Release Notes for Cisco Mobility Services Engine, Release 7.6.100.0
Available Languages
Table of Contents
Release Notes for Cisco Mobility Services Engine, Release 7.6.100.0
Cisco Mobility Services Engine and Services
Cisco MSE and Cisco Converged Access Solution Compatibility Matrix
Upgrading the MSE to 7.6 from 7.x Release Without Data Migration
Upgrading the MSE to 7.6 from 7.x Release
Restoring an Old Database to 7.6
Updated Software Version Shown in the Prime Infrastructure After Polling
Base Location, CMX, and wIPS License Requirements
Cisco Mobility Services Licenses for High Availability
Operational Notes for a Mobility Services Engine
How and When to Use the db.tar installer
Reboot MSE After Fresh Installation or Upgrade
Automatic Installation Script for Initial Setup
Parameter Changes During Upgrade from 6.0.x to 7.0.x
Mandatory Default Root Password Change
Configuring the Prime Infrastructure Communication Username and Password Using MSE setup.sh
Configuration Changes for Greater Location Accuracy
AeroScout Engine Module Changes
Operational Notes for Connected Mobile Experiences
Synchronization Required When Upgrading to Release 7.6 or Importing CAD Floor Images
Floor Change or Minimum Distance Required for Location Transitions to Post to the History Log
Non-Cisco Compatible Extensions Tags Not Supported
Cisco Compatible Extensions Version 1 Tags Required at a Minimum
Monitoring Information Varies for Clients and Tags
Location History Time stamps Match Browser Location
PDAs and Smartphone with Limited Probe Requests Might Affect Location
Prime Infrastructure Screen and Navigation Changes
Operational Notes for CMX Analytics
Obtaining Documentation and Submitting a Service Request
Release Notes for Cisco Mobility Services Engine, Release 7.6.100.0
These release notes describe the requirements, features, limitations, restrictions (caveats), and related information for release 7.6 of the Cisco mobility services engine and its services.
- Connected Mobile Experiences
- Wireless Intrusion Protection System (wIPS)
- Mobile Concierge Service
- CMX Analytics Service
- CMX Browser Engage
- CMX HTTP Proxy Service
Note Before installing this software, see the “Upgrading the MSE” section for details on compatibility with the Cisco wireless LAN controllers (WLC) and the Cisco Prime Infrastructure.
Note You need licenses to run all the services. For ordering information, see the “Licensing Information for MSE” section.
Note Cisco 3310 and Cisco 3350 mobility services engines are not supported from Release 7.4 onwards.
Introduction
This section introduces the Cisco mobility services engine (MSE) and the various services that it supports.
Cisco Mobility Services Engine and Services
The Cisco mobility services engine supports various services within the overall Cisco Unified Wireless Network (CUWN).
The Cisco mobility services engine currently supports the following services in Release 7.6:
- Connected Mobile Experiences—Allows a mobility services engine to simultaneously track thousands of mobile assets and clients by retrieving contextual information such as presence, location, telemetry data, and historical information.
- Wireless Intrusion Protection Service—Provides wireless-specific network threat detection and mitigation against malicious attacks, security vulnerabilities, and sources of performance disruption within the CUWN infrastructure. wIPS visualizes, analyzes, and identifies wireless threats, and centrally manages mitigation and resolution of security and performance issues using Cisco monitor mode and Enhanced Local Mode (ELM) Access Points. Proactive threat prevention is also supported to create a hardened wireless network core that is impenetrable by most wireless attacks.
- Mobile Concierge—Mobile Concierge enables the Cisco Mobility Services Advertisement Protocol (MSAP). This protocol enables direct communication between the MSE and mobile devices, allowing content to be pushed directly to the mobile device pre-association. This functionality is dependent on the mobile device supporting 802.11u and MSAP.
- CMX Analytics Service—The CMX Analytics service analyzes wireless device location information in a particular network. The CMX Analytics service uses the data provided by the Cisco Mobility Services Engine (MSE) to calculate the location of Wi-Fi devices in the Wireless Local Area Network (WLAN). When a wireless device is enabled in a network, it transmits probe request packets to identify the wireless network in its neighborhood. Even after connecting to the access point in the WLAN, the client devices continue to transmit probe request packets to identify other access points for better quality of service. The access points gather these request and the associated RSSI from the various wireless devices and forwards them to the Wireless LAN Controller (WLC). The controller then forwards this information to the MSE.
The basic data that is collected from various APs, when analyzed, produces information and knowledge about the movement and behavior patterns of people who are using Wi-Fi devices in the building. For example, the building can be an airport, shopping mall, city center, and so on. The CMX Analytics service helps the airport authorities or the building owners to understand the movement of passengers or customer within their building. This helps them improve the signage, make changes to the under utilized areas, and so on.
- CMX Browser Engage Service—The CMX Browser Engage is a new way to transform the in-venue experience through browser engagement. This enables organizations to communicate with opt-in mobile users - shoppers, guests, and visitors - through their mobile browser. The CMX Dashboard is the back-end tool designed for administrative users to manage the CMX Browser engage experience. It allows the admin users to configure venue-specific menus, banners, and icons as well as content-aware search.
Note Consult your Cisco account team before deploying CMX Browser Engage.
- HTTP Proxy Service—Currently, CMX Dashboard relies on HTTP traffic flows to provide value added services and messages to the customers at the venue. The router intercepts the HTTP traffic and CMX Dashboard inserts a script at the end of the HTTP traffic. The HTTP Proxy is enabled on the MSE. The HTTP Proxy on the MSE terminates all HTTP traffic intercepted using Policy Based Routing (PBR) and acts as a forward proxy by pulling contents on behalf of wireless clients.
Note From Release 7.5 onwards, Cisco engine is used to track clients and tags. If AeroScout engine is detected when you are upgrading from Release 7.2 and later Releases to Release 7.5, then a warning message is displayed about removing the AeroScout license and engine. If you accept, then it removes all the partner engine sub services. If you do not accept the removal of partner engine, then the installation will exit.
Note For ordering information, see the “Licensing Information for MSE” section.
Note Starting from Release 7.4, the evaluation licenses for 100 clients, 100 tags, and 10 wIPS monitor mode access points come standard on each mobility services engine installed for 120 days, which earlier from Release 6.0 till Release 7.3 was installed for 60 days.
Note From Release 7.4 onwards, licensing is going to be AP based and supports 100 AP evaluation license for Connected Mobile Experiences which is limited to 100 elements (clients, tags, interferers, etc combined).
Software Compatibility Matrix
Table 1 lists the MSE converged access solution release compatibility matrix.
Table 2 lists the Cisco MSE and Cisco Wireless Release compatibility matrix.
Note Upgrade from MSE Release 7.5.102.0 to Release 7.6.100.0 is supported.
Cisco MSE and Cisco Converged Access Solution Compatibility Matrix
Table 1 lists the Cisco MSE and Converged Access Solution compatibility matrix.
Note AeroScout CLE is no longer bundled with MSE starting from Release 7.5 Release. However, AeroScout CLE is compatible with MSE Release 7.5 and above using the API interface.
Note Cisco MSE 3310 and 3350 are supported only till Release 7.3.
Note This compatibility matrix lists only the compatibility information of Cisco MSE with other Cisco wireless products. This matrix does not reflect compatibility information between Cisco WLC and Cisco Prime Infrastructure or Cisco NCS. For compatibility information about Cisco Prime Infrastructure with Cisco WLC and other wireless products, see the Cisco Prime Infrastructure Release Notes.
Upgrading the MSE
For instructions on automatically downloading the software using the Prime Infrastructure or for manually downloading the software using a local or remote connection, see the “Updating Mobility Services Engine Software” section in Chapter 2 of the Cisco Mobility Services Engine Getting Started Guide.
You can find these documents at the following URL:
http://www.cisco.com/en/US/products/ps9742/prod_installation_guides_list.html
This section contains the following topics:
- Upgrade Scenarios
- Compressed Software Image
- Updated Software Version Shown in the Prime Infrastructure After Polling
- Base Location, CMX, and wIPS License Requirements
- Licensing Information for MSE
Upgrade Scenarios
The following scenarios are available to upgrade MSE to 7.6 from 7.x releases:
Note Do not run uninstall on the 7.4 or 7.5 Release, instead stop the MSE and directly run the installer.
Upgrading the MSE to 7.6 from 7.x Release Without Data Migration
To upgrade from 7.x release to 7.6.100.0 without data migration, follow these steps:
Step 1
Back up the existing database using the Prime Infrastructure. (We recommended this).
All data existing on the system will be lost and a fresh blank database will be created.
Step 2
Step 3
Step 4
Step 5
- To download software listed in the Prime Infrastructure directory, select the Select from uploaded images to transfer into the Server radio button. Choose a binary image from the drop-down list.
Prime Infrastructure downloads the binary image to the FTP server directory you specified during the Prime Infrastructure installation.
- To use download software available locally or over the network, select the Browse a new software image to transfer into the Server radio button, and click Choose File. Locate the file, and click Open.
Step 6
Step 7
Step 8
Step 9
Step 10
This gives you the following:–
–
–
–
Step 11
Step 12
chmod +x CISCO-MSE-L-K9-7-6-100-0-64bit
Step 13
Step 14
Step 15
Doing so installs the new database using the four .zip files for the database along with the MSE software.
Initial database installation can take a long time (20 minutes at least -or- approximately). Do not cancel the installer midway through the installation process.
Once installed, follow the regular procedure to start, stop, or add an MSE to the Prime Infrastructure.
Note The MSE appliance needs to be rebooted using the “reboot” command before starting the MSE services
Upgrading the MSE to 7.6 from 7.x Release
To upgrade the MSE to 7.6.100.0 from 7.x release, follow these steps:
Note Complete database installation is not required if you are upgrading from 7.0.201.204
Step 1
Step 2
Step 3
Step 4
Step 5
- To download software listed in the Prime Infrastructure directory, select the Select from uploaded images to transfer into the Server radio button. Choose a binary image from the drop-down list.
Prime Infrastructure downloads the binary image to the FTP server directory you specified during the Prime Infrastructure installation.
- To use download software available locally or over the network, select the Browse a new software image to transfer into the Server radio button, and click Choose File. Locate the file, and click Open.
Step 6
Step 7
Step 8
Step 9
Step 10
chmod +x CISCO-MSE-L-K9-7-6-100-0-64bitStep 11
/etc/init.d/msed stopStep 12
/etc/init.d/msed startStep 13
./CISCO-MSE-K9-7-6-100-0-64bitThe installer automatically detects if there is an old database present and asks the relevant questions.
Restoring an Old Database to 7.6
To restore an old database, follow these steps:
Note The regular Restore option on the Prime Infrastructure cannot be used to restore an older database of older releases such as 6.0, 7.0.105.0, or 7.0.110.0 onto 7.6.
Step 1
Step 2
Step 3
Step 4
Step 5
Compressed Software Image
If you download the mobility services engine image *.gz file using the Prime Infrastructure, the mobility services engine automatically decompresses (unzips) it, and you can proceed with the installation as before.
If you manually download the compressed *.gz file using FTP, you must decompress the files before running the installer. These files are compressed under the LINUX operating system and must be decompressed using the gunzip utility program. The unzip method you use is defined by the filename you are trying to unzip.
To make the bin file executable, use the chmod +x filename.bin command.
The MSE virtual appliance software is distributed as an Open Virtualization Archive (OVA) file. You can install the MSE virtual appliance using any of the methods for deploying an OVF. For more information on deploying the MSE virtual appliance, see the Cisco MSE Virtual Appliance Configuration Guide, Release 7.6 .
Updated Software Version Shown in the Prime Infrastructure After Polling
After a software update, the new mobility services engine software version does not immediately appear in mobility services engine queries on the Prime Infrastructure. Up to 5 minutes is required for the new version to appear. Prime Infrastructure, by default, queries the mobility services engine for status every 5 minutes.
Base Location, CMX, and wIPS License Requirements
Client and wIPS licenses are installed from the Prime Infrastructure UI (Administration > License Center). See, Chapter 2: “Adding and Deleting Mobility Services Engines and Licenses” in the Cisco Connected Mobile Experiences Configuration Guide, Release 7.6, Cisco Wireless Intrusion Prevention System, Release 7.6 , and Cisco Location Analytics Configuration Guide, Release 7.6 respectively.
For complete details on ordering and downloading licenses, see the Cisco Mobility Services Engine Licensing and Ordering Guide at the following URL: http://www.cisco.com/en/US/prod/collateral/wireless/ps9733/ps9742/data_sheet_c07-473865.html
Licensing Information for MSE
The Cisco MSE is a platform that enables the wireless network to deliver mobility services in a centralized and scalable way. The MSE delivers the following mobility services:
Note From Release 7.4 onwards, licensing is going to be AP based and not end point based. To accommodate this, new L-LS-licenses are introduced in this release.
- Base Location license: Provides advanced spectrum capability and the ability to detect presence and track rogue device, interferers, Wi-Fi clients and RFID tags. Cisco Base Location also enables third-party solutions that use the MSE API.
- Connected Mobile Experiences (CMX) license: Provides CMX Analytics, CMX Engage, and CMX Connect, as well as all the capabilities of the Base Location license.
- Wireless intrusion prevention system (WIPS): Protects the network from wireless threats, rogue wireless devices, and denial-of-service (DoS) attacks to improve security and meet compliance objectives and has two options:
–
–
Licensing is based on the number of access points in the environment. The licenses are additive.
Note Connected Mobile Experiences licenses will be End of Life with standard 6 months of End of Sales and until then both Connected Mobile Experiences and LS licenses will co-exist.
- Cisco MSE 3355 supports up to 2,500 access points for Base Location/CMX or 6000 access points for wIPS.
- Cisco MSE virtual appliance supports up to 5,000 access points, depending on the server resources for Base Location/CMX or 10,000 access points for wIPS. All licenses are additive. The new scaling numbers for Base Location and CMX licenses are as follows:
–
SKUs for Cisco MSE Location Services
Table 4 lists the Cisco MSE Location Services software licenses.
Note You must select L-MSE-PAK to order these licenses.
Cisco Mobility Services Licenses for High Availability
No separate license is required for high availability. To enable high availability, you need to deploy a primary Cisco MSE appliance with Cisco Connected Mobile Experiences and wIPS licenses, and a secondary Cisco MSE appliance without any Cisco Connected Mobile Experiences or wIPS license.
Table 5 lists the ordering support for physical and virtual appliance.
What’s New in This Release
This section provides a brief description of what is new in Release 7.6. For more information about instruction on how to configure these features, see the Cisco Connected Mobile Experiences Configuration Guide, Cisco Wireless Intrusion Prevention System Configuration Guide, Cisco CMX Analytics Service Configuration Guide, Cisco CMX Browser Engage Service Configuration Guide, and Cisco MSE Virtual Appliance Configuration Guide at
http://www.cisco.com/en/US/products/ps9742/products_installation_and_configuration_guides_list.html
–
–
–
–
–
–
–
–
- AP with Encryption Disabled
- Client with encryption Disabled
- WEP IV key Reused
- Device using open authentication
- Crackable WEP IV key used
- Device using open authentication
- Device using shared key authentication
- AP association capacity full
- Excessive Bandwidth usage
- Excessive multicast/broadcast on channel
- AP overloaded by stations
- AP overloaded by utilization
- Excessive multicast/broadcast on node
- Device unprotected by 802.1x
- 802.1x rekey timeout too long
- Device unprotected by WPA-TKIP
- Device unprotected by PEAP
- WPA or 802.11i Pre-Shared key used
- 802.1x Unencrypted Broadcast or Multicast
- Device unprotected by EAP-FAST
- Device unprotected by IEEE 802.11i/AES
- Device not protected by EAP-TLS
- Device unprotected by EAP-TTLS
- Device unprotected by any selected authentication methods
- Channel or device overload
- Soft AP detection and reporting—A soft AP is a set up on a Wi-Fi adapter without the need of a physical Wi-Fi router. The MSE detects the presence of soft rogue AP and sends response to the Controller for auto containment.
- Good Guy Gone Bad—The MSE detects and reports when a valid client turns into a soft AP for immediate mitigation.
- Enhancement to the display of rogue APs with valid clients—Provides tabular display of all associations between a valid client and the rogue AP.
Important Notes
This section describes the operational notes and navigation changes for Connected Mobile Experiences, wIPS, and the mobility services engine for Release 6.0.103.0 and later releases.
Features and operational notes are summarized separately for the mobility services engine, Connected Mobile Experiences, and wIPS.
Operational Notes for a Mobility Services Engine
This section lists the operational notes for the mobility services engine and contains the following topics:
- How and When to Use the db.tar installer
- Reboot MSE After Fresh Installation or Upgrade
- Automatic Installation Script for Initial Setup
- Parameter Changes During Upgrade from 6.0.x to 7.0.x
- Controller and Associated Mobility Services Engine Must be Mapped to the Same NTP and Prime Infrastructure Server
- Mandatory Default Root Password Change
- Configuring the Prime Infrastructure Communication Username and Password Using MSE setup.sh
- Configuration Changes for Greater Location Accuracy
How and When to Use the db.tar installer
Note You can use the db.tar installer file when you want to install the MSE newly along with the fresh DB installation. The recommended method is to follow the usual Upgrade process unless you want a fresh installation.
Reboot MSE After Fresh Installation or Upgrade
After a new installation or upgrade of the MSE software, you must reboot the MSE using the “reboot” command.
Automatic Installation Script for Initial Setup
An automatic setup wizard is available to help you initially set up the mobility services engine.
An example of the complete automatic setup script is provided in the Cisco Mobility Services Engine Getting Started Guide.
You can find these documents at the following URL:
http://www.cisco.com/en/US/products/ps9742/prod_installation_guides_list.html
Parameter Changes During Upgrade from 6.0.x to 7.0.x
You will notice a change in the tracking limits when you do the following:
1.
Configure tracking limits in 6.0.x.
If limits are greater than licensed counts, limits are removed and licensed counts are enforced instead.
Controller and Associated Mobility Services Engine Must be Mapped to the Same NTP and Prime Infrastructure Server
Communication between the mobility services engine, the Prime Infrastructure, and the controller are in Coordinated Universal Time (UTC). Configuring the Network Time Protocol (NTP) on each system provides devices with the UTC time. An NTP server is required to automatically synchronize time between the controller, Prime Infrastructure, and the mobility services engine.
The mobility services engine and its associated controllers must be mapped to the same NTP server and the same Prime Infrastructure server.
Local time zones can be configured on a mobility services engine to assist network operations center personnel in locating events within logs.
Note You can configure NTP server settings while running the automatic installation script. See the Cisco Mobility Services Engine Getting Started Guide Started Guide for details on the automatic installation script at the following URL:
http://www.cisco.com/en/US/products/ps9742/prod_installation_guides_list.html
Mandatory Default Root Password Change
You must change the default root password of the mobility services engine while running the automatic installation script to ensure optimum network security.
You can also change the password using the Linux passwd command.
Note For the initial login, even if you choose Skip (S), you will be prompted to enter the password. This is because it is mandatory to change the root password at the initial login.
Configuring the Prime Infrastructure Communication Username and Password Using MSE setup.sh
You can configure the Prime Infrastructure Communication username and password using the MSE setup.sh script file.
Scenarios which you might encounter while configuring the Prime Infrastructure username and password are as follows:
- If you configure a new Prime Infrastructure username and password, the password provided is applicable for the new Prime Infrastructure username created.
- If you only configure the Prime Infrastructure username without configuring the Prime Infrastructure password, then the default password admin is applied to the configured username.
- If you only configure the Prime Infrastructure password without configuring the Prime Infrastructure username, then the password for the admin user is changed.
- If you configure an existing username for the Prime Infrastructure username and also configure the password, then the password for that existing user is changed.
Note These users are API users, and they do not have corresponding OS users on the MSE appliance.
Configuration Changes for Greater Location Accuracy
In some RF environments, where location accuracy is around 60 to 70% or where incorrect client or tag floor location map placements occur, you might need to modify the moment RSSI thresholds in the Context Aware Service > Advanced > Location Parameters page on the Prime Infrastructure.
The following RSSI parameters might require modification:
- locp-individual-rssi-change-threshold
- locp-aggregated-rssi-change-threshold
- locp-many-new-rssi-threshold-in-percent
- locp-many-missing-rssi-threshold-in-percent
WSSI Module with 3600 AP
If you are attempting to deploy WSSI module with 3600 APs, then APs should be placed in monitor mode with submode wIPS and advanced wIPS engine enabled on the Prime Infrastructure.
AeroScout Engine Module Changes
Starting Release 7.5, the AeroScout engine module is removed from both the Connected Mobile Experiences setup and location code. During installation, if you are upgrading from Release 7.2 and later to Release 7.5, then you will be prompted to remove the AeroScout engine. If you agree to remove, the it removes the AeroScout engine and by default, the Cisco Tag Engine is started as part of Connected Mobile Experiences. If you do not agree to remove the AeroScout engine, then installation will exit.
Operational Notes for Connected Mobile Experiences
This section lists the operational notes for a mobility services engine and contains the following topics:
- Synchronization Required When Upgrading to Release 7.6 or Importing CAD Floor Images
- Floor Change or Minimum Distance Required for Location Transitions to Post to the History Log
- Non-Cisco Compatible Extensions Tags Not Supported
- Cisco Compatible Extensions Version 1 Tags Required at a Minimum
- Calibration Models and Data
- Advanced Location Parameters
- Location History Time stamps Match Browser Location
- PDAs and Smartphone with Limited Probe Requests Might Affect Location
Synchronization Required When Upgrading to Release 7.6 or Importing CAD Floor Images
When upgrading to Release 7.6 from Release 6.x (and earlier), you must synchronize after the software upgrade and also when CAD-generated floor images are imported into the Prime Infrastructure.
Floor Change or Minimum Distance Required for Location Transitions to Post to the History Log
When history logging is enabled for any or all elements (client stations, asset tags, rogue clients, and access points), a location transition for an element is posted only if it changes floors or the new location of the element is at least 30 feet (10 meters) from its original location.
Note The other conditions for history logging are as follows:
- Clients: Association, authentication, re-association, re-authentication, or disassociation.
- Tags: Tag Emergency button.
- Interferers: Interferer severity change, cluster center change, or merge.
See Services > Mobility Services > Device Name > Context Aware Service > Administration > History Parameters.
Logs can be viewed at Services > Mobility Services > Device Name > Systems > Log.
Non-Cisco Compatible Extensions Tags Not Supported
The mobility services engine does not support non-Cisco CX Wi-Fi tags. Additionally, these non-compliant tags are not used in location calculations or shown on the Prime Infrastructure maps.
Cisco Compatible Extensions Version 1 Tags Required at a Minimum
Only Cisco CX Version 1 (or later) tags are used in location calculations and mapped in the Prime Infrastructure.
Monitoring Information Varies for Clients and Tags
In the Monitor > Clients page (when Location Debug is enabled), you can view information on the last heard access point and its corresponding Received Signal Strength Indicator (RSSI) reading.
Calibration Models and Data
Calibration models always applies to Wireless clients, Interferers, Rogue APs, and Rogue Clients.
See Chapter 7, “Context-Aware Planning and Verification” in the Cisco Connected Mobile Experiences Configuration Guide, Release 7.5 for more details on client calibration.
Advanced Location Parameters
Settings for advanced location parameters related to RSSI, chokepoint usage, location smoothing, and assignment of outside walls on floors, are not applicable to tags.
See the “Editing Advanced Location Parameters” section in Chapter 7 of the Cisco Connected Mobile Experiences Configuration Guide, Release 7.5 .
See Services > Mobility Services > Device Name > Context Aware Service > Advanced > Location Parameters.
Location History Time stamps Match Browser Location
The Prime Infrastructure time stamp is based on the browser location and not on the mobility services engine settings. Changing the time zone on the Prime Infrastructure or on the mobility services engine does not change the time stamp for the location history.
PDAs and Smartphone with Limited Probe Requests Might Affect Location
Many PDAs like smartphones and other Wi-Fi devices with power save mode do not continuously send out probe requests after an initial association to the CUWN. Therefore, calculating the location accuracy of such PDAs using RSSI readings is not always optimal.
Prime Infrastructure Screen and Navigation Changes
- Services replaces Mobility in the Prime Infrastructure navigation bar.
- A centralized license center to install and view license status is available (see Administration > License Center).
- A Switches tab is a new synchronize option to support the new wired Catalyst switch and wired client feature (see Services > Synchronize Services).
Operational Notes for CMX Analytics
This section lists the operational notes for CMX Analytics service and contains the following topics:
WebGL Compatibility
The CMX Analytics in Release 7.5 provides ability to view the analytic results in both 2D (Open Street Maps) and 3D (WebGL) environments. This provides improved understanding of results on multiple floor paths or when dwell times are calculated throughout a multi-storey building. The 3D environment presents the same information as the 2D environment.
WebGL is an advanced feature that provides graphic capabilities. All browsers do not support WebGL on a particular hardware. Verify your browser compatibility in the Get WebGL website. If your browser supports WebGL, then you must see a spinning cube.
If your browser does not support WebGL, you must do the following:
- Update your latest drivers for video card.
- For Google Chrome, follow the instructions given for WebGL and 3D Graphics in the Google Chrome support website.
- For Firefox, follow these steps to enable WebGL:
–
–
–
–
–
–
–
–
Note If your system does not support 3D, then the analytic results are displayed only in 2D Open Street Maps view.
Caveats
This section lists the open caveats in 7.6 for Windows and Linux. For your convenience in locating caveats in Cisco’s Bug Toolkit, the caveat titles listed in this section are taken directly from the Bug Toolkit database. These caveat titles are not intended to be read as complete sentences because the title field length is limited. In the caveat titles, some truncation of wording or punctuation might be necessary to provide the most complete and concise description. The only modifications made to these titles are as follows:
- Commands are in boldface type.
- Product names and acronyms may be standardized.
- Spelling errors and typos may be corrected.
If you are a registered cisco.com user, view Bug Toolkit on cisco.com at the following website:
http://tools.cisco.com/Support/BugToolKit/ .To become a registered cisco.com user, go to the following website:
http://tools.cisco.com/RPF/register/register.doThis section contains of the following topics:
Open Caveats
Table 6 lists the open caveats in the 7.6.100.0 MSE software release.
Resolved Caveats
Table 7 lists the caveats resolved in the 7.6.100.0 MSE software release.
If You Need More Information
If you need information about a specific caveat that does not appear in these release notes, you can use the Cisco Bug Toolkit to find caveats of any severity. Click this URL to browse to the Bug Toolkit:
http://tools.cisco.com/Support/BugToolKit/
(If you request a defect that cannot be displayed, the defect number might not exist, the defect might not yet have a customer-visible description, or the defect might be marked Cisco Confidential.)
Troubleshooting
For the most up-to-date, detailed troubleshooting information, see the Cisco TAC website at the following URL:
http://www.cisco.com/cisco/web/support/index.html
Click Troubleshooting,
choose your product, and then click the Troubleshoot and Alerts heading on the product page to find information on the problem you are experiencing and other service advisories.Related Documentation
The following documents are related to the mobility services engine:
http://www.cisco.com/en/US/products/ps9742/tsd_products_support_series_home.html
http://www.cisco.com/en/US/products/ps9817/products_installation_and_configuration_guides_list.html
http://www.cisco.com/en/US/products/ps9742/products_installation_and_configuration_guides_list.html
http://www.cisco.com/en/US/products/ps9742/products_installation_and_configuration_guides_list.html
http://www.cisco.com/en/US/products/ps9742/products_installation_and_configuration_guides_list.html
http://www.cisco.com/en/US/products/ps9742/prod_installation_guides_list.html
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks . Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
FeedbackContact Cisco
- Open a Support Case
- (Requires a Cisco Service Contract)