Cisco IOS Release 15.6(3)M1 - Release Notes for Cisco IR800 Industrial Integrated Services Routers, Cisco 1000 and 2000 Series Connected Grid Routers

---

---

---

---

Modem	SIM	Interface	Controller
Modem 0	Slot 0	Cellular 0/0 and Cellular 0/1	Controller 0
Modem 1	Slot 1	Cellular 1/0 and Cellular 1/1	Controller 1

CGR Compute Module

The CGR Compute Module, is a modular, hardened server module for CGR 1000 routers. The compute module runs on Cisco IOx, a hypervisor architecture. Customers can run Internet of Things (IoT) applications on a Virtual Machine (VM) and connect legacy networking technologies through a network interface card. The compute module functions as a fog computing node at the edge of the network.

Minimum software requirements:

• Cisco IOS 15.6(3)M1 for CGR 1000 Routers
• Cisco IOx Release 1.2.0

For additional information, see the Release Notes for Cisco IOx, Release 1.2.0:

http://www.cisco.com/c/en/us/td/docs/routers/access/800/software/guides/iox/release-notes/iox120rn.html

4G LTE IPv6 Support

Support has been added to open up IPv6 configuration for cellular interface if it is a 4G interface.

The following example shows the steps to create an IPV6 profile, show the IOS configuration interface, verify the IPv6 address, and then test using the ping command.

---

Step 1 Create the IPV6 profile for cellular interface.

Step 2 Show the running configuration.

Step 3 Verify the IPV6 address on cellular interface.

Step 4 Test with the ping command.

 

Support for Flexible Mesh Key Lifetime and PTK/PMK Multiplier

A new command line interface was added to change gtk, pmk and ptk lifetimes.

The following is an example to illustrate the new CLI:

Support Multiple UDP Ports for Multicast Traffic Forwarding

A new command line interface was added for wpan multicast-agent optional ports.

The following is an example to illustrate the new CLI:

Scale up to 50,000 BACT devices

Support has been added to make the dot1x authentication optimization setting configurable. There is a new command setting in the WPAN interface mode to enable (for memory reduction) or disable the preservation of the dot1x authenticated sessions.

The following is an example to illustrate the new CLI:

Accelerometer and Gyroscope Support

Support has been added to enable an existing hardware feature on the IR829 in software in order to track the speed and angular movement of the device.

Two configuration CLIs and one show CLI are introduced:

Once this is enabled, gyroscope reading will start by the frequency currently set.

Default frequency is 1/sec. If this is configured, it would overwrite default frequency and any later reading would be according to the newly set frequency.

This CLI would only show data if "gyroscope-reading" is enabled. All readings since start (unless wrap-around occurs, which means table is full), would be shown in the order from the most recent to the oldest.

Each entry shows G-X, Y, Z(3D gyroscope data) in mdps (Milli Degrees Per Second) and XL-X,Y, Z (3D accelerator data) in unit mg (milli g forces) where g is ≈ 9.81 m/s ².

---

Note Configurations would be in running-config and would stay over reload if saved.

IOXVM Storage Partition Enhancement

This enhancement to the IR800 series is to provide more flexibility to provide a customizable disk partitioning. With a smaller partition for system files, the user can put larger applications in the remaining partition.

A new CLI is introduced for this purpose:

The user can input a number between 30 and 90 which would be rounded up to multiples of 5.

For example, typing in 30 means the system partition would take 30% of total space.

IOS communicates with VDS, which will actually perform disk repartition for GOS. After the action is completed by VDS, VDS will send a notification message back to IOS to indicate the status of operation.

After the disk repartitioning, the user will need to reinstall the GOS.

After the repartition is successful, you should see the following syslog message:

After the disk is repartitioned, the GOS needs to be reinstalled by one of two methods:

Finally, manually restart the GOS.

IOXVM Graceful Shutdown

On the CGR1000, and the IR800 platforms, the Guest OS will now perform a graceful shutdown before a reload of the device. Previously, the GOS would not go through the shutdown command, which sometimes would result in unexpected behavior.

Support for New Modems and Dual Modems

Support has been added for dual active LTE radios. There are two new modems available, the MC7455 and MC7430. This provides Multi-carrier support for active and backup use cases.

There are new SKUs that utilize these modems:

---

Cisco IOS Release 15.6(3)M1

The following sections list caveats for Cisco IOS Release 15.6(3)M1:

Open Caveats

• CSCvc53524

On the IR800 or the CGR1K platforms, the MC73XX modem Firmware cannot be upgraded on the 15.6(3)M1 image.

Conditions :

The ' microcode reload ' command will fail to upgrade the modem Firmware. After a modem power-cycle, the platform should be able to work on the previous modem Firmware.

Workaround :

Either wait for the IOS fix following version 15.6(3)M1, or stay with current MC73XX modem Firmware.

• CSCvc53541

Application Hosting from IOx may not work.

Symptoms :

– No access to local manager

– Cannot access device from fog director

– unable to manually start applications

– CAF does not start

– The product ID value in CAF is 'default', when it should update with the product ID sent by IOS.

Workaround:

1. Login to IOx. The simplest method is to reverse telnet to the g0 interface on an IR809, or the g5 interface on an IR829 using port 2070. For Example:

2. Ensure Line1/4 has ' transport input/output all ' on it.

3. Ensure IPv6 is enabled in the IOx interface.

4. Once logged in, check the following:

The most likely status is that CAF will be stopped.

5. To resolve the problem:

6. Restart CAF again.

7. Verify that CAF is up.

CAF should be in a RUNNING state.

• CSCvc12365

On the 800 series routers, configured with Dialer Watch configurations, if the interface cellular is up and device is reloaded, the dial-out does not happen and IP does not appear on cellular interface.

Workaround :

Perform a shut then noshut on the cellular interface.

• CSCuu49331

LED status report for PoE is inconsistent across different commands.

Workaround :

None

• CSCuy79750

After completion of a bundle installation, the Guest OS might not function.

Conditions :

Perform a bundle installation with the Guest OS running. After the bundle installation is completed with Guest OS updated, the device needs to be reloaded.

Workaround:

It is recommended to shutdown the Guest OS before performing a bundle install. After the bundle installation is completed, the device needs to be reloaded.

• CSCuz40849

Cisco IOS cannot decode certificate lifetime past the year 2099

Conditions :

The validity end-time for either CA certificate or certificates must be 2099 or earlier. Cisco IOS cannot decode dates past 2099. BER/DER decoding failure will be generated during authentication and enrollment phases.

Workaround:

None

• CSCuz51085

Registration on the CGR1K, IR800, and C819 will always fails after a flash format or folder deletion.

Conditions :

Once a device has been tunnel-provisioned (including those that have been registered to FND), any attempt to format its flash partition or delete the managed folder on the flash will cause any future registration (e.g. after a router reload, or a fresh ZTD operation) to fail.

Sample Registration Failure :

java.io.IOException: Failed to retrieve inventory from device. Reason: [invalid cli command] Sent [[show iox host list detail | format flash:/managed/odm/cg-nms.odm, show iox application list | format flash:/managed/odm/cg-nms.odm]]

Workaround:

Access the FND's Oracle database and delete the MD5 checksum of the updated odm file for these eid's from the database.

• CSCuz66824

The alarm contact configuration command syntax changed in 15.6(3)M.

Conditions :

In the 15.6(3)M or later releases, there is a slight change in the command syntax for the alarm contact configuration. If alarm contact is configured in IOS images prior to 15.6(3)M, and the device is upgraded to15.6(3)M, the alarm contact will need to be reconfigured using the new command syntax. Otherwise, the alarm contact setting will be lost.

Command Syntax Difference:

Pre-15.6(3)M with hyphen between alarm and contact:

Post-15.6(3)M with no hyphen between alarm and contact:

Workaround:

Reconfigure the alarm contact after upgrading to 15.6(3)M.

• CSCuu60617

Media-type rs485 is configurable under IR800 serial port 0 interface (async1), however the serial port 1 (async1) interface does not support media-type rs485.

Conditions : When you configure 'media-type rs485" under the async1 interface, the configuration is acceptable.

Workaround : None

• CSCux43383

On the IR829 with a 4GModem, the modem can enter into an unknown state after several modem resets.

Conditions : After 100+ modem resets and attach to BSS, the modem enters into a state where it no longer displays modem info on IOS ( show cellular 0 all). It neither attaches to the BSS or sends IP traffic. Modem seems to respond to the AT commands.

Workaround : None

• CSCuy83574

Enabling GPS on the CGR1000 3G/4G cellular controller will lock up the console.

Conditions : The regular GPS settings for 3G or 4G cellular controller in the CGR1000 routers must not be used. Cellular modem-based GPS in CGR1000 routers is not supported.

Workaround : Only a CONFIG RESET button recovery may help to restore the CGR1000 back to working condition.

• CSCuy91651

Inconsistent version numbering for the Ref-GOS image name in the IR800 bundle image.

Conditions : In the IR800 bundle image, the REF GOS image name is: ir800-ref-gos.img.2.3.gz.

Installing the GOS image will produce this version string:

Installation: Cisco-GOS,version-1.0.0.2

Guest OS status:

I nstallation: Cisco-GOS,version-1.0.0.2

The IR800 GOS image is properly versioned in the form: ir800-ioxvm-1.0.0.x

Workaround : None

• CSCvd30726

No negotiation auto not possible on onboard int gig0/1.

Conditions : Configuring interface with SFP

Workaround : None

• CSCvf75957

Problem Description :

Bundle install failure/timeout, IOx failure

Symptoms:

1. ping to VDS fails:

2. bundle install times out

3. iox applications are not accessible anymore

Conditions:

Typically, when the router is left idle for many weeks and months, there is a possibility to observe this when upgrading to the next software image.

Root Cause:

Root cause was that dual modem logs in VDS were not rotating and size increased in time. Due to lack of memory, bundle install attempts failed. Reload the router before reattempting bundle install and image upgrade.

Issue is seen in all software images supporting dual modem [15.6(3)M and beyond]

Workaround :

Reload IOS and system will recover.

• CSCvd41974

Problem Description :

On IR829 and IR809 platform, there is a Wpan2 interface shown by default in 15.6(3)M2 and beyond software images.

Condition :

The show run command will by default show an additional interface, regardless of whether LoRa modem is attached or not.

Workaround :

None

Closed Caveats

The following caveats are fixed with this release:

• CSCuy79750

After completion of a bundle installation, the Guest OS might not function.

Conditions :

Perform a bundle installation with the Guest OS running. After the bundle installation is completed with Guest OS updated, the device needs to be reloaded.

• CSCuy91636

CGR1000 GOS image version is not matching the version in the filename.

Conditions : The version in the CGR1000 GOS file name " cgr1000-ref-gos.img.1.30.gz " is 1.30, but after a bundle install and restarting the IOX VM, the GOS version being retrieved from " sh platform guest-os " is 1.29.

• CSCvb00767

On the IR800, need to reload router once VDS lost connection.

Symptom :

The IR800 watchdog monitors the VDS communication from IOS. This modification to the watchdog tracks the number of missed heartbeats from VDS. When missed heartbeats reaches its limit (i.e. 60), the watchdog will trigger a system reload with a "VDS communication failure" message.

• CSCva66036

After upgrading the modem on a CGR1240, the modem needed to be power-cycled in order to bring it up.

• CSCva32006

When executing a series of show and configuration commands quickly on an ISR-G2, via an SSH session, an SSH Process Thrash message is generated.

Workaround :

When executing multiple commands, wait a few seconds between each command.

 

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

 

© 2016 Cisco Systems, Inc. All rights reserved.

Printed in the USA on recycled paper containing 10% postconsumer waste.