Full Cisco Trademarks with Software License
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)
About The Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms
The Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms are best-of-breed, 5G-ready, cloud edge platforms designed for accelerated services, multi-layer security, cloud-native agility, and edge intelligence to accelerate your journey to cloud.
Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms with Cisco IOS XE SD-WAN Software deliver Cisco’s secure, cloud-scale SD-WAN solution for the branch. The Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms are built for high performance and integrated SD-WAN Services along with flexibility to deliver security and networking services together from the cloud or on premises. It provides higher WAN port density and a redundant power supply capability. The Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms have a wide variety of interface options to choose from—ranging from lower and higher module density with backward compatibility to a variety of existing WAN, LAN, voice, and compute modules. Powered by Cisco IOS XE, fully programmable software architecture, and API support, these platforms can facilitate automation at scale to achieve zero-touch IT capability while migrating workloads to the cloud. The Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms also come with Trustworthy Solutions 2.0 infrastructure that secures the platforms against threats and vulnerabilities with integrity verification and remediation of threats.
The Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms are well suited for medium-sized and large enterprise branch offices for high WAN IPSec performance with integrated SD-WAN services.
For more information on the features and specifications of Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms, refer to the Cisco Catalyst 8300 Series Edge platforms datasheet.
 Note |
Sections in this documentation apply to all models of Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms unless a reference to a specific model is made explicitly. |
Note |
Cisco IOS XE 17.13.1a is the first release for the Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms in the Cisco IOS XE 17.13.x release series. |
Product Field Notice
Cisco publishes Field Notices to notify customers and partners about significant issues in Cisco products that typically require an upgrade, workaround or other user action. For more information, see https://www.cisco.com/c/en/us/support/web/field-notice-overview.html.
We recommend that you review the field notices to determine whether your software or hardware platforms are affected. You can access the field notices from https://www.cisco.com/c/en/us/support/web/tsd-products-field-notice-summary.html#%7Etab-product-categories.
New and Changed Hardware and Software Features
Feature Navigator
You can use Cisco Feature Navigator (CFN) to find information about the software features, platform, and software image support on Cisco Catalyst 8200 and Catalyst 8300 Series Edge Platforms. To access Cisco Feature Navigator, go to https://cfnng.cisco.com/.
Note |
To access CFN, you do not require an account on cisco.com. |
New and Changed Hardware Features
There are no new hardware features in this release.
New and Changed Software Features in Cisco IOS XE 17.13.1a
|
Feature |
Description |
|---|---|
|
The Application Performance Monitor feature introduces a simplified framework that enables you to configure intent-based performance monitors. With this framework, you can view real-time, end-to-end application performance filtered by client segments, network segments, and network segments. |
|
|
Cisco SD-Routing Cloud OnRamp for Multicloud extends enterprise WAN to public clouds. This multicloud solution helps to integrate public cloud infrastructure into the Cisco Catalyst SD-Routing devices. With these capabilities, the devices can access the applications hosted in the cloud. |
|
|
|
|
This feature introduces support for configuring retry time intervals for GARP messages on the BD-VIF interface. You can configure this feature using the global ip arp nat-garp-retry and ip nat inside source static commands. |
|
|
The SD-Routing Configuration Group feature provides a simple, reusable, and structured method to configure the SD-Routing device using Cisco Catalyst SD-WAN Manager. |
|
|
From Cisco IOS XE 17.13.1a, Segment Routing is supported over the IPv6 dataplane for Border Gateway Protocol (BGP) on L3VPN networks using On-Demand Next Hop (ODN). |
|
|
Cisco SD-WAN Manager allows you to measure the network speed and available bandwidth between adevice and an iPerf3 server. The speed tests measure upload speed from the source device to the selected or specified iperf3 server, and measure download speed from the iperf3 server to the source device. |
|
|
With this feature, you can schedule software image upgrade on Cisco SD-Routing devices. This allows you to avoid any downtime due to the software upgrade process. |
|
|
Support for Flexible NetFlow Application Visibility on SD-Routing Devices |
The Flexible NetFlow (FNF) feature provides statistics on packets flowing through the device and helps to identify the tunnel or service VPNs. Also, it provides visibility for all the traffic that passes through the VPN0 on Cisco SD-Routing devices by using the SD-Routing Application Intelligence Engine (SAIE). |
|
This feature allows you to configure options to capture the bidirectional IPv6 traffic data to troubleshoot connectivity on the SD-Routing devices. |
|
|
From IOS XE 17.13.1a, the device maintains the neighbor information even after the session is terminated. To configure this, use the bgp listen persistent command for all dynamic neighbors and bgp listen range peer-group persistent command for specific neighbors. |
|
|
This enhancement introduces support for Suite B ciphers with GET VPN on the following router models:
|
|
|
SELinux (Security-Enhanced Linux) is a solution designed to incorporate a strong, flexible mandatory access control (MAC) architecture into Cisco IOS XE platforms. From Cisco IOS XE 17.13.1a, SELinux is enabled by default in Enforcing mode for Cisco IOS XE platforms. |
|
|
This feature ensures that the strength of the IKE (IKEv1 and IKEv2) SA encryption cipher is greater than or equal to the strength of its child IPsec SA encryption cipher. To enable this feature, use the crypto ipsec ike sa-strength-enforcement command. |
|
|
CUBE Features |
|
|
From Cisco IOS XE 17.13.1a onwards, using RTP keepalive packets, CUBE supports media transmission in the NAT environment. |
|
ROMMON Compatibility Matrix
The following table lists the ROMMON releases supported in Cisco IOS XE 17.13.x releases.
|
Platforms |
Cisco IOS XE Release |
Minimum ROMMON Release Supported for IOS XE |
Recommended ROMMON Release Supported for IOS XE |
|---|---|---|---|
|
Catalyst 8300 Series Edge Platforms |
|||
|
C8300-1N1S-4T2X|6T |
17.13.1a |
17.3(1r) |
17.6(6r) |
|
C8300-2N2S-4T2X|6T |
17.13.1a |
17.3(1.2r) |
17.6(6.1r) |
|
Catalyst 8200 Series Edge Platforms |
|||
|
C8200-1N-4T |
17.13.1a |
17.4(1r) |
17.6(6r) |
|
C8200L-1N-4T |
17.13.1a |
17.5(1.1r) |
17.6(6r) |
Resolved and Open Bugs for Cisco IOS XE 17.13.x
Resolved Bugs in Cisco IOS XE 17.13.1a
|
Identifier |
Headline |
|---|---|
|
Add verbose log to indicate grant ra-auto un configures grant auto in PKI server. |
|
|
QoS with more than four remark with set-cos does not work. |
|
|
NAT64 prefix is not originated into OMP. |
|
|
IOS XE router may experience unexpected reset while executing show utd engine standard statistics command |
|
|
Crash observed exporting PKCS12 to terminal via SSH CLI. |
|
|
Static route keep advertising via OMP even though there is no route. |
|
|
OMP to BGP redistribution leads to incorrect AS_Path installation on selected Next-hop. |
Open Bugs in Cisco IOS XE 17.13.1a
|
Identifier |
Headline |
|---|---|
|
Device segmentation fault crash with Network Mobility Services Protocol (NMSP). |
|
|
Creation of CLI to push at#enadis=0, followed by at#reboot to FN980, is required when configuring Multi-PDN. |
|
|
Device crash after changing NAT HSL configuration. |
|
|
SNMP unable to poll Cisco SD-WAN tunnel data after a minute. |
|
|
Device failing to upgrade due to CDB issue. |
|
|
Device may crash due to crypto IKMP process. |
|
|
Tracker for TLOC extension is down even though TLOC is up and there is ICMP reachability. |
|
|
Failed to connect to device : x.x.x.x Port: 830 user : Cisco SD-WAN-admin error : Connection failed. |
|
|
Device FTM crash with SIG enabled. |
|
|
SNMP bulkget cannot get loss, latency and jitter for ProbeClassTable and ClassIntervalTable OIDs. |
|
|
Endpoint tracker triggers a CPU hog. |
|
|
Device crashed generating multiple system reports. |
|
|
Error thrown when switching from SSE to SIG |
|
|
SNMP bulkget breaks the OID "appRouteStatisticsTable" after minute Not returning the correct order. |
|
|
Device lost security parameter after upgrade. |
|
|
PKI related crash after failing a CRL Fetch |
|
|
IP SLA probe for End-point-tracker doesnt work once endpoint tracker is changed until reload. |
|
|
Unexpected reboots on device due to QFP exception. |
|
|
Unexpected NAT translation occurs in a specific network. |
|
|
IOS XE:Traffic not encrypted and droped over IPSec SVTI tunnel. |
|
|
Device dropping IPSEC traffic when SVI is used as source for DMVPN tunnel. |
|
|
When RADIUS down, and there is an IKE-AUTH request received, the box stops replying to DPD packets. |
|
|
SSE tunnels don't come up with Dialer interface. Relax check in IKE. |
|
|
Device is unable to process hidden characters in a file while trying to use bootstrap method. |
|
|
IP SLA does not have checks for ICMP probes to be sent on source interface. |
|
|
UTD deployment failing if deployed from remote server hostname rather than ip. |
|
|
CSCwi35177 |
Router crash caused by continuous interface flap, interface associated to many IPsec interfaces. |
|
CSCwi30529 |
AAA:Template push fail when AAA authorization is set to local. |
Related Documentation
Communications, Services, and Additional Information
-
To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.
-
To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.
-
To submit a service request, visit Cisco Support.
-
To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco Marketplace.
-
To obtain general networking, training, and certification titles, visit Cisco Press.
-
To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a gateway to the Cisco bug-tracking system, which maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. The BST provides you with detailed defect information about your products and software.
Documentation Feedback
To provide feedback about Cisco technical documentation, use the feedback form available in the right pane of every online document.
Troubleshooting
For the most up-to-date, detailed troubleshooting information, see the Cisco TAC website at https://www.cisco.com/en/US/support/index.html.
Go to Products by Category and choose your product from the list, or enter the name of your product. Look under Troubleshoot and Alerts to find information for the issue that you are experiencing.
Feedback