Declarations of Conformity and Regulatory Information

This section provides declarations of conformity and regulatory information for the . You can find additional information at: https://www.cisco.com/c/dam/assets/prod/wireless/wireless-compliance-tool/index.html.

Manufacturers Federal Communication Commission Declaration of Conformity Statement



Access Point model

Certification number

CW9174I

UDX-600218010

Manufacturer:

Cisco Systems, Inc.170 West Tasman Drive San Jose, CA 95134-1706 USA

This device complies with Part 15 rules. Operation is subject to the following conditions:

  1. This device may not cause harmful interference.

  2. This device must accept any interference received, including interference that may cause undesired operation.

  3. For 6 GHz operation, this device includes authorization for both Low Power Indoor (LPI) operation and Standard Power (SP) operation, as permitted by the applicable FCC regulatory grant. LPI operation is restricted to indoor use only. Standard Power operation is permitted only when operating under Automated Frequency Coordination (AFC) and in accordance with applicable regulatory grant and deployment requirements.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna

  • Increase separation between the equipment and receiver

  • Connect the equipment to an outlet on a circuit different from which the receiver is connected

  • Consult the dealer or an experienced radio/TV technician

  • This device is intended for professional installation and must be installed and configured in accordance with Cisco instructions and applicable regulatory requirements


Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

6 GHz operating class restrictions

These restrictions apply to 6 GHz operation based on the operating class (LPI or SP):

Low Power Indoor (LPI) Access Points

  • FCC regulations restrict Low Power Indoor (LPI) operation to indoor use only.

  • LPI operation is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation is permitted in large aircraft flying above 10,000 feet in the 5.925-6.425 GHz band.

  • Transmitters in the 5.925-7.125 GHz band are prohibited from operating to control or communicate with unmanned aircraft systems.

Standard Power (SP) Access Points

  • Operation is prohibited on oil platforms, cars, trains, boats, and aircraft.

  • Standard Power operation is permitted only under Automated Frequency Coordination (AFC) and in accordance with applicable regulatory grant and deployment requirements.

VCCI Statement for Japan

Warning

Warning

 

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.



Warning

 


Access Point model:

CW9174I

Guidelines for Operating Cisco Wireless Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco Wireless access points in Japan. These guidelines are provided in both Japanese and English.

この機器の使用周波数帯では、電子レンジ等の産業・科学・医療用機器のほかエ場の製造ライン等で使用されている移動体識別用の構内無線局（免許を要する無線局）及び特定小電力無線局（免許を要しない無線局）が運用されています。

  1. この機器を使用する前に、近くで移動体臓別用の構内無線局及び特定小電力無線局が運用されていないことを確認して下さい。

  2. 万一、この機器から移動体識別用の構内無線局に対して電波干渉の事例が発生した場合には、速やかに使用周波数を変更するか又は電波の発射を停止した上、下記連絡先にご連絡頂き、混信回避のための処置等（例えぱ、ノくーティションの設置など｝Iこついてご相談して下さい。

  3. その他、この機器から移動体撒別用の特定，ト電力無線局に対して電波干渉の事例が発生した場合など何かお困りのことが起きたときは、次の連絡先へお問い合わせ下さい。

    連絡先：03-6434-6500

English Translation

This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.

  1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.

  2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.

  3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.

    Contact Number: 03-6434-6500

Canadian Compliance Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  • This device may not cause interference.

  • This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

  • L’appareil ne doit pas produire de brouillage.

  • L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Wi-Fi 7 Device (6 GHz Band)

Operation in the 6 GHz band is subject to the following restrictions:

  • Operation shall be limited to indoor use only.

  • Devices shall not be used for control of or communications with unmanned aircraft systems.

  • Devices shall not be used on oil platforms.

  • Devices shall not be used on automobiles.

  • Devices shall not be used on trains.

  • Devices shall not be used on maritime vessels.

  • Devices shall not be used on aircraft, except for low-power indoor access points and indoor subordinate devices operating in the 5925–6425 MHz band, which may be used on large aircraft as defined in the Canadian Aviation Regulations, while flying above 3,048 metres (10,000 feet).

Appareil Wi-Fi 7 (bande de 6 GHz)

Le fonctionnement dans la bande de 6 GHz est soumis aux restrictions suivantes:

  • Utilisation limitée à l’intérieur seulement.

  • Les dispositifs ne doivent pas être utilisés pour commander des systèmes d’aéronef sans pilote ni pour communiquer avec de tels systèmes.

  • Les dispositifs ne doivent pas être utilisés sur les plateformes de forage pétrolier.

  • Les dispositifs ne doivent pas être utilisés dans les automobiles.

  • Les dispositifs ne doivent pas être utilisés dans les trains.

  • Les dispositifs ne doivent pas être utilisés sur les navires maritimes.

  • Les dispositifs ne doivent pas être utilisés dans les aéronefs, à l’exception des points d’accès intérieurs de faible puissance et des dispositifs subordonnés intérieurs fonctionnant dans la bande de 5925 à 6425 MHz, qui peuvent être utilisés dans les gros aéronefs tel que défini dans le Règlement de l’aviation canadien, lorsqu’ils volent à une altitude supérieure à 3,048 mètres (10,000 pieds).

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

The transmitter module may not be co-located with any other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.

Low power indoor access points and indoor subordinate devices

  • Operation shall be limited to indoor use only.

  • Le fonctionnement doit être limitée à une utilisation à l'intérieur seulement.

Standard client devices

  • The antenna height shall be determined by the installer or operator of the standard-power access point or fixed client device, or by automatic means. This information shall be stored internally in the device. Provision of accurate device information is mandatory. Information for antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 4.5.4 (c) shall be clearly indicated.

  • La hauteur de l'antenne doit être déterminée par l'installateur ou l'opérateur du point d'accès de puissance normale ou du dispositif client fixe, ou par des dispositifs automatiques. Cette information doit être enregistrée dans le dispositif. La fourniture d'information précise sur le dispositif est obligatoire. le ou les types d'antennes, le ou les modèles d'antennes et le ou les pires angles d'inclinaison nécessaires pour rester conforme à l'exigence de la section 4.5.4 c. s'appliquant au masque de p.i.r.e. doivent être clairement indiqués.

Industry Canada

Access Point model

Certification number

CW9174I

6961A-600218010

European Community, Switzerland, Norway, Iceland, and Liechtenstein Compliance

The product carries the CE Mark:



This device is restricted to indoor use only when operating in the following frequency ranges:

  • 5150–5350 MHz

  • 5945–6425 MHz

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm (7.87 inches) between the radiator and your body.

This equipment is intended for use in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.


Note
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.

Access Point model:

CW9174I

Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

United Kingdom Compliance

This device is restricted to indoor use only when operating in the following frequency ranges:

  • 5150–5350 MHz

  • 5945–6425 MHz

This equipment should be installed and operated with a minimum distance of 20 cm (7.87 inches) between the radiator and your body.

Access Point Model:

CW9174I

Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

Administrative Rules for Cisco Wireless Access Points in Taiwan

This section provides administrative rules for operating Cisco Wireless access points in Taiwan. The rules are provided in both Traditional Chinese and English.

Traditional Chinese Translation

【低功率射頻器材技術規範】取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。應避免影響附近雷達系統之操作。

【本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者】

English Translation

Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power, or alter original characteristics or performance of approved low power radio-frequency devices.

Low power radio-frequency devices shall not affect aircraft safety or interfere with legal communications. If interference is observed, operation shall be immediately discontinued until the condition is resolved.

Legal communications refer to radio communications operated in accordance with the Telecommunications Management Act. Low power radio-frequency devices must accept interference from legal communications or ISM radio wave radiated devices.

Operation should avoid affecting nearby radar syste

Access Point model

Certification number

CW9174I

TBD

Professional installation requirement

This device must be installed and configured by professional personnel.

This device is not intended for direct sale to the general public.

Operation of Cisco Wireless Access Points in Brazil

Figure 1. Brazil Regulatory Information

This section contains special information for operation of Cisco Wireless Access Points in Brazil.

Portuguese

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.

English

This equipment is not entitled to protection from harmful interference and may not cause interference to duly authorized systems.

equipamento Wi-Fi 7

O uso deste equipamento é restrito a ambientes fechados.

A operação é proibida em plataformas petrolíferas, automóveis, trens, embarcações e aeronaves, exceto em aeronaves de grande porte voando acima de 3.048 metros (10.000 pés).

Wi-Fi 7 Device

Operation of this device is restricted to indoor use only.

Operation is prohibited on oil platforms, automobiles, trains, maritime vessels, and aircraft, except on large aircraft operating above 3,048 meters (10,000 feet).

Access Point model

Certification number

CW9174I

TBD

Declaration of conformity for RF exposure

This section provides information on compliance with applicable regulatory requirements and international guidelines related to human exposure to radio frequency (RF) electromagnetic fields.

The Cisco CW9174I access point is designed to comply with applicable RF exposure requirements established by regulatory authorities and recognized international standards, including but not limited to:

  • United States: 47 CFR Part 2, Subpart J

  • Canada: Innovation, Science and Economic Development Canada (ISED) Safety Code 6

  • European Union: Council Recommendation 1999/519/EC and applicable EN standards based on ICNIRP guidelines

  • International: International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines

  • Australia: Applicable Australian Radiation Protection standards

To ensure compliance with these requirements, the Cisco CW9174I shall be installed and operated using Cisco-approved antennas and accessories only. The device is intended to be installed in a manner that maintains a minimum separation distance of 20 cm (7.87 inches) between the radiating elements and all persons during normal operation, unless otherwise specified by applicable regional regulations.

The CW9174I includes radio transmitters and receivers and is designed to operate within established RF exposure limits, which incorporate substantial safety margins to ensure protection for all persons, regardless of age or health condition.

This device meets applicable international guidelines for exposure to radio frequency electromagnetic fields

The Cisco CW9171I device contains radio transmitters and receivers and is designed to operate within the limits for human exposure to radio waves established by applicable regulatory authorities and recognized international guidelines, which incorporate substantial safety margins to ensure the safety of all persons, regardless of age or health condition.

To maintain compliance with these requirements, the device shall be installed and operated in a manner that prevents direct contact with the antennas by the end user and maintains a minimum separation distance of 20 cm (7.87 inches) between the radiating elements and all persons during normal operation, unless otherwise specified by applicable regional regulations.

Separation Distance

20 cm (7.87 inches)

RF Exposure Compliance (FCC/ISED/International)

This device meets applicable regulatory requirements and international guidelines for human exposure to radio frequency electromagnetic fields.

The Cisco CW9171I access point contains radio transmitters and receivers and is designed to operate within the limits for RF exposure established by the Federal Communications Commission (FCC), Innovation, Science and Economic Development Canada (ISED), and other applicable regulatory authorities. These limits incorporate substantial safety margins to ensure the safety of all persons, regardless of age or health condition.

To maintain compliance with these requirements, the device shall be installed and operated in a manner that prevents direct contact with the antennas by the end user and maintains a minimum separation distance of 20 cm (7.87 inches) between the radiating elements and all persons during normal operation, unless otherwise specified by applicable regional regulations.

The device has been evaluated and found compliant with the applicable RF exposure requirements as part of the radio certification process.

Table 1. Minimum Separation Distance

Frequency Band

Minimum Separation distance

2.4 GHz / 5 GHz / 6 GHz

20 cm (7.87 inches)

Conformité à l’exposition aux radiofréquences – Canada

Cet appareil est conforme aux exigences réglementaires applicables et aux directives internationales en matière d’exposition humaine aux champs électromagnétiques de radiofréquence.

L’appareil Cisco CW9171I comprend des émetteurs et récepteurs radio et a été conçu pour fonctionner dans les limites d’exposition aux radiofréquences établies par Innovation, Sciences et Développement économique Canada (ISDE), notamment le Code de sécurité 6 de Santé Canada, ainsi que par d’autres autorités réglementaires applicables. Ces limites intègrent des marges de sécurité importantes afin d’assurer la protection de toutes les personnes, indépendamment de l’âge ou de l’état de santé.

Afin de maintenir la conformité à ces exigences, l’appareil doit être installé et utilisé de manière à empêcher tout contact direct entre les antennes et l’utilisateur final, et à maintenir la distance minimale d’éloignement indiquée ci-dessous entre les éléments rayonnants et toute personne durant le fonctionnement normal, sauf indication contraire prévue par les réglementations régionales applicables.

Table 2. Distance minimale d’éloignement

Bande de fréquences

Distance minimale d’éloignement

2.4 GHz / 5 GHz / 6 GHz

20 cm (7.87 inches)

Note

Remarque : La distance minimale d’éloignement s’applique à toutes les bandes de fréquences prises en charge durant le fonctionnement normal, sauf indication contraire prévue par les réglementations régionales applicables.

Additional information on RF exposure

You can find additional information on the subject at the following links:

You can obtain additional information from the following organizations:

Declaration of Conformity Statements

All the Declaration of Conformity statements related to this product can be found at the following location: https://pas.cisco.com/pdtcnc/#/