-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

5-Notice

0

-

-

-

-

5-Notice

-

A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table.

SISF_COMP_NAME

-

-

5-Notice

-

-

ipv6

"A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests"

-

5-Notice

-

Two devices with random MACs generated the same MAC address. \n\ The second device has been rejected.

SISF_COMP_NAME

"The second device will need to regenerate its random MAC."

-

6-Information

authentication packet received on sessions with invalid config

authentication only supported for multihop BFD sessions

bfd

LOG_STD_ACTION

-

6-Information

packet received failed authentication

packet authentication failed

bfd

LOG_STD_ACTION

-

6-Information

Could not allocate valid session handle

session handle not allocated

bfd

LOG_STD_ACTION

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

5-Notice

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

5-Notice

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

-

3-Error

fmt { \ size_t len = strlen

-

-

-

-

3-Error

fmt { \ size_t len = strlen

-

-

-

-

3-Error

fmt printf

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

3-Error

fmt \ syslog_

-

-

-

-

3-Error

\ fmt

-

-

-

-

3-Error

-

BULKSTAT Service Enabled

SRVNAME_BULKSTAT

SYSLOGDOC_NO_ACTION

-

3-Error

-

BULKSTAT Service Disabled

SRVNAME_BULKSTAT

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CORE Service nabled

SRVNAME_DCM_CORE

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CORE Service Disabled

SRVNAME_DCM_CORE

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CLI_DP Service nabled

SRVNAME_DCM_CLI_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CLI_DP Service Disabled

SRVNAME_DCM_CLI_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_SNMP_DP Service nabled

SRVNAME_DCM_SNMP_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_SNMP_DP Service Disabled

SRVNAME_DCM_SNMP_DP

SYSLOGDOC_NO_ACTION

-

3-Error

fmt \local_errmsg_t msg_ ## fac ## _ ## name = { #name

-

-

-

-

3-Error

fmt \extern C local_errmsg_t msg_ ## fac ## _ ## name

-

-

-

-

6-Information

authentication packet received on sessions with invalid config

authentication only supported for multihop BFD sessions

bfd

LOG_STD_ACTION

-

6-Information

packet received failed authentication

packet authentication failed

bfd

LOG_STD_ACTION

-

6-Information

Could not allocate valid session handle

session handle not allocated

bfd

LOG_STD_ACTION

-

5-Notice

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

5-Notice

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

3-Error

fmt \ syslog_

-

-

-

-

3-Error

\ fmt

-

-

-

-

3-Error

-

BULKSTAT Service Enabled

SRVNAME_BULKSTAT

SYSLOGDOC_NO_ACTION

-

3-Error

-

BULKSTAT Service Disabled

SRVNAME_BULKSTAT

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CORE Service nabled

SRVNAME_DCM_CORE

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CORE Service Disabled

SRVNAME_DCM_CORE

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CLI_DP Service nabled

SRVNAME_DCM_CLI_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CLI_DP Service Disabled

SRVNAME_DCM_CLI_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_SNMP_DP Service nabled

SRVNAME_DCM_SNMP_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_SNMP_DP Service Disabled

SRVNAME_DCM_SNMP_DP

SYSLOGDOC_NO_ACTION

-

3-Error

0

-

-

-

-

3-Error

-

A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table.

SISF_COMP_NAME

-

-

3-Error

-

-

ipv6

"A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests"

-

3-Error

-

Two devices with random MACs generated the same MAC address. \n\ The second device has been rejected.

SISF_COMP_NAME

"The second device will need to regenerate its random MAC."

-

3-Error

fmt { \ size_t len = strlen

-

-

-

-

3-Error

fmt { \ size_t len = strlen

-

-

-

-

3-Error

fmt printf

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

5-Notice

fmt \local_errmsg_t msg_ ## fac ## _ ## name = { #name

-

-

-

-

5-Notice

fmt \extern C local_errmsg_t msg_ ## fac ## _ ## name

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

-

-

-

-

-

-

4-Warning

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

-

4-Warning

fmt \static message_stats_ptr fac ## _ ## name ## _stat_redir_ptr __crb_sysrgn

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

-

3-Error

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

3-Error

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

_NEW_APP_NAME_-3-MSG_ERR

3-Error

[chars]

Error Messages

pagent

"try debug command"

_NEW_APP_NAME_-6-MSG_INF

6-Information

[chars]

Program information

-

-

_NEW_APP_NAME_-7-MSG_DBG

7-Debug

[chars]

Debug Messages

-

-

AAA_CACHE-3-NULL_TREE_PERIODIC_PROC

3-Error

Cache Tree pointer is of null value

The cache tree pointer is of null value.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAA_CACHE-3-NULL_TREE_PERIODIC_PROC

3-Error

Cache Tree pointer is of null value

The cache tree pointer is of null value.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-5-LOCAL_USER_BLOCKED

5-Notice

User [chars] blocked for login till [chars]

User blocked since the number of authentication failures in the watch time exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-LOCAL_USER_BLOCKED

5-Notice

User [chars] blocked for login till [chars]

User blocked since the number of authentication failures in the watch time exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ this is only a warning

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ this is only a warning

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ this is only a warning

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ please choose another name

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-6-ACCTLOCAL

6-Information

Username: [chars] Privilege level: [dec] Command: [chars]

AAA local accounting log message

aaa

"This information is to store buffered logs" "locally and send to SYSLOG server"

AAAA-6-ACCTLOCAL

6-Information

Username: [chars] Privilege level: [dec] Command: [chars]

AAA local accounting log message

aaa

"This information is to store buffered logs" "locally and send to SYSLOG server"

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AC-3-AC_SANITY

3-Error

[chars]

A unexpected sanity check failed during Attachment Circuit processing.

ac

LOG_STD_ACTION

AC-3-AC_SANITY

3-Error

[chars]

A unexpected sanity check failed during Attachment Circuit processing.

ac

LOG_STD_ACTION

AC-3-AC_WS_REGISTER

3-Error

L2VPN WS registration failed for [chars]

An error was encountered when attempting to register the specified Attachment Circuit type with the Layer 2 Virtual Private Network Wire Service facility.

ac

LOG_STD_ACTION

AC-3-AC_WS_REGISTER

3-Error

L2VPN WS registration failed for [chars]

An error was encountered when attempting to register the specified Attachment Circuit type with the Layer 2 Virtual Private Network Wire Service facility.

ac

LOG_STD_ACTION

AC-3-ACMGR_INVALID_HDL

3-Error

Received invalid [chars] handle

Attachment Circuit Manager receives invalid handle.

ac

LOG_STD_ACTION

AC-3-ACMGR_INVALID_HDL

3-Error

Received invalid [chars] handle

Attachment Circuit Manager receives invalid handle.

ac

LOG_STD_ACTION

AC-3-ACMGR_INVALID_MSG

3-Error

Received [chars]

Attachment Circuit Manager receives invalid message.

ac

LOG_STD_ACTION

AC-3-ACMGR_INVALID_MSG

3-Error

Received [chars]

Attachment Circuit Manager receives invalid message.

ac

LOG_STD_ACTION

AC-3-ACMGR_MISSED_CIRCUIT

3-Error

Circuit info missing in [chars] message.

AC Manager received message with missing circuit info

ac

LOG_STD_ACTION

AC-3-ACMGR_MISSED_CIRCUIT

3-Error

Circuit info missing in [chars] message.

AC Manager received message with missing circuit info

ac

LOG_STD_ACTION

AC-3-ACMGR_XDM_CREATE

3-Error

Failed to create XDM - rc [dec]

Attachment Circuit Manager was unable to create a Dispatch Manager instance for event handling.

ac

LOG_STD_ACTION

AC-3-ACMGR_XDM_CREATE

3-Error

Failed to create XDM - rc [dec]

Attachment Circuit Manager was unable to create a Dispatch Manager instance for event handling.

ac

LOG_STD_ACTION

AC-3-L2SS_BAD_HANDLE

3-Error

Corrupted L2SS handle [[hec]].

An internal L2SS Manager occurred.

ac

LOG_STD_ACTION

AC-3-L2SS_BAD_HANDLE

3-Error

Corrupted L2SS handle [[hec]].

An internal L2SS Manager occurred.

ac

LOG_STD_ACTION

AC-3-L2SS_NULL_CONTEXT

3-Error

Encountered a NULL context in [chars]

Encountered a NULL context in L2SS Manager.

ac

LOG_STD_ACTION

AC-3-L2SS_NULL_CONTEXT

3-Error

Encountered a NULL context in [chars]

Encountered a NULL context in L2SS Manager.

ac

LOG_STD_ACTION

AC-3-L2SS_UNEXPECTED

3-Error

Received unexpected [chars] message

L2SS received unexpected message.

ac

LOG_STD_ACTION

AC-3-L2SS_UNEXPECTED

3-Error

Received unexpected [chars] message

L2SS received unexpected message.

ac

LOG_STD_ACTION

AC-3-L2SS_WRONG_KEYS

3-Error

Wrong set of keys in [chars] message

SIP sends a wrong set of keys to L2SS Manager.

ac

LOG_STD_ACTION

AC-3-L2SS_WRONG_KEYS

3-Error

Wrong set of keys in [chars] message

SIP sends a wrong set of keys to L2SS Manager.

ac

LOG_STD_ACTION

ACCESS_IE-3-INVALID_HANDLE

3-Error

Caller passed in invalid handle - traceback to follow.

An invalid handle was encountered in the Access IE library.

-

LOG_STD_ACTION

ACCESS_SESSION-3-TRACE_INIT_FAIL

3-Error

Initialization failed with code: [dec]

Failed to initialize access-session trace.

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_INIT_FAIL

3-Error

Initialization failed with code: [dec]

Failed to initialize access-session trace.

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_INIT_FAIL

3-Error

Initialization failed with code: [dec]

Failed to initialize access-session trace.

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_REG_FAIL

3-Error

Component [chars] registration failed. Error code: [dec]

Component failed to register with access-session trace

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_REG_FAIL

3-Error

Component [chars] registration failed. Error code: [dec]

Component failed to register with access-session trace

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_REG_FAIL

3-Error

Component [chars] registration failed. Error code: [dec]

Component failed to register with access-session trace

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_TUNNEL_ISSU-3-BUFFER

3-Error

ACCESS_TUNNEL ISSU client failed to get buffer for message error [dec]

ACCESS_TUNNEL ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can not send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

accsw-p-securefab

"show logging and show checkpoint client"

ACCESS_TUNNEL_ISSU-3-CAP_INVALID_SIZE

3-Error

ACCESS_TUNNEL ISSU client capability list is empty.

The ACCESS_TUNNEL ISSU client capability exchange list size\n\ is invalid.

accsw-p-securefab

"show issu capability entries <Client_ID>"

ACCESS_TUNNEL_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

ACCESS_TUNNEL ISSU client capability exchange result incompatible.

The ACCESS_TUNNEL ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

accsw-p-securefab

"show issu negotiated capability <Session_ID>"

ACCESS_TUNNEL_ISSU-3-CAPABILITY

3-Error

ACCESS_TUNNEL ISSU client [chars]

ACCESS_TUNNEL ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

accsw-p-securefab

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

ACCESS_TUNNEL_ISSU-3-INIT

3-Error

ACCESS_TUNNEL ISSU client initialization failed at [chars] error [chars]

ACCESS_TUNNEL ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

accsw-p-securefab

LOG_STD_SH_TECH_ACTION

ACCESS_TUNNEL_ISSU-3-MSG_NOT_OK

3-Error

ACCESS_TUNNEL ISSU client message [dec] is not compatible

ACCESS_TUNNEL ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can not be processed by this unit

accsw-p-securefab

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

ACCESS_TUNNEL_ISSU-3-MSG_SIZE

3-Error

ACCESS_TUNNEL ISSU client failed to get the message size for message [dec]

ACCESS_TUNNEL ISSU client failed to calculate message size\n\ for the message specified. The ACCESS_TUNNEL ISSU client will not\n\ be able to send message to the standby unit.

accsw-p-securefab

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

ACCESS_TUNNEL_ISSU-3-POLICY

3-Error

ACCESS_TUNNEL ISSU client message type [dec] is [chars]

ACCESS_TUNNEL ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

accsw-p-securefab

"show issu session <client_id>"

ACCESS_TUNNEL_ISSU-3-SEND_FAILED

3-Error

ACCESS_TUNNEL ISSU client failed to send a negotiation message error [dec]

ACCESS_TUNNEL ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the \n\ negotiation the standby unit can not be brought up.

accsw-p-securefab

"show logging and show checkpoint client"

ACCESS_TUNNEL_ISSU-3-SESSION

3-Error

ACCESS_TUNNEL ISSU client [chars]

ACCESS_TUNNEL ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

accsw-p-securefab

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

ACCESS_TUNNEL_ISSU-3-SESSION_UNREGISTRY

3-Error

ACCESS_TUNNEL ISSU client failed to unregister session information. Error: [dec] [chars]

The ACCESS_TUNNEL ISSU client failed to unregister session information.

accsw-p-securefab

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ACCESS_TUNNEL_ISSU-3-TRANSFORM

3-Error

ACCESS_TUNNEL ISSU client [chars] transform failed error [chars]

ACCESS_TUNNEL ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the ACCESS_TUNNEL state will not\n\ be indentical with the active unit.

accsw-p-securefab

"show issu session <client_id> and \n\ show issu negotiated version <session_id>"

ACE-2-CRYPTOENGERR

2-Critical

Crypto engine error: [chars] [dec]

A crypto engine operation did not complete. This error condition can indicate that the crypto engine cannot bind or unbind an interface to a crypto engine. It can also indicate that the crypto engine cannot query an interface ID.

-

"Remove the cryptomap set from the interface by issuing " "<CmdBold>no crypto map<noCmdBold> command. Then reattach the cryptomap " "set to the interface using <CmdBold>crypto map<noCmdBold> command. " "Although removing and reattaching the crypto map might fix the " "cryptographic engine operation failure report the failure to your " "technical support representative along with the sequence of commands " "that lead to the failure".

ACE-2-INTTABOPERR

2-Critical

Internal [chars] table error: [chars]

Internal table operation fails. This means the state of the module is mostly like inconsistent.

iosxe-ipsec

"Contact your technical support representative"

ACE-3-BOOTMSGERR

3-Error

[chars]: boot error: [chars]

The ACE completed booting but with an error status code. ACE will not operate and it will not register with the crypto subsystem.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-CEAL_REGISTRATION

3-Error

ACE [chars] failed to register.

The ACE failed to register with CEAL

iosxe-ipsec

"Reset the hw module"

ACE-3-CRASHDUMPERR

3-Error

[chars]: crashdump retrieval error: [chars] [chars]

An error occurred during crashdump file retrieval from ACE.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-CRASHDUMPSTART

3-Error

[chars]: crashdump retrieval initiated to file [chars]

The ACE crashed and was rebooted. Upon reboot a crashdump file was detected and uploaded to the sup-bootflash filesystem.

-

"Report the crash and transfer the crashdump file to your technical" "support representative."

ACE-3-HAPITRUNC

3-Error

[chars]: Received truncated HAPI message tlen=[dec] actual=[dec]

An IPsec packet was unexpectedly forwarded to the RP

iosxe-ipsec

"If this message was seen in the context of the router booting " "enabling the hardware crypto accelerator then this message is normal " "and can be safely ignored. " "Otherwise please copy the error message exactly as it appears " "and report it to your technical support representative."

ACE-3-INITFAIL

3-Error

[chars]: initialization failed [chars]

An error occured in the indicated control transaction.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-INVTID

3-Error

[chars]: [chars] of invalid [chars] trans id [dec]

An invalid transaction ID of for the indicated transaction\n\ type was encountered

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-NOENGINESLOT

3-Error

Interface [chars] has no crypto engine slot

An IKE SA was requested for a given interface but no crypto engine slot was assigned to that interface

iosxe-ipsec

"Configure the interface in question with the" " `crypto engine [sub]slot' command"

ACE-3-NOMORETID

3-Error

[chars]: out of [chars] transactions

Transaction pool for the indicated transaction type was\n\ exhausted.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-OUTOFID_RL

3-Error

Too many [chars] IDs in the system. Cannot allocate a new one

All the IDs of the specified type are in use

iosxe-ipsec

"Reduce the traffic load number of IPSec tunnels and/or frequency of re-key." "If this message was seen under light loading conditions then" "copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-OUTOFRES

3-Error

Too many [chars] in the system. Cannot allocate a new one

All VPN-accelerator resources of a particular are in used and thus this allocation request fails.

iosxe-ipsec

"Remove the cryptomap set from the interface. " "Reduce the number of that resource in the " "system. For ACL reduce the number of ACL " "permit ACE in the system. For cryptomap reduce the" "number of cryptomaps in the system. For SPD and " "SPD map reduce the number of interface with " "cryptomap set attached."

ACE-4-BV_IDMGR_DESTROY

4-Warning

ACE failed to destroy [chars] ID manager. Leaking memory.

The ACE failed to destroy memory space for ID management.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-6-BOOTMSGINFO

6-Information

[chars]: boot info: [chars]

The ACE completed booting but with a non-zero informational status code. This does not indicate an error and ACE will run normally.

-

"No action is necessary."

ACE-6-CRASHDUMPEND

6-Information

[chars]: crashdump retrieval complete

The ACE crashed and was rebooted. Upon reboot a crashdump file was detected and uploaded to the sup-bootflash filesystem.

-

"Report the crash and transfer the crashdump file to your technical" "support representative."

ACE-6-INFO

6-Information

[chars]: [chars]

This is informational message from ACE

iosxe-ipsec

"This is informational message from ACE. This occurs " "in normal operation."

ACE-6-SWITCHOVER

6-Information

VPN-SM switchover: [dec]/[dec] has been [chars] [dec]/[dec]

An negative acknowledge occured in the indicated control transaction.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACL1-5-LDP

5-Notice

5*ERRMSG_LIMIT_SLOW

-

-

-

ACL1-5-LDP

5-Notice

5*ERRMSG_LIMIT_SLOW

-

-

-

ACL-3-UNEXPECTED_PKT_TYPE

3-Error

type [dec] int [dec] [chars]put

ACL logging has encountered unexpected pkt type.

cpp-ucode

LOG_STD_ACTION

ACL-3-UNEXPECTED_STATE

3-Error

type [dec] int [chars] [chars]put w0: 0x%p w1: 0x[hec]

An error has occurred in the setup of ACL hardware.

cpp-ucode

LOG_STD_ACTION

ACL-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

ACL-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

ACLMERGE-3-CUDDERROR

3-Error

A CUDD Library error was detected in [chars]

An error was detected by the CUDD Library the ACL-Merge for this invokation has failed. This could result in more traffic being switched by software. The effect of this could be lower performance for the interface for which the merge failed.

aclmerge

"Copy and save this message. Report this to Engineering along with the ACL configuration of this device. Use Topic to search for a similar DDTS. If none found write a DDTS for this problem"

ACLMERGE-3-CUDDWARN

3-Error

A CUDD Library warning message for interest in this event in [chars]

Debug message only. No action required

aclmerge

"Copy and save this message. Report this to Engineering along with the ACL configuration of the device. This is just a debug message of interest to engineering to investigate the case why this happened"

ACLMGR-2-NOMAP

2-Critical

Cannot create ACL Manager data structures for VLAN Map [chars]

The ACL Manager could not allocate the data structures needed to describe a VLAN Map in a form that can be loaded into hardware. Probably caused by lack of free memory.

firmware

LOG_STD_REDUCE_ACTION

ACLMGR-2-NOVLB

2-Critical

Cannot create memory block for VLAN [dec]

The ACL Manager was unable to save per-VLAN information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly.

firmware

"Use a less complicated configuration that " "requires less memory."

ACLMGR-2-NOVMR

2-Critical

Cannot generate hardware representation of access list [chars]

There were insufficient resources available for generating a hardware representation of the access list. Either lack of available logical operation units or lack of memory can cause this problem. Logical operation units are needed when a match on TCP flags is specified or when any test other than eq that is: ne gt lt or range is

firmware

"Modify the ACL configuration to use fewer resources."

ACLMGR-3-AUGMENTFAIL

3-Error

Augmenting of access-map [chars] on [chars] label [dec] failed

The system ran out of CPU DRAM when attempting to merge internally required elements with the configured access maps.

firmware

LOG_STD_REDUCE_ACTION

ACLMGR-3-FEATUREMISMATCH

3-Error

[chars] can not be supported with the image running on switch-[dec]

A feature has been configured on the stack but can not be supported on one or more switches in the stack. This feature will continue to work on the rest of the switches that support it but will not be applied to the switches that can not support it. All other features continue to work as expected on the stack.

firmware

"Upgrade the software running on switches that " "can not support this feature. Upgrade to a " "software version that supports this feature."

ACLMGR-3-IECPORTLABELERROR

3-Error

ACL labels are out-of-sync on interface [chars] label [dec] is not available on asic [dec]

An internal software error has occurred.

firmware

LOG_STD_ACTION

ACLMGR-3-INSERTFAIL

3-Error

Insert of access-map [chars] #[dec] into [chars] label [dec] failed

The system ran out of CPU DRAM when trying to merge sections of an access map.

firmware

LOG_STD_REDUCE_ACTION

ACLMGR-3-INTTABLE

3-Error

Not in truth table: VLMAP [dec] RACL [dec] Rtprot [dec] Mcb [dec] Feat [dec]

An unrecoverable software error occurred while trying to merge the configured input features.

firmware

"show running-config"

ACLMGR-3-INVALIDL4PORTINDEX

3-Error

Invalid L4 port array index while processing [chars]

ACL Manager module received invalid value for L4 port array index. The problem can be due to memory corruption or bad system memory.

firmware

NACL_L4OP_ERROR

ACLMGR-3-INVALIDPARAM

3-Error

Invalid [chars] [dec] encountered

ACL Manager has encountered an invalid parameter value.

firmware

"show running-config"

ACLMGR-3-MAXRECURSION

3-Error

Too many [dec] levels of recursion while merging ACLs code [dec].

The configuration is too complicated for the platform specific ACL merge code to support. Most likely cause is including too many separate access lists in a single VLAN map or policy map.

firmware

"Reduce the number IP or MAC access lists" " considered separately in any one VLAN or policy"

ACLMGR-3-MERGEFAIL

3-Error

[chars] ACL merge error [dec] [chars] on [chars] label [dec]

The ACL Manager was unable to complete the merge of the configured features into a form suitable for loading into the hardware. Packets potentially affected by this feature will be sent to the CPU for processing instead. The most likely cause is specifying an ACL that is too large or too complex for the system to handle.

firmware

"Try specifying a smaller and less complicated " "configuration."

ACLMGR-3-NOLABEL

3-Error

Cannot allocate [chars] label for vlan-id [dec]

The ACL Manager was unable to allocate a label for the features on this interface. This means that the hardware cannot be programmed to implement the features and packets for this interface will be filtered in software. There is a limit of 256 labels per direction.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible."

ACLMGR-3-OUTTTABLE

3-Error

Not in truth table: RACL [dec] VLMAP [dec]

An unrecoverable software error occurred while trying to merge the configured output features.

firmware

"show running-config"

ACLMGR-3-PACLTTABLE

3-Error

Not in truth table: IPSrcGrd [dec] PACL [dec] Rtprot [dec]

An unrecoverable software error occurred while trying to merge the configured port acl features.

firmware

"show running-config"

ACLMGR-3-QOSTTABLE

3-Error

Not in truth table: ACL [dec] in map action [dec]

A software error occurred while trying to merge a QoS Policy Map

firmware

"show running-config"

ACLMGR-3-UNKNOWNACTION

3-Error

Unknown VMR access group action 0x[hec]

An internal software error has occurred.

firmware

LOG_STD_ACTION

ACLMGR-3-UNKNOWNL4OPERATION

3-Error

Unknown L4 operation 0x[hec]

ACL Manager module received invalid value for L4 operation. The problem can be due to memory corruption or bad system memory.

firmware

NACL_L4OP_ERROR

ACLMGR-4-ACLTCAMFULL

4-Warning

[chars]ACL TCAM Full. Software Forwarding packets on [chars] label [dec] on [chars] [chars]

The ACL configuration is too large to fit in the platform -specific ACL TCAM table.

firmware

"Simplify the ACLs applied to interfaces or reduce" " their number."

ACLMGR-4-ACLTCAMFULL

4-Warning

ACL TCAM Full. [chars] [chars] [chars] [chars]

The ACL configuration is too large to fit in the platform -specific ACL TCAM table.

firmware

"Simplify the ACLs applied to interfaces or reduce" " their number."

ACLMGR-4-RELOADED

4-Warning

Reloading [chars] [chars] label [dec] [chars] [chars]feature

The ACL Manager was able to fit more of the configured features on this label into the hardware. One or more features had previously been unloaded because of lack of space.

firmware

LOG_STD_NO_ACTION

ACLMGR-4-RELOADEDFSPAN

4-Warning

Reloading [chars] session [dec] [chars] feature

The ACL Manager was able to fit more of the configured Flow based SPAN features on this session into the hardware. One or more features had previously been unloaded because of lack of space.

firmware

LOG_STD_NO_ACTION

ACLMGR-4-UNLOADING

4-Warning

Unloading [chars] [chars] label [dec] [chars] [chars]feature

The ACL Manager was unable to fit the complete configuration into the hardware so some features will have to be applied in software. This prevents some or all of the packets in a VLAN/port from being forwarded in hardware and requires them to be forwarded by the CPU. Multicast packets may be dropped entirely instead of being forwarded.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible."

ACLMGR-4-UNLOADINGFSPAN

4-Warning

Unloading [chars] session [dec] [chars] feature

The ACL Manager was unable to fit the complete Flow based SPAN configuration into the hardware so this feature has been temporarily disabled for the given session.

firmware

"Allocate more space to the ACL section of the " "TCAM by choosing an SDM template with more ACL " "TCAM space and reboot the switch. You may also " "use a simpler ACL configuration and/or use the " "same ACLs on multiple interfaces if possible."

ACR-1-ISSU_NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

ACR_DDTS_COMPONENT

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

ACR-3- ACRIFADD

3-Error

[chars] interface add failed for ACR group [dec].

Addition of interface to ACR group failed

ACR_DDTS_COMPONENT

"Get the output of \"show acr all \" immediately after this error." "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRIFDEL

3-Error

[chars] interface del failed for ACR group [dec].

Delete of interface from ACR group failed

ACR_DDTS_COMPONENT

"Get the output of \"show acr all \" immediately after this error." "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRPVCDISABLE

3-Error

PVC Disable failed for VCD= [dec] on [chars] interface of ACR interface [chars].

PVC disable failed on ACR physical interface.

ACR_DDTS_COMPONENT

"Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRVPDISABLE

3-Error

VP Disable failed for VPI= [dec] on [chars] interface of ACR interface [chars].

VP disable failed on ACR physical interface.

ACR_DDTS_COMPONENT

"Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRVPENABLE

3-Error

VP Enable failed for VPI= [dec] on [chars] interface of ACR interface [chars].

VP enable failed on ACR physical interface.

ACR_DDTS_COMPONENT

"Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3-ISSU_SENDFAILED

3-Error

\nACR ISSU: send message failed rc = [dec]\n

The sending of a message has failed.

ACR_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

ACR-4-ISSU_INCOMPATIBLE

4-Warning

\nacr-issu-compat: returned FALSE

The compatibility checking has failed

ACR_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

ACR-4-ISSU_XFORM

4-Warning

\n[chars]: failed rc=[chars]

The transform has failed.

ACR_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

ACR-6- ACRPVCADD

6-Information

PVC creation failed for VCD= [dec] on [chars] interface of ACR interface [chars].

PVC creation attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-6- ACRPVCDEL

6-Information

PVC deletion failed for VCD= [dec] on [chars] interface of ACR group [chars].

PVC deletion attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."