E1 R2 Customization with cas-custom Command
Available Languages
Introduction
This document describes that the cas-custom command under the controller E1 is used in order to customize the E1 R2 country variants and Channel Associated Signaling (CAS) parameters. This document needs to be used in conjunction with the E1 R2 Signaling Theory and the E1 R2 Configuration and Troubleshooting documents.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on these software and hardware versions:
- Cisco 2911 router
- Cisco IOS® Software Release 15.4(3)M4
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
E1 R2 Customization
The subcommands under the command cas-custom are used in order to accommodate the country variants and to customize CAS parameters.
This command sequence illustrates how you can view all cas-custom subcommand options:
E1R2Router(config)#controller E1 0/0/0
E1R2Router(config-controller)#ds0-group 1 timeslots 2 type r2-digital r2-compelled ani
E1R2Router(config-controller)#cas-custom 1
E1R2Router(config-ctrl-cas)#?
CAS custom commands:
alert-wait-time Time to wait for alert indication for incoming R2 calls ani-digits Expected number of ANI digits ani-timeout Timeout for ANI digits answer-guard-time Wait Between Group-B Answer Signal And Line Answer answer-signal Answer signal to be used caller-digits Digits to be collected before requesting CallerID category Category signal cc-reanswer-to Collect Call Reanswer TO country Country Name debounce-time Debounce Timer default Set a command to its defaults disconnect-tone Provide tone to the calling party after sending group B register signal dnis-complete Send I-15 after DNIS digits for dial-out dnis-digits Expected number of DNIS digits double-answer Send Double Answer To Block Collect Calls dtmf DTMF Inter Digit Timer in MilliSeconds exit Exit from cas custom mode groupa-callerid-end Send Group-A Caller ID End invert-abcd invert the ABCD bits before tx and after rx ka KA Signal kd KD Signal metering R2 network is sending metering signal mfc-signal-level R2 MFC signal level nc-congestion Non Compelled Congestion signal (applicable to semi-compelled and compelled) no Negate a command or set its defaults proceed-to-send Suppress proceed-to-send signal for pulsed line signaling reanswer-time Reanswer Timer release-ack Send Release Acknowledgement to Clear Forward release-guard-time Release Guard Timer request-category DNIS Digits to be collected before requesting category seizure-ack-time Seizure to Acknowledge timer signal-end-to-end Transfer R2 Category and Answer signals end-to-end timer configure timer trunk-group Configure interface to be in a trunk group unused-abcd Unused ABCD bit values
The command ds0-group 1 timeslots 2 type r2-digital r2-compelled ani needs to be used intially only to create the ds0-group. The cas-custom command with group number can be used whenever needed in order to customize the group.
Cisco recommends that you first configure the country country name use-default parameter in order to set all related parameters accordingly to the country supported. Use the other cas-custom subcommands for further customization required in order to accommodate a certain Private Branch Exchange (PBX) or switch.
Customization needs to be entered after the country has been selected, or the CAS parameters return to default. In this example, the last statement returns all CAS parameters to the default settings for Brazil which voids the caller-digits 4 command:
(config-controller)#cas-custom 1 (config-ctrl-cas)#country brazil use-default (config-ctrl-cas)#caller-digits 4 (config-ctrl-cas)#country brazil use-default
Now that you know how to view the cas-custom command parameters, this table details these parameters and their respective uses.
| Command Parameter | Description |
|---|---|
| ani-digits min 0-64 max 0-64 | If your router does not receive the minimum number of Automatic Number Identification (ANI) digits, it clears the call. After the router collects the maximum number of ANI digits, it sends Caller ID End and does not wait for the Forward Group-I-15 signal. |
| ani-timeout 1-15 seconds | Default last-tone-timeout is three seconds. Some switches take longer than three seconds to pulse out ANI digits. Therefore, this is made configurable. If the router times out while it waits for ANI digits and aborts the call, increase this timer argument. |
| caller-digits 1-64 | International Telecommunication Union (ITU) default is 1. This means that the router requests ANI after it receives the first Dialed Number Information Service (DNIS) digit. |
| groupa-callerid-end | Countries like China, Thailand, and Mexico use Group-C signals for ANI collection. If this is configured, the router uses the Backward Group-A-1 signal as Caller ID End. If it is not configured, the router uses the country default, which might be a Group-C signal. |
| kA 1-15 | This is used in China. This is the category of the calling party sent in response to Backward Group-A-6 signal. For incoming calls, the router collects the kA value. For outgoing calls, the router sends kA if configured. Otherwise, the router sends the default category for the country. |
| kd 1-15 | This is used in China. This is the category sent in response to Backward Group-A-3 signal. For incoming calls, the router collects the kd value. For outgoing calls, the router sends kd if configured. Otherwise, it sends the default category for the country. |
| dnis-digits min 1 max 1-64 | If the router does not know the number of DNIS digits beforehand, it has to rely on a timeout mechanism (three seconds) in order to detect the end of DNIS. The configuration of max speeds up the call setup time by three seconds. |
| dnis-complete | Sends Forward Group-I-15 signal after dialing out all the DNIS digits. Effective for outgoing calls only. Configure this if the switch requires it, or if it improves call setup time by three seconds. The dnis-complete parameter is a requirement on the switch side. For instance, in the Philippines, if the Forward Group-I-15 signal is not sent, outgoing calls do not complete. Therefore, this was implemented. |
| answer-signal {group-a | group-b} 1-15 | By default, the router sends Backward Group-A-3 (address complete, change over to Group-B) after DNIS/ANI collection. When a switch sends the Group-II category, the router sends a Group-B answer signal and connects. If Group-A answer signal (A-6) is configured, then the router does not send A-3 after address collection. It sends A-6 and then connects. |
| request-category 1-64 | If this is configured, the router requests for the category after it collects "request-category" number of DNIS digits for incoming calls only. If this parameter is not configured, the router asks for the category only after address collection by sending the Backward Group-A-3 signal. |
| category 1-15 | Specifies the type of call (subscriber with priority or normal subscriber). ITU default is 1 (normal subscriber). For outgoing calls, the router sends this category. If this is not configured, the router sends the country default category. For incoming calls, the router collects the category from the switch. No special handling is based on the category. |
| NC-congestion 1-15 | This is the Backward Group-B congestion signal for non-compelled signaling. If this is not configured, the router uses the default Backward Group-B-4 signal. |
| country use-defaults | Always initially configure with the country use-defaults parameter. This loads the default register signals for that country. You can then customize based on the switch after the register signals load. |
| answer-guard-time 1-1000 msecs | This is the wait between the router that sends register answer Backward Group-(B1 or B6) signal and line ANSWER (01). Default is one second. If Ring No Answers (RNAs, which are calls that fail in the signaling stage) happen during this wait, or if you want to speed up the call setup time, decrease this timer. |
| debounce-time 10-40 msecs | Any line signaling change is considered valid only if it lasts at least the length of this timer. The default is 40 msecs for all countries. Tune this based on the switch. |
| release-guard-time 1-2000 msecs | The router starts this timer on receiving the clear-forward signal from the switch. It then sends idle up on expiration of this timer. The default is two seconds. Match this timer to the switch configuration. |
| seizure-ack-time 2-100 msecs | This is the delay between the router that receives seizure and sends seizure acknowledgment (ACK). This timer is configurable only on AS5200s and AS5300s. On AS5800s, there is no delay. Tune this based on the switch requirements. |
| metering | Metering signals are pulse type signals transmitted backwards during the call from call charging point to subscriber's call meter in the originating exchange. This pulse can be "pulsed clear-back" (01 to 11 and back) or "pulsed answer" (11 to 01 and back). In order to avoid confusion with metering signals, clear-back signal is not allowed. If metering is on, the router sends Forced Release (00) instead of Clear-Back (11). |
| invert-abcd 0|1 0|1 0|1 0|1 | Inverts the ABCD status bits in time-slot 16 before TX and after rx. If A bit is set to 1, the router inverts the bit before it transmits and after it receives. For example, invert-abcd 1 0 0 0 causes only bit A to be inverted. |
| unused-abcd 0|1 0|1 0|1 0|1 | R2 signaling uses the A,B status bits only. This command sets the unused C,D bits. Default unused C,D bits for all countries except China is 01. For China, C,D bits are 11. |
| release-ack | If this is configured, the router sends ACK (11) to the clear-forward signal from the switch. Currently not supported on AS5800. Originally implemented for Malta. |
| proceed-to-send |
ITU pulsed line signaling (S-7) ACKs the seizure with a proceed-to-send signal (150 ms pulse). A variant of this signaling over satellite links does not use this signal. If this is configured, the router does not ACK the seizure for incoming calls and does not expect ACK for outgoing calls. This affects pulsed line signaling calls only. Not supported on AS5800 yet. |
| cc-reanswer-to |
Specifies the time out value, in milliseconds (ms), for double answer duration. The range is from 1000 to 120000. Default value is 3000 ms (3 seconds). The default value can be changed only if the double-answer comes in later than three seconds during the lab testing. |
| dtmf timer-inter-digit milliseconds |
Configures the DTMF interdigit timer for a DS0 group. |
| mfc-signal-level | Configure MFC signal level between -31 to -5 dBm . |
| reanswer-time |
Reanswer Time in Milliseconds . Range : 1000-120000 |
| timer last-tone-off outgoing |
In order to adjust the timeout value of waiting for the far-end stop the last register signal. Range : 1-10 |
More information on Country Options, refer to Country Options Configuration for E1 R2 Signaling.
Related Information
- E1 R2 Signaling Theory
- E1 R2 Configuration and Troubleshooting
- E1 R2 Signaling for the Cisco AS5300 and Cisco AS5200 Access Servers
- E1 R2 Signaling for the Cisco 3620 and 3640 Series Routers
- Voice Technologies
- Voice and Unified Communications Products
- Troubleshooting Cisco IP Telephony
- Technical Support - Cisco Systems
FeedbackContact Cisco
- Open a Support Case
- (Requires a Cisco Service Contract)