Contents
Access List Commands
This chapter describes the Cisco IOS XR software commands used to configure IP Version 4 (IPv4) and IP Version 6 (IPv6) access lists on Cisco ASR 9000 Series Aggregation Services Routers .
An access control list (ACL) consists of one or more access control entries (ACEs) that collectively define the network traffic profile. This profile can then be referenced by Cisco IOS XR Software software features such as traffic filtering, priority or custom queueing, and dynamic access control. Each ACL includes an action element (permit or deny) and a filter element based on criteria such as source address, destination address, protocol, and protocol-specific parameters.
For detailed information about ACL concepts, configuration tasks, and examples, see the Cisco ASR 9000 Series Aggregation Services Router IP Addresses and Services Configuration Guide.
- clear access-list ipv4
- clear access-list ipv6
- copy access-list ipv4
- copy access-list ipv6
- deny (IPv4)
- deny (IPv6)
- ipv4 access-group
- ipv4 access-list
- ipv4 access-list log-update rate
- ipv4 access-list log-update threshold
- ipv6 access-group
- ipv6 access-list
- ipv6 access-list log-update rate
- ipv6 access-list log-update threshold
- ipv6 access-list maximum ace threshold
- ipv6 access-list maximum acl threshold
- permit (IPv4)
- permit (IPv6)
- remark (IPv4)
- remark (IPv6)
- resequence access-list ipv4
- resequence access-list ipv6
- show access-lists afi-all
- show access-lists ipv4
- show access-lists ipv6
clear access-list ipv4
clear access-list ipv4 access-list name [ sequence-number | hardware { ingress | egress}] [interface type interface-path-id] [ location node-id | sequence number ]
Syntax Description
access-list-name
Name of a particular IPv4 access list. The name cannot contain a spaces or quotation marks, but can include numbers.
sequence-number
(Optional) Specific sequence number with which counters are cleared for an access list. Range is 1 to 2147483644 .
hardware
Identifies the access list as an access group for an interface.
ingress
Specifies an inbound direction.
egress
Specifies an outbound direction.
interface
(Optional) Clears the interface statistics.
type
Interface type. For more information, use the question mark (?) online help function.
interface-path-id
Physical interface or virtual interface.
Note Use the show interfaces command to see a list of all interfaces currently configured on the router.
For more information about the syntax for the router, use the question mark (?) online help function.
location node-id
(Optional) Clears hardware resource counters from the designated node. The node-id argument is entered in the rack/slot/module notation.
sequence number
(Optional) Clears counters for an access list with a specific sequence number. Range is 1 to 2147483644 .
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the clear access-list ipv4 command to clear counters for a specified configured access list. Use a sequence number to clear counters for an access list with a specific sequence number.
Use the hardware keyword to clear counters for an access list that was enabled using the ipv4 access-group command.
Use an asterisk ( *) in place of the access-list-name argument to clear all access lists.
Note
An access list can be shared among multiple interfaces. Clearing hardware counters clears all counters for all interfaces that use the specified access list in a given direction (ingress or egress).
Task ID
Examples
In the following example, counters for an access list named marketing are cleared:
RP/0/RSP0/CPU0:router# show access-lists ipv4 marketing ipv4 access-list marketing 10 permit ip 192.168.34.0 0.0.0.255 any (51 matches) 20 permit ip 172.16.0.0 0.0.255.255 any (26 matches) 30 deny tcp host 172.16.0.0 eq bgp host 192.168.202.203 30 (5 matches) RP/0/RSP0/CPU0:router# clear access-list ipv4 marketing RP/0/RSP0/CPU0:router# show access-lists ipv4 marketing ipv4 access-list marketing 10 permit ip 192.168.34.0 0.0.0.255 any 20 permit ip 172.16.0.0 0.0.255.255 any 30 deny tcp host 172.16.0.0 eq bgp host 192.168.202.203 30In the following example, counters for an access list named acl_hw_1 in the outbound direction are cleared:
RP/0/RSP0/CPU0:router# show access-lists ipv4 acl_hw_1 hardware egress location 0/2/cp0 ipv4 access-list acl_hw_1 10 permit icmp 192.168.36.0 0.0.0.255 any (251 hw matches) 20 permit ip 172.16.3.0 0.0.255.255 any (29 hw matches) 30 deny tcp any any (58 hw matches) RP/0/RSP0/CPU0:router# clear access-list ipv4 acl_hw_1 hardware egress location 0/2/cp0 RP/0/RSP0/CPU0:router# show access-lists ipv4 acl_hw_1 hardware egress location 0/2/cp0 ipv4 access-list acl_hw_1 10 permit icmp 192.168.36.0 0.0.0.255 any 20 permit ip 172.16.3.0 0.0.255.255 any 30 deny tcp any anyclear access-list ipv6
clear access-list ipv6 access-list-name [ sequence-number | hardware { ingress | egress } ] [ interface type interface-path-id ] [ location node-id | sequence number ]
Syntax Description
access-list-name
Name of a particular IPv6 access list. The name cannot contain a spaces or quotation marks, but can include numbers.
sequence-number
(Optional) Specific sequence number for a particular access control entry (ACE) with which counters are cleared for an access list. Range is 1 to 2147483644.
hardware
(Optional) Identifies the access list as an access group for an interface.
ingress
(Optional) Specifies an inbound direction.
egress
(Optional) Specifies an outbound direction.
interface
(Optional) Clears the interface statistics.
type
(Optional) Interface type. For more information, use the question mark (?) online help function.
instance
interface-path-id
Physical interface or virtual interface.
Note Use the show interfaces command to see a list of all interfaces currently configured on the router.
For more information about the syntax for the router, use the question mark (?) online help function.
location node-id
(Optional) Clears counters for an access list enabled on a card interface. The node-id argument is entered in the rack/slot/module notation.
sequence number
(Optional) Specifies a specific sequence number that clears access list counters. Range is 1 to 2147483644.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The clear access-list ipv6 command is similar to the clear access-list ipv4 command, except that it is IPv6-specific.
Use the clear access-list ipv6 command to clear counters for a specified configured access list. Use a sequence number to clear counters for an access list with a specific sequence number
Use thehardware keyword to clear counters for an access list that was enabled using the ipv6 access-group command.
Use an asterisk (*) in place of the access-list-name argument to clear all access lists.
Note
An access list can be shared among multiple interfaces. Clearing hardware counters clears all counters for all interfaces that use the specified access list in a given direction (ingress or egress).
Task ID
Examples
In the following example, counters for an access list named marketing are cleared:
RP/0/RSP0/CPU0:router# show access-lists ipv6 marketing ipv6 access-list marketing 10 permit ipv6 3333:1:2:3::/64 any (51 matches) 20 permit ipv6 4444:1:2:3::/64 any (26 matches) 30 permit ipv6 5555:1:2:3::/64 any (5 matches) RP/0/RSP0/CPU0:router# clear access-list ipv6 marketing RP/0/RSP0/CPU0:router# show access-lists ipv6 marketing ipv6 access-list marketing 10 permit ipv6 3333:1:2:3::/64 any 20 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 anyIn the following example, counters for an access list named acl_hw_1 in the outbound direction are cleared:
RP/0/RSP0/CPU0:router# show access-lists ipv6 acl_hw_1 hardware egress location 0/2/cp0 ipv6 access-list acl_hw_1 10 permit ipv6 3333:1:2:3::/64 any (251 hw matches) 20 permit ipv6 4444:1:2:3::/64 any (29 hw matches) 30 deny tcp any any (58 hw matches) RP/0/RSP0/CPU0:router# clear access-list ipv6 acl_hw_1 hardware egress location 0/2/cp0 RP/0/RSP0/CPU0:router# show access-lists ipv6 acl_hw_1 hardware egress location 0/2/cp0 ipv6 access-list acl_hw_1 10 permit ipv6 3333:1:2:3::/64 any 20 permit ipv6 4444:1:2:3::/64 any 30 deny tcp any anycopy access-list ipv4
To create a copy of an existing IPv4 access list, use the copy access-list ipv4 command in EXEC mode.
Syntax Description
source-acl
Name of the access list to be copied.
destination-acl
Name of the destination access list where the contents of the source-acl argument is copied.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the copy access-list ipv4 command to copy a configured access list. Use the source-acl argument to specify the access list to be copied and the destination-acl argument to specify where to copy the contents of the source access list. The destination-acl argument must be a unique name; if the destination-acl argument name exists for an access list or prefix list, the access list is not copied. The copy access-list ipv4 command checks that the source access list exists then checks the existing list names to prevent overwriting existing access lists or prefix lists.
Task ID
Examples
In the following example, a copy of access list list-1 is created:
RP/0/RSP0/CPU0:router# show access-lists ipv4 list-1 ipv4 access-list list-1 10 permit tcp any any log 20 permit ip any any RP/0/RSP0/CPU0:router# copy access-list ipv4 list-1 list-2 RP/0/RSP0/CPU0:router# show access-lists ipv4 list-2 ipv4 access-list list-2 10 permit tcp any any log 20 permit ip any anyIn the following example, copying the access list list-1 to list-3 is denied because a list-3 access list already exists:
RP/0/RSP0/CPU0:router# copy access-list ipv4 list-1 list-3 list-3 exists in access-list RP/0/RSP0/CPU0:router# show access-lists ipv4 list-3 ipv4 access-list list-3 10 permit ip any any 20 deny tcp any any logcopy access-list ipv6
To create a copy of an existing IPv6 access list, use the copy access-list ipv6 command in EXEC mode.
Syntax Description
source-acl
Name of the access list to be copied.
destination-acl
Destination access list where the contents of the source-acl argument is copied.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the copy access-list ipv6 command to copy a configured access list. Use the source-acl argument to specify the access list to be copied and the destination-acl argument to specify where to copy the contents of the source access list. The destination-acl argument must be a unique name; if the destination-acl argument name exists for an access list or prefix list, the access list is not copied. The copy access-list ipv6 command checks that the source access list exists then checks the existing list names to prevent overwriting existing access lists or prefix lists.
Task ID
Examples
In the following example, a copy of access list list-1 is created:
RP/0/RSP0/CPU0:router# show access-lists ipv6 list-1 ipv6 access-list list-1 10 permit tcp any any log 20 permit ipv6 any any RP/0/RSP0/CPU0:router# copy access-list ipv6 list-1 list-2 RP/0/RSP0/CPU0:router# show access-lists ipv6 list-2 ipv6 access-list list-2 10 permit tcp any any log 20 permit ipv6 any anyIn the following example, copying access list list-1 to list-3 is denied because a list-3 access list already exists:
RP/0/RSP0/CPU0:router# copy access-list ipv6 list-1 list-3 list-3 exists in access-list RP/0/RSP0/CPU0:router# show access-lists ipv6 list-3 ipv6 access-list list-3 10 permit ipv6 any any 20 deny tcp any any logdeny (IPv4)
To set conditions for an IPv4 access list, use the deny command in access list configuration mode. There are two versions of the deny command: deny (source), and deny (protocol). To remove a condition from an access list, use the no form of this command.
[sequence-number] deny source [source-wildcard] [ log | log-input ]
[sequence-number]denyprotocol source source-wildcard destination destination-wildcard[ precedenceprecedence] [ dscpdscp] [ fragments] [ packet-length operator packet-length value] [ log | log-input] [ ttl ttl value [value1....value2]]
no sequence-number
Internet Control Message Protocol (ICMP)
[sequence-number] deny icmp source source-wildcard destination destination-wildcard [icmp-type] [icmp-code] [ precedence precedence ] [ dscp dscp ] [fragments] [ log | log-input ] [icmp-off]
Internet Group Management Protocol (IGMP)
[sequence-number] deny igmp source source-wildcard destination destination-wildcard [igmp-type] [ precedence precedence ] [ dscp value ] [fragments] [ log | log-input ]
User Datagram Protocol (UDP)
[sequence-number] deny udp source source-wildcard [ operator { port | protocol-port } ] destination destination-wildcard [ operator { port | protocol-port } ] [ precedence precedence ] [ dscp dscp ] [fragments] [ log | log-input ]
Syntax Description
Command Default
There is no specific condition under which a packet is denied passing the IPv4 access list.
ICMP message generation is enabled by default.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the deny command following the ipv4 access-list command to specify conditions under which a packet cannot pass the access list.
By default, the first statement in an access list is number 10, and the subsequent statements are incremented by 10.
You can add permit, deny, or remark statements to an existing access list without retyping the entire list. To add a new statement anywhere other than at the end of the list, create a new statement with an appropriate entry number that falls between two existing entry numbers to indicate where it belongs.
If you want to add a statement between two consecutively numbered statements (for example, between lines 10 and 11), first use the resequence access-list command to renumber the first statement and increment the entry number of each subsequent statement. The increment argument causes new, unused line numbers between statements. Then add a new statement with the entry-number argument, specifying where it belongs in the access list.
The following is a list of precedence names:
The following is a list of ICMP message type names:
- administratively-prohibited
- alternate-address
- conversion-error
- dod-host-prohibited
- dod-net-prohibited
- echo
- echo-reply
- general-parameter-problem
- host-isolated
- host-precedence-unreachable
- host-redirect
- host-tos-redirect
- host-tos-unreachable
- host-unknown
- host-unreachable
- information-reply
- information-request
- mask-reply
- mask-request
- mobile-redirect
- net-redirect
- net-tos-redirect
- net-tos-unreachable
- net-unreachable
- network-unknown
- no-room-for-option
- option-missing
- packet-too-big
- parameter-problem
- port-unreachable
- precedence-unreachable
- protocol-unreachable
- reassembly-timeout
- redirect
- router-advertisement
- router-solicitation
- source-quench
- source-route-failed
- time-exceeded
- timestamp-reply
- timestamp-request
- traceroute
- ttl-exceeded
- unreachable
The following is a list of TCP port names that can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. You can find port numbers corresponding to these protocols by typing a ? in the place of a port number.
- bgp
- chargen
- cmd
- daytime
- discard
- domain
- echo
- exec
- finger
- ftp
- ftp-data
- gopher
- hostname
- ident
- irc
- klogin
- kshell
- login
- lpd
- nntp
- pim-auto-rp
- pop2
- pop3
- smtp
- sunrpc
- tacacs
- talk
- telnet
- time
- uucp
- whois
- www
The following UDP port names can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. You can find port numbers corresponding to these protocols by typing a ? in the place of a port number.
- biff
- bootpc
- bootps
- discard
- dnsix
- domain
- echo
- isakmp
- mobile-ip
- nameserver
- netbios-dgm
- netbios-ns
- netbios-ss
- ntp
- pim-auto-rp
- rip
- snmp
- snmptrap
- sunrpc
- syslog
- tacacs
- talk
- tftp
- time
- who
- xdmcp
Use the following flags in conjunction with the match-any and match-all keywords and the + and - signs to select the flags to display:
For example, match-all + ack + syn displays TCP packets with both the ack and syn flags set, or match-any + ack - syn displays the TCP packets with the ack set or the syn not set.
Task ID
Examples
The following example shows how to set a deny condition for an access list named Internetfilter:
RP/0/RSP0/CPU0:router(config)# ipv4 access-list Internetfilter RP/0/RSP0/CPU0:router(config-ipv4-acl)# 10 deny 192.168.34.0 0.0.0.255 RP/0/RSP0/CPU0:router(config-ipv4-acl)# 20 deny 172.16.0.0 0.0.255.255 RP/0/RSP0/CPU0:router(config-ipv4-acl)# 25 deny tcp host 172.16.0.0 eq bgp host 192.168.202.203 range 1300 1400 RP/0/RSP0/CPU0:router(config-ipv4-acl)# permit 10.0.0.0 0.255.255.255Related Commands
Command
Description
Filters incoming or outgoing IPv4 traffic on an interface.
Defines an IPv4 access list and enters IPv4 access list configuration mode.
Sets the permit conditions for an IPv4 access list.
Inserts a helpful remark about an IPv4 access list entry.
Changes the starting entry number of the first statement in an existing IPv4 access list, and the number by which subsequent statements are incremented.
Displays the contents of all current IPv4 access lists.
deny (IPv6)
To set deny conditions for an IPv6 access list, use the deny command in IPv6 access list configuration mode. To remove the deny conditions, use the no form of this command.
[sequence-number] denyprotocol { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } [ operator { port | protocol-port } ] [ dscpvalue] [ routing] [ authen] [ destopts] [ fragments] [ packet-length operator packet-length value ] [ log | log-input] [ ttl operator ttl value ]
no sequence-number
Internet Control Message Protocol (ICMP)
[ sequence-number]deny icmp { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } { destination-ipv6-prefix/ prefix-length | any | host destination-ipv6-address } [ icmp-type] [ icmp-code][ dscp value] [ routing] [ authen] [ destopts] [ fragments] [ log] [ log-input] [ icmp-off]
Transmission Control Protocol (TCP)
[sequence-number]deny tcp { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } [ operator { port | protocol-port } ] { destination-ipv6-prefix/ prefix-length | any | host destination-ipv6-address } [ operator { port | protocol | port } ] [ dscpvalue] [ routing] [ authen] [ destopts] [ fragments] [ established] { match-any | match-all | + | - } [ flag-name] [ log] [ log-input]
User Datagram Protocol (UDP)
[sequence-number]deny tcp { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } [ operator { port | protocol-port } ] { destination-ipv6-prefix/ prefix-length | any | host destination-ipv6-address } [ operator { port | protocol | port } ] [ dscpvalue] [ routing] [ authen] [ destopts] [ fragments] [ established] [ flag-name] [ log] [ log-input]
Syntax Description
sequence-number
(Optional) Number of the deny statement in the access list. This number determines the order of the statements in the access list. Range is 1 to 2147483644. (By default, the first statement is number 10, and the subsequent statements are incremented by 10.) Use the resequence access-list command to change the number of the first statement and increment subsequent statements of a configured access list.
protocol
Name or number of an Internet protocol. It can be one of the keywords ahp , eigrp, esp , gre, icmp , igmp, igrp, ipinip, ipv6 , nos, ospf, pcp , tcp , or udp , or an integer in the range from 0 to 255 representing an IPv6 protocol number.
source-ipv6-prefix / prefix-length
The source IPv6 network or class of networks about which to set deny conditions.
This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
any
An abbreviation for the IPv6 prefix ::/0.
host source-ipv6-address
Source IPv6 host address about which to set deny conditions.
This source-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
operator {port | protocol-port}
(Optional) Operand that compares the source or destination ports of the specified protocol. Operands are lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).
If the operator is positioned after the source-ipv6-prefix / prefix-length argument, it must match the source port.
If the operator is positioned after the destination-ipv6-prefix / prefix-length argument, it must match the destination port.
The range operator requires two port numbers. All other operators require one port number.
The port argument is the decimal number of a TCP or UDP port. Range is 0 to 65535. The protocol-port argument is the name of a TCP or UDP port. TCP port names can be used only when filtering TCP. UDP port names can be used only when filtering UDP.
destination-ipv6-prefix / prefix-length
Destination IPv6 network or class of networks about which to set deny conditions.
This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
host destination-ipv6-address
Destination IPv6 host address about which to set deny conditions.
This destination-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
dscp value
(Optional) Matches a differentiated services code point DSCP value against the traffic class value in the Traffic Class field of each IPv6 packet header. Range is 0 to 63.
routing
(Optional) Matches source-routed packets against the routing extension header within each IPv6 packet header.
authen
(Optional) Matches if the IPv6 authentication header is present.
destopts
(Optional) Matches if the IPv6 destination options header is present.
fragments
(Optional) Matches noninitial fragmented packets where the fragment extension header contains a nonzero fragment offset. The fragments keyword is an option only if the operator [ port-number ] arguments are not specified.
log
(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by the logging console command.)
The message includes the access list name and sequence number, whether the packet was denied; the protocol, whether it was TCP, UDP, ICMP, or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. The message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets denied in the prior 5-minute interval.
log-input
(Optional) Provides the same function as the log keyword, except that the logging message also includes the input interface.
ttl
(Optional) Turns on matching against time-to-life (TTL) value.
operator
(Optional) Operand that compares the source or destination ports of the specified protocol. Operands are lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).
ttl value [value1 ... value2]
(Optional) TTL value used for filtering. Range is 1 to 255.
If only value is specified, the match is against this value.
If both value1 and value2 are specified, the packet TTL is matched against the range of TTLs between value1 and value2 .
icmp-off
(Optional) Turns off ICMP generation for denied packets
icmp-type
(Optional) ICMP message type for filtering ICMP packets. ICMP packets can be filtered by ICMP message type. Range is 0 to 255.
icmp-code
(Optional) ICMP message code for filtering ICMP packets. ICMP packets that are filtered by ICMP message type can also be filtered by the ICMP message code. Range is 0 to 255.
established
(Optional) For the TCP protocol only: Indicates an established connection.
match-any
(Optional) For the TCP protocol only: Filters on any combination of TCP flags.
match-all
(Optional) For the TCP protocol only: Filters on all TCP flags.
+ | -
(Required) For the TCP protocol match-any , match-all : Prefix flag-name with + or - . Use the + flag-name argument to match packets with the TCP flag set. Use the - flag-name argument to match packets when the TCP flag is not set.
flag-name
(Optional) For the TCP protocol match-any , match-all . Flag names are: ack, fin, psh, rst, syn.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The deny (IPv6) command is similar to the deny (IPv4) command, except that it is IPv6-specific.
Use the deny (IPv6) command following the ipv6 access-list command to define the conditions under which a packet passes the access list.
Specifying ipv6 for the protocol argument matches against the IPv6 header of the packet.
By default, the first statement in an access list is number 10, and the subsequent statements are numbered in increments of 10.
You can add permit, deny, or remark statements to an existing access list without retyping the entire list. To add a new statement anywhere other than at the end of the list, create a new statement with an appropriate entry number that falls between two existing entry numbers to indicate where it belongs.
Both the source-ipv6-prefix/prefix-length and destination-ipv6-prefix/prefix-length arguments are used for traffic filtering (the source prefix filters traffic based upon the traffic source; the destination prefix filters traffic based upon the traffic destination).
Note
IPv6 prefix lists, not access lists, should be used for filtering routing protocol prefixes.
The fragments keyword is an option only if the operator [port | protocol-port ] arguments are not specified.
Task ID
Examples
The following example shows how to configure the IPv6 access list named toCISCO and applies the access list to outbound traffic on GigabitEthernet interface 0/2/0/2. Specifically, the first deny entry in the list keeps all packets that have a destination TCP port number greater than 5000 from exiting out of GigabitEthernet interface 0/2/0/2. The second deny entry in the list keeps all packets that have a source UDPo port number less than 5000 from exiting out of GigabitEthernet interface 0/2/0/2. The second deny entry also logs all matches to the console. The first permit entry in the list permits all ICMP packets to exit out of GigabitEthernet interface 0/2/0/2. The second permit entry in the list permits all other traffic to exit out of GigabitEthernet interface 0/2/0/2. The second permit entry is necessary because an implicit deny all condition is at the end of each IPv6 access list.
RP/0/RSP0/CPU0:router(config)# ipv6 access-list toCISCO RP/0/RSP0/CPU0:router(config-ipv6-acl)# deny tcp any any gt 5000 RP/0/RSP0/CPU0:router(config-ipv6-acl)# deny ipv6 any lt 5000 any log RP/0/RSP0/CPU0:router(config-ipv6-acl)# permit icmp any any RP/0/RSP0/CPU0:router(config-ipv6-acl)# permit any any RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv6 access-group tOCISCO outRelated Commands
Command
Description
Defines an IPv6 access list and enters IPv6 access list configuration mode.
Sets permit conditions for an IPv6 access list.
Inserts a helpful remark about an IPv6 access list entry.
Changes the starting entry number of the first statement in an existing IPv6 access list, and the number by which subsequent statements are incremented.
ipv4 access-group
To control access to an interface, use the ipv4 access-group command in interface configuration mode. To remove the specified access group, use the no form of this command.
ipv4 access-group access-list-name { ingress | egress } [hardware-count] [interface-statistics]
no ipv4 access-group access-list-name { ingress | egress } [hardware-count] [interface-statistics]
Syntax Description
access-list-name
Name of an IPv4 access list as specified by an ipv4 access-list command.
ingress
Filters on inbound packets.
egress
Filters on outbound packets.
hardware-count
(Optional) Specifies to access a group’s hardware counters.
interface-statistics
(Optional) Specifies per-interface statistics in the hardware.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the ipv4 access-group command to control access to an interface. To remove the specified access group, use the no form of the command. Use the access-list-name argument to specify a particular IPv4 access list. Use theingress keyword to filter on inbound packets or theegress keyword to filter on outbound packets. Use the hardware-count argument to enable hardware counters for the access group.
Permitted packets are counted only when hardware counters are enabled using the hardware-count argument. Denied packets are counted whether hardware counters are enabled or not.
Note
For packet filtering applications using the ipv4 access-group command, packet counters are maintained in hardware for each direction. If an access group is used on multiple interfaces in the same direction, then packets are counted for each interface that has the hardware-count argument enabled.
If the access list permits the addresses, the software continues to process the packet. If the access list denies the address, the software discards the packet and returns an Internet Control Message Protocol (ICMP) host unreachable message.
If the specified access list does not exist, all packets are passed.
By default, the unique or per-interface ACL statistics are disabled.
Task ID
Examples
The following example shows how to apply filters on packets inbound and outbound from GigabitEthernet Packet-over-SONET (POS) interface 0/2/0/2:
RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv4 access-group p-ingress-filter ingress RP/0/RSP0/CPU0:router(config-if)# ipv4 access-group p-egress-filter egressThe following example shows how to apply per-interface statistics in the hardware:
RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv4 access-group p-ingress-filter ingress interface-statisticsRelated Commands
Command
Description
Resets the IPv4 access list match counters.
Sets the deny conditions for an IPv4 access list.
Defines an IPv4 access list and enters IPv4 access list configuration mode.
Sets the permit conditions for an IPv4 access list.
Displays the contents of all current IPv4 access lists.
show ipv4 interface
Displays the usability status of interfaces configured for IPv4.
ipv4 access-list
To define an IPv4 access list by name, use the ipv4 access-list command in global configuration mode. To remove all entries in an IPv4 access list, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the ipv4 access-list command to configure an IPv4 access list. This command places the router in access list configuration mode, in which the denied or permitted access conditions must be defined with the deny or permit command.
Use the resequence access-list ipv4 command if you want to add a permit, deny, or remark statement between consecutive entries in an existing IPv4 access list. Specify the first entry number (the base) and the increment by which to separate the entry numbers of the statements. The software renumbers the existing statements, thereby making room to add new statements with the unused entry numbers.
Use the ipv4 access-group command to apply the access list to an interface.
Task ID
Examples
The following example shows how to define a standard access list named Internetfilter:
RP/0/RSP0/CPU0:router(config)# ipv4 access-list Internetfilter RP/0/RSP0/CPU0:router(config-if)# 10 permit 192.168.34.0 0.0.0.255 RP/0/RSP0/CPU0:router(config-if)# 20 permit 172.16.0.0 0.0.255.255 RP/0/RSP0/CPU0:router(config-if)# 30 permit 10.0.0.0 0.255.255.255 RP/0/RSP0/CPU0:router(config-if)# 39 remark Block BGP traffic from 172.16 net. RP/0/RSP0/CPU0:router(config-if)# 40 deny tcp host 172.16.0.0 eq bgp host 192.168.202.203 range 1300 1400Related Commands
Command
Description
Resets the IPv4 access list match counters.
Sets the deny conditions for a named IPv4 access list.
Filters incoming or outgoing IPv4 traffic on an interface.
Sets the permit conditions for a named IPv4 access list.
Inserts a helpful remark about an IPv4 access list entry.
Changes the starting entry number of the first statement in an existing IPv4 access list, and the number by which subsequent statements are incremented.
Displays the contents of all current IPv4 access lists.
ipv4 access-list log-update rate
To specify the rate at which IPv4 access lists are logged, use the ipv4 access-list log-update rate command in global configuration mode. To return the update rate to the default setting, use the no form of this command.
Syntax Description
rate-number
Rate at which IPv4 access hit logs are generated per second on the router. Range is 1 to 1000.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The rate-number argument applies to all the IPv4 access-lists configured on the interfaces. That is, at any given time there can be between 1 and 1000 log entries for the system.
Task ID
ipv4 access-list log-update threshold
To specify the number of updates that are logged for IPv4 access lists, use the ipv4 access-list log-update threshold command in global configuration mode. To return the number of logged updates to the default setting, use the no form of this command.
ipv4 access-list log-update threshold update-number
no ipv4 access-list log-update threshold update-number
Syntax Description
update-number
Number of updates that are logged for every IPv4 access list configured on the router. Range is 0 to 2147483647.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
IPv4 access list updates are logged at 5-minute intervals, following the first logged update. Configuring a lower number of updates (a number lower than the default) is useful when more frequent update logging is desired.
Task ID
Examples
The following example shows how to configure a log threshold of ten updates for every IPv4 access list configured on the router:
RP/0/RSP0/CPU0:router(config)# ipv4 access-list log-update threshold 10ipv6 access-group
To control access to an interface, use the ipv6 access-group command in interface configuration mode. To remove the specified access group, use the no form of this command.
ipv6 access-group access-list-name { ingress | egress } [interface-statistics]
no ipv6 access-group access-list-name { ingress | egress } [interface-statistics]
Syntax Description
access-list-name
Name of an IPv6 access list as specified by an ipv6 access-list command.
ingress
Filters on inbound packets.
egress
Filters on outbound packets.
interface-statistics
(Optional) Specifies per-interface statistics in the hardware.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The ipv6 access-group command is similar to the ipv4 access-group command, except that it is IPv6-specific.
Use the ipv6 access-group command to control access to an interface. To remove the specified access group, use the no form of the command. Use the access-list-name to specify a particular IPv6 access list. Use theingress keyword to filter on inbound packets or the egress keyword to filter on outbound packets.
Note
For packet filtering applications using the ipv6 access-group command, packet counters are maintained in hardware for each direction. If an access group is used on multiple interfaces in the same direction, then packets are counted for each interface.
If the access list permits the addresses, the software continues to process the packet. If the access list denies the address, the software discards the packet and returns a rate-limited Internet Control Message Protocol (ICMP) host unreachable message.
If the specified access list does not exist, all packets are passed.
By default, the unique or per-interface ACL statistics are disabled.
Task ID
Examples
The following example shows how to apply filters on packets inbound and outbound from GigabitEthernet interface 0/2/0/2:
RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv6 access-group p-in-filter ingress RP/0/RSP0/CPU0:router(config-if)# ipv6 access-group p-out-filter egressThe following example shows how to apply per-interface statistics in the hardware:
RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv6 access-group p-in-filter ingress interface-statisticsRelated Commands
Command
Description
Copies an existing IPv6 access list.
Sets the deny conditions for an IPv6 access list.
Defines an IPv6 access list and enters IPv6 access list configuration mode.
Sets conditions under which a packet passes a named IPv6 access list.
show ipv6 interface
Displays the usability status of interfaces configured for IPv6.
ipv6 access-list
To define an IPv6 access list and to place the router in IPv6 access list configuration mode, use the ipv6 access-list command in global configuration mode. To remove the access list, use the no form of this command.
Syntax Description
name
Name of the IPv6 access list. Names cannot contain a space or quotation mark, or begin with a numeric.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The ipv6 access-list command is similar to the ipv4 access-list command, except that it is IPv6-specific.
The IPv6 access lists are used for traffic filtering based on source and destination addresses, IPv6 option headers, and optional, upper-layer protocol type information for finer granularity of control. IPv6 access lists are defined by using the ipv6 access-list command in global configuration mode and their permit and deny conditions are set by using the deny and permit commands in IPv6 access list configuration mode. Configuring the ipv6 access-list command places the router in IPv6 access list configuration mode—the router prompt changes to router (config-ipv6-acl)#. From IPv6 access list configuration mode, permit and deny conditions can be set for the defined IPv6 access list.
Refer to the deny (IPv6) and permit (IPv6) commands for more information on filtering IPv6 traffic based on IPv6 option headers and optional, upper-layer protocol type information. See the “Examples” section for an example of a translated IPv6 access control list (ACL) configuration.
Note
No more than one IPv6 access list can be applied to an interface per direction.
Note
Every IPv6 access list has an implicit deny ipv6 any any statement as its last match condition. An IPv6 access list must contain at least one entry for the implicit deny ipv6 any any statement to take effect.
Note
IPv6 prefix lists, not access lists, should be used for filtering routing protocol prefixes.
Use the ipv6 access-group interface configuration command with the access-list-name argument to apply an IPv6 access list to an IPv6 interface.
Note
An IPv6 access list applied to an interface with the ipv6 access-group command filters traffic that is forwarded, not originated, by the router.
Note
Every IPv6 ACL has implicit permit icmp any any nd-na, permit icmp any any nd-ns, and deny ipv6 any any statements as its last match conditions. (The former two match conditions allow for ICMPv6 neighbor discovery.) An IPv6 ACL must contain at least one entry for the implicit deny ipv6 any any statement to take effect.permit icmp any any nd-na permit icmp any any nd-ns deny ipv6 any any deny ipv6 any any
The IPv6 neighbor discovery process makes use of the IPv6 network layer service; therefore, by default, IPv6 ACLs implicitly allow IPv6 neighbor discovery packets to be sent and received on an interface. In IPv4, the Address Resolution Protocol (ARP), which is equivalent to the IPv6 neighbor discovery process, makes use of a separate data link layer protocol; therefore, by default, IPv4 ACLs implicitly allow ARP packets to be sent and received on an interface.
Task ID
Examples
The following example shows how to configure the IPv6 access list named list2 and applies the ACL to outbound traffic on interface GigabitEthernet 0/2/0/2. Specifically, the first ACL entry keeps all packets from the network fec0:0:0:2::/64 (packets that have the site-local prefix fec0:0:0:2 as the first 64 bits of their source IPv6 address) from exiting out of interface GigabitEthernet 0/2/0/2. The second entry in the ACL permits all other traffic to exit out of interface GigabitEthernet 0/2/0/2. The second entry is necessary because an implicit deny all condition is at the end of each IPv6 ACL.
RP/0/RSP0/CPU0:router(config)# ipv6 access-list list2 RP/0/RSP0/CPU0:router(config-ipv6-acl)# 10 deny fec0:0:0:2::/64 any RP/0/RSP0/CPU0:router(config-ipv6-acl)# 20 permit any any RP/0/RSP0/CPU0:router# show ipv6 access-lists list2 ipv6 access-list list2 10 deny ipv6 fec0:0:0:2::/64 any 20 permit ipv6 any any RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv6 access-group list2 out
Note
IPv6 is automatically configured as the protocol type in permit any any and deny any any statements that are translated from global configuration mode to IPv6 access list configuration mode.
Note
An IPv6 router does not forward to another network an IPv6 packet that has a link-local address as either its source or destination address (and the source interface for the packet is different from the destination interface for the packet).
ipv6 access-list log-update rate
To specify the rate at which IPv6 access lists are logged, use the ipv6 access-list log-update rate command in global configuration mode. To return the update rate to the default setting, use the no form of this command.
Syntax Description
rate-number
Rate at which IPv6 access hit logs are generated per second on the router. Range is 1 to 1000.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The rate-number argument applies to all the IPv6 access-lists configured on the interfaces. That is, at any given time there can be between 1 and 1000 log entries for the system.
Task ID
ipv6 access-list log-update threshold
To specify the number of updates that are logged for IPv6 access lists (ACLs), use the ipv6 access-list log-update threshold command in global configuration mode. To return the number of logged updates to the default setting, use the no form of this command.
ipv6 access-list log-update threshold update-number
no ipv6 access-list log-update threshold update-number
Syntax Description
update-number
Number of updates that are logged for every IPv6 access list configured on the router. Range is 0 to 2147483647.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The ipv6 access-list log-update threshold command is similar to the ipv4 access-list log-update threshold command, except that it is IPv6-specific.
IPv6 access list updates are logged at 5-minute intervals, following the first logged update. Configuring a lower number of updates (a number lower than the default) is useful when more frequent update logging is desired.
Task ID
ipv6 access-list maximum ace threshold
To set the maximum number of access control entries (ACEs) for IPv6 access lists, use the ipv6 access-list maximum ace threshold command in global configuration mode. To reset the ACE limit for IPv6 access lists, use the no form of this command.
ipv6 access-list maximum ace threshold ace-number
no ipv6 access-list maximum ace threshold ace-number
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the ipv6 access-list maximum ace threshold command to set the maximum number of configurable ACEs for IPv6 access lists. Out of resource (OOR) limits the number of ACEs that can be configured in the system. When the maximum number of configurable ACEs is reached, configuration of new ACEs is rejected.
Task ID
Examples
The following example shows how to set the maximum number of ACEs for IPv6 access lists to 75000:
RP/0/RSP0/CPU0:router(config)# ipv6 access-list maximum ace threshold 75000ipv6 access-list maximum acl threshold
To set the maximum number of configurable IPv6 access control lists (ACLs), use the ipv6 access-list maximum acl threshold command in global configuration mode. To reset the IPv6 ACL limit, use the no form of this command.
ipv6 access-list maximum acl threshold acl-number
no ipv6 access-list maximum ace threshold acl-number
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the ipv6 access-list maximum acl threshold command to set the maximum number of configurable IPv6 ACLs. Out of resource (OOR) limits the number of ACLs that can be configured in the system. When the limit is reached, configuration of new ACLs is rejected.
Task ID
Examples
The following example shows how to set the maximum number of configurable IPv6 ACLs to 1500:
RP/0/RSP0/CPU0:router(config)# ipv6 access-list maximum acl threshold 1500permit (IPv4)
To set conditions for an IPv4 access list, use the permit command in access list configuration mode. There are two versions of the permit command: permit (source), and permit (protocol). To remove a condition from an access list, use the no form of this command.
[sequence-number] permit source [source-wildcard] [ log | log-input ]
[sequence-number] permit protocol source source-wildcard destination destination-wildcard [capture] [ precedence precedence ] [ default nexthop [ipv4-address1] [ipv4-address2] [ipv4-address3] ] [ dscp dscp ] [fragments] [ log | log-input ] [ nexthop [ track track-name ] [ipv4-address1] [ipv4-address2] [ipv4-address3] ] [ ttl ttl value [ value1 . .. value2 ] ]
no sequence-number
Internet Control Message Protocol (ICMP)
[sequence-number] permit icmp source source-wildcard destination destination-wildcard [icmp-type] [icmp-code] [ precedence precedence ] [ dscp dscp ] [fragments] [ log | log-input ] [icmp-off]
Internet Group Management Protocol (IGMP)
[sequence-number] permit igmp source source-wildcard destination destination-wildcard [igmp-type] [ precedence precedence ] [ dscp value ] [fragments] [ log | log-input ]
User Datagram Protocol (UDP)
[sequence-number] permit udp source source-wildcard [ operator { port | protocol-port } ] destination destination-wildcard [ operator { port | protocol-port } ] [ precedence precedence ] [ dscp dscp ] [fragments] [ log | log-input ]
Syntax Description
Command Default
There is no specific condition under which a packet is denied passing the IPv4 access list.
ICMP message generation is enabled by default.
Command History
Release
Modification
Release 3.7.2
This command was introduced.
Release 4.0.1
The capture keyword was added.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the permit command following the ipv4 access-list command to specify conditions under which a packet can pass the access list.
By default, the first statement in an access list is number 10, and the subsequent statements are incremented by 10.
You can add permit, deny, or remark statements to an existing access list without retyping the entire list. To add a new statement anywhere other than at the end of the list, create a new statement with an appropriate entry number that falls between two existing entry numbers to indicate where it belongs.
If you want to add a statement between two consecutively numbered statements (for example, between lines 10 and 11), first use the resequence access-list command to renumber the first statement and increment the entry number of each subsequent statement. The increment argument causes new, unused line numbers between statements. Then add a new statement with the entry-number specifying where it belongs in the access list.
The following is a list of precedence names:
The following is a list of ICMP message type names:
- administratively-prohibited
- alternate-address
- conversion-error
- dod-host-prohibited
- dod-net-prohibited
- echo
- echo-reply
- general-parameter-problem
- host-isolated
- host-precedence-unreachable
- host-redirect
- host-tos-redirect
- host-tos-unreachable
- host-unknown
- host-unreachable
- information-reply
- information-request
- mask-reply
- mask-request
- mobile-redirect
- net-redirect
- net-tos-redirect
- net-tos-unreachable
- net-unreachable
- network-unknown
- no-room-for-option
- option-missing
- packet-too-big
- parameter-problem
- port-unreachable
- precedence-unreachable
- protocol-unreachable
- reassembly-timeout
- redirect
- router-advertisement
- router-solicitation
- source-quench
- source-route-failed
- time-exceeded
- timestamp-reply
- timestamp-request
- traceroute
- ttl-exceeded
- unreachable
The following is a list of TCP port names that can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. You can find port numbers corresponding to these protocols by typing a ? in the place of a port number.
- bgp
- chargen
- cmd
- daytime
- discard
- domain
- echo
- exec
- finger
- ftp
- ftp-data
- gopher
- hostname
- ident
- irc
- klogin
- kshell
- login
- lpd
- nntp
- pim-auto-rp
- pop2
- pop3
- smtp
- sunrpc
- tacacs
- talk
- telnet
- time
- uucp
- whois
- www
The following UDP port names can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. You can find port numbers corresponding to these protocols by typing a ? in the place of a port number.
- biff
- bootpc
- bootps
- discard
- dnsix
- domain
- echo
- isakmp
- mobile-ip
- nameserver
- netbios-dgm
- netbios-ns
- netbios-ss
- ntp
- pim-auto-rp
- rip
- snmp
- snmptrap
- sunrpc
- syslog
- tacacs
- talk
- tftp
- time
- who
- xdmcp
Use the following flags in conjunction with the match-any and match-all keywords and the + and - signs to select the flags to display:
For example, match-all +ack +syn displays TCP packets with both the ack and syn flags set, or match-any +ack – syn displays the TCP packets with the ack set or the syn not set.
Task ID
Examples
The following example shows how to set a permit condition for an access list named Internetfilter:
RP/0/RSP0/CPU0:router(config)# ipv4 access-list Internetfilter RP/0/RSP0/CPU0:router(config-ipv4-acl)# 10 permit 192.168.34.0 0.0.0.255 RP/0/RSP0/CPU0:router(config-ipv4-acl)# 20 permit 172.16.0.0 0.0.255.255 RP/0/RSP0/CPU0:router(config-ipv4-acl)# 25 permit tcp host 172.16.0.0 eq bgp host 192.168.202.203 range 1300 1400 RP/0/RSP0/CPU0:router(config-ipv4-acl)# deny 10.0.0.0 0.255.255.255Related Commands
Command
Description
Sets the conditions for an IPv4 access list.
Filters incoming or outgoing IPv4 traffic on an interface.
Defines an IPv4 access list and enters IPv4 access list configuration mode.
Inserts a helpful remark about an IPv4 access list entry.
Changes the starting entry number of the first statement in an existing IPv4 access list, and the number by which subsequent statements are incremented.
Displays the contents of all current IPv4 access lists.
permit (IPv6)
To set permit conditions for an IPv6 access list, use the permit command in IPv6 access list configuration mode. To remove the permit conditions, use the no form of this command.
[sequence-number] permitprotocol { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } [ operator { port | protocol-port } capture ] [ dscpvalue] [ routing] [ authen] [ destopts] [ fragments] [ packet-length operator packet-length value ] [ log | log-input] [ ttl operator ttl value ]
no sequence-number
Internet Control Message Protocol (ICMP)
[ sequence-number]permit icmp { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } { destination-ipv6-prefix/ prefix-length | any | host destination-ipv6-address } [ icmp-type] [ icmp-code][ dscp value] [ routing] [ authen] [ destopts] [ fragments] [ log] [ log-input] [ icmp-off]
Transmission Control Protocol (TCP)
[sequence-number]permit tcp { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } [ operator { port | protocol-port } ] { destination-ipv6-prefix/ prefix-length | any | host destination-ipv6-address } [ operator { port | protocol | port } ] [ dscpvalue] [ routing] [ authen] [ destopts] [ fragments] [ established] { match-any | match-all | + | - } [ flag-name] [ log] [ log-input]
User Datagram Protocol (UDP)
[sequence-number]permit tcp { source-ipv6-prefix/ prefix-length | any | host source-ipv6-address } [ operator { port | protocol-port } ] { destination-ipv6-prefix/ prefix-length | any | host destination-ipv6-address } [ operator { port | protocol | port } ] [ dscpvalue] [ routing] [ authen] [ destopts] [ fragments] [ established] [ flag-name] [ log] [ log-input]
Syntax Description
sequence-number
(Optional) Number of the permit statement in the access list. This number determines the order of the statements in the access list. Range is 1 to 2147483644. (By default, the first statement is number 10, and the subsequent statements are incremented by 10.) Use the resequence access-list command to change the number of the first statement and increment subsequent statements of a configured access list.
protocol
Name or number of an Internet protocol. It can be one of the keywords ahp , eigrp , esp , gre , icmp , igmp , igrp , isinip , ipv6 , nos , ospf , pcp , sctp , tcp , or udp , or an integer in the range from 0 to 255 representing an IPv6 protocol number.
source-ipv6-prefix / prefix-length
Source IPv6 network or class of networks about which to set permit conditions.
This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
any
An abbreviation for the IPv6 prefix ::/0.
capture
Captures matching traffic.
When the acl command is configured on the source mirroring port, if the ACL configuration command does not use the capture keyword, no traffic gets mirrored. If the ACL configuration uses the capture keyword, but the acl command is not configured on the source port, then the whole port traffic is mirrored and the capture action does not have any affect.
host source-ipv6-address
Source IPv6 host address about which to set permit conditions.
This source-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
operator {port | protocol-port}
(Optional) Operand that compares the source or destination ports of the specified protocol. Operands are lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).
If the operator is positioned after the source-ipv6-prefix / prefix-length argument, it must match the source port.
If the operator is positioned after the destination-ipv6-prefix / prefix-length argument, it must match the destination port.
The range operator requires two port numbers. All other operators require one port number.
The port argument is the decimal number of a TCP or UDP port. A port number is a number from 0 to 65535. The protocol-port argument is the name of a TCP or UDP port. TCP port names can be used only when filtering TCP. UDP port names can be used only when filtering UDP.
destination-ipv6-prefix / prefix-length
Destination IPv6 network or class of networks about which to set permit conditions.
This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
host destination-ipv6-address
Specifies the destination IPv6 host address about which to set permit conditions.
This destination-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
dscp value
(Optional) Matches a differentiated services code point (DSCP) value against the traffic class value in the Traffic Class field of each IPv6 packet header. Range is 0 to 63.
routing
(Optional) Matches source-routed packets against the routing extension header within each IPv6 packet header.
authen
(Optional) Matches if the IPv6 authentication header is present.
destopts
(Optional) Matches if the IPv6 destination options header is present.
fragments
(Optional) Matches noninitial fragmented packets where the fragment extension header contains a nonzero fragment offset. The fragments keyword is an option only if the operator [ port-number ] arguments are not specified.
log
(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by the logging console command.)
The message includes the access list name and sequence number, whether the packet was permitted; the protocol, whether it was TCP, UDP, ICMP, or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. The message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets permitted in the prior 5-minute interval.
log-input
(Optional) Provides the same function as the log keyword, except that the logging message also includes the input interface.
ttl
(Optional) Turns on matching against time-to-live (TTL) value.
operator
(Optional) Operand that compares the source or destination ports of the specified protocol. Operands are lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).
ttl value [value1 value2]
(Optional) TTL value used for filtering. Range is 1 to 255.
If only value is specified, the match is against this value.
If both value1 and value2 are specified, the packet TTL is matched against the range of TTLs between value1 and value2 .
icmp-off
(Optional) Turns off ICMP generation for denied packets
icmp-type
(Optional) ICMP message type for filtering ICMP packets. Range is from 0 to 255.
icmp-code
(Optional) ICMP message code for filtering ICMP packets. Range is from 0 to 255.
established
(Optional) For the TCP protocol only: Indicates an established connection.
match-any
(Optional) For the TCP protocol only: Filters on any combination of TCP flags.
match-all
(Optional) For the TCP protocol only: Filters on all TCP flags.
+ | -
(Required) For the TCP protocol match-any , match-all : Prefix flag-name with + or - . Use the + flag-name argument to match packets with the TCP flag set. Use the - flag-name argument to match packets when the TCP flag is not set.
flag-name
(Required) For the TCP protocol match-any , match-all . Flag names are: ack , fin , psh , rst , syn .
Command History
Release
Modification
Release 3.7.2
This command was introduced.
Release 4.0.1
The capture keyword was added. Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The permit (IPv6) command is similar to the permit (IPv4) command, except that it is IPv6-specific.
Use the permit (IPv6) command following the ipv6 access-list command to define the conditions under which a packet passes the access list.
Specifying ipv6 for the protocol argument matches against the IPv6 header of the packet.
By default, the first statement in an access list is number 10, and the subsequent statements are numbered in increments of 10.
You can add permit, deny, or remark statements to an existing access list without retyping the entire list. To add a new statement anywhere other than at the end of the list, create a new statement with an appropriate entry number that falls between two existing entry numbers to indicate where it belongs.
Both the source-ipv6-prefix/prefix-length and destination-ipv6-prefix/prefix-length arguments are used for traffic filtering (the source prefix filters traffic based upon the traffic source; the destination prefix filters traffic based upon the traffic destination).
Note
IPv6 prefix lists, not access lists, should be used for filtering routing protocol prefixes.
The fragments keyword is an option only if the operator [port | protocol-port] arguments are not specified.
Task ID
Examples
The following example shows how to configure the IPv6 access list named toCISCO and applies the access list to outbound traffic on GigabitEthernet interface 0/2/0/2. Specifically, the first deny entry in the list keeps all packets that have a destination TCP port number greater than 5000 from exiting out of GigabitEthernet interface 0/2/0/2. The second deny entry in the list keeps all packets that have a source UDP port number less than 5000 from exiting out of GigabitEthernet interface 0/2/0/2. The second deny entry also logs all matches to the console. The first permit entry in the list permits all ICMP packets to exit out of GigabitEthernet interface 0/2/0/2. The second permit entry in the list permits all other traffic to exit out of GigabitEthernet interface 0/2/0/2. The second permit entry is necessary because an implicit deny all condition is at the end of each IPv6 access list.
RP/0/RSP0/CPU0:router(config)# ipv6 access-list toCISCO RP/0/RSP0/CPU0:router(config-ipv6-acl)# deny tcp any any gt 5000 RP/0/RSP0/CPU0:router(config-ipv6-acl)# deny ipv6 any lt 5000 any log RP/0/RSP0/CPU0:router(config-ipv6-acl)# permit icmp any any RP/0/RSP0/CPU0:router(config-ipv6-acl)# permit any any RP/0/RSP0/CPU0:router(config)# interface gigabitethernet 0/2/0/2 RP/0/RSP0/CPU0:router(config-if)# ipv6 access-group tOCISCO outRelated Commands
Command
Description
Sets deny conditions for an IPv6 access list.
Defines an IPv6 access list and enters IPv6 access list configuration mode.
Inserts a helpful remark about an IPv6 access list entry.
Changes the starting entry number of the first statement in an existing IPv6 access list, and the number by which subsequent statements are incremented.
remark (IPv4)
To write a helpful comment (remark) for an entry in an IPv4 access list, use the remark command in IPv4 access list configuration mode. To remove the remark, use the no form of this command.
Syntax Description
sequence-number
(Optional) Number of the remark statement in the access list. This number determines the order of the statements in the access list. Range is 1 to 2147483646. (By default, the first statement is number 10; subsequent statements are incremented by 10.)
remark
Comment that describes the entry in the access list, up to 255 characters long.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the remark command to write a helpful comment for an entry in an IPv4 access list. To remove the remark, use the no form of this command.
The remark can be up to 255 characters; anything longer is truncated.
If you know the sequence number of the remark you want to delete, you can remove it by entering the no sequence-number command.
Use the resequence access-list ipv4 command if you want to add statements to an existing access list and the sequence numbers of consecutive entries do not permit additional statements.
Task ID
Examples
In the following example, the user1 subnet is not allowed to use outbound Telnet:
RP/0/RSP0/CPU0:router(config)# ipv4 access-list telnetting RP/0/RSP0/CPU0:router(config-ipv4-acl)# 10 remark Do not allow user1 to telnet out RP/0/RSP0/CPU0:router(config-ipv4-acl)# 20 deny tcp host 172.16.2.88 255.255.0.0 any eq telnet RP/0/RSP0/CPU0:router(config-ipv4-acl)# 30 permit icmp any any RP/0/RSP0/CPU0:router# show ipv4 access-list telnetting ipv4 access-list telnetting 0 remark Do not allow user1 to telnet out 20 deny tcp 172.16.2.88 255.255.0.0 any eq telnet out 30 permit icmp any anyRelated Commands
Command
Description
Sets the deny conditions for an IPv4 access list.
Defines an IPv4 access list and enters IPv4 access list configuration mode.
Sets the permit conditions for an IPv4 access list
Changes the starting entry number of the first statement in an existing IPv4 access list, and the number by which subsequent statements are incremented.
Displays the contents of all current IPv4 access lists.
remark (IPv6)
To write a helpful comment (remark) for an entry in an IPv6 access list, use the remark command in IPv6 access list configuration mode. To remove the remark, use the no form of this command.
Syntax Description
sequence-number
(Optional) Number of the remark statement in the access list. This number determines the order of the statements in the access list. Range is 1 to 2147483646. (By default, the first statement is number 10, and the subsequent statements are incremented by 10.)
remark
Comment that describes the entry in the access list, up to 255 characters long.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The remark (IPv6) command is similar to the remark (IPv4) command, except that it is IPv6-specific.
Use the remark command to write a helpful comment for an entry in an IPv6 access list. To remove the remark, use the no form of this command.
The remark can be up to 255 characters; anything longer is truncated.
If you know the sequence number of the remark you want to delete, you can remove it by entering the no sequence-number command.
Use the resequence access-list ipv6 command if you want to add statements to an existing access list and the sequence numbers of consecutive entries do not permit additional statements.
Task ID
Examples
In the following example, a remark is added:
RP/0/RSP0/CPU0:router(config)# ipv6 access-list Internetfilter RP/0/RSP0/CPU0:router(config-ipv6-acl)# 10 permit ipv6 3333:1:2:3::/64 any RP/0/RSP0/CPU0:router(config-ipv6-acl)# 20 permit ipv6 4444:1:2:3::/64 any RP/0/RSP0/CPU0:router(config-ipv6-acl)# 30 permit ipv6 5555:1:2:3::/64 any RP/0/RSP0/CPU0:router(config-ipv6-acl)# 39 remark Block BGP traffic from a given host RP/0/RSP0/CPU0:router(config-ipv6-acl)# 40 deny tcp host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range 1300 1400 RP/0/RSP0/CPU0:router# show ipv6 access-list Internetfilter ipv6 access-list Internetfilter 10 permit ipv6 3333:1:2:3::/64 any 20 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 any 39 remark Block BGP traffic from a given host 40 deny tcp host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range 1300 1400Related Commands
Command
Description
Sets the deny conditions for an IPv6 access list.
Defines an IPv6 access list and enters IPv6 access list configuration mode.
Sets permit conditions for an IPv6 access list
Changes the starting entry number of the first statement in an existing IPv6 access list, and the number by which subsequent statements are incremented.
resequence access-list ipv4
To renumber existing statements and increment subsequent statements to allow a new IPv4 access list statement (permit, deny, or remark) to be added, use the resequence access-list ipv4 command in EXEC mode.
Syntax Description
name
Name of an IPv4 access list.
base
(Optional) Number of the first statement in the specified access list, which determines its order in the access list. Maximum value is 2147483644. Default is 10.
increment
(Optional) Number by which the base sequence number is incremented for subsequent statements. Maximum value is 2147483644. Default is 10.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the resequence access-list ipv4 command to add a permit, deny, or remark statement between consecutive entries in an existing IPv4 access list. Specify the first entry number (the base) and the increment by which to separate the entry numbers of the statements. The software renumbers the existing statements, thereby making room to add new statements with the unused entry numbers.
Task ID
Examples
In the following example, suppose you have an existing access list:
ipv4 access-list marketing 1 permit 10.1.1.1 2 permit 10.2.0.0 0.0.255.255 3 permit tcp host 10.2.2.2 255.255.0.0 any eq telnetYou want to add additional entries in the access list. First you resequence the entries, renumbering the statements starting with number 20 and an increment of 5, and then you have room for four additional statements between each of the existing statements:
RP/0/RSP0/CPU0:router# resequence access-list ipv4 marketing 20 5 RP/0/RSP0/CPU0:router# show access-lists ipv4 marketing ipv4 access-list marketing 20 permit 10.1.1.1 25 permit 10.2.0.0 30 permit tcp host 10.2.2.2 255.255.0.0 any eq telnetNow you add your new entries.
RP/0/RSP0/CPU0:router(config)# ipv4 access-list marketing RP/0/RSP0/CPU0:router(config-ipv4-acl)# 3 remark Do not allow user1 to telnet out RP/0/RSP0/CPU0:router(config-ipv4-acl)# 4 deny tcp host 172.16.2.88 255.255.0.0 any eq telnet RP/0/RSP0/CPU0:router(config-ipv4-acl)# 29 remark Allow user2 to telnet out RP/0/RSP0/CPU0:router# show access-lists ipv4 marketing ipv4 access-list marketing 3 remark Do not allow user1 to telnet out 4 deny tcp host 171.69.2.88 255.255.0.0 any eq telnet 20 permit 10.1.1.1 25 permit 10.2.0.0 29 remark Allow user2 to telnet out 30 permit tcp host 10.2.2.2 255.255.0.0 any eq telnetRelated Commands
Command
Description
Sets the deny conditions for an IPv4 access list.
Defines an IPv4 access list and enters IPv4 access list configuration mode.
Sets the permit conditions for an IPv4 access list
Inserts a helpful remark about an IPv4 access list.
Displays the contents of all current IPv4 access lists.
resequence access-list ipv6
To renumber existing statements and increment subsequent statements to allow a new IPv6 access list statement (permit, deny, or remark) to be added, use the resequence access-list ipv6 command in EXEC mode.
Syntax Description
name
Name of an IPv6 access list.
base
(Optional) Number of the first statement in the specified access list, which determines its order in the access list. Maximum value is 2147483646. Default is 10.
increment
(Optional) Number by which the base sequence number is incremented for subsequent statements. Maximum value is 2147483644. Default is 10.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The resequence access-list ipv6 command is similar to the resequence access-list ipv4 command, except that it is IPv6 specific.
Use the resequence access-list ipv6 command to add a permit, deny, or remark statement between consecutive entries in an existing IPv6 access list. Specify the first entry number (the base) and the increment by which to separate the entry numbers of the statements. The software renumbers the existing statements, thereby making room to add new statements with the unused entry numbers.
Task ID
Examples
In the following example, suppose you have an existing access list:
ipv6 access-list Internetfilter 10 permit ipv6 3333:1:2:3::/64 any 20 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 anyYou want to add additional entries in the access list. First, you resequence the entries, renumbering the statements starting with number 20 and an increment of 5, and then you have room for four additional statements between each of the existing statements:
RP/0/RSP0/CPU0:router# resequence access-list ipv6 Internetfilter 20 5 RP/0/RSP0/CPU0:router# show access-lists ipv6 Internetfilter ipv6 access-list Internetfilter 20 permit ipv6 3333:1:2:3::/64 any 25 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 anyNow you add your new entries.
RP/0/RSP0/CPU0:router(config)# ipv6 access-list Internetfilter RP/0/RSP0/CPU0:router(config-ipv6-acl)# 3 remark Block BGP traffic from a given host RP/0/RSP0/CPU0:router(config-ipv6-acl)# 4 deny tcp host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range 1300 1400 RP/0/RSP0/CPU0:router# show access-lists ipv6 Internetfilter ipv6 access-list Internetfilter 3 remark Block BGP traffic from a given host 4 deny tcp host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range 1300 1404 deny tcp host 171.69.2.88 255.255.0.0 any eq telnet 20 permit ipv6 3333:1:2:3::/64 any 25 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 anyshow access-lists afi-all
To display the contents of current IPv4 and IPv6 access lists, use the show access-lists afi-all command in EXEC mode.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
show access-lists ipv4
To display the contents of current IPv4 access lists, use the show access-lists ipv4 command in EXEC mode.
show access-lists ipv4 [ access-list-name hardware { ingress | egress } [ interface type interface-path-id ] { sequence number | location node-id } | summary [access-list-name] | access-list-name [sequence-number] | maximum [detail] [ usage pfilter { location node-id | all } ] ]
Syntax Description
access-list-name
(Optional) Name of a particular IPv4 access list. The name cannot contain spaces or quotation marks, but can include numbers.
hardware
(Optional) Identifies the access list as an access list for an interface.
ingress
(Optional) Specifies an inbound interface.
egress
(Optional) Specifies an outbound interface.
interface
(Optional) Displays interface statistics.
type
(Optional) Interface type. For more information, use the question mark (?) online help function.
interface-path-id
Physical interface or virtual interface.
Note Use the show interfaces command to see a list of all interfaces currently configured on the router.
For more information about the syntax for the router, use the question mark (?) online help function.
sequence number
(Optional) Sequence number of a particular IPv4 access list. Range is 1 to 2147483644.
location node-id
(Optional) Location of a particular IPv4 access list. The node-id argument is entered in the rack/slot/module notation.
summary
(Optional) Displays a summary of all current IPv4 access lists.
sequence-number
(Optional) Sequence number of a particular IPv4 access list. Range is 1 to 2147483644.
maximum
(Optional) Displays the current maximum number of configurable IPv4 access control lists (ACLs) and access control entries (ACEs).
detail
(Optional) Displays complete out-of-resource (OOR) details.
usage
(Optional) Displays the usage of the access list on a given line card.
pfilter
(Optional) Displays the packet filtering usage for the specified line card.
all
(Optional) Displays the location of all the line cards.
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show access-lists ipv4 command to display the contents of all IPv4 access lists. To display the contents of a specific IPv4 access list, use the name argument. Use the sequence-number argument to specify the sequence number of the access list.
Use the hardware , ingress or egress , and location keywords to display the access list hardware contents and counters for all interfaces that use the specified access list in a given direction (ingress or egress). To display the contents of a specific access list entry, use the sequence number keyword and argument. The access group for an interface must be configured using the ipv4 access-group command for access list hardware counters to be enabled.
Use the show access-lists ipv4 summary command to display a summary of all current IPv4 access lists. To display a summary of a specific IPv4 access list, use the name argument.
Use the show access-lists ipv4 maximum detail command to display the OOR details for IPv4 access lists. OOR limits the number of ACLs and ACEs that can be configured in the system. When the limit is reached, configuration of new ACLs or ACEs is rejected.
Use the show access-list ipv4 usage command to display a summary of all interfaces and access lists programmed on the specified line card.
Task ID
Examples
In the following example, the contents of all IPv4 access lists are displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv4 ipv4 access-list 101 10 deny udp any any eq ntp 20 permit tcp any any 30 permit udp any any eq tftp 40 permit icmp any any 50 permit udp any any eq domain ipv4 access-list Internetfilter 10 permit tcp any 172.16.0.0 0.0.255.255 eq telnet 20 deny tcp any any 30 deny udp any 172.18.0.0 0.0.255.255 lt 1024 40 deny ipv4 any any logIn the following example, the contents of an access list named acl_hw_1 are displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv4 acl_hw_1 hardware egress location 0/2/cp0 ipv4 access-list acl_hw_1 10 permit icmp 192.168.36.0 0.0.0.255 any (251 hw matches) 20 permit ip 172.16.3.0 0.0.255.255 any (29 hw matches) 30 deny tcp any any (58 hw matches)
This table describes the significant fields shown in the display.
Table 1 show access-lists ipv4 hardware Field DescriptionsField
Description
hw matches
Number of hardware matches.
next-hop
Next hop is programmed and is reachable through FIB.
ACL name
Name of the ACL programmed in hardware.
Sequence Number
Each ACE sequence number is programmed into hardware with all the fields that are corresponding to the values set in ACE.
Grant
Depending on the ACE rule, the grant is set to deny, permit, or both.
Logging
Logging is set to on if ACE uses a log option to enable logs.
Per ace icmp
If Per ace icmp is set to on in the hardware, ICMP is unreachable, is rate-limited, and is generated. The default is set to on.
Hits
Hardware counter for that ACE.
Statistics pointer
Statistics pointer is the pointer that is assigned for hardware counters.
Number of TCAM entries
Number of TCAM entries that are used to program the ACE into hardware.
In the following example, a summary of all IPv4 access lists are displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv4 summary ACL Summary: Total ACLs configured: 3 Total ACEs configured: 11
This table describes the significant fields shown in the display.
Table 2 show access-lists ipv4 summary Field DescriptionsField
Description
Total ACLs configured
Number of configured IPv4 ACLs.
Total ACEs configured
Number of configured IPV4 ACEs.
In the following example, the OOR details of the IPv4 access lists are displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv4 maximum detail Default max configurable acls :5000 Default max configurable aces :200000 Current configured acls :1 Current configured aces :2 Current max configurable acls :5000 Current max configurable aces :200000 Max configurable acls :9000 Max configurable aces :350000
This table describes the significant fields shown in the display.
Table 3 show access-lists ipv4 maximum detail Command Field DescriptionsField
Description
Default max configurable acls
Default maximum number of configurable IPv4 ACLs allowed.
Default max configurable aces
Default maximum number of configurable IPv4 ACEs allowed.
Current configured acls
Number of configured IPv4 ACLs.
Current configured aces
Number of configured IPv4 ACEs.
Current max configurable acls
Configured maximum number of configurable IPv4 ACLs allowed.
Current max configurable aces
Configured maximum number of configurable IPv4 ACEs allowed.
Max configurable acls
Maximum number of configurable IPv4 ACLs allowed.
Max configurable aces
Maximum number of configurable IPv4 ACEs allowed.
Related Commands
Command
Description
Resets the IPv4 access list match counters.
Copies an existing IPv4 access list.
Sets the deny conditions for an IPv4 access list.
Filters incoming or outgoing IPv4 traffic on an interface.
Defines an IPv4 access list and enters IPv4 access list configuration mode.
Sets the permit conditions for an IPv4 access list
Inserts a helpful remark about an IPv4 access list entry.
Changes the starting entry number of the first statement in an existing IPv4 access list, and the number by which subsequent statements are incremented.
show access-lists ipv6
To display the contents of current IPv6 access lists, use the show access-lists ipv6 command in EXEC mode.
show access-lists ipv6 [ access-list-name hardware { ingress | egress } [ interface type interface-path-id ] { sequence number | location node-id } | summary [access-list-name] | access-list-name [sequence-number] | maximum [detail] [ usage pfilter { location node-id | all } ] ]
Syntax Description
Command History
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show access-lists ipv6 command is similar to the show access-lists ipv4 command, except that it is IPv6 specific.
Use the show access-lists ipv6 command to display the contents of all IPv6 access lists. To display the contents of a specific IPv6 access list, use the name argument. Use the sequence-number argument to specify the sequence number of the access list.
Use thehardware , ingress or egress, and location keywords to display the access list hardware contents and counters for all interfaces that use the specified access list in a given direction (ingress or egress). To display the contents of a specific access list entry, use the sequence number keyword and argument. The access group for an interface must be configured using the ipv6 access-group command for access list hardware counters to be enabled.
Use the show access-lists ipv6 summary command to display a summary of all current IPv6 access lists. To display a summary of a specific IPv6 access list, use the name argument.
Use the show access-lists ipv6 maximum detail command to display the OOR details for IPv6 access lists. OOR limits the number of ACLs and ACEs that can be configured in the system. When the limit is reached, configuration of new ACLs or ACEs is rejected.
Use the show access-list ipv6 ipv4 usage command to display a summary of all interfaces and access lists programmed on the specified line card.
Task ID
Examples
In the following example, the contents of all IPv6 access lists are displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv6 ipv6 access-list Internetfilter 3 remark Block BGP traffic from a given host 4 deny tcp host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range 1300 1404 deny tcp host 171.69.2.88 255.255.0.0 any eq telnet 20 permit ipv6 3333:1:2:3::/64 any 25 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 any ipv6 access-list marketing 10 permit ipv6 7777:1:2:3::/64 any (51 matches) 20 permit ipv6 8888:1:2:3::/64 any (26 matches) 30 permit ipv6 9999:1:2:3::/64 any (5 matches)In the following example, the contents of an access list named Internetfilter is displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv6 Internetfilter ipv6 access-list Internetfilter 3 remark Block BGP traffic from a given host 4 deny tcp host 6666:1:2:3::10 eq bgp host 7777:1:2:3::20 range 1300 1404 deny tcp host 171.69.2.88 255.255.0.0 any eq telnet 20 permit ipv6 3333:1:2:3::/64 any 25 permit ipv6 4444:1:2:3::/64 any 30 permit ipv6 5555:1:2:3::/64 anyIn the following example, the contents of an access list named acl_hw_1 is displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv6 acl_hw_1 hardware egress location 0/2/cp0 ipv6 access-list acl_hw_1 10 permit icmp any any (251 hw matches) 20 permit ipv6 3333:1:2:3::/64 any (29 hw matches) 30 deny tcp any any (58 hw matches)
This table describes the significant fields shown in the display.
Table 4 show access-lists ipv6 hardware Command Field DescriptionsField
Description
hw matches
Number of hardware matches.
In the following example, a summary of all IPv6 access lists is displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv6 summary ACL Summary: Total ACLs configured: 3 Total ACEs configured: 11
This table describes the significant fields shown in the display.
Table 5 show access-lists ipv6 summary Command Field DescriptionsField
Description
Total ACLs configured
Number of configured IPv6 ACLs.
Total ACEs configured
Number of configured IPV6 ACEs.
In the following example, the OOR details of the IPv6 access lists are displayed:
RP/0/RSP0/CPU0:router# show access-lists ipv6 maximum detail Default max configurable acls :1000 Default max configurable aces :50000 Current configured acls :1 Current configured aces :2 Current max configurable acls :1000 Current max configurable aces :50000 Max configurable acls :2000 Max configurable aces :100000Related Commands
Command
Description
Copies an existing IPv6 access list.
Sets the deny conditions for an IPv6 access list.
Defines an IPv6 access list and enters IPv6 access list configuration mode.
Set permit conditions for an IPv6 access list.
Inserts a helpful remark about an IPv6 access list entry.
Changes the starting entry number of the first statement in an existing IPv4 access list, and the number by which subsequent statements are incremented.
