-1-K9 |
With Supervisor Engine 720-10GE (not supported in VSS mode). |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
9-Slot Chassis
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Catalyst 6509-V-E chassis:
- 9 vertical slots
- 64 chassis MAC addresses
- Required power supply:
– 2,500 W DC or higher – 3,000 W AC or higher |
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXF10
|
With Supervisor Engine 32 |
12.2(18)SXF10
|
|
Catalyst 6509-E chassis:
- 9 horizontal slots
- Chassis MAC addresses:
– Before April 2009—1024 chassis MAC addresses – Starting in April 2009—64 chassis MAC addresses Note Chassis with 64 MAC addresses automatically enable the Extended System ID feature, which is enabled with the spanning-tree extend system-id command. You cannot disable the extended-system ID in chassis that support 64 MAC addresses. The Extended System ID feature might already be enabled in your network, because it is required to support both extended-range VLANs and any chassis with 64 MAC addresses. Enabling the extended system ID feature for the first time updates the bridge IDs of all active STP instances, which might change the spanning tree topology.
- Requires 2,500 W or higher power supply
- With releases earlier than Release 12.2(18)SXD, WS-CAC-6000W is limited to 4,000 W in WS-C6509-E
|
With Supervisor Engine 720-10GE |
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(14)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Catalyst 6509 chassis:
- 9 horizontal slots
- 1024 chassis MAC addresses
- Use with Supervisor Engine 720-10GE, Supervisor Engine 720, or Supervisor Engine 32 requires WS-C6K-9SLOT-FAN2
- WS-CAC-6000W is limited to 4,000 W in WS-C6509
|
With Supervisor Engine 720-10GE |
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(14)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Catalyst 6509-NEB chassis
|
With Supervisor Engine 720-10GE |
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(14)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Catalyst 6509-NEB chassis:
- 9 vertical slots
- 1024 chassis MAC addresses
- Requires the WS-6509-NEB-UPGRD= upgrade kit—refer to this publication:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16162.html
- Does not support WS-X6716-10T-3C or WS-X6716-10T-3CXL.
|
With Supervisor Engine 720 |
12.2(17a)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Cisco 7609 chassis
- 9 vertical slots
- 64 chassis MAC addresses
|
With Supervisor Engine 720-10GE (Not supported in VSS mode) |
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(14)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Cisco 7609 chassis:
- 9 vertical slots
- 1024 chassis MAC addresses
- Requires the WS-6509-NEB-UPGRD= upgrade kit—refer to this publication:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16162.html |
With Supervisor Engine 720 |
12.2(17a)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
6-Slot Chassis
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Catalyst 6506 chassis:
- 6 slots
- Chassis MAC addresses:
– Before April 2009—1024 chassis MAC addresses – Starting in April 2009—64 chassis MAC addresses Note Chassis with 64 MAC addresses automatically enable the Extended System ID feature, which is enabled with the spanning-tree extend system-id command. You cannot disable the extended-system ID in chassis that support 64 MAC addresses. The Extended System ID feature might already be enabled in your network, because it is required to support both extended-range VLANs and any chassis with 64 MAC addresses. Enabling the extended system ID feature for the first time updates the bridge IDs of all active STP instances, which might change the spanning tree topology.
- Requires 2,500 W or higher power supply
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
|
Catalyst 6506 chassis:
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
|
Cisco 7606 chassis:
|
With Supervisor Engine 720 |
12.2(14)SX
|
With Supervisor Engine 32 |
12.2(18)SXF
|
4-Slot Chassis
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
Catalyst 6504-E chassis:
- 4 slots
- 64 chassis MAC addresses
|
With Supervisor Engine 720-10GE |
12.2(33)SXH
|
With Supervisor Engine 720 |
12.2(18)SXE
|
With Supervisor Engine 32 |
12.2(18)SXF
|
|
Cisco 7604 chassis:
- 4 slots
- 64 chassis MAC addresses
|
With Supervisor Engine 720-10GE (not supported in VSS mode) |
12.2(33)SXH
|
With Supervisor Engine 720: |
12.2(18)SXE
|
With Supervisor Engine 32 |
12.2(18)SXF
|
3-Slot Chassis
(append “=” for spares)
|
|
Minimum
Software
Versions
|
|
- 3 slots
- 64 chassis MAC addresses
|
With Supervisor Engine 720-10GE |
12.2(33)SXH |
With Supervisor Engine 720 |
12.2(14)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Catalyst 6503 chassis:
- 3 slots
- 64 chassis MAC addresses
- Requires FAN-MOD-3HS
- Does not support:
– WS-X6700 series switching modules – WS-X6816-GBIC switching modules – Supervisor Engine 720-10GE |
With Supervisor Engine 720 |
12.2(14)SX |
With Supervisor Engine 32 |
12.2(18)SXF |
|
Cisco 7603 chassis:
- 3 slots
- 64 chassis MAC addresses
- Use with Supervisor Engine 720-10GE or Supervisor Engine 720 requires FAN-MOD-3HS
- Does not support:
– WS-X6700 series switching modules – WS-X6816-GBIC switching modules – Supervisor Engine 720-10GE – Supervisor Engine 32 |
With Supervisor Engine 720 |
12.2(14)SX |
Cisco ME 6500 Series Ethernet Switches (ME6524)
Cisco ME 6500 Series Ethernet Switches Restrictions
Cisco ME 6500 Series Ethernet switches cannot support these software features and commands:
- Cisco ME 6500 Series Ethernet switches are not supported in Release 12.2(33)SXJ and later releases. Support continues in Release 12.2(33)SXI and rebuilds.
- Egress multicast replication
- Multicast replication mode detection
- Fabric configuration commands
- RPR and SSO redundancy
- VLAN translation
Cisco ME 6500 Series Ethernet Switches Features
(append “=” for spares)
|
|
|
ME-C6524GS-8S
ME-C6524GT-8S
|
Cisco ME 6500 Series Ethernet switches:
– For Cisco IOS images, 256-MB DRAM ( some images require more DRAM) – For Cisco IOS modularity images, with releases earlier than Release 12.2(33)SXH3, 256-MB DRAM ( some images require more DRAM) – For Cisco IOS modularity images, with Release 12.2(33)SXH3 and later releases, 512-MB DRAM required ( some images require more DRAM) – 128-MB bootflash (sup-bootflash: ; from ROMMON, it is bootflash:)
- Route processor (RP)—Multilayer Switch Feature Card 2A (MSFC2A):
– 512-MB DRAM ( some images require more DRAM) – 64-MB bootflash (bootflash:)
- Policy Feature Card 3C (PFC3C)
– See the “Policy Feature Cards” section – ME 6500 switches always operate in PFC3C mode. Enter the show platform hardware pfc mode command to display the PFC3 mode.
- Fan tray: FAN-C6524
- Power supplies (can be used together):
– PWR-400W-DC – PWR-400W-AC
- 64 chassis MAC addresses
- One external CompactFlash Type II slot (disk0: ; supports CompactFlash Type II Flash PC cards sold by Cisco Systems, Inc., for use in Cisco ME 6500 Series Ethernet switches)
- Eight SFP ports:
– Requires Small Form-Factor Pluggable (SFP) Modules – 1 port group: ports 25–32 – QoS port architecture (Rx/Tx): 2q8t/1p3q8t
– 24 SFP ports (requires Small Form-Factor Pluggable (SFP) Modules) – 4 port groups: ports 1–6, 7–12, 13–18, 19–24 – QoS port architecture (Rx/Tx): 1q2t/1p3q8t
– 24 10/100/1000 Mbps RJ-45 Ethernet ports – 4 port groups: ports 1–6, 7–12, 13–18, 19–24 – QoS port architecture (Rx/Tx): 1q2t/1p3q8t |
12.2(33)SXH
|
Note See this publication for Cisco ME 6500 Series Ethernet switch hardware information: http://www.cisco.com/en/US/products/ps6845/tsd_products_support_eol_series_home.html |
Unsupported Hardware
Note ● See the “Supervisor Engine 32 (CAT6000-SUP32/MSFC2A)” section for information about hardware that is not supported with the Supervisor Engine 32.
- See the Release Notes for Cisco IOS Release 12.2SXF and Rebuilds publication for information about support in earlier releases:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/release/notes/OL_4164.html
Release 12.2(33)SXH and later releases do not support the following hardware:
- Supervisor Engine 1 (WS-X6K-S1A-MSFC2, WS-X6K-SUP1A-MSFC)
- Supervisor Engine 2 (WS-X6K-S2U-MSFC2, WS-X6K-S2-MSFC2)
- WS-F6K-DFC distributed forwarding card (DFC)
- Optical Services Modules (OSMs)
- These service modules:
– WS-X6381-IDS Intrusion Detection System (IDS) Module (WS-SVC-IDSM2-K9 is supported)
– WS-X6380-NAM Network Analysis Module (NAM; WS-SVC-NAM-2 and WS-SVC-NAM-1 are supported)
– WS-SVC-AON-1-K9 Application-Oriented Networking (AON) Module
– WS-SVC-CSG-1 Content Services Gateway (CSG) Module
– WS-SVC-IPSEC-1 IPsec VPN Acceleration Services Module
– WS-SVC-MWAM-1 Multi-Processor WAN Application Module
– WS-SVC-PSD-1 Persistent Storage Device Module
– WS-SVC-WEBVPN-K9 WebVPN Services Module
– WS-SVC-WLAN-1-K9 Wireless LAN service module
- Release 12.2(33)SXI and rebuilds support the 7600-SIP-600. Release 12.2(33)SXH and rebuilds do not support the 7600-SIP-600 and these SPAs:
– SPA-10X1GE 10-port Gigabit Ethernet SPA, SFP Optics
– SPA-5X1GE 5-port Gigabit Ethernet SPA, SFP Optics
– SPA-1XTENGE-XFP 1-port 10-Gigabit Ethernet SPA, LANPHY XFP Optics
– SPA-OC192POS-VSR 1-port OC-192c/STM-64 POS/RPR SPA, VSR-1
– SPA-OC192POS-LR 1-port OC-192c/STM-64 POS/RPR SPA, SM-LR
– SPA-OC192POS-XFP 1-port OC-192c/STM-64 POS/RPR SPA, XFP Optics
– SPA-OC192POS-VSR 1-port OC-192c/STM-64 POS/RPR SPA, VSR-1
- WS-X6182-2PA FlexWAN Module
- These Ethernet Switching Modules:
– WS-X6024-10FL-MT 24-port 10BASE-FL MT-RJ
– WS-X6248A-TEL 48-port 10/100TX RJ-21
– WS-X6248-RJ-45 48-port 10/100TX RJ-45
– WS-X6248-TEL 48-port 10/100TX RJ-21
– WS-X6324-100FX-SM 24-port 100FX Ethernet
– WS-X6224-100FX-MT 24-port 100FX Ethernet Multimode MT-RJ
– WS-X6316-GE-TX 16-port Gigabit Ethernet RJ-45
– WS-X6416-GE-MT 16-Port Gigabit Ethernet MT-RJ
- WS-CAC-1000W power supply
- WS-CAC-1300W power supply
- WS-CDC-1300W power supply
- These fan trays:
– FAN-MOD-3
– FAN-MOD-6
– WS-C6K-6SLOT-FAN
– WS-C6509-NEB-FAN
– WS-C6K-9SLOT-FAN
– WS-C6K-13SLT-FAN
- With a Supervisor Engine 720, WS-X6516-GBIC hardware revisions 5.0 through 5.4 with a DFC3 installed.
Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:
– Lower than 5.0
– 5.5 and higher
With a Supervisor Engine 720 and a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.3 do not power up. Without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.
See external field notice 24494 for more information:
http://www.cisco.com/en/US/ts/fn/200/fn24494.html
- WS-X6624-FXS, WS-X6608-T1, and WS-X6608-E1 voice modules
- WS-X6101-OC12-MMF and WS-X6101-OC12-SMF ATM LANE modules
- WS-X6302-MSM Multilayer Switch Module
- Catalyst 6000 series chassis
Unsupported modules remain powered down if detected and do not affect system behavior.