Coherent Optics Commands

ampli-control-mode

To configure the mode of operation of the OLS pluggable to either gain control or power control mode, use the ampli-control-mode command in the controller ots configuration mode.

ampli-control-mode { powermode | manual }

Syntax Description

powermode

Configures the OLS pluggable to power control mode.

manual

Configures the OLS pluggable to gain control mode.

Command Default

None.

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None.

Task ID

Task ID Operation
dwdm

read, write

Examples

The following example shows how to configure the gain control operational mode and the amplifier gain of the OLS pluggable :

Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#ampli-control-mode manual
Router(config-Ots)#egress-ampli-gain +30
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

controller coherentDSP

To configure the coherent DSP controller, use the controller coherentDSP command in the Coherent DSP controller configuration mode.

controller coherentDSP R/S/I/P [ description description | perf-mon { enable | disable } | pm { 30-sec |15-min |24-hour } { fec } { report | threshold } value | secondary-admin-state { maintenance | normal } loopback { internal | line }]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the coherent DSP controller.

description description

Description of the coherent DSP controller.

perf-mon{ enable| disable}

Enables or disables performance monitoring.

pm { 30-sec |15-min |24-hour} { fec} { report | threshold} value

Configures performance monitoring parameters for 30-second,15-minute, or 24-hour intervals.

The fec keyword configures FEC PM data in 30-second, 15-minute, or 24-hour intervals.

The report keyword configures threshold crossing alerts (TCA) reporting status for the PM parameters.

The threshold keyword configures threshold values for the PM parameters.

The PM parameters that can be configured are:

  • Inst-Q-margin (Instantaneous Q margin)

  • Q threshold

  • Q-margin

  • ec-bits (error corrected bits)

  • post-FEC BER

  • pre-FEC BER

  • uc-words (uncorrected words)

secondary-admin-state

Configures the administrative state of the controller. The states are maintenance or normal.

loopback{ internal| line}

Configures the internal or line loopback mode on the controller.

Command Default

None.

Command Modes

Coherent DSP controller configuration

Command History

Release Modification
Release 7.3.2

This command was introduced.

Examples

The following example shows how to enable line loopback configuration on coherent DSP controllers:

Router#config
Router(config)#controller coherentDSP 0/0/0/4
Router(config-CoDSP)#secondary-admin-state maintenance
Router(config-CoDSP)#loopback line
Router(config-CoDSP)#commit

controller optics

To configure the optics controller, use the controller optics command in the optics controller configuration mode.

controller optics R/S/I/P [ DAC-Rate rate | cd-max cd-max | cd-min cd-min | cd-low-threshold cd-low | cd-high-threshold cd-high | dgd-high-threshold dgd-value | dwdm-carrier channel-grid | lbc-high-threshold lbc-value | osnr-low-threshold osnr-value description description | fec fec-mode | sec-admin-state {maintenance | normal} | shutdown | transmit-power transmit-power | perf-mon { enable | disable } | host { auto-squelch } { disable } | pm { 30-sec |15-min | 24-hour } { optics } { report | threshold } pm-parameter value ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the optics controller.

DAC-Rate rate

Sets the DAC (digital to analog conversion) sampling rate for this controller. The sampling rate options available are:

  • 1x1

  • 1x1.25

cd-max cd-max (Only for trunk optics controllers) Maximum chromatic dispersion. For QDD-400G-ZR-S optical module, the range is 0 to +2400. For QDD-400G-ZRP-S optical module, the range is 0 to +80000 ps/nm.
cd-min cd-min (Only for trunk optics controllers) Minimum chromatic dispersion. For QDD-400G-ZR-S optical module, the range is -2400 to 0. For QDD-400G-ZRP-S optical module, the range is -80000 to 0 ps/nm.
cd-low-threshold cd-low (Only for trunk optics controllers) Minimum acceptable chromatic dispersion value. The CD alarm is raised if the chromatic dispersion goes below this value. This is an alarm threshold parameter. For QDD-400G-ZR-S optical module, the range is -2400 to 0. For QDD-400G-ZRP-S optical module, the range is -80000 to 0 ps/nm.
cd-high-threshold cd-high

(Only for trunk optics controllers) Maximum acceptable chromatic dispersion value. The CD alarm is raised if the chromatic dispersion exceeds this value. This is an alarm threshold parameter. For QDD-400G-ZR-S optical module, the range is 0 to +2400. For QDD-400G-ZRP-S optical module, the range is 0 to +80000 ps/nm.

dgd-high-threshold dgd-value

(Only for trunk optics controllers) Configures the maximum acceptable Differential Group Delay (DGD) value. The DGD alarm is raised if DGD exceeds this value. This is an alarm threshold parameter.

The range is 0 to 18000 (in the units of 0.01 ps).

dwdm-carrier channel-grid

Configures the DWDM carrier channel. Options are:

  • 100MHz-grid

  • 50GHz-grid

lbc-high-threshold lbc-value

Configures the high laser bias current threshold. This is an alarm threshold parameter.

The range is 0 to 100%

osnr-low-threshold osnr-value

(Only for trunk optics controllers) Configures the minimum acceptable Optical Signal-to-Noise ratio (OSNR) value. The OSNR alarm is raised if OSNR goes below this value. This is an alarm threshold parameter.

The range is 0 to 4000 (in units of 0.01db).

description description

Description of the optics controller.

fec fec-mode

Configures Forward Error Correction (FEC) modes.

sec-admin-state

Configures the administrative state of the controller. The values are maintenance or normal.

shutdown

Disables the configuration of the controller.

pm{ 30-sec |15-min |24-hour} { optics} { report | threshold} pm-parameter value

Configures performance monitoring parameters for 30-second, 15-minute, and 24-hour intervals.

The report keyword configures threshold crossing alerts (TCA) reporting status for the PM parameters.

The threshold keyword configures threshold values for the PM parameters.

The PM parameters that can be configured are:

  • cd (chromatic dispersion)

  • dgd (differential group delay)

  • low-freq-off (low signal frequency offset)

  • opr (optical power RX)

  • osnr (optical signal-to-noise ratio)

  • pcr (polarization change rate)

  • pdl (polarization dependent loss)

  • rx-sig (receiving signal power)

  • snr (signal-to-noise ratio)

  • sopmd (second order polarization mode dispersion)

transmit-power transmit-power

(Only for trunk optics controllers) Configures the transmit power. The range is -190 to 50 dBm (in the units of 0.1 dBm).

host{ auto-squelch} { disable}

Disable squelch for host.

perf-mon { enable | disable }

Enables or disables performance monitoring.

Command Default

Table 1. Supported Line Cards and Modes

Line Card

Default Port Speed

Supported Front Panel Ports

1x400G Transponder Mode

4x100G Muxponder Mode

3x100G Muxponder Mode

2x100G Muxponder Mode

1x100G Transponder Mode

A9K-20HG-FLEX-SE / A9K-20HG-FLEX-TR

1x100G

0, 7, 8, 12, 19

Yes

Yes

No

No

Yes

A9K-8HG-FLEX-SE / A9K-8HG-FLEX-TR

1x100G

0, 7

Yes

Yes

No

No

Yes

A99-10X400GE-X-SE / A99-10X400GE-X-TR

1x400G

3, 5, 6, 7, 9

Yes

Yes

No

Yes

Yes

A9903-20HG-PEC

1x100G

0, 4, 8, 12, 16

Yes

No

No

No

Yes

Command History

Release Modification

Release 7.3.2

This command was introduced.

Release 7.10.1

The following keyword was introduced:

  • host auto-squelch disable

Command Modes

Optics controller configuration

Usage Guidelines

The configurations for chromatic dispersion, cd-low-threshold, and cd-high-threshold must be performed only after the hw-module configuration. These configurations must be removed before the no hw-module configuration. Default values are set to optimize the power consumption by the QDD-400G-ZR-S and QDD-400G-ZRP-S modules.

Examples

The following example shows how to configure the optics controller and set the ranges for chromatic dispersion:

Router#configure
Router(config)#controller optics 0/0/1/1
Router(config-optics)#cd-max 2000
Router(config-optics)#cd-min -2000
Router(config)#commit

The following is a sample in which the performance monitoring parameters of optics controller are configured in 24-hour intervals:

Router#configure
Router(config)#controller optics 0/0/1/1
Router(config-optics)#perf-mon enable
Router(config-optics)#pm 24-hour optics threshold osnr max 345
Router(config)#commit

This example shows how to disable laser squelching for host on controller optics:


router#config
router(config)#controller 0/0/0/0
router(config-Optics)#host auto-squelch disable
router(config-Optics)#commit

controller ots (QDD OLS)

To configure the QDD OLS pluggable (ots controller), use the controller ots command in the global configuration mode.

controller ots R/S/I/P/SuP

Syntax Description

R/S/I/P/SuP

Rack/Slot/Instance/Port/Sub-Port of the QDD OLS pluggable.

SuP is the QDD pluggable subport which can be 0 or 1. Com port is represented as 0 and line port is represented as 1.

Command Default

None.

Command Modes

Global Configuration

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None.

Task ID

Task ID Operation

dwdm

read, write

sonet-sdh

read, write

interface

read, write

Examples

This example shows how to configure the ots controller and set the low- power threshold at the transmit and receive side.

Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#rx-low-threshold -200
Router(config-Ots)#tx-low-threshold -200
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

egress-ampli-gain

To configure the amplifer gain of the OLS pluggable, use the egress-ampli-gain command in the controller ots configuration mode.

egress-ampli-gain gain-value

Syntax Description

gain-value

Sets the amplifier gain value. The range is <+30, +400> in units of 0.1dB.

  • For subport 0, the range is from +30 db to + 250 db

  • For subport 1, the range is from +70 db to +250 db

Command Default

None.

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None.

Task ID

Task ID Operation
dwdm

read, write

Examples

The following example shows how to configure the gain control operational mode and the amplifier gain of the OLS pluggable :

Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#ampli-control-mode manual
Router(config-Ots)#egress-ampli-gain +30
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

egress-ampli-osri

To shutdown the amplifier (QDD OLS pluggable), use the egress-ampli-osri command in the controller ots configuration mode.

egress-ampli-osri { off | on }

Syntax Description

off

Disables the Optical Safety Remote Interlock (OSRI) configuration.

on

Enables the Optical Safety Remote Interlock (OSRI) configuration.

Command Default

None

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

The OSRI configuration is used during the maintenance of the pluggable, debugging scenarios, and when the OLS pluggable is not in use.

Task ID

Task ID Operation
dwdm

read, write

Examples

The following example shows how to configure the Optical Safety Remote Interlock (OSRI) on the OLS pluggable:
Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#egress-ampli-osri on
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

egress-ampli-power

To configure the amplifier output power of the OLS pluggable, use the egress-ampli-power command in the controller ots configuration mode.

egress-ampli-power power-value

Syntax Description

power-value

Sets the amplifier power value. The range is <-30, +250> in units of 0.1dB.

  • For subport 0, the range is from 10 dB to 170 dB

  • For subport 1, the range is from 0 dB to 170 dB

Command Default

None.

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None.

Task ID

Task ID Operation
dwdm

read, write

Examples

The following example shows how to configure the power control operational mode and the amplifier output power of the OLS pluggable :
Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#ampli-control-mode powermode
Router(config-Ots)#egress-ampli-power 30
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

egress-ampli-safety-control-mode

To enable the safety control mode in the OLS pluggable, use the egress-ampli-safety-control-mode command in the controller ots configuration mode.

egress-ampli-safety-control-mode { auto | disabled }

Syntax Description

auto

Enables the safety control mode (automatic laser shutdown (ALS)) only on sub-port 1 of the OLS pluggable.

disabled

Disables the safety control mode (automatic laser shutdown (ALS)) on sub-port 1 of the OLS pluggable.

Command Default

None

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

You can enable safety control mode only on subport 1. With safety-control-mode set as auto and if LOS is detected on the line RX, the line TX normalizes the signal output power to 8 dBm and the ALS alarm is raised.

Task ID

Task ID Operation
dwdm

read, write

Examples

The following example shows how to enable the safety control mode on the OLS pluggable (on sub-port 1):
Router#config
Router(config)#controller ots 0/0/2/1/1
Router(config-Ots)#egress-ampli-safety-control-mode auto
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

hw-module location

To configure breakout, use the hw-module location command in the global configuration mode.

hw-module location node-id [bay bay-number ] port port-number breakout muxponder-mode

Syntax Description

location node-id

Specify the node location.

bay bay-number

Applicable only for Cisco ASR 9903 router.

The bay-number is always 1.

port port-number

Specify the port number.

breakout breakout-mode options

Configures the breakout for this controller. The router displays these breakout mode options:

  • 1x400GbE

  • 1x100GbE

  • 2x100GbE

  • 4x100GbE

  • 2x40GbE

  • 1x40GbE

  • 4x25GbE

  • 4x10GbE

  • 1x10GbE

Command Default

None.

Command Modes

Global Configuration

Command History

Release Modification

Release 7.3.2

This command was enhanced to support QDD-400G-ZR-S and QDD-400G-ZRP-S optical modules.

Release 24.3.1

This command was enhanced to support the 1x10GbE breakout mode on the Cisco ASR 9903 router and Cisco A9K-20HG-FLEX-SE line cards with SFP-10G-ER, SFP-10G-ZR, and SFP-10G-LR hot-pluggable transceiver modules.

Usage Guidelines

For additional information, see the "Configuring Breakout" section in the "Configuring 400G Digital Coherent Optics" chapter of Interface and Hardware Component Configuration Guide for Cisco ASR 9000 Series Routers.

Examples

This example shows how to configure the 4x100 muxponder mode using the hw-module location command:

Router#configure
Router(config)#hw-module port 1 location 0/1/0/3 breakout 4xHundredGigE
Router(config)#commit

Examples

This example shows how to configure the 1x10GbE breakout mode using the hw-module location command:

Router#configure
Router(config)#hw-module location 0/0/CPU0 bay 1 port 9 breakout 1xTenGbE
Router(config)#commit

rx-low-threshold

To configure the low receive (RX) power threshold on the QDD OLS pluggable, use the rx-low-threshold command in the controller ots configuration mode.

rx-low-threshold rx-low

Syntax Description

rx-low

Configures the low receive power threshold. The range is -400 to 400 (in the units of 0.1 dBm).

  • For subport 0, the range is from -300 dBm to 170 dBm

  • For subport 1, the range is from -300 dBm to 170 dBm

Command Default

None.

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None.

Task ID

Task ID Operation
dwdm

read, write

Examples

This example shows how to configure the ots controller and set the low power threshold at the receiving side.

Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#rx-low-threshold -200
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit

show controllers coherentDSP

To display the status and configuration information about the interfaces configured as coherent DSP controllers on a specific node, use the show controllers coherentDSP command in XR EXEC mode.

show controller coherentDSP R/S/I/P [ pm { current | history } { 30-sec | 15-min | 24-hour } { fec } ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the coherent DSP controller.

pm

Displays performance monitoring parameters for the controller.

current

Displays the current performance monitoring data in 30-second, 15- minute, and 24-hour intervals.

history

Displays the historical performance monitoring data in 30-second, 15-minute, and 24-hour intervals.

fec

The fec keyword displays FEC PM data in 30-second, 15-minute, or 24-hour intervals.

Command Default

No default behavior or values

Command Modes

XR EXEC mode

Command History

Release Modification
Release 7.3.2

This command was introduced.

Examples

The following is a sample to view the status and configuration information about the coherent DSP controller.

Router#show controllers coherentDSP 0/19/0/3

Port                                            : CoherentDSP 0/19/0/3
Controller State                                : Up
Inherited Secondary State                       : Normal
Configured Secondary State                      : Normal
Derived State                                   : In Service
Loopback mode                                   : None
BER Thresholds                                  : SF = 1.0E-5  SD = 1.0E-7
Performance Monitoring                          : Enable
Bandwidth                                       : 100.0Gb/s

Alarm Information:
LOS = 0 LOF = 0 LOM = 0
OOF = 0 OOM = 0 AIS = 0
IAE = 0 BIAE = 0        SF_BER = 0
SD_BER = 0      BDI = 0 TIM = 0
FECMISMATCH = 0 FEC-UNC = 0     FLEXO_GIDM = 0
FLEXO-MM = 0    FLEXO-LOM = 0   FLEXO-RDI = 0
FLEXO-LOF = 1
Detected Alarms                                 : None

Bit Error Rate Information
PREFEC  BER                                     : 0.0E+00 
POSTFEC BER                                     : 0.0E+00 
Q-Factor                                        : 16.50 dB 

Q-Margin                                        : 9.90dB 

OTU TTI Received 

FEC mode                                        : O_FEC 

The following is a sample to view the current performance monitoring parameters of the coherent DSP controller in 30 second intervals.

Router#show controllers coherentDSP 0/0/0/13 pm current 30-sec fec
g709 FEC in the current interval [07:03:00 - 07:03:29 Thu May 27 2021]

FEC current bucket type : Valid
    EC-BITS   : 11885430510             Threshold : 83203400000            TCA(enable)  : YES
    UC-WORDS  : 0                       Threshold : 5                      TCA(enable)  : YES

                                      MIN       AVG        MAX      Threshold   TCA     Threshold     TCA
                                                                       (min)    (enable)    (max)     (enable)
PreFEC BER                     :     8.4E-04   8.6E-04   8.7E-04     0E-15       NO       0E-15        NO
PostFEC BER                    :     0E-15     0E-15     0E-15       0E-15       NO       0E-15        NO
Q[dB]                          :     9.90      9.90      9.90        0.00        NO        0.00        NO
Q_Margin[dB]                   :     2.70      2.70      2.70        0.00        NO        0.00        NO

Last clearing of "show controllers OTU" counters never

show controllers optics

To display status and configuration information about the interfaces configured as optics controller on a specific node, use the show controllers optics command in XR EXEC mode.

show controller optics R/S/I/P [ pm { current | history } { 30-sec | 15-min | 24-hour } { optics } { lane-number } ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the optics controller.

pm

Displays performance monitoring parameters for the controller.

current

Displays the current performance monitoring data in 30 second, 15 minute, and 24 hour intervals.

history

Displays the historical performance monitoring data in 30 second, 15 minute, and 24 hour intervals.

optics

Displays the PM data for optics controller.

lane-number

Displays the performance monitoring data for the applicable lanes in the optical module. The lane number is always 1.

Command Default

No default behavior or values

Command Modes

XR EXEC mode

Command History

Release Modification

Release 6.4.1

This command was introduced.

Release 7.3.2

This command was updated to reflect the QDD-400G-ZR-S and QDD-400G-ZRP-S changes in the output.

Usage Guidelines

To display the firmware version of the optical module, use the show controllers optics R/S/I/P | inc Firmware command.
Router#show controllers optics 0/0/0/3  | inc Firmware
         Firmware Version       : 61.20 (Build : 13)

Examples

The following example displays the output of the show controllers optics command:

Router#show controllers optics 0/0/0/3
Controller State: Up
Transport Admin State: In Service 
Laser State: On
LED State: Green
FEC State: FEC CFEC
 Optics Status
         Optics Type:  400G QSFP-DD ZR
         DWDM carrier Info: C BAND, MSA ITU Channel=61, Frequency=193.10THz,
         Wavelength=1552.524nm
         Alarm Status:
         -------------
         Detected Alarms: None 
         LOS/LOL/Fault Status:
         Laser Bias Current = 52.5 mA
         Actual TX Power = -8.51 dBm
         RX Power = -8.67 dBm
         RX Signal Power = -8.66 dBm
         Frequency Offset = 0 MHz
         Laser Temperature = 62.21 Celsius
         Laser Age = 0 %
         DAC Rate = 1x1

         Performance Monitoring: Enable
 
         THRESHOLD VALUES
         ----------------
 
         Parameter                 High Alarm  Low Alarm  High Warning  Low Warning
         ------------------------  ----------  ---------  ------------  -----------
         Rx Power Threshold(dBm)          1.9      -28.2           0.0        -25.0
         Tx Power Threshold(dBm)          0.0      -18.0          -2.0        -16.0
         LBC Threshold(mA)               0.00       0.00          0.00         0.00
         Temp. Threshold(celsius)       80.00      -5.00         75.00        15.00
         Voltage Threshold(volt)         3.46       3.13          3.43         3.16
 
         LBC High Threshold = 98 %
         Configured Tx Power = -7.00 dBm
         Configured CD High Threshold = 80000 ps/nm
         Configured CD lower Threshold = -80000 ps/nm
         Configured OSNR lower Threshold = 9.00 dB
         Configured DGD Higher Threshold = 180.00 ps
         Baud Rate =  59.8437500000 GBd
         Modulation Type: 16QAM
         Chromatic Dispersion 0 ps/nm
         Configured CD-MIN -2400 ps/nm  CD-MAX 2400 ps/nm
         Second Order Polarization Mode Dispersion = 25.00 ps^2
         Optical Signal to Noise Ratio = 36.40 dB
         Polarization Dependent Loss = 0.07 dB
         Polarization Change Rate = 0.00 rad/s
         Differential Group Delay = 1.00 ps
 
         Temperature = 59.00 Celsius
         Voltage = 3.31 V
 
Transceiver Vendor Details
 
         Form Factor            : QSFP-DD
         Optics type            : QSFP-DD 400G-ZR-S
         Name                   : CISCO-ACACIA
         OUI Number             : 7c.b2.5c
         Part Number            : DP04QSDD-E20-19E
         Rev Number             : 01
         Serial Number          : ACA2504002U
         PID                    : QDD-400G-ZR-S
         VID                    : ES03
         Firmware Version       : 161.20 (Build : 9)
         Date Code(yy/mm/dd)    : 21/02/03
 

The following is a sample to view the current performance monitoring parameters of the optics controller in 30 second intervals.

Router#show controllers optics 0/0/0/7 pm current 30-sec optics 1
Optics in the current interval [07:11:30 - 07:11:33 Thu May 27 2021]
Optics current bucket type : Valid
             MIN       AVG       MAX      Operational      Configured      TCA   Operational      Configured     TCA
                                          Threshold(min)   Threshold(min) (min) Threshold(max)   Threshold(max) (max)
LBC[% ]      : 0.0       0.0       0.0      0.0               NA              NO   100.0            NA              NO   
OPT[dBm]     : -7.92     -7.92     -7.92    -15.09            NA              NO   0.00             NA              NO   
OPR[dBm]     : -8.20     -8.19     -8.18    -30.00            NA              NO   8.00             NA              NO   
CD[ps/nm]    : -1        -1        0        -80000            NA              NO   80000            NA              NO   
DGD[ps ]     : 4.00      4.00      4.00     0.00              NA              NO   80.00            NA              NO   
SOPMD[ps^2]  : 46.00     48.00     50.00    0.00              NA              NO   2000.00          NA              NO   
OSNR[dB]     : 36.40     36.40     36.40    9.00              NA              NO   40.00            NA              NO   
PDL[dB]      : 0.08      0.09      0.09     0.00              NA              NO   7.00             NA              NO   
PCR[rad/s]   : 0.00      0.00      0.00     0.00              NA              NO   2500000.00       NA              NO   
RX_SIG[dBm]  : -7.40     -7.40     -7.39    -30.00            NA              NO   1.00             NA              NO   
FREQ_OFF[Mhz]: -99       -93       -87      -3600             NA              NO   3600             NA              NO   
SNR[dB]      : 18.40     18.45     18.50    7.00              NA              NO   100.00           NA              NO   

Last clearing of "show controllers OPTICS" counters never

show controllers ots (QDD OLS)

To display the configuration details of the OLS pluggable, use the show controllers ots command in XR EXEC mode.

show controllers ots R/S/I/P/SuP

Syntax Description

R/S/I/P/SuP

Rack/Slot/Instance/Port/Sub-Port of the QDD OLS pluggable.

SuP is the QDD pluggable sub-port which can be 0 or 1. Com port is represented as 0 and line port is represented as 1.

Command Default

None.

Command Modes

XR EXEC

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None

Task ID

Task ID Operation
interface

read

Examples

The following example displays the configuration details of the OLS pluggable:

Router#show controllers ots 0/0/1/1/1
Wed Mar 29 06:59:00.016 UTC

 Controller State: Up 

 Transport Admin State: In Service 

 LED State: Yellow 

         Alarm Status:
         -------------
         Detected Alarms: None


         Alarm Statistics:
         -----------------
         RX-LOS-P = 1          
         RX-LOC = 0          
         TX-POWER-FAIL-LOW = 0          
         INGRESS-AUTO-LASER-SHUT = 0          
         INGRESS-AUTO-POW-RED = 0          
         INGRESS-AMPLI-GAIN-LOW = 0          
         INGRESS-AMPLI-GAIN-HIGH = 0          
         EGRESS-AUTO-LASER-SHUT = 1          
         EGRESS-AUTO-POW-RED = 1          
         EGRESS-AMPLI-GAIN-LOW = 0          
         EGRESS-AMPLI-GAIN-HIGH = 0          
         HIGH-TX-BR-PWR = 0          
         HIGH-RX-BR-PWR = 0          
         SPAN-TOO-SHORT-TX = 0          
         SPAN-TOO-SHORT-RX = 0          

         Parameter Statistics:
         ---------------------
         Total Tx Power = 7.52 dBm 
         Rx Signal Power = -26.77 dBm 
         Tx Signal Power = 7.23 dBm 
         Egress Ampli Gain = 20.8 dB
         Egress Ampli Safety Control mode = auto 
         Egress Ampli OSRI = OFF 
          
          
         Configured Parameters:
         -------------
         Egress Ampli Gain = 15.0 dB 
         Egress Ampli Power = 8.0 dBm
         Egress Ampli Safety Control mode = auto 
         Egress Ampli OSRI = OFF 
         Ampli Control mode = Manual 
         Rx Low Threshold = -30.0 dBm 
         Tx Low Threshold = -5.0 dBm 
          
          
         Temperature = 35.09 Celsius 
         Voltage = 3.37 V 
          
 Optical Module Details
          
         Optics type            : QDD DUAL EDFA
         Name                   : CISCO-ACCELINK
         OUI Number             : 00.00.00
         Part Number            : EDFA-211917-QDD
         Rev Number             : 21
         Serial Number          : ACW2651Z003
         PID                    : ONS-QDD-OLS
         VID                    : VES1
         Firmware Version       : 2.01
         Date Code(yy/mm/dd)    : 22/12/28
         Fiber Connector Type   : CS 
 

tx-low-threshold

To configure the low transmit (TX) power threshold on the QDD OLS pluggable, use the tx-low-threshold command in the controller ots configuration mode.

tx-low-threshold tx-low

Syntax Description

tx-low

Configures the low transmit power threshold. The range is -400 to 400 (in the units of 0.1 dBm).

  • For subport 0, the range is from -50 dBm to 190 dBm

  • For subport 1, the range is from -50 dBm to 190 dBm

Command Default

None.

Command Modes

controller ots

Command History

Release Modification
Release 25.3.1

This command was introduced.

Usage Guidelines

None.

Task ID

Task ID Operation
dwdm

read, write

Examples

This example shows how to configure the ots controller and set the low power threshold at the transmit side.

Router#config
Router(config)#controller ots 0/0/2/1/0
Router(config-Ots)#tx-low-threshold -200
Router(config-Ots)#commit
Router(config-Ots)#exit
Router(config)#exit