Download/Backup Configuration on the WAP371

Available Languages

Download Options

  • PDF     (460.7 KB)
    View with Adobe Reader on a variety of devices
  • ePub     (481.7 KB)
    View in various apps on iPhone, iPad, Android, Sony Reader, or Windows Phone
  • Mobi (Kindle)     (816.5 KB)
    View on Kindle device or Kindle app on multiple devices
Updated:August 2, 2017
Document ID:SMB5062

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Download/Backup Configuration on the WAP371

Objective

Backup configuration files help a network administrator restore the access point back to an older configuration. Network administrators can use saved backup files to restore devices to a known working configuration.

The objective of this article is to show you how to download and backup the configuration of the WAP371.

Applicable Devices

• WAP371

Software Version

• 1.1.2.3

Download/Backup Configuration File

Backup Configuration File via TFTP

Follow the steps given below to download the configuration file via TFTP. Trivial File Transfer Protocol or TFTP is a simplified unsecure version of File Transfer Protocol (FTP). It is mainly used to upgrade/backup firmware and to distribute software among corporate networks. TFTP has a server and client setup. The WAP acts as a TFTP client.

Note: You need to have a TFTP server installed in your PC for this task. Industry standard TFTP servers, TFTPd32 or TFTPd64, can be downloaded here.

Step 1. Log in to the web configuration utility and choose Administration > Download/Backup Configuration File. The Download/Backup Configuration File page opens:

Step 2. Click the via TFTP radio button to transfer the configuration file via TFTP.

Step 3. Click the Backup (AP to PC) radio button to back up the configuration file from the Access Point to the TFTP Server.

Step 4. Click the appropriate Source File Type radio button that needs to be backed-up.

The available file types are defined as follows:

• Startup Configuration — The configuration used by the access point to boot up. The Startup Configuration file is stored in flash memory.

• Mirror Configuration — If the Startup Configuration is not modified for at least 24 hours, it is automatically saved to a Mirror Configuration. The Mirror Configuration can be used to recover a system configuration after a factory reset by copying the Mirror Configuration to the Startup Configuration. Mirror configuration can only be selected when you select Backup (AP to PC) in the Save Action field.

Note: Backup Configuration can only be downloaded from the TFTP Server to the access point.

Step 5. Enter the destination file name in the Destination File Name field.

Note: The destination file name needs to have an .xml extension. The file can be named as desired, and the name selected will have no impact on the operation of the access point.

Step 6. Enter the IP address of the TFTP server in the TFTP Server IPv4 Address field.

Step 7. Click Save to save the configuration file to the TFTP Server.

The File transfer progress bar appears. Depending on your web browser, the configuration file will be downloaded to the default download destination.

Download Configuration File via TFTP

Follow the steps given below to download the configuration file to your wireless access point (WAP) via TFTP. Trivial File Transfer Protocol (TFTP) is a simplified unsecure version of File Transfer Protocol (FTP). It is mainly used to upgrade/backup firmware and to distribute software among corporate networks. TFTP has a server and client setup. The WAP acts as a TFTP client.

Note: You need to have a TFTP server installed in your PC for this task. An industry standard TFTP server, TFTPd32 and TFTPd64, can be downloaded here.

Step 1. Log in to the web configuration utility and choose Administration > Download/Backup Configuration File. The Download/Backup Configuration File page opens:

Step 2. In the Transfer Method field, click the via TFTP radio button to transfer the configuration file via TFTP.

Step 3. In the Save Action field, click the Download (PC to AP) radio button to download the configuration file from the TFTP Server to the Access Point.

Step 4. Enter the name of the file to be downloaded from the PC to the Access Point in the Source File Name field. The file should have a .xml extension, and should match the name of the file downloaded previously.

Step 5. Enter the IP address of the TFTP server in the TFTP Server IPv4 Address field.

Step 6. In the Destination File Type field, click either the Startup Configuration or Backup Configuration radio button for the destination file type.

The available file types are defined as follows:

• Startup Configuration — The configuration used by the access point to boot up. The Startup Configuration file is stored in flash memory.

• Backup Configuration — A backup copy of the configuration file that can be used to restore the configuration in the case of an access point crash. The Backup Configuration file is saved on the NVRAM or permanent memory.

Step 7. Click Save.

Caution: Once the configuration is restored, the device reboots and resumes normal operation. Until then, please do not refresh the access point. Any clients on the access point might lose connection to the AP while it reboots.

Backup Configuration File via HTTP/HTTPS

Follow the steps to back up the configuration file via HTTP/HTTPS. You can download or backup files through your web browser with the use of HTTP/HTTPS protocol. Hypertext Transfer Protocol (HTTP) provides a simple challenge-response authentication framework that can be used by a client to provide authentication framework.

Step 1. Log in to the web configuration utility and choose Administration > Download/Backup Configuration File. The Download/Backup Configuration File page opens:

Step 2. Click the via HTTP/HTTPS radio button to transfer the configuration file via HTTP/HTTPS.

Step 3. Click the Backup (AP to PC) radio button to back up the configuration file from the Access Point to the PC.

Step 4. In the Source File Type field, click either the Startup Configuration or Mirror Configuration radio button for the source file type. Backup Configuration is only available when the Download (PC to AP) radio button is selected in the Save Action field.

The available file types are defined as follows:

• Startup Configuration — The configuration used by the access point to boot up. The Startup Configuration file is stored in flash memory.

• Mirror Configuration — If the Startup Configuration is not modified for at least 24 hours, it is automatically saved to a Mirror Configuration. The Mirror Configuration can be used to recover a system configuration after a factory reset by copying the Mirror Configuration to the Startup Configuration.

Note: Backup Configuration can only be downloaded from the PC to the access point.

Step 5. Click Save to save the configuration file to your PC. Depending on your web browser, the configuration file will be downloaded to the default download destination.

Download Configuration File via HTTP/HTTPS

Follow the steps to download the configuration file via HTTP/HTTPS. You can download or backup files through your web browser with the use of the HTTP/HTTPS protocol. Hypertext Transfer Protocol (HTTP) provides a simple challenge-response authentication framework that can be used by a client to provide authentication framework.

Step 1. Log in to the Web configuration utility and choose Administration > Download/Backup Configuration File. The Download/Backup Configuration File page opens:

Step 2. Click via HTTP/HTTPS to transfer the configuration file via HTTP/HTTPS.

Step 3. Click the Download (PC to AP) radio button to download the configuration file from the PC to the Access Point.

Step 4. Click Browse to locate and choose the source file from the PC. The file name of the chosen file appears beside the button.

Step 5. Select either the Startup Configuration or the Backup Configuration radio button to choose which configuration to overwrite.

The available file types are defined as follows:

• Startup Configuration — The configuration used by the access point to boot up. The Startup Configuration file is stored in flash memory.

• Backup Configuration — A backup copy of the configuration file that can be used to restore the configuration in the case of an access point crash. The Backup Configuration file is saved on the NVRAM or permanent memory.

Step 6. Click Save.

Caution: Once the configuration is restored, the device reboots and resumes normal operation. Until then, please do not refresh the access point. Any clients on the access point might lose connection to the AP while it reboots.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco