show srp

This chapter describes the outputs of the show srp command.

show srp audit-statistics

Table 1. show srp audit-statistics Command Output Descriptions
Field Description

Message statistics

Audit Request

sent

Displays the number of audit requests sent.

received

Displays the number of audit requests received.

dropped

decode error

Displays the number of audit requests dropped due to decode error.

invalid state

Displays the number of audit requests dropped due to invalid state.

Audit Response

sent

Displays the number of audit responses sent.

received

Displays the number of audit responses received.

dropped

decode error

Displays the number of audit responses dropped due to decode error.

invalid state

Displays the number of audit responses dropped due to invalid state.

Session statistics

Audit-2 as standby started at

Displays a time stamp for when the standby chassis audit began and the amount of time it took to finish.

Audit round trip time

Displays audit round trip time.

Audit triggered by switchover

Displays whether audit was triggered by a switchover.

Active sessions

Displays the number of active sessions and their percentage of total calls.

New sessions

Displays the number of new sessions and their percentage of total calls.

Stale sessions

Displays the number of stale sessions and their percentage of total calls.

Inactive sessions

Displays the number of inactive sessions and their percentage of total calls.

Audit-1 as active started at

Displays a time stamp for when the active chassis audit began and the amount of time it took to finish.

Audit round trip time

Displays audit round trip time.

Audit triggered by switchover

Displays whether audit was triggered by a switchover.

Active sessions

Displays the number of active sessions and their percentage of total calls.

New sessions

Displays the number of new sessions and their percentage of total calls.

Stale sessions

Displays the number of stale sessions and their percentage of total calls.

Inactive sessions

Displays the number of inactive sessions and their percentage of total calls.

show srp call-loss statistics

Table 2. show srp call-loss statistics Command Output Descriptions
Field Description

Switchover-n

Identifies the switchover by number.

Started at

Displays the timestamp for when the switchover was initiated.

took

Displays how many seconds the switchover took to finish.

Switchover Reason

Indicates the reason for the switchover:
  • Manual Switchover
  • AAA failure
  • BFD failure
  • BGP failure
  • Chassis-Chassis BFD failure
  • Dead Timer Expiry
  • Diameter failure
  • Dual Active
  • Dual Standby
  • HSRP switchover (WSG/SecGW service only)
  • Not Defined (replaces "Unknown")

Total number of active calls at switchover time

Displays the total number of active calls on this chassis when the switchover was initiated.

Total number of VoLTE capable subscribers

Displays the total number of subscribers with VoLTE capable phones that were on the system when the switchover was initiated.

Total number of subscribers engaged in voice calls

Displays the total number of subscribers that were on voice calls when the switchover was initiated.

Total number of lost calls at switchover time

Displays the number of calls that were lost on this chassis during the switchover.

Chkpt never sent

Displays the total number of checkpoints that were never sent by the chassis during the switchover.

Chkpt failed

Displays the total number of checkpoints that this chassis failed to receive during the switchover.

show srp checkpoint info

Table 3. show srp checkpoint info Command Output Descriptions
Field Description

CMD ID

Displays the checkpoint number associated with the micro-checkpoint.

NAME

Displays the name assigned to the micro-checkpoint.

CRITICAL

Indicates whether or not the micro-checkpoint is in a critical state (Yes or No).

STATS

Indicates whether or not audit statistics are available for the micro-checkpoint (Yes or No).

NACK

Indicates whether or not NACK messaging from the standby chassis has been disabled for the micro-checkpoint (Enable or Disable).

show srp checkpoint statistics

Table 4. show srp checkpoint statistics Command Output Descriptions
Field Description

The following statistics indicates the state of session managers on the chassis. For ideal invocation of SRP procedures, the SessMgr state should *-Connected state.

Number of Sessmgrs

Displays the total number of session managers

Sessmgrs in Active-Connected state

Displays the number of session managers in the active-connected state.

Sessmgrs in Standby-Connected state

Displays the number of session managers in the standby-connected state.

Sessmgrs in Pending-Active state

Displays the number of sessions managers in the pending-active state.

These statistics indicate the conversion status of checkpoint information on the standby chassis.

Current Call Recovery Records (CRRs)

Displays the number of current call recovery records.

Current pre-allocated calls

Displays the number of pre-allocated calls.

The following statistics are indicative of the status of various kinds of SRP message exchanges between active and standby chassis.

Total id-mapping checkpoint rcvd

Displays the total number of id-mapping checkpoints received by the chassis.

Total APN id-mapping chkpnt rcvd

Displays the total number of APN id-mapping checkpoints received by the chassis.

Total SFW id-mapping chkpnt rcvd

Displays the total number of SFW (Stateful Firewall) checkpoints received by the chassis.

Total sync rcvd

Displays the total number of sync messages received by the chassis.

Total sync-ack rcvd

Displays the total number of sync acknowledgement messages received by the chassis.

Total full session checkpoint rcvd

Displays the total number of complete session information checkpoints received by the chassis.

Total nat-ips add rcvd

Displays the total number of NAT IP address additions received by the chassis.

Total nat-ips delete rcvd

Displays the total number of NAT IP address deletions received by the chassis.

Total micro session checkpoint rcvd

Displays the total number of incremental micro session information checkpoints received.

Total inv-crr micro-chkpnt rcvd

Displays the total number of session teardown indication micro-checkpoints received.

total pcrf provided info micro-chkpnt rcvd

Displays the total number of PCRF provided MCC-MNC related information for P-GW and GGSN micro-checkpoints received.

Total call-stats micro-chkpnt rcvd

Displays the total number of call statistics update micro-checkpoints received.

Total nat-ips micro-chkpnt rcvd

Displays the total number of NAT-IP micro-checkpoints received at standby.

Total nat-ips add rcvd

Displays the total number of NAT IP address additions received at standby.

Total nat-ips delete rcvd

Displays the total number of NAT IP address deletions received at standby.

Total nat-port micro-chkpnt rcvd

Displays the total number of NAT port micro-checkpoints received at standby.

Total nat-bypass micro-chkpnt rcvd

Displays the total number of NAT-Bypass Micro-checkpoints received at standby.

Total acs-sess-info micro-chkpnt rcvd

Displays the total number of Active Charging Service (ACS) session information Micro-checkpoints received.

Total dyn-rule micro-chkpnt rcvd

Displays the total number of dynamic rules received and checkpointed to the standby chassis respectively.

Total gx-li micro-chkpnt rcvd

Displays the total number of LI session information, as enabled from Gx, received at standby counter.

Total Instance checkpoint rcvd

Displays the total number of PCRF-generated policy information as received session independent at standby.

Total dyn-rule-instance micro-chkpnt rcvd

Displays the total number of session specific policy received counter.

Total dyn-rule-instance delete micro-chkpnt rcvd

Displays the total number of session specific policy remove counter.

Total dyn-rule-instance ACK rcvd

Displays the total number of session independent information acknowledged from standby counter.

Total id-mapping checkpoint sent

Displays the total number of configuration specific id mapping for VPN/VRF context ids, service ids, and APN ids as sent to standby.

Total APN id-mapping chkpt sent

Displays the total number of configuration specific id mapping for APN ids as sent to standby.

Total SFW id-mapping chkpt sent

Displays the total number of configuration specific id mapping for SFW ids as sent to standby.

Total sync sent

Displays the total number of SYN message received counter.

Total sync-ack sent

Displays the total number of SYN Ack received counter.

Total full session checkpoint sent

Displays the total number of full session checkpoints sent by the chassis.

Total nat-ip add sent

Displays the total number of NAT-IP add sent counter to standby.

Total full chkpnt encoding failures

Displays the total number of complete session information formation failure counter primarily due to release of the session at active

Total micro session checkpoint sent

Displays the total number of micro session checkpoints sent by the chassis.

Total inv-crr micro-chkpnt sent

Displays the total number of invalid CRR micro checkpoints sent.

total pcrf provided info micro-chkpnt sent

Displays the total number of PCRF provided MCC-MNC related information for P-GW and GGSN micro-checkpoints sent.

Total call-stats micro-chkpnt sent

Displays the total number of call statistics micro checkpoints sent.

Total nat-ip micro-chkpnt sent

Displays the total number of NAT-IP Micro-checkpoint sent from active.

Total nat-ip add sent

Displays the total number of NAT-IP address addition indications to standby.

Total nat-ip delete sent

Displays the total number of NAT-IP address deletion indications to standby.

Total nat-port micro-chkpnt sent

Displays the total number of NAT-Port Micro-checkpoint sent from active.

Total nat-bypass micro-chkpnt sent

Displays the total number of NAT-Bypass Micro-checkpoint sent from active.

Total acs-sess-info micro-chkpnt sent

Active Charging Service (ACS) specific session information as sent to standby.

Total dyn-rule micro-chkpnt sent

Displays the total number of dynamic rules sent and checkpointed to the standby chassis respectively.

Total gx-li micro-chkpnt sent

LI session information sent from active.

Total instance micro-chkpnt sent

PCRF generated policy information as sent session independent from active.

Total dyn-rule-instance micro-chkpnt sent

Session specific policy add sent counter at active.

Total dyn-rule-instance delete micro-chkpnt sent

Session specific policy remove sent counter from active.

Total dyn-rule-instance ACK sent

Session independent information acknowledgements sent from standby counter.

Total micro chkpnt encoding failures

Incremental session information failed to be sent due to bad encoding at active.

Total instance micro chkpnt encoding failures

PCRF generated policy encoding failed while being sent session independent from active.

Total ipsec non urgent micro-chkpnt rcvd from active chassis serial number mismatch

Non-urgent IPsec mircro-checkpoint received from Active Chassis with serial number mismatch.

Total ipsec urgent micro-chkpnt rcvd from active chassis serial number mismatch

Urgent IPsec mircro-checkpoint received from Active Chassis with serial number mismatch.

sessmgr --> ipsecmgr checkpoint queue stats

Displays sessmgr to ipsecmgr queue statistics.
  • Imgr
  • QFull
  • UQFull (Urgent Queue)
  • QLen
  • UQLen
  • QSent
  • UQSent
  • TotalMsgSent

sessmgr --> aaamgr ipsec checkpoint queue stats

Displays sessmgr to aaamgr queue statistics.gr to ipsecmgr queue statistics.
  • Amgr
  • QFull
  • UQFull (Urgent Queue)
  • QLen
  • UQLen
  • QSent
  • UQSent
  • TotalMsgSent

Total micro-chkpnt to send dropped full-chkpnt not sent

Displays number of unsent micro- checkpoints due to dropped full checkpoints.

Total micro-chkpnt to send dropped srp state not active

Displays number of unsent micro- checkpoints that were dropped because SRP state was not Active.

Total micro-chkpnt to send deleted from chkpnt queue

Displays number of unsent micro-checkpoints that were deleted from the checkpoint queue.

Session full checkpoint never sent

Displays the number of calls which failed to send out complete session information.

Total Macro chkpnt Nack Sent

Displays the number of NACKs sent from Standby due to macro-checkpoint failure.

Total Micro chkpnt Nack Sent

Displays the number of NACKs sent from Standby due to micro-checkpoint failure.

Coherency_key mismatch

Displays the number of NACKs sent from Standby due to micro-checkpoint failure with reason coherency_key mismatch.

Micro-Checkpoint failed to apply

Displays the number of NACKs sent from Standby due to micro-checkpoint failure with reason application failure.

Session Not Found

Displays the number of NACKs sent from Standby due to micro-checkpoint failure with reason session failure.

Total Macro chkpnt Nack Rcvd:

Displays the number of NACKs received from Standby due to macro-checkpoint failure.

Total Micro chkpnt Nack Rcvd

Displays the number of NACKs received from Standby due to micro-checkpoint failure.

Coherency_key mismatch

Displays the number of NACKs received from Standby due to micro-checkpoint failure with reason coherency_key mismatch.

Micro-Checkpoint failed to apply

Displays the number of NACKs received from Standby due to micro-checkpoint failure with reason application failure.

Session Not Found

Displays the number of NACKs received from Standby due to micro-checkpoint failure with reason session failure.

Standby call pre-alloc failures

Displays the number of standby call pre allocation failures.

table-id mapping failures

Displays the number of table id mapping failures.

vpn-id mapping failures

Displays the number of decode failures due to not finding matching vpn information on standby.

svc-id mapping failures

Displays the number of decode failures due to not finding matching service information on standby.

ntwk-id mapping failures

Displays the number of decode failures due to not finding matching ggsn network information on standby.

demux-mapping-id failures

Displays the number of decode failures due to not finding matching demux information on standby.

tpo-policy-mapping-id failures

NOTE: The Traffic Performance Optimization (TPO) in-line service is not supported in this release.

aaa session failures

Displays the number of AAA session failures.

recovery record alloc failures

Displays the number of recovery record allocation failures.

pre-allocate vpnmgr failure

Pre-allocation of callines at standby failed due to VPN IP address allocation.

Ipv4 failure

Pre-allocation of callines at standby failed due to VPN IPv4 address allocation.

Ipv4 Prefix failure

Pre-allocation of callines at standby failed due to VPN IPv4 prefix address allocation.

Ipv6 failure

Pre-allocation of callines at standby failed due to VPN IPv6 address allocation.

pre-allocate vpnmgr msg failure

Pre-allocation of callines at standby failed due to VPN messaging issues.

pre-allocate demuxmgr failure

Pre-allocation of callines at standby failed due to demux failure.

pre-allocate demuxmgr msg failure

Pre-allocation of callines at standby failed due to demux messaging issues.

Standby micro-checkpoint failures

Displays the number of standby micro checkpoint failures.

recovery record not found

Displays the number of recovery records not found.

nat-ip uchkpt failed

The number of NAT IP micro-checkpoint failures.

nat-port uchkpt failed

The number of NAT port micro-checkpoint failures.

nat-bypass uchkpt failed

The number of NAT bypass micro-checkpoint failures.

The following are audit statistics done as part of the switchover--conversion of session information failures as reported at standby going active.

Total CRR recovery failures

Displays the total number of Call Recovery Record (CRR) call recovery failures.

audit-npumgr-failure

Audit of npumgr failures.

audit-npumgr-nat-flow-failure

Audit of npumgr NAT flow failures.

audit-npumgr-nat-bypass-flow-failure

Audit of npumgr NAT bypass flow failures.

audit-vpnmgr-failure

Audit of vpnmgr failures.

audit-vpnmgr-nat-ip-failure

Audit of vpnmgr NAT IP failures.

audit-demuxmgr-failure

Audit of demuxmgr failures for all demux managers.

For the next three audit statistics, if all three audits fail for a single call, only the counter for the first failure will be incremented. Total audit failure count will remain one (not three). There is no double counting.

audit-egtpinmgr-imsi-failure

Audit of EGTP inbound IMSI failures following an Interchassis Session Recovery (ICSR) switchover.

audit-egtpinmgr-gtpc-failure

Audit of EGTP inbound GTPC failures following an ICSR switchover.

audit-gtpumgr-failure

Audit of gtpumgr failures following an ICSR switchover.

audit-aaamgr-failure

Audit of aaamgr failures.

audit-ipsecmgr-failure

Audit of ipsecmgr failures.

audit-dgmbmgr-failure

Audit of dgmbmgr failures.

audit-mcast-proxy-failure

Audit of mcast proxy failures.

audit-igmp-proxy-failure

Audit of igmp proxy failures.

audit-unsupported-sess-type

Audit of unsupported session type failures.

recovery-unspecified-fail

The call recovery failed due to unspecified reason.

recovery-invalid-crr

The call recovery failed due to invalid CRR.

recovery-missing-info

The call recovery failed due to missing information.

recovery-quota-reached

The call recovery failed due to quota reached.

recovery-set-acs-sess-info-failure

The call recovery failed due to set ACS session information.

recovery-acs-sfw-policy-failure

The call recovery failed due to ACS SFW policy.

recovery-ucheckpt-failure

The call recovery failed due to Micro-checkpoint.

recovery-service-not-found

The call recovery failed due to service not found.

recovery-restart-counter-mismatch

The call recovery failed due to restart counter mismatch.

recovery-aaa-sub-session-mismatch

The call recovery failed due to aaa sub session mismatch.

recovery-crr-no-aaa-session

The call recovery failed due to CRR no aaa session.

recovery-crr-aaa-session-not_found

The call recovery failed due to CRR aaa session not found.

recovery-flow-buffer-null

The call recovery failed due to flow buffer null.

recovery-invalid-flow-id

The call recovery failed due to invalid flow ID.

recovery-flow-id-in-use

The call recovery failed due to flow ID in use.

recovery-callline-alloc-failure

The call recovery failed due to callline allocation.

recovery-ipv6-session-alloc-failure

The call recovery failed due to IPv6 session allocation.

recovery-no-apn-group-stats-entry

The call recovery failed due to no APN group statistics.

recovery-apply-aaa-config-failure

The call recovery failed due to application of aaa configuration.

recovery-sub-session-alloc-failure

The call recovery failed due to sub session allocation.

recovery-nat-failure

The call recovery failed due to NAT.

recovery-set-dst-vpn-failure

The call recovery failed due to set destination VPN.

recovery-vpn-not-found

The call recovery failed due to VPN not found.

recovery-access-side-failure

The call recovery failed due to access side.

recovery-network-side-failure

The call recovery failed due to network side.

recovery-peer-callline-failure

The call recovery failed due to peer callline.

recovery-li-failure

The call recovery failed due to LI.

recovery-css-failure

The call recovery failed due to CSS.

recovery-uchkpt-alloc-failure

The call recovery failed due to Micro-checkpoint allocation.

recovery-acs-dyn-rule_failure

The call recovery failed due to ACS dynamic rule.

recovery-acs-acct-rule-failure

The call recovery failed due to ACS account rule.

recovery-prepaid-failure

The call recovery failed due to prepaid.

recovery-mipfa-failure

The call recovery failed due to mipfa.

call-recovery-stale-session

The call recovery failed due to stale session.

call-recovery-wrong-flow-type

The call recovery failed due to wrong flow type.

call-recovery-null-acct-session

The call recovery failed due to null account session.

call-recovery-wrong-acct-session-type

The call recovery failed due to wrong account session type.

call-recovery-null-acct-session

The call recovery failed due to null accounting session.

call-recovery-wrong-acct-session-type

The call recovery failed due to wrong type of accounting session.

recovery-acs-acct-dyn-chrg-update-qg-failure

The call recovery failed due to an ACS accounting dynamic charging QG update failure.

recovery-acs-acct-dyn-chrg-update-ca-failure

The call recovery failed due to an ACS dynamic charging CA update failure.

call-recovery-acs-internal-audit-failure

The call recovery failed due to an ACS internal audit failure.

Total CRR replace record

Total number of replaced CRRs (Call Recovery Records).

call-recovery-gtpu-teid-in_use

The call recoveries for in-use GTPU TEIDs (Tunnel Endpoint IDs).

call-recovery-egtpc-teid-in_use

The call recoveries for in-use EGTPC TEIDs.

NAT-NPU flow audit failures

The number of NAT NPU Flow audit failures.

NAT-IP Pool address audit failures

The number of NAT IP Flow audit failures.

NAT-Bypass flow audit failures

The number of NAT Bypass Flow audit failures.

Graceful call drops during audit failure

The number of calls dropped as a result of Audit Failure with require graceful-cleanup-during-audit-failure enabled.

show srp info

Table 5. show srp info Command Output Descriptions
Field Description

Service Redundancy Protocol

Context

Displays the srp context configured for service redundancy protocol. Only one context may be configured with this service.

Local Address

Displays the local address of the chassis.

Chassis State

Displays the chassis state (init, standby or active).

Chassis Mode

Displays the chassis mode (primary or backup).

Chassis Priority

Displays the chassis priority. The chassis priority is an integer that determines which chassis is in the active state. The lower number has a higher priority. The priority must be an integer from 1 through 255. Default is 125.

Local Tiebreaker

Displays the MAC address which is used to determine priority when both chassis have the same priority and route modifier. The lower MAC address has the higher priority.

Route-Modifier

Displays the modifier which is used to determine which chassis has priority. The lower the number the higher the priority.

DSCP Markings

Displays current settings for DSCP marking of SRP messages.

 Control

Displays DSCP value set for SRP control messages.

 Session

Displays DSCP value set for SRP checkpoint messages (session maintenance).

Peer Remote Address

Displays the IP address of the remote peer.

Peer State

Displays whether the peer is in the active or standby state.

Peer Mode

Displays the peer mode (standby or active).

Peer Priority

Displays the peer priority (primary or backup).

Peer Tiebreaker

Displays the peer MAC address.

Peer Route-Modifier

Displays the peer's BGP route modifier.

Last Hello Message received

Displays a time stamp for the most recent hello message that was received.

Peer Configuration Validation

Displays the peer configuration validation.

Last Peer Configuration Error

Displays the most recent error that was received when the chassis was not able to validate its peer configuration.

Last Peer Configuration Event

Displays a time stamp for the last peer configuration event.

Last Validate Switchover Status

Displays whether both active and standby systems are ready for a planned srp switchover.

Connection State

Displays the status of the redundancy link between the two chassis.

Next Peer Audit Scheduled

Displays minutes and seconds until next audit.

Peer Audit State

Displays current state of peer audit configuration.

Last Peer Audit Type

Displays the type of peer audit that was last run.

Last Peer Audit Successful

Indicates whether or not the last peer audit was successfully completed.

Feature    Configured-status   Operational-status

  allow-volte-data-traffic

Indicates system-level Configuration and Operational status of this feature as Enabled, Disabled or Mismatch.

  allow-all-dat-traffic

Indicates system-level Configuration and Operational status of this feature as Enabled, Disabled or Mismatch.

show srp monitor

Table 6. show srp monitor Command Output Descriptions
Field Description

Type:

(A) = Authentication Probe

(B) = BGP

(D) = Diameter

(F) = Bidirectional Forwarding Detection

State:

(I) = Initializing

(U) = Up

(D) = Down

GroupId

SRP Peer Group Identifier (displayed as an integer from 0 through 9. Default = 0).

Auth. probe monitor

Displays the following authentication probe information:

IP addr = IP address in IPv4 or IPv6 notation

Port = Port number

Context (VRF Name)

Last

Update

(AU) Auth. probe monitors up

Displays the number of authentication probe monitors in the active state.

(AD) Auth. probe monitors down

Displays the number of authentication probe monitors in the inactive state.

(AI) Auth. probe monitors init

Displays the number of authentication probe monitors in the initializing state.

BFD monitor

Displays BFD information.

(FU) BFD monitors up

Displays the number of BFD monitors in the active state.

(FD) BFD monitors down

Displays the number of BFD monitors in the inactive state.

(FI) BFD monitors init

Displays the number of BFD monitors in the initializing state.

BGP monitor state

Displays the following BGP information:

  • IP addr = IP address in IPv4 or IPv6 notation

  • Port = Port number

  • Context (VRF Name)

  • Last

  • Update

(BU) BGP monitors up

Displays the number of BGP monitors in the active state.

(BD) BGP monitors down

Displays the number of BGP monitors in the inactive state.

(BI) BGP monitors init

Displays the number of BGP monitors in the initializing state.

DIAMETER monitor state

Displays the following Diameter server information:

  • Context

  • Endpoint Name

  • IPAddr (port)/FQDN

  • Last

  • Update

(DU) DIAMETER monitors up

Displays the number of Diameter monitors in the active state.

(DD) DIAMETER monitors down

Displays the number of Diameter monitors in the inactive state.

(DI) DIAMETER monitors init

Displays the number of Diameter monitors in the initializing state.

show srp statistics

Table 7. show srp statistics Command Output Descriptions
Field Description

Service Redundancy Protocol

Peer Remote Address

The IP address for the redundant peer chassis.

Hello Messages Sent

The number of hello messages that were sent to the peer chassis.

Hello Message Received

The number of hello messages received from the peer chassis.

Hello Messages Discarded

The number of discarded hello messages.

Configuration Validation Messages Sent

The number of configuration validation messages sent to the peer.

Configuration Validation Message Received

The number of configuration validation messages received from the peer chassis.

Configuration Validation Messages Discarded

The number of discarded configuration validation messages.

Resource Messages Sent

The number of resource messages sent to the peer chassis.

Resource Messages Received

The number of resource messages received from the peer chassis.

Resource Messages Discarded

The number of discarded resource messages.

Switchover Req Messages Sent

The number of switchover request messages sent to the peer chassis.

Switchover Req Messages Received

The number of switchover request messages received from the peer chassis.

Switchover Rsp Messages Sent

The number of switchover response messages sent to the peer chassis.

Switchover Rsp Messages Received

The number of switchover response messages received from the peer chassis.

Switchover Messages Discarded

The number of discarded switchover messages.

Switchover Events

The number of switchover events, where one chassis went from active to inactive and the other chassis went from inactive to active.

Chunk Data Messages Sent

Free chunks information sent from the Active CP.

Chunk Data Messages Received

Free chunks information received from the Active CP.

Chunk Data Messages Discarded

Free chunks information discarded on the Active and Standby CPs.

CMP Data Messages Sent

The number of Certificate Management Protocol (CMP) data messages sent. (RFC 4210)

CMP Data Messages Received

The number of CMP data messages received.